# Bombardier Service Bulletin 604-27-041

Copy: No revision named ("604-27-041 Basic"), 11 pages: PDF https://openairdocs.org/files/sha256/19/40/194068c0eabcf89f2ccc5cac029dc7e065547819024f658f8c75230159417900; text https://openairdocs.org/service-documents/bombardier/sb-604-27-041/file/194068c0eabc.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2025-0483; AD 2025-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 604-27-041
- Page: https://openairdocs.org/service-documents/bombardier/sb-604-27-041

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2025-22-04](https://openairdocs.org/ad/2025-22-04.md), effective Dec 23, 2025: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-604-27-041/proposed.md).

## Text (11 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2025-0483; AD 2025-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM ON-BOARD
RECORDER (FSOBR)/FLAP ON-BOARD RECORDER (FOBR) HARNESS
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 1000 flight hours or 14 months from
this Service Bulletin release date (Basic
Issue)
EFFECTIVITY: CL−600−2B16 aircraft, Serial No. 5301 to 5665
MANPOWER: 2 Man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS NOYES
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive.
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL CL−600−2B16
ATA 27−50
FLIGHT CONTROLS
Basic Issue: May 20/2024 604−27−041
Page 1 of 1
This Service Bulletin is available at:

### Page 2

MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM ON-BOARD
RECORDER (FSOBR)/FLAP ON-BOARD RECORDER (FOBR) HARNESS
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is only applicable to aircraft Post SB 604−27−035,
which has Flap System On−Board Recorder (FSOBR)/Flap On−Board
Recorder (FOBR) option installed.
A. Effectivity
CL−600−2B16 aircraft, Serial No. 5301 to 5665.
The intent of this Service Bulletin was met on the aircraft that follows with Service
Non−Incorporated Engineering Orders (SNIEO) listed in the table that follows:
AIRCRAFT SERIAL NO. DRAWING 604-57140, SNIEO NO.
5396 S50
5590 S43
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
Objective/Benefit:
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL CL−600−2B16
ATA 27−50
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2024 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: May 20/2024 604−27−041
Page 1 of 8
This Service Bulletin is available at:

### Page 3

This Service Bulletin instructs to cap and stow the Flap System On−Board
Recorder (FSOBR)/Flap On−Board Recorder (FOBR) harness, Part
No. 604−70201−1.
C. Description
This Service Bulletin gives instructions to:
− Get access to the avionic bay, right side, between FS 280.00 and FS 310.00,
− Disconnect the FSOBR/FOBR harness connectors,
− Cap and stow the FSOBR/FOBR harness,
− Reconnect the connectors P1CE and P9CE to J1CE and J9CE respectively,
and
− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended within 1000 flight hours or 14 months, whichever comes first from
this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin. Standard
SRPSA fees may apply. Refer to the Services section of the Bombardier
customer portal for the latest prices, rates and fees.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 604−00−002.
MODEL CL−600−2B16
Basic Issue: May 20/2024 604−27−041
Page 2 of 8

### Page 4

2. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection. Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
2 man−hours are necessary to do this modification.
The labour required to do this Service Bulletin is at no cost for the out of warranty
aircraft which have incorporated the SB 604−27−035 within two years.
G. Material − Cost and Availability
No kits or parts are necessary to do this Service Bulletin. For material data, refer to
Paragraph 3.C.
H. Tooling
The equipment and tool listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Stopwatch
NOTES: 1. Refer to the CL−604 Illustrated Tool and Equipment Manual to make
sure you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE
equivalents.
3. This list is provided for a quick reference. In case of discrepancy
between this list and the tool called out in the SPM−MM Chapter 20,
then the tool called in the SPM−MM will prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aviation, Restriction and/or Special Instruction
(RSI), C−4327, Rev. −−.
− Bombardier Aviation, Drawing 604−57140, Rev. C, SNIEO_S24.
− CL−604 Aircraft Maintenance Manual (AMM), Chapters 6, 24 and 27.
MODEL CL−600−2B16
Basic Issue: May 20/2024 604−27−041
Page 3 of 8

### Page 5

L. Other Publications Affected
None.
M. Equivalent Service Bulletins
− For the Challenger 650 aircraft, use SB 650−27−005.
− For the Challenger 605 aircraft, use SB 605−27−012.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the CL−604 Aircraft
Maintenance Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
CL−604 Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
CBP−2 F3 FLAP CONT 2 222
CBP−4 A9 FLAP CONT 1 221
(3) Remove the flight compartment access floor−panel (221 CLF). Refer to
AMM 53−01−01−000−801.
B. Modification
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
Standard SRPSA fees may apply. Refer to the Services section of the
Bombardier customer portal for the latest prices, rates and fees.
(1) Make sure that the flap control lever set to 0.
(2) Gain access to the avionics bay, on the right side, between FS 280.00 and
FS 310.00.
(3) Disconnect connectors P1CE and P9CE from FSOBR/FOBR connectors
J1CE−A and J9CE−A respectively. Refer to Figure 1.
(4) Disconnect FSOBR/FOBR harness connectors P1CE−A and P9CE−A from
connectors J1CE and J9CE respectively at Flight Control Unit (FCU) side, and
move aside FSOBR/FOBR connectors P1CE−A and P9CE−A. Refer to
Figure 1.
MODEL CL−600−2B16
Basic Issue: May 20/2024 604−27−041
Page 4 of 8

### Page 6

(5) Keep the FSOBR/FOBR connectors J1CE−A and J9CE−A on the aircraft
bracket. Refer to Figure 1.
(6) Keep the FSOBR/FOBR connectors P1, P2, P3, P4, terminal block and
terminal lug attached to the FOBR unit, Part No. 604−70201. Refer to Figure 1.
(7) For aircraft serial No. 5588 only, reconnect the FSOBR/FOBR connectors P1,
P2, P3 and P4.
NOTE: FSOBR/FOBR connectors P1, P2, P3 and P4 were cap and stowed
through Drawing 604−57140, SNIEO_S24.
(8) Cap and stow the FSOBR/FOBR harness, Part No. 604−57140−3. Refer to
SPM−MM 20−12−05−02.
(9) Route and reconnect the connectors P1CE and P9CE directly to the FCU
connectors J1CE and J9CE respectively, and tie−wrap (if necessary) to the
surrounding harness. Refer to Figure 2.
C. Testing
(1) Make sure that the flap control lever is at 0.
(2) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
CBP−2 F3 FLAP CONT 2 222
CBP−4 A9 FLAP CONT 1 221
(3) Do the operational test of inboard and outboard flaps. Refer to
AMM 27−54−00−710−801.
D. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Install the flight compartment access floor−panel (221CLF). Refer to
AMM 53−01−01−400−801.
E. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
MODEL CL−600−2B16
Basic Issue: May 20/2024 604−27−041
Page 5 of 8

### Page 7

3. MATERIAL INFORMATION
A. Kits
No kits required.
B. Parts
No parts required.
C. Material
The materials that follow, or equivalent, may be necessary to do this Service
Bulletin. These can be purchased from a local supplier. Bombardier Aviation does
not pay for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Protective Cap − − As Necessary Code: A
Tie−Wrap − − As Necessary Code: A
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Commercially Available
D. Publications
No publications required.
MODEL CL−600−2B16
Basic Issue: May 20/2024 604−27−041
Page 6 of 8

### Page 8

FS280.00
FS295.00
J1CE
J9CE
P1CE
P9CE
P1
P2
P3 P4
TO THE FLAP ONBOARD
RECORDER UNIT
PART NO. 604−70201
J1CE−A
J9CE−A
P1CE−A
J1CE−A
P9CE−A
J9CE−A
FS280.00
SB650−27−005_001
FOBR HARNESS
PART NO. 604−57140−3
TERMINAL
LUG
TERMINAL
BLOCK
3
N 2 0 8 5
TB2086
MODEL CL−600−2B16
Cap and Stow the FSOBR/FOBR Harness
Figure 1
Basic Issue: May 20/2024 604−27−041
Page 7 of 8

### Page 9

SB650−27−005_011
FS280.00
FS295.00
J1CE
P1CE
J9CE
P9CE
MODEL CL−600−2B16
Reconnection of P1CE and P9CE Connectors to Flap Control Unit (FCU)
Figure 2
Basic Issue: May 20/2024 604−27−041
Page 8 of 8

### Page 10

604−27−041 Basic May 20/2024
MODIFICATION – FLAPS – CAP AND STOW THE FLAP SYSTEM
ON−BOARD RECORDER (FSOBR)/FLAP ON−BOARD RECORDER
(FOBR) HARNESS
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 11

SERVICE BULLETIN INCORPORATION SHEET − "604−27−041"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
604−27−041 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
