# Bombardier Service Bulletin 605-22-002

Copy: Revision 01 ("SB 605-22-002 R01"), 19 pages: PDF https://openairdocs.org/files/sha256/db/5d/db5dbba9d81f24373b214612538e15d77b36389d7e8f677e66111145613aa65c; text https://openairdocs.org/service-documents/bombardier/sb-605-22-002/file/db5dbba9d81f.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2017-0626; AD 2018-06-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 605-22-002
- Latest revision known: 605-22-002, Revision 01, dated July 25, 2016 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-605-22-002

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-06-06](https://openairdocs.org/ad/2018-06-06.md), effective Apr 19, 2018: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-605-22-002/proposed.md).

## Text (19 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2017-0626; AD 2018-06-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Basic Issue of this Service Bulletin dated Jun 23/2015 and replace in its
entirety with this Revision 01.
Service Bulletin No. 605−22−002
Date of Basic Issue Jun 23/2015
Revision No. 01 Dated Jul 25/2016
This revision has no effect for aircraft on which the Basic Issue of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as “Not Applicable” for this revision.
This revision is issued to clarify the instructions applicable to each PART. The changes are
as follows:
1. Revise the Service Bulletin Summary Sheet, to add a reference to PART A and PART B
for the man−hours.
2. Revise Paragraph 1, to update the planning information Note 1.
3. Revise Paragraph 1.C., to update the instructions applicable to PART A.
4. Revise Paragraph 1.F., to revise and clarify the man−hours applicable to PART A and
PART B.
5. Revise Paragraph 2.A., to add a reference to PART A for the Special Check and clarify
the instructions.
6. Revise Paragraph 2.B., to add a reference to PART B for the Aircraft Setup.
7. Revise Paragraph 2.F., to update the Recording Statement.
8. Make miscellaneous minor changes, as necessary, with no change of context.
SERVICE BULLETIN
MODEL CL−600−2B16
605−22−002
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

SPECIAL CHECK / MODIFICATION - YAW DAMPER SYSTEM - AUTOMATIC FLIGHT
CONTROL SYSTEM (AFCS) WIRING CHANGE TO PREVENT UN-COMMANDED YAW
DAMPER/LINEAR ACTUATOR MOTION AFTER POWER SUPPLY FAILURE
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Recommended in less than 48 months
from this Service Bulletin release date
(Basic Issue).
EFFECTIVITY: A/C Serial No. 5701 to 5911, 5913 and 5914
MANPOWER: 0.5 man−hour is necessary to do the special check in PART A.
50 man−hours are necessary to do the modification in PART B.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
To place an order for parts or kits, please call Bombardier Aerospace Parts Services
at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
www.cic.bombardier.com
MODEL CL−600−2B16
ATA 22−22
AUTO FLIGHT
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 1 of 1
This Service Bulletin is available at:

### Page 3

SPECIAL CHECK / MODIFICATION - YAW DAMPER SYSTEM - AUTOMATIC FLIGHT
CONTROL SYSTEM (AFCS) WIRING CHANGE TO PREVENT UN-COMMANDED YAW
DAMPER/LINEAR ACTUATOR MOTION AFTER POWER SUPPLY FAILURE
1. PLANNING INFORMATION
NOTES: 1. Consult the log book to verify the part numbers of both Yaw Damper
Linear Actuators. If the part number information is unavailable, refer to the
Accomplishment Instructions in Paragraph 2.A. of this Service Bulletin.
2. Due to the lead−time required for obtaining kits and parts, operators are
advised to order the kits and parts in advance before scheduling the
incorporation of this Service Bulletin. Please contact Parts Services, in
Montreal, for delivery lead times and confirmation of prices.
A. Effectivity
CL−600−2B16 aircraft, Serial No. 5701 to 5911, 5913 and 5914.
The intent of this Service Bulletin was met on aircraft, Serial Nos. 5912, 5915 and
all other subsequent CL−600−2B16 aircraft with the Production Modification
Summary 600−5900, and the Restriction and /or Special Instruction (RSI), C−4098.
NOTES: 1. For these aircraft that have had SVL−4000 YD−LA Part No.
622−9968−102 installed in Production, the Part Interchangeability has
been revised to no longer allow Part No. 622−9968−002 to be
installed on the CL−600−2B16 aircrafts.
2. The instructions given in this Service Bulletin are only applicable to
the systems and parts installed at the time of delivery of the aircraft or
as changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent action
changes to make sure that this bulletin can be completed.
SERVICE BULLETIN
www.cic.bombardier.com
MODEL CL−600−2B16
ATA 22−22
AUTO FLIGHT
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2015−2016 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 1 of 15
This Service Bulletin is available at:

### Page 4

B. Reason
Certain SVL−4000 YD−LA with Part No. 622−9968−002 have an internal −12 VDC
power supply failure mode that can lead to an uncommanded actuator motion.
During the failure mode, the −12 VDC output becomes unstable and randomly
varies between −14 and +1 VDC. Since, the −12 VDC power supply output is tied
to the position feedback circuit and brake/motor control units, this failure can
produce:
− Command Voltage Offset inside the actuator which leads to disengage the
brake of actuator and release the servo motor.
− Position feedback sensor signal error (output from LVDT) which leads to an
erroneous command of actuator position.
This Service Bulletin modifies the wiring connection of Automatic Flight Control
System (AFCS) which will lead to cut off the yaw damper actuator power supply
when the yaw damper DISC switch is pushed. In consequence, the yaw damper
DISC switch will be able to remove the internal un−commanded yaw actuator
motion.
C. Description
This Service Bulletin gives instructions in:
PART A, to:
Do the part number verification for both Yaw Damper Linear Actuators to visually
witness the part number, if the part number of both Yaw Damper Linear Actuators
can not be verified by a log book entry.
− If one or both of the Yaw Damper Linear Actuator installed is Part
No.622−9968−002, proceed to PART B in Paragraph 2.B.
− If the Yaw Damper Linear Actuator Part No. 622−9968−102 is installed in both
positions, proceed to the Close Out in Paragraph 2.E.
PART B, to:
− Get access to Junction Boxes JB14 and JB15,
− Do the wiring modification related to Automatic Flight Control System (AFCS),
and
− Do the necessary operational and functional tests to make sure that the system
operates correctly.
D. Compliance
Recommended in less than 48 months from this Service Bulletin release date
(Basic Issue).
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 2 of 15

### Page 5

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA in
accordance with established procedures.
F. Manpower
NOTES: 1. The man−hours given are estimates to help you schedule the tasks
given in this bulletin. The estimates are for direct labor performed by
an experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower estimates, refer to SB
605−00−002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the labor estimates and should be considered
for planning purposes before you schedule this Service Bulletin.
0.5 man−hour is necessary to do the special check in PART A.
50 man−hours are necessary to do the modification in PART B.
Bombardier Aerospace does not pay the labor to do the special check
(record/visual check) in PART A.
The labor required to do the modification in PART B is at no cost if:
1. the aircraft was under warranty at the time of release of this Service
Bulletin (Basic Issue),
2. the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
3. this Service Bulletin is scheduled in less than 12 months from its
release date (Basic Issue).
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 3 of 15

### Page 6

G. Material − Cost and Availability
Kit 605K22−002 is necessary to do this modification.
KIT NO. PRICE
605K22−002 Please contact Bombardier Aerospace Parts Services in
Montreal, for delivery lead times and confirmation of prices.
Sufficient kits will be kept for the estimated amount of orders.
This kit is available at no cost if a no−charge purchase order is sent to Bombardier
Aerospace in less than 12 months from this Service Bulletin release date (Basic
Issue).
Due to the lead−time for obtaining kits and parts, operators are advised to order the
kits and parts in advance before scheduling the incorporation of this Service
Bulletin. Please contact Parts Services, in Montreal, for delivery lead times and
confirmation of prices.
During or after the above free period, Smart Parts Plus does not pay for the kit.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
24−00−24 S4933959−501 Tag, Circuit Breaker
Refer to the Standard Practices Manual (SPM), Wiring Manual (WM), Chapter 20,
and the table that follows for the tools applicable to the wiring modification:
LUG/
CONTACT
TOOL
CRIMP POSITIONER INSERTION EXTRACTION
M39029/1−101 M22520/1−01 M22520/1−02 M81969/14−11 M81969/14−11
M39029/5−116 M22520/1−01 M22520/1−02 M81969/14−03 M81969/14−03
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 4 of 15

### Page 7

LUG/
CONTACT
TOOL
CRIMP POSITIONER INSERTION EXTRACTION
M39029/
92−534
M22520/1−01 M22520/1−02 M81969/14−03 M81969/14−03
NOTES: 1. Refer to the CL−605 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE
equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Modification Summary, 600−6358, Rev. C.
− Bombardier Aerospace, Modification Summary, 600−5900, Rev. B2.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−4098,
Rev. −−.
− Bombardier Aerospace, Functional Test Engineering Requirements, FTER
604DX−222001, Rev. A.
− Bombardier Aerospace, Kit Drawing K604−70200, Rev. B.
− CL−605 Aircraft Maintenance Manual (AMM), Chapters 12, 22, 24 and 31.
− CL−605 Standard Practices Manual (SPM), Chapter 20.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
For the Challenger 604 aircraft, use SB 604−22−007.
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 5 of 15

### Page 8

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the CL−605 Aircraft
Maintenance Manual unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
CL−605 Aircraft Maintenance Manual, Chapter 6.
A. Part A − Special Check − Yaw Damper Linear Actuators Part Number
Verification
(1) If the part number of both Yaw Damper Linear Actuators can not be verified by
a log book entry, the part number verification must be carried out by physically
accessing both the Yaw Damper Linear Actuators to visually witness the part
number.
(2) To access the Yaw Damper Linear Actuator, refer to
AMM 55−30−43−000−808. If Yaw Damper Linear Actuator Part No.
622−9968−002 is installed,
(a) proceed to Paragraph 2.B., Aircraft Setup.
(b) If Yaw Damper Linear Actuator Part No. 622−9968−102 is installed in both
positions, proceed to Paragraph 2.E., Close Out.
B. Part B − Aircraft Setup
CAUTION: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. YOU CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(3) Remove the external AC power. Refer to AMM 12−00−07−861−802.
(4) Disconnect the auxiliary power unit (APU) battery. Refer to
AMM 24−32−00−040−802.
(5) Remove the Pilot and Copilot seats. Refer to AMM 25−11−01−000−801.
(6) Remove the access panels that follow:
ACCESS DESIGNATION
221EZ Panel, Pilot side Console, Forward
222EZ Panel, Copilot Side Console, Forward
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 6 of 15

### Page 9

CAUTION: OBEY ALL ELECTROSTATIC DISCHARGE-SENSITIVE (ESDS)
PRECAUTIONS. STATIC VOLTAGES CAN CAUSE DAMAGE TO
ESDS COMPONENTS.
(7) Obey all electrostatic discharge−sensitive (ESDS) safety precautions. Refer to
AMM 24−00−00−910−802.
(8) On copilot side console, remove the lamp driver unit (LDU). Refer to
AMM 31−52−01−000−801.
C. Modification
(1) Remove Junction Boxes JB14 and JB15 from the aircraft in order to
accomplish these modifications. For JB14 removal, refer to
AMM 24−01−14−000−801. For JB15 removal, refer to
AMM 24−01−15−000−801.
(2) Do the wiring modification in Junction Boxes JB14 and JB15 as per SPM
Chapter 20. Refer to K604−70200, detail −24, Installation.
NOTE: Make sure JB14 and JB15 are identified post−modification per Kit
Drawing K604−70200, note 3.
(3) Do an electrical continuity check on all wiring introduced or disturbed by this
modification.
(a) Install Ground Studs for Ground Wire installation. Refer to Bombardier
Aerospace, Kit Drawing K604−70200, Rev. B, Flag Note 5.
(4) Install Junction Boxes JB14 and JB15 in the aircraft. For JB14 installation, refer
to AMM 24−01−14−400−801. For JB15 installation, refer to
AMM 24−01−15−400−801 .
(5) Install the lamp driver unit. Refer to AMM 31−52−01−400−801.
(6) Install the access panels that follow:
ACCESS DESIGNATION
221EZ Panel, Pilot side Console, Forward
222EZ Panel, Copilot Side Console, Forward
(7) Install the Pilot and Copilot seats. Refer to AMM 25−11−01−400−801.
D. Testing
(1) Connect and energize the external AC power. Refer to
AMM 12−00−07−861−801.
(2) Connect the auxiliary power unit (APU) battery. Refer to
AMM 24−32−00−440−802.
(3) Do the operational tests given in the table that follows:
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 7 of 15

### Page 10

DESIGNATION TASK
Operational test of the junction box JB14. AMM 24−01−14−710−801
Operational test of the junction box JB15. AMM 24−01−15−710−801
Operational test of the Integrated Avionics
Processor System (IAPS).
AMM 22−12−00−710−801
Do the operational test of the yaw damper
linear actuator.
AMM 22−22−01−710−801
Do the operational test of the yaw damper
control−panel.
AMM 22−22−04−710−801
Do the operational test of the yaw damper
engage buttons.
AMM 22−11−00−710−802
(4) Do the yaw damper engagement test as follows:
(a) Momentarily set the MAINT switch at FS 280L to MFD 2.
(b) Make sure that TO ENTER FCC DIAGNOSTICS page is shown on the
MFD 2.
(c) On the FCP, simultaneously push the right FD button and any two other
mode select buttons to enter FCC DIAGNOSTICS mode.
(d) On the FCP, simultaneously push two mode select buttons until the INPUT
MODE is shown.
(e) On the flight control panel (FCP), turn the pitch wheel until LH RUDPWR
parameter is shown. Make sure that TRUE is shown in the left column on
the MFD 2.
(f) On the basic reversionary control panel set the AFCS SEL switch to 1.
(g) Push the YD 1 on the yaw damper control panel. Push the DISC button to
disengage the yaw damper 1.
(h) Push the YD 2 on the yaw damper control panel. Push the DISC button to
disengage the yaw damper 2.
(i) Engage YD 1. Make sure the EICAS message YD 2 INOP (white) is
shown.
(j) On the flight control panel (FCP), turn the pitch wheel until LH RUDPWR
parameter is shown and, TRUE is shown in the left column on the MFD 2.
(k) Push the DISC button on the yaw damper control panel. Make sure the
EICAS message YAW DAMPER (amber) is shown.
(l) On the flight control panel (FCP), turn the pitch wheel until RH RUDPWR
parameter is shown and, TRUE is shown in the left column on the MFD 2.
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 8 of 15

### Page 11

(m) Engage YD 2. Make sure the EICAS message YD 1 INOP (white) is
shown.
(n) On the flight control panel (FCP), turn the pitch wheel until RH RUDPWR
parameter is shown and, TRUE is shown in the left column on the MFD 2.
(o) Push the DISC button on the yaw damper control panel. Make sure the
EICAS message YAW DAMPER (amber) is shown.
(p) On the basic reversionary control panel set the AFCS SEL switch to 2.
Repeat the steps from (g) to (o) again.
E. Close−out
Remove all tools, equipment and unwanted materials from the aircraft.
F. Recording
You can do each PART of this Service Bulletin independently.  When any PART of
this Service Bulletin is completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
Kit 605K22−002 is necessary to do this Service Bulletin and contains the parts that
follow:
NEW PART NO. QTY ITEM USED
PART NO.
INSTRUCTIONS
- DISPOSITION
B0808005−006N 2 Terminal Lug − −
K604−70200−1/02 1 Wire Kit − −
K604−70200−24/01 1 Wire Kit − −
M12883/47−04 2 Relay Socket − −
M83536/26−002L 2 Relay − −
MS35207−265 2 Screw − −
MS35338−43 4 Lock Washer − −
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 9 of 15

### Page 12

NEW PART NO. QTY ITEM USED
PART NO.
INSTRUCTIONS
- DISPOSITION
MS35650−302 4 Nut − −
NAS1149D0332J 6 Washer − −
NOTES: 1. In case of discrepancy between this list and the ’Service Bulletin Kit
Parts List’ contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
No parts required.
C. Material
No materials required.
D. Publications
No publications required.
MODEL CL−600−2B16
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 10 of 15

### Page 13

K604−70200−B−S −S1−PL 
MODEL CL−600−2B16
PL K604−70200 − Kit − Introduction, AFCS wiring to prevent un−commanded yaw
damper/linear actuator (YD−LA) motion
(Sheet 1 of 3, Rev. B)
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 11 of 15

### Page 14

K604−70200−B−S −S2−PL 
MODEL CL−600−2B16
PL K604−70200 − Kit − Introduction, AFCS wiring to prevent un−commanded yaw
damper/linear actuator (YD−LA) motion
(Sheet 2 of 3, Rev. B)
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 12 of 15

### Page 15

K604−70200−B−S −S3−PL 
MODEL CL−600−2B16
PL K604−70200 − Kit − Introduction, AFCS wiring to prevent un−commanded yaw
damper/linear actuator (YD−LA) motion
(Sheet 3 of 3, Rev. B)
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 13 of 15

### Page 16

K604−70200−B−1 
K604−70200 − Kit − Introduction, AFCS wiring to prevent un−commanded yaw damper/liner
actuator (YD−LA) motion
(Sheet 1 of 1, Rev. B)
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 14 of 15

### Page 17

K604−70200−B−2 
K604−70200 − Kit − Introduction, AFCS wiring to prevent un−commanded yaw damper/liner
actuator (YD−LA) motion
(Sheet 1 of 1, Rev. B, continued)
Basic Issue: Jun 23/2015
Revision 01: Jul 25/2016
605−22−002
Page 15 of 15

### Page 18

605−22−002 Rev. 01 Jul 25/2016
SPECIAL CHECK / MODIFICATION − YAW DAMPER SYSTEM −
AUTOMATIC FLIGHT CONTROL SYSTEM (AFCS) WIRING CHANGE TO
PREVENT UN−COMMANDED YAW DAMPER/LINEAR ACTUATOR
MOTION AFTER POWER SUPPLY FAILURE
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 19

SERVICE BULLETIN INCORPORATION SHEET − "605−22−002"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
605−22−002 01
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
