# Bombardier Service Bulletin 605-57-005

Copy: Revision 01 ("605 57 005 rev01"), 27 pages: PDF https://openairdocs.org/files/sha256/f4/d9/f4d902c633d69619b6c00e80a3e70136de3cb1bae8e5d2aeda62fe7812c49a80; text https://openairdocs.org/service-documents/bombardier/sb-605-57-005/file/f4d902c633d6.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0491; AD 2015-07-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 605-57-005
- Latest revision known: 605-57-005, Revision 01, dated November 12, 2014 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-605-57-005

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-07-02](https://openairdocs.org/ad/2015-07-02.md), effective Jun 4, 2015: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-605-57-005/proposed.md).

## Text (27 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0491; AD 2015-07-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

605-57-005  
 Page 1 of 1 
SERVICE BULLETIN 
REVISION TRANSMITTAL SHEET 
MODEL CL-600-2B16 
Discard the Basic Issue of this Service Bulletin dated Sep 26/2013 and the  
Information Sheet dated Nov 15/2013, and replace in its entirety with this Revision 01.  
 
 
Service Bulletin No. 605-57-005
Date of Basic Issue Se p 26/2013
Revision No. 01 Dated Nov 12 /2014
 
This revision has no effect for aircraft on which the Basic Issue of this  
Service Bulletin was done thus no other action is necessary.  Do not sign the  
log book if you have not done this revision.  Keep the previous log book entry.  
You may make an entry as “Not Applicable” for this revision. 
This revision is issued to separate the procedure into Part A and Part B.  The changes 
are as follows: 
1. Change the Service Bulletin Summary Sheet to update the Manpower and add some 
notes. 
2. Change Paragraph 1, Planning Information, to add the Airworthiness Directive data 
and recommendation for Part A. 
3. Change Paragraph 1.C., Description, to  add Part A, Part B and Testing. 
4. Change Paragraph 1.F., Manpower, to update the man-hours for Part A and Part B. 
5. Change Paragraph 2.A., Aircraft Setup, to update the access specific for Part A and 
Part B. 
6. Change Paragraph 2.B., to update the procedur e specific into Part A and Part B. 
7. Change Paragraph 2.F., to update the Recording instructions. 
8. Change Paragraph 3.B., to split the parts list into Part A and Part B. 
9. Make miscellaneous minor changes, as necessary, with no change of context.

### Page 2

Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 1 of 1 
SERVICE BULLETIN SUMMARY 
This Service Bulletin is available at: 
www.cic.bombardier.com  
MODEL CL-600-2B16 
ATA 57-52  
WINGS 
SPECIAL CHECK  – FLAP HINGE BOX –  
FORWARD LUGS EDGE TO EDGE DISTANCE  
The information below is provided for your reference.  For full details, please 
see corresponding paragraph contained within this bulletin. 
RECOMMENDED
SPECIFIED TIME COMPLIANCE 
COMPLIANCE TIME 
Recommended prior to exceeding  
7,800 flights or within 48 months from 
this Service Bulletin release date  
(Basic Issue), whichever comes first. 
EFFECTIVITY: A/C Serial No. 5701 to 5953 
MANPOWER: 0.5 man-hours to do PART A Special check if done in conjunction with  
SB A605-57-004, PART B. 
18 man-hours to do PART A Special check if not done in conjunction with  
SB A605-57-004, PART B. 
27 man-hours to do PART B, Special Check. 
CONTINUED AIRWORTHINESS (CAW)  
FLEET CAMPAIGN 
YES  NO  
TLMC, CH 5 AFFECTED YES  NO  
KITS and/or PARTS YES  NO  
TOOLING/GSE YES  NO  
PLANNING INFORMATION:  See important 
information at the start of Paragraph 1. YES  NO  
DEDICATED SCHEDULE YES  NO  
PREREQUISITE SERVICE BULLETINS: N/A 
NOTES:  1. To minimize aircraft downtime and cost, it is recommended to do PART A of 
this SB in conjunction with the Alert Service Bulletin A605-57-004, PART B. 
 2. The Basic Issue of this SB605-57-005 is equivalent to PART A and PART B 
of the current revision of this Service Bulletin. 
3. This Service Bulletin is the subject of the Airworthiness Directive  
CF-2014-01 which makes it necessary to implement this Service Bulletin. 
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at: 
514-855-2999 or 1-866-538-1247

### Page 3

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this 
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards. 
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or 
by any means without the prior written consent of Bombardier Inc. and/or its affiliates. 
© 2013 - 2014 Bombardier Inc.  All rights reserved 
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries. 
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 1 of 22 
SERVICE BULLETIN 
This Service Bulletin is available at: 
www.cic.bombardier.com  
MODEL CL-600-2B16 
ATA 57-52  
WINGS 
SPECIAL CHECK  – FLAP HINGE BOX –  
FORWARD LUGS EDGE TO EDGE DISTANCE  
 
1. PLANNING INFORMATION  
NOTES: 1. To minimize aircraft downtime and cost, it is recommended to do PART A 
of this SB in conjunction with the Alert Service Bulletin A605-57-004,  
PART B. 
 2. The Basic Issue of this SB605-57-005 is equivalent to PART A and  
PART B of the current revision of this Service Bulletin. 
3. You can do PART A or PART B of this Service Bulletin independently.   
This Service Bulletin can only be closed and in compliance with  
Transport Canada Airworthiness Directive CF-2014-01, Paragraph D,  
when the special check in PART A and PART B are completed. 
 4. Special tool is required for bushing removal.  See Appendix 2 for details,  
or commercially available tool is acceptable. 
A. Effectivity 
CL-600-2B16 aircraft, Serial No. 5701 to 5953. 
Aircraft, Serial No. 5954 and all other subsequent aircraft are scheduled for 
modification in production (Ref.: Restriction and/or Special Instruction (RSI),  
C-4093). 
NOTE: The instructions given in this Service Bulletin are only applicable to  
the systems and parts installed at the time of delivery of the aircraft  
or as changed by Bombardier Aerospace Service Bulletin(s). 
Before you do this bulletin, examine all STC, STA or equivalent  
action changes to make sure that this bulletin can be completed.

### Page 4

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 2 of 22 
B. Reason 
During production inspection of the flap hinge box assembly, it was found that  
the material around the forward lugs on the inboard and outboard flap hinge boxes 
was below the minimum requirements. 
This Service Bulletin gives instructions to inspect the affected lugs and compare 
them with the limits stated in this Service Bulletin.  If necessary, instructions are 
given if the limits are not met. 
C. Description 
This Service Bulletin gives instructions to: 
– Remove the inboard and/or outboar d forward flap-hinge fairings. 
– PART A, to: 
– Disconnect the wing fitting/lugs of the inboard flap hinge boxes, 
– Measure the forward lugs of the inboard flap hinge boxes, and 
– Reconnect the wing fitting/lugs of the inboard flap hinge boxes. 
– PART B, to: 
– Disconnect the wing fitting/lugs of the outboard flap hinge boxes, 
– Measure the forward lugs of  the outboard flap hinge boxes, and 
– Reconnect the wing fitting/lugs of the outboard flap hinge boxes. 
– Testing, to: 
– Install the inboard and/or outboar d forward flap-hinge fairings, and 
– Do the necessary tests to make sure  that the inboard and outboard flaps operate 
correctly. 
D. Compliance 
Recommended prior to exceeding 7,800 flights or within 48 months from this  
Service Bulletin release date (Basic Issue), whichever comes first. 
E. Approval 
The technical content of this Service Bulletin has been approved under  
the authority of Transport Canada Civil Aviation (TCCA) Design Approval 
Organization (DAO) No. DAO #93-Q-02. 
NOTES: 1. The technical content of this Service Bulletin is accepted by the  
FAA under the Canada/USA bilateral Aviation Safety Agreement. 
2. The technical content of this Service Bulletin is accepted by EASA  
in accordance with established procedures.

### Page 5

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 3 of 22 
F. Manpower 
NOTES: 1. The man-hours given are estimates to help you schedule the tasks  
given in this bulletin.  The estimates are for direct labor performed by  
an experienced crew and do not include the time for familiarization, 
planning, aircraft preparation in hangar such as towing and positioning 
of scaffolds, removal of interior furnishings, repainting, supervision and 
inspection.  
For more information related to the manpower estimates, refer to  
SB 605-00-002. 
2. This Service Bulletin may require consumable materials that have 
specific curing times (refer to Paragraph 3).  The accumulated curing 
time is not included in the labor estimates and should be considered for 
planning purposes before you schedule this Service Bulletin. 
0.5 man-hours are necessary to do PART A, Special Check, if done in conjunction  
with SB A605-57-004, Part B (not claimable). 
18 man-hours are necessary to do PART A, Special Check if SB A605-57-004,  
PART B does not apply. 
27 man-hours are necessary to do PART B, Special Check. 
27 man-hours to do PART B of this Service Bulletin are at no cost for aircraft, Serial 
numbers 5701 to 5920 in new aircraft warranty at the time of release of this Service 
Bulletin (Basic Issue), 
(i) the work is done at Bombardier Business Aviation Services (BBAS) or 
Authorized Service Facilities (ASF), and  
(ii) this Service Bulletin is scheduled pr ior to exceeding 7,800 flights or within 
48 months from this Service Bulletin release date (Basic Issue), whichever 
comes first. 
and 
18 man-hours to do PART A of this Service Bulletin are at no cost for aircraft,  
Serial numbers 5701 to 5920 in new aircraft warranty at time of release of this  
Service Bulletin (Basic Issue), if the aircraft has signed PART C and not 
incorporated PART B of SB A605-57-004, and if: 
(iii) the work is done at Bombardier Business Aviation Services (BBAS) or 
Authorized Service Facilities (ASF), and  
(iv) this Service Bulletin is scheduled pr ior to exceeding 7,800 flights or within 
48 months from this Service Bulletin release date (Basic Issue), whichever 
comes first.

### Page 6

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 4 of 22 
Or 
45 man-hours to do PART A and PART B of this Service Bulletin are at no cost for 
aircraft, Serial numbers 5921 to 5953 in new aircraft warranty at the time of release 
of this Service Bulletin (Basic Issue) and if: 
(i)  the work is done at Bombardier Business Aviation Services (BBAS) or 
Authorized Service Facilities (ASF), and  
(ii) this Service Bulletin is scheduled pr ior to exceeding 7,800 flights or within 
48 months from this Service Bulletin release date (Basic Issue), whichever 
comes first. 
G. Material - Cost and Availability 
The parts listed in Paragraphs 3.B. may be necessary to do this modification. 
If necessary, the parts are available at no cost for aircraft in new aircraft warranty  
at the time of release of this Service Bulletin (Basic Issue), if: 
(i) a no-charge purchase order is sent to Bombardier Aerospace prior to 
exceeding 7,800 flights or within 48 months, whichever comes first, from this 
Service Bulletin release date (Basic Issue).   
During or after the above free period, Smart Parts Plus does not pay for the parts. 
H. Tooling 
The equipment and tools listed below are necessary to do this Special Check:  
GSE REFERENCE NO. PART NO. DESCRIPTION 
24-00-24 - Tag, Circuit Breaker 
Commercially Available - Torque Wrench 20 to 25 lbf in (2.26 to 2.82 Nm) 
Commercially Available - Torque Wrench 30 to 35 lbf in (3.39 to 3.95 Nm) 
Commercially Available - C-Clamp 
The tool listed below or a commercially available equivalent tool is required for the 
removal of the bushings. 
REFERENCE NO. PART NO. DESCRIPTION 
See Note 3 - Support Block 
NOTES: 1. Refer to the CL-605 Illustrat ed Tool and Equipment Manual (ITEM)  
to make sure that you use the correct equipment configuration. 
2. Refer to the Liability Statement  in the ITEM for acceptable GSE 
equivalents. 
3. For the support block manufacturing details, refer to Appendix 2.

### Page 7

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 5 of 22 
I. Weight and Balance 
No change. 
J. Electrical Load Data 
No change. 
K. References 
– Bombardier Aerospace, Restriction and/or Special Instruction (RSI),  
C-4093, Rev. A2. 
– CL-605 Aircraft Illustrated Part s Catalog (AIPC), Chapter 57. 
– CL-605 Aircraft Illustrated Tool  and Equipment Manual, Chapter 24. 
– CL-605 Aircraft Maintenance Manual (AMM), Chapters 6, 12, 27, and 57. 
– CL-605 Standard Practice M anual (SPM), Chapter 51. 
– CL-605 Standard Practice M anual (SRM), Chapter 51. 
– CL-605 Time Limits and Maintenance Checks (TLMC), Chapter 5. 
– Bombardier Aerospace, Modifica tion Summary IS600-57-0001, Rev. A. 
– Appendix 1 – Information Feedback Sheet (attached). 
– Appendix 2 – Support Block (attached). 
L. Other Publications Affected 
– None. 
M. Equivalent Service Bulletins 
– For the Challenger 600 aircraft, use SB 600-0762. 
– For the Challenger 601 aircraft, use SB 601-0631. 
– For the Challenger 604 aircraft, use SB 604-57-007. 
2. ACCOMPLISHMENT INSTRUCTIONS 
NOTES: 1. All TASKs given in the procedures  that follow are from the Aircraft 
Maintenance Manual unless otherwise specified. 
2. All references made to zones, a ccess panels and/or doors, are from  
the Aircraft Maintenance Manual, Chapter 6 
3. The Basic Issue of this SB605-57-005 is equivalent to PART A and  
PART B of the current revision of this Service Bulletin. 
A. Aircraft Setup 
(1) Install the safety devices and the warning signs in the applicable locations and 
the warning placard on the flap control lever. 
(2) Obey all electrical/electronic safety  precautions. Refer to TASK 24-00-00-910-801. 
(3) Connect and energize the exter nal AC power.  Refer to  
TASK 12-00-07-861-801.

### Page 8

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 6 of 22 
(4) Set the flap control lever to 45 degrees and make sure that the flaps are fully 
extended. 
(5) Remove the external AC power.  Refer to TASK 12-00-07-861-802. 
(6) Open and tag the circuit breakers that follow: 
CB PANEL CB NO. NAME ZONE 
CBP-2 B5 FLAP MOTOR 2 222 
CBP-2 F3 FLAP CONT 2 222 
CBP-3 B11 FLAP MOTOR 1 221 
CBP-4 A9 FLAP CONT 1 222 
(7) For PART A, remove fillet sealant from perimeter around the forward inboard 
flap hinge-fairings, making contact with the wing surface and the inboard flap 
respectively.  Refer to SPM-MM 51-23-00-100-801. 
Remove the left and right inboard flap hinge-fairings that follow:  Refer to  
TASK 57-26-03-000-801. 
ACCESS DESIGNATION 
571AB (671AB) Fairing, Forward Inboard – Flap Hinge 
571EB (671EB) Fairing, Forward Inboard – Flap Hinge 
(8) For PART B, remove fillet sealant from perimeter around the forward outboard 
flap hinge-fairings, making contact with the wing surface and the outboard flap 
respectively.  Refer to SPM-MM 51-23-00-100-801. 
Remove the left and right outboard forward flap hinge-fairings that follow:  Refer 
to TASK 57-26-05-000-801. 
ACCESS DESIGNATION 
581BB (681BB) Fairing, Forward Outboard 
581DB (681DB)  Fairing, Forward Outboard 
581FB (681FB) Fairing, Forward Outboard

### Page 9

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 7 of 22 
B. PART A:  Measurement of the Inboa rd Forward-Lug Edge to Edge Distance  
of the Flap-Hinge-Boxes, Part No. 600-10116, 600-10117. 
CAUTION: ONLY ONE FLAP HINGE BOX IS TO BE DISCONNECTED AND 
INSPECTED AT A TIME.  THE FLAP HINGE BOX MUST BE 
SUPPORTED DURING THE INSPECTION SO AS NOT TO  
DAMAGE THE FLAPS AND ATTACHED COMPONENTS. 
(1) For each wing, disconnect one flap hinge box at a time  from the wing 
forward-attachment fitting and wing aft-attachment fitting. 
NOTES: 1. The flap will be supported by the other attached flap hinge box/arm 
and both actuators. 
 2.  To reduce the load on the other attached flap hinge box/arm  
and actuators, the flaps should also be supported per best  
shop practice or with a bench and padding.  Refer to Figure 1. 
 
Figure 1 
(2) Disconnect the inboard flap hinge box (1 ) at location WS 76.50 and WS 127.25  
as follows:  Refer to Figures 1, 2, 3 and 4. 
NOTE: It is not necessary to remove the flap hinge boxes from the aircraft for 
the lug edge to edge distance measurement.  Refer to Figure 2 for the 
recommendations to disconnect the flap hinge box.

### Page 10

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 8 of 22 
 
 
 
 
 
 
 
 
 
Flap Hinge Box 
Figure 2 
(a) If necessary, remove and keep the hardware that attach the bonding 
jumpers to the flap hinge box (1). 
(b) For the flap hinge box (1) located at WS 76.50 only, do as follows: 
(i) If necessary, disconnect the electrical connector wire (3) from any 
attached location on the structure, to allow downward movement of 
the flap hinge box. 
WARNING: WEAR EYE PROTECTION WHEN YOU CUT THE COTTER 
PIN.  WHEN THE COTTER PIN IS CUT,  
PIECES CAN HIT YOUR  EYES AND CAUSE INJURIES. 
(ii) Remove and discard the cotter pin (4).  Refer to  
SPM-MM 20-50-00-000-802. 
Support for the 
flap hinge box 
Disconnect  
flap hinge box 
from fittings. CAUTION: 
Make sure that there is no 
contact between the flap hinge 
box and fairing to avoid 
damage when lowering the 
flap hinge box. 
If required, remove  
flap hinge box 
bonding jumper. 
Lower flap hinge box 
enough to permit 
measurement of the 
lug edge to edge 
distance.

### Page 11

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 9 of 22 
(iii) Remove the nut (5), washer (6) and bolt (7) and disconnect the  
control rod (2) from the lever (8) of the flap position transmitter. 
(iv) If disconnected, put protective covers on the open ends of the 
electrical connector (3) and on the electrical connection of the  
position transmitter. 
(c) Remove and keep the nuts (9), washers (10) and (11), bolts (12), to 
disconnect the flap hinge box (1) from the forward attachment fitting. 
                       
  
 
CAUTION: TO REMOVE AND INSTALL THE HINGE 
BUSHINGS USE A C-CLAMP METHOD WITH  
THE SUPPORT BLOCK.  USE LIGHT  ANTI-SEIZE 
LUBRICANT (LPS-1 OR SIMILAR) IF THE 
BUSHINGS ARE SEIZED OR DIFFICULT TO 
REMOVE, MAKE SURE THAT THE LATERAL 
FORCE DOES NOT EXCEED 200 LBS AND DO 
NOT USE A HAMMER TO REMOVE THE 
BUSHINGS, THIS CAN CAUSE DAMAGE. 
 BEFORE YOU INSTALL THE C-CLAMP, MAKE 
SURE YOU INSTALL A SUPPORT BLOCK 
BETWEEN THE FITTINGS, SHIMS IN ALL GAPS 
AS REQUIRED TO AVOID BENDING AND 
DAMAGE FROM THE CLAMP FORCE. 
 OTHER METHOD THAN C-CLAMP COULD BE 
USED, PROVIDED LUGS ARE SUPPORTED AND 
LATERAL FORCE DOES NOT EXCEED 200 LBS 
TO AVOID DAMAGE. 
Figure 3 
Install the support block, 
manufactured as per 
Appendix 2 or an 
equivalent commercially 
available tool between 
the fittings. 
Shim all gaps as 
required.

### Page 12

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 10 of 22 
(d) Remove bushings (13) to disconnect the flap hinge box (1) from the forward 
attachment fitting.  Keep bushings (13) if not damaged to  
re-install later.  Refer to Figures 3 and 4. 
CAUTION: HOLD THE FLAP HINGE BOX WHILE THE BOLTS ARE 
REMOVED.  IF THE FLAP HINGE BOX FALLS, IT WILL  
CAUSE DAMAGE TO THE FLAP HINGE BOX AND ATTACHED 
COMPONENTS. 
(e) Remove and keep the nuts (14), was hers (15) and (16), and bolts (17),  
to disconnect the hinge box (1) from the aft attachment fitting. 
(f) Remove bushings (18) to disc onnect the hinge box (1) from the aft 
attachment fitting.  Keep bushings (18) if not damaged to re-install later.  
Refer to Figures 3 and 4. 
CAUTION: MAKE SURE THERE IS NO CONTACT BETWEEN THE FLAP  
HINGE BOX AND AFT FAIRING TO AVOID DAMAGE TO THE 
AIRCRAFT STRUCTURE WHEN YOU LOWER THE FLAP HINGE BOX 
DOWNWARD FOR ACCESS. 
(3) Carefully pull the flap hinge box (1) dow nward to allow access to the forward 
lugs for the lug edge to edge distance measurement.

### Page 13 (OCR)

CHÄLLENGÉR 605
MODEL CL-600-2B16
FLAP
POSITION
TRANSMITTER  SUPPORT
CAUTION: ONLY ONE FLAP HINGE BOX IS TO BE
DISCONNECTED AT A TIME. THE FLAP
HINGE BOX MUST BE SUPPORTED
DURING THE MODIFICATION SO AS NOT
TO DAMAGE THE FLAPS AND ATTACHED
COMPONENTS.
AFTACHMENT FITTING
FORWARD
ATTACHMENT FITTING  16
AREA OF INSPECTION
O oK
Inboard Flap-Hinge-Box
Figure 4
Basic Issue: Sep 26/2013  605-57-005
Revision 01: Nov 12/2014  Page 11 of 22

### Page 14

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 12 of 22 
(4) Measure and record the minimum edge to edge distance of the forward  
lugs of the inboard flap hinge boxes at locations WS 76.50 and WS 127.25.   
Refer to Figure 5. 
 
NOTE: LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE. 
 
WS 76.50 and WS 127.25 
Inboard Flap-Hinge-Box Forward-Lug Edge to Edge Distance Limits 
Figure 5

### Page 15

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 13 of 22 
(5) If any of the inboard flap-hinge-box forw ard lug edge to edge distance is below 
the 0.256 in (6.50 mm) minimum limit do the steps that follow: 
(a) Fill-in Appendix 1 with the data (minimum edge to edge distance, hole 
diameter, lug thickness & lug location) applicable to the faulty Flap Hinge 
Box(es), then, 
(b) Submit Appendix 1 with an SRPSA to Customer Support Engineering 
(CSE) for evaluation and an approved repair by e-mail at: 
SRPSA@aero.bombardier.com. 
(6) If the measured forward-lug edge to edge distance of the inboard flap-hinge-
boxes are equal or above the minimum limit, no corrective action is required.  
Install the inboard flap-hinge-box in the steps that follow. 
(7) Install the inboard flap hinge box (1) at locations WS 76.50 and WS 127.25  
as follows:  Refer to Figure 4. 
(a) Apply a layer of Mastinox 6856K to the bushings (13) and (18) on 
installation. 
(b) Put the flap-hinge-box (1) in position. 
(c) Install bushings (18) on the flap hinge box (1) and aft attachment fitting. 
(d) Install bushings (13) on the forward lugs of the flap hinge box (1) and 
forward attachment fitting. 
(e) Install bolts (17), washers (15) and (16), and nuts (14) to attach the flap 
hinge box (1) to the aft attachment fitting. 
NOTE: Make sure the sum of the gap measurement between the aft 
attachment fitting and lower surface of bolt head (17), and 
between the aft attachment fitting and the lower surface of 
washer (15), is 0.020 in to 0.105 in (0.508 mm to 2.667 mm). 
Refer to TASK 57-52-01-400-801. 
(f) Install the bolts (12), washers (10)  and (11), and nuts (9) to attach the flap 
hinge box (1) to the forward attachment fitting. 
NOTE: Make sure the sum of the gap measurement between the 
forward attachment fitting and lower surface of bolt head (12), 
and between the forward attachment fitting and the lower surface 
of washer (10), is 0.015 in to 0.060 in (0.381mm to 1.524 mm).  
Refer to TASK 57-52-01-400-801. 
(g) Torque the nuts (9), and (14) from 30 to 35 lbf in (3.39 to 3.95 Nm).   
Refer to SPM-MM 20-21-00-910-801. 
(h) Attach the control rod (2) and electr ical connector (3) to the flap position 
transmitter as follows: 
(i) Align the eye of the control rod (2) with the lever (8). 
(ii) Install the bolt (7), washer (6) and the nut (5). 
(iii) Torque the nut (5), from 20 to 25 lbf in (2.26 to 2.82 Nm).  Refer to 
SPM-MM 20-21-00-910-801.

### Page 16

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 14 of 22 
WARNING: WEAR EYE PROTECTION WHEN YOU CUT THE COTTER 
PIN.  WHEN THE COTTER PIN IS CUT,  
PIECES CAN HIT YOUR  EYES AND CAUSE INJURIES. 
(iv) Install the cotter pin (4).  Refer to SPM-MM 20-50-00-400-802. 
(v) Remove the protective covers from the open ends of the electrical 
connector (3) and from the electrical connection of the position 
transmitter. 
(vi) If disconnected, connect the electrical connector (3) to the flap position 
transmitter. 
NOTE: If detached, attach the electrical connector wire to the 
necessary locations on the structure. 
(i) If removed, install the bonding jumper on the flap hinge box (1).  Refer to  
SPM 51-80-00-400-801. 
(j) If necessary, do the electrical bonding test for the applicable flap hinge box 
(1).  Refer to SPM-MM 51-80-00-760-801. 
C. PART B:  Measurement of the Outboard Forward-Lug Edge to Edge Distance 
of the Flap-Hinge-Boxes, Part No. 600-10118, 600-10119, and 600-10120. 
(1) Disconnect the outboard flap hinge box (19) at locations WS 178.00,  
WS 220.00, and WS 264.00 as follows:  Refer to Figures 1, 2, 3 and 6. 
NOTE: It is not necessary to remove the flap hinge boxes from the aircraft for 
the lug edge to edge distance measurement.  Refer to Figure 2 for the 
recommendations to disconnect the flap hinge box. 
(a) If necessary, remove and keep the hardware that attach the bonding 
jumpers to the flap hinge box (19). 
(b) Disconnect the control rod (23) from t he BUTE door fitting in the steps that 
follow: 
WARNING: WEAR EYE PROTECTION WHEN YOU CUT THE  
COTTER PIN.  WHEN THE COTTER PIN IS CUT,  
PIECES CAN HIT YOUR  EYES AND CAUSE INJURIES. 
(i) Remove and discard the cotter pin (20).  Refer to  
SPM-MM 20-50-00-000-802. 
(ii) Remove and keep the pin (21) and washer (22) to disconnect the 
control rod (23) from the BUTE door fitting. 
(c) Remove and keep the nuts (24), was hers (25) and (26), and bolts (27),  
to disconnect the hinge box (19) from the forward attachment fitting. 
(d) Remove bushings (28), to disconnect the hinge box (19) from the forward 
attachment fitting.  Keep bushings if not damaged to re-install later.  Refer 
to Figures 3 and 6.

### Page 17

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 15 of 22 
CAUTION: HOLD THE FLAP HINGE BOX WHILE THE BOLTS ARE 
REMOVED.  IF THE FLAP HINGE BOX FALLS, IT WILL  
CAUSE DAMAGE TO THE FLAP HINGE BOX AND ATTACHED 
COMPONENTS. 
(e) Remove and keep the nuts (29), was hers (30) and (31), and bolts (32),  
to disconnect the hinge box (19) from the aft attachment fitting. 
(f) Remove bushings (33), to disconnect the hinge box (19) from the aft 
attachment fitting.  Keep bushings if not damaged to re-install later.   
Refer to Figures 3 and 6. 
CAUTION: MAKE SURE THERE IS SUFFICIENT CLEARANCE BETWEEN  
THE FLAP HINGE BOX AND AFT FAIRING TO AVOID DAMAGE  
TO THE AIRCRAFT STRUCTURE WHEN YOU LOWER THE FLAP  
HINGE BOX DOWNWARD FOR ACCESS. 
(2) Carefully pull the flap hinge box (19) downward to allow access to the forward 
lugs for the lug edge to edge inspection.

### Page 18

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 16 of 22 
19
24
27
19
29
30
33
31
32
DSB57050_004
FORWARD ATTACHMENT
FITTTING AFT ATTACHMENT
FITTTING
AREA OF
INSPECTION
25
28
26
27
22
21
20
23
FITTING BUTE DOOR
 
Outboard Flap-Hinge-Box 
Figure 6

### Page 19

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 17 of 22 
(3) Measure and record the minimum lug edge to edge distance of the forward  
lugs of the outboard flap hinge boxes at location WS 178.00, WS 220.00, and  
WS 264.00.  Refer to Figure 7. 
 
NOTE: LEFT SIDE SHOWN, RIGHT SIDE OPPOSITE. 
 
WS 178.00, WS 230.00 and WS 264.00 
Outboard Flap-Hinge-Box Forward-Lug Edge to Edge Distance Limits 
Figure 7

### Page 20

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 18 of 22 
(4) If any of the outboard flap-hinge-box  forward-lug edge to edge distance is 
below the 0.182 in (4.62 mm) minimum limit do the steps that follow: 
(a) Fill-in Appendix 1 with the data (minimum edge to edge distance, hole 
diameter, lug thickness & lug location) applicable to the faulty Flap Hinge 
Box(es), then, 
(b) Submit Appendix 1 with an SRPSA to  Customer Support Engineering 
(CSE) for evaluation and an approved repair by e-mail at: 
SRPSA@aero.bombardier.com. 
(5) If the measured forward-lug edge to edge distance of the outboard flap-hinge-
boxes are equal or above the minimum limit, no corrective action is required.  
Follow the next steps to install the outboard flap hinge box. 
(6) Install the outboard flap hinge box (19) at locations WS 178.00, WS 220.00,  
and WS 264.00 as follows:  Refer to Figure 6. 
(a) Apply a layer of Mastinox 6856K to the bushings (28) and (33) on 
installation. 
(b) Put the flap-hinge-box (19) in position. 
(c) Install the bushings (33) on the flap hinge box (1) and aft attachment fitting. 
(d) Install the bushings (28) on the fo rward lugs of the flap hinge box (1)  
and forward attachment fitting. 
(e) Install bolts (32), washers (30) and (31), and nuts (29) to attach the  
flap hinge box (19) to the aft attachment fitting. 
NOTE: Make sure the sum of the gap measurement between the aft 
attachment fitting and lower surface of bolt head (32), and 
between the aft attachment fitting and the lower surface of 
washer (30), is 0.020 in to 0.105 in (0.508 mm to 2.667 mm). 
Refer to TASK 57-52-01-400-801. 
(f) Install the bolts (27), washers ( 25) and (26), and nuts (24) to attach  
the flap hinge box (19) to the forward attachment fitting. 
NOTE: Make sure the sum of the gap measurement between the forward 
attachment fitting and lower surface of bolt head (27), and between 
the forward attachment fitting and the lower surface of washer 
(25), is 0.015 in to 0.060 in (0.381mm to 1.524 mm).  
Refer to TASK 57-52-01-400-801. 
(g) Torque the nuts (24) and (29) from 30 to  35 lbf in (3.39 to 3.95 Nm).  Refer 
to SPM-MM 20-21-00-910-801. 
(7) Connect the control rod (23) to the BUTE  door fitting in the steps that follow:  
Refer to Figure 6. 
(i) Put the control rod (23) in position on the BUTE door fitting. 
(ii) Install the pin (21) and washer ( 22) to connect the control rod (23) to 
the BUTE door fitting.

### Page 21

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 19 of 22 
WARNING: WEAR EYE PROTECTION WHEN YOU CUT THE COTTER 
PIN.  WHEN THE COTTER PIN IS CUT,  
PIECES CAN HIT YOUR  EYES AND CAUSE INJURIES. 
(iii) Safety the pin (21) with the new cotter pin (20).  Refer to  
SPM-MM 20-50-00-000-802. 
(8) If removed, install the bonding jumper s on the outboard flap hinge box (19).  
Refer to SPM 51-80-00-400-801. 
(9) If necessary, do the electrical bonding test  for the applicable flap hinge box (19).   
Refer to SPM-MM 51-80-00-760-801. 
D. Testing 
(1) Do an operational test of the inboard and outboard flaps to make sure the  
flap hinge box assemblies move freely, before installing the flap hinge-fairings.   
Refer to TASK 27-54-00-710-801. 
(2) Install the left and right inboard flap hi nge-fairings that follow:  Refer to  
TASK 57-26-03-400-801. 
ACCESS DESIGNATION 
571AB (671AB) Fairing, Forward Inboard – Flap Hinge 
571EB (671EB) Fairing, Forward Inboard – Flap Hinge 
(3) If removed, install the left and right out board flap hinge-fairings that follow:  
Refer to TASK 57-26-05-400-801. 
ACCESS DESIGNATION 
581BB (681BB) Fairing, Forward Outboard 
581DB (681DB)  Fairing, Forward Outboard 
581FB (681FB) Fairing, Forward Outboard 
(4) Apply a filet of sealant around the flap hinge fairings.  Refer to  
SPM-MM 51-23-00-390-805. 
(5) Remove the tags and close the circuit breakers that follow: 
CB PANEL CB NO. NAME ZONE 
CBP-2 B5 FLAP MOTOR 2 222 
CBP-2 F3 FLAP CONT 2 222 
CBP-3 B11 FLAP MOTOR 1 221 
CBP-4 A9 FLAP CONT 1 222 
(6) Connect and energize the exter nal AC power.  Refer to  
TASK 12-00-07-861-802.

### Page 22

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 20 of 22 
(7) Set the flap control lever to 0 and ma ke sure that the flaps retract fully. 
(8) Do an operational test of the inboard and outboard flaps.  Refer to  
TASK 27-54-00-710-801. 
(9) Remove the external AC power.  Refer to TASK 12-00-07-861-802. 
E. Close-out 
Remove all tools, equipment and unwanted materials from the aircraft. 
F. Recording 
You can do PART A or PART B of this Service Bulletin independently. 
When any PART of this Service Bulletin is completed, make an entry in the aircraft 
log and send the attached Incorporation Notice to Bombardier Business Aircraft 
Customer Services (BBACS). 
This Service Bulletin can only be closed and in compliance with  
Transport Canada Airworthiness Directive CF-2014-01, Paragraph D, when the 
special check in PART A and PART B is completed. 
In an effort to improve the quality of our technical communications, we are 
requesting your feedback.  Please take a moment to fill out our easy on-line Service 
Bulletin survey: 
http://csefeedback.aero.bombardier.com

### Page 23

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 21 of 22 
3. MATERIAL INFORMATION 
A. Kit 
No kit required. 
B. Parts 
The parts that follow are necessary to do PART A of this Service Bulletin and are 
available from Bombardier Aerospace Parts Services, Montreal: 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS - 
DISPOSITION 
MS24665-71 2 Cotter Pin - - 
The parts that follow are necessary to do PART B of this Service Bulletin and are 
available from Bombardier Aerospace Parts Services, Montreal: 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS - 
DISPOSITION 
MS24665-151 6 Cotter Pin - - 
The parts that follow may be necessary, to do PART A of this Service Bulletin if the 
removed bushing(s) are damaged or found corroded: 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS - 
DISPOSITION 
600-10300-609 0 - 8 Sleeve Bushing - - 
600-10300-611 0 - 8 Sleeve Bushing - - 
The parts that follow may be necessary to do PART B of this Service Bulletin if the 
removed bushing(s) are damaged or found corroded: 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS - 
DISPOSITION 
600-10300-613 0 - 12 Sleeve Bushing - - 
600-10300-615 0 - 12 Sleeve Bushing - -

### Page 24

MODEL CL-600-2B16  
Basic Issue: Sep 26/2013 605-57-005 
Revision 01: Nov 12/2014 Page 22 of 22 
 
C. Material 
The materials that follow, or equivalent, are necessary to do this Service Bulletin.   
These can be purchased from a local supplier.  Bombardier Aerospace does not  
pay for these consumables. 
DESCRIPTION PART 
No./NAME 
SPECIFICATION QUANTITY SUPPLIER
(See Note)
Compound, 
Sealing 
CT: 2 Hours or 
30 Minutes 
- MIL-S-81733 
Type II, PS 870 
Class B-2 or  
B-1/2 
As 
Necessary 
Code: A 
Compound, 
Corrosion 
Inhibitor 
- Mastinox 6856K As 
Necessary 
Code: A 
NOTES: 1. Refer to the table that follows for each supplier’s address listed by 
codes. 
2. The Curing Time (CT), if applicable, for each consumable material is 
indicated with the description of each product. 
3. At time of release of this Service Bulletin, the information on the 
supplier was valid and accurate.  In the event that this information has 
changed, the operator is encouraged to use the World Wide Web to 
find a local supplier. 
SUPPLIERS ADDRESSES BY CODES 
Code: A 
PRC – Desoto International 
5430 San Fernando Road,  
PO Box 1800, Glendale,  
CA, U.S.A. 91209 
Tel.: 1-800-228-5635  
Fax: (818)-549-7790 
Web Site: www.ppg.com/prc-desoto 
D. Publications 
No publications required.

### Page 25

SERVICE BULLETIN EVALUATION FORM 
(Your ideas will help us provide better bulletins) 
SERVICE BULLETIN: 605-57-005 ISSUE: Rev. 01 DATED: Nov 12/2014 
      
TITLE: Special Check  – Flap Hinge Box – Forward Lugs Edge to Edge Distance  
 
 
 
 
 
 
 
In an effort to improve the quality of our technical communications, we are replacing 
the standard Service Bulletin Evaluation Form with an on-line Service Bulletin 
Survey and we are requesting your feedback.  Please take a moment to fill out our 
easy on-line Service Bulletin survey:   
 
 
 
 
 
http://csefeedback.aero.bombardier.com

### Page 26

SERVICE BULLETIN INCORPORATION SHEET – “605-57-005” 
 
BOMBARDIER 
SUBMISSION Upon completion of the Service Bulletin, please fill-in, fax to 
(514) 855-8798 or e-mail to Fracas at fracas.montreal@aero.bombardier.com 
 
If your aircraft is registered on CAMP and you are reporting to them, 
please do not send the incorporation sheet to Bombardier. If your aircraft 
is on another tracking system, please contact Bombardier to make 
arrangements for automated data submission. 
 
 
           COMPLIED WITH  
 Service Bulletin 
Number 
 Rev.  * Parts 
Completed 
YES NO N/A Remarks/Reason 
 605-57-005  01  PART A     
 “  “  PART B     
 -  -  -     
 
 Actual hours to accomplish Service Bulletin:    
 
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, 
C, D, etc.) which can be carried out separately, indicate only those parts 
completed at this time. 
2. For repetitive checks (usually PART A) only the initial check should be reported 
unless otherwise stated in the Service Bulletin. 
* NOTES:  
 
 
  
  3. When more than one part is carried out at the same time, each part should be 
reported. 
 
 Aircraft Serial No.   Aircraft Reg. No.   
 Airframe Hours:   Airframe Landings   
 S.B. Incorporation date   Service Order No.   
  (dd/mm/yy)    
 Facility Incorporating S.B.  
 Name  Signature  Date  
                               (dd/mm/yy) Signature not required if sent by E-Mail

### Page 27

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --  
 
 
 
 
 
Bombardier Business Aircraft Customer Services (BBACS) 
P.O. Box 6087, Station Centre-ville 
Montreal, Québec, Canada H3C 3G9 
 
Attention: Customer Support Department, Maintenance Engineering 
 
 
 
 
 
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
