# Bombardier Service Bulletin 650-32-004

Copy: No revision named ("650-32-004"), 17 pages: PDF https://openairdocs.org/files/sha256/50/1c/501c22fb0a6cc56be13682fe83f51dc5fea432c6a85e69b1102640b5ff9b4f88; text https://openairdocs.org/service-documents/bombardier/sb-650-32-004/file/501c22fb0a6c.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0462; AD 2021-20-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 650-32-004
- Page: https://openairdocs.org/service-documents/bombardier/sb-650-32-004

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-03-06](https://openairdocs.org/ad/2024-03-06.md), effective Apr 16, 2024: No revision named
- [AD 2021-20-13](https://openairdocs.org/ad/2021-20-13.md), effective Nov 18, 2021: No revision named

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/bombardier/sb-650-32-004/proposed.md).

## Text (17 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0462; AD 2021-20-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Jan 05/2021 650-32-004Page 1 of 1
SERVICE BULLETIN INFORMATION SHEET
MODEL CL-600-2B16
ATA 32−32
LANDING GEAR
SPECIAL CHECK - MAIN LANDING GEAR - LUBRICATION AND INSPECTION OF
LH/RH MAIN LANDING GEAR (MLG) SHOCK STRUT LOWER PIN 19146-3
Service Bulletin No.: 650-32-004 Issue: Basic Dated: Jun 30/2020
The following data is supplied for information only.  No revision to the Service Bulletin
is necessary.
Keep this Information Sheet and Information Sheet dated Jul 30/2020 with subject
Service Bulletin.
This Information Sheet is issued to inform operators that the TCCA Airworthiness
Directive, CF-2020-54R1 is now attached to this Service Bulletin.
The reference in Paragraph 1.K. is updated to read as follows:
1.K. References
−  TCCA Airworthiness Directive, CF-2020-54R1 (attached).

### Page 2

Jul 30/2020 650-32-004Page 1 of 1
SERVICE BULLETIN INFORMATION SHEET
MODEL CL-600-2B16
ATA 32−32
LANDING GEAR
SPECIAL CHECK - MAIN LANDING GEAR - LUBRICATION AND INSPECTION OF
LH/RH MAIN LANDING GEAR (MLG) SHOCK STRUT LOWER PIN 19146-3
Service Bulletin No.: 650-32-004 Issue: Basic Dated: Jun 30/2020
The following data is supplied for information only.  No revision to the Service Bulletin
is necessary.
Keep this Information Sheet with subject Service Bulletin.
This Information Sheet is issued to inform operators that the Safran Landing Systems
Service Bulletin SB19090−32−9 is now attached to this Service Bulletin.
The reference in Paragraph 1.K. is updated to read as follows:
1.K. References
−  Safran Landing Systems, Service Bulletin SB19090 −32−9 (attached).

### Page 3

SPECIAL CHECK – MAIN LANDING GEAR – LUBRICATION AND INSPECTION OF
LH/RH MAIN LANDING GEAR (MLG) SHOCK STRUT LOWER PIN 19146-3
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No 6050 to 6999
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL CL−600−2B16
ATA 32−32
LANDING GEAR
Basic Issue: Jun 30/2020 650−32−004
Page 1 of 1
This Service Bulletin is available at:

### Page 4

SPECIAL CHECK – MAIN LANDING GEAR – LUBRICATION AND INSPECTION OF
LH/RH MAIN LANDING GEAR (MLG) SHOCK STRUT LOWER PIN 19146-3
1. PLANNING INFORMATION
NOTE: Before you do this Service Bulletin, examine all STC, STA or equivalent
action changes to make sure that this Service Bulletin can be completed.
A. Effectivity
CL−600−2B16 aircraft, Serial No. 6050 to 6999.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
Reports found the Main Landing Gear (MLG) trailing arm to shock strut lower pin
cracked due to torsion loading of the joint.
The Service Bulletin gives instructions to increase lubrication frequency using
Aeroshell 7 only. It introduces a new periodic Detail Visual Inspection (DVI) and a
new periodic Non Destructive Testing (NDT) inspection to detect crack/damage on
the LH/RH Main Landing Gear (MLG) shock strut lower pin Part No. 19146−3. It
also gives instructions to replace the shock strut lower pin Part No. 19146−3 if any
crack/damage is found.
C. Description
This Service Bulletin gives instructions in:
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL CL−600−2B16
ATA 32−32
LANDING GEAR
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2020 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jun 30/2020 650−32−004
Page 1 of 12
This Service Bulletin is available at:

### Page 5

PART A, to:
− Do the lubrication of the LH/RH Main Landing Gear (MLG) shock strut lower pin
Part No. 19146−3, and
− Do the installation of the label Part No. 40962−1 on the shock strut assembly,
per Safran Landing Systems, Service Bulletin SB19090−32−9.
PART B, to:
− Do the DVI of the shock strut lower pin Part No. 19146−3, and
− Do Part D if crack/damage is found on the shock strut lower pin Part No.
19146−3, and do the testing.
− Do the Close−Out if no crack/damage is found on the shock strut lower pin Part
No. 19146−3.
PART C, to:
− Do the NDT inspection of the shock strut lower pin Part No. 19146−3, per
Safran Landing Systems, Service Bulletin SB19090−32−9.
− Do Part D if crack/damage is found on the shock strut lower pin Part No.
19146−3, and do the testing.
− Do the testing if no crack/damage is found on the shock strut lower pin Part No.
19146−3.
PART D, to:
− Do the replacement of the cracked/damaged shock strut lower pin Part No.
19146−3, per Safran Landing Systems, Service Bulletin SB19090−32−9.
Testing, to:
− Do the necessary tests to make sure that the system operates correctly.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 2 of 12

### Page 6

D. Compliance
Recommended − Refer to the Specified Time of Compliance in the table below:
ACTIONS COMPLIANCE TABLE EFFECTIVE FROM THIS SERVICE
BULLETIN RELEASE DATE (BASIC ISSUE)
LUBRICATION
SB PART
&
ACTION
FIRST LUBRICATION REPEATLUBRICATION
PART A
Lubrication of
MLG Shock Strut
Lower Joint
200 Flight Hours or 12 months,
whichever comes first from release
date of this Service Bulletin
(Basic Issue)
200 FH or
12 months,
whichever comes
first
INSPECTIONS
SB PART
&
ACTION
FLIGHT CYCLES
(FC)
FIRST
INSPECTION
REPEAT
INSPECTION
PART B
Detailed Visual
Inspection (DVI)
NOTE: DVI not
required if it
coincides with the
NDT inspection.
The NDT
inspection
supersedes the
DVI inspection
Below 600 FC No later than750 FC
Every 400 FH or
24 months,
whichever comes
first
(every second
lubrication
interval)
Above 600 FC Within 150 FC
PART C
Non−Destructive
Testing (NDT)
Eddy Current or
Liquid Penetrant
or
Magnetic Particle
Below 1200 FC No later than1500FC
Every 900 FCAbove 1200 FCand
below 2000 FC
Within 300 FC, or
2200 FC
whichever comes
first
Above 2000 FC within 200 FC
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 3 of 12

### Page 7

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by the EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to SB
650−00−002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
1 man−hour is necessary to do PART A of this Service Bulletin.
2 man−hours are necessary to do PART B of this Service Bulletin.
4 man−hours are necessary to do PART C of this Service Bulletin.
3 man−hours (per side) are necessary to do PART D of this Service Bulletin.
Bombardier Aviation does not pay for the labor to do this Service Bulletin.
G. Material − Cost and Availability
No kit is necessary to do this modification.
The parts in Paragraph 3.B. are necessary to do this modification.
If a pin is found cracked for an in−warranty aircraft, the replacement pin will be Free
of Charge.
For all parts transactions, Bombardier Aviation’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 4 of 12

### Page 8

For those aircraft in new aircraft warranty at the time of service bulletin distribution,
Smart Parts does not pay for the parts at any time.
For those aircraft out of new aircraft warranty at the time of service bulletin
distribution, Smart Parts pays for P/N: 19146−3 if found cracked/damaged.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
24−00−24 S4933959−501 Tag, Circuit Breaker − Red
Commercially Available − Fluid Container
Commercially Available − Grease Gun (Non−pneumatic)
Commercially Available − Hose, Transparent Plastic(Flexible)
Commercially Available − Flashlight for DVI Inspection(See Note 4)
Commercially Available − Mirror for DVI Inspection(See Note 4)
Commercially Available − Torque Wrench 50 to 60 lbf in(5.56 to 6.77 Nm)
NOTES: 1. Refer to the CL−650 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for the CL−650, for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM−WM prevail. Other approved
alternative tools are acceptable and can also be used.
4. This tool is only required for PART B of this Service Bulletin.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 5 of 12

### Page 9

K.
References
− TCCA Airworthiness Directive (Pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−4262,
Rev A.
− Safran Landing Systems, Service Bulletin SB19090−32−9. It can be
downloaded at ’https://landingpad.safranmbd.com/lp/’.
− CL−650 Aircraft Maintenance Manual (AMM), Chapters 6, 7, 12, 24, 29 and 32.
− CL−650 Standard Practice Manual (SPM), Chapters 20 and 51.
− CL−650 Non Destructive Testing Manual (NDTM), Part 1.
L. Other Publications Affected
None.
M. Equivalent Service Bulletins
− For the Challenger 604 aircraft, use the Service Bulletin 604−32−030.
− For the Challenger 605 aircraft, use the Service Bulletin 605−32−007.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the CL−650 Aircraft
Maintenance Manual unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
CL−650 Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all the electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all the hydraulic safety precautions. Refer to AMM 29−00−00−910−801.
(3) Obey all the hydraulic technical precautions. Refer to
AMM 29−00−00−910−802.
(4) Release the hydraulic pressure from the No. 2 system. Refer to
AMM 12−00−04−862−802.
(5) Release the hydraulic pressure from the No. 3 systems. Refer to
AMM 12−00−04−862−804.
(6) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 6 of 12

### Page 10

(7) Install a DO NOT OPERATE THE HYDRAULIC SYSTEM warning tag on the
No. 2 and No. 3 hydraulic systems, on the HYDRAULIC control panel in the
flight compartment.
(8) For PART C and D of this Service Bulletin:
(a) Lift the aircraft on jacks. Refer to AMM 07−10−01−581−801.
(b) Remove the MLG wheel(s) as necessary. Refer to
AMM 32−41−01−000−801.
(c) Remove the brake unit(s) as necessary. Refer to
AMM 32−43−19−000−801.
B. PART A − Lubrication of LH/RH MLG Shock Strut Lower Pin
NOTES: 1. The lubrication of this pin shall be performed using Aeroshell 7 only.
If the previous lubrication was done with Aeroshell 33, at the first
lubrication with Aeroshell 7, a complete purge of the Aeroshell 33
shall be accomplished before lubricating with Aeroshell 7. In this case,
the next lubrication shall be done within 100 FH, and then continue as
per the compliance time specified in the Table in Paragraph 1.D.
Compliance.
(1) Apply grease Aeroshell 7 to the lower joint of the MLG shock absorber. Refer
to AMM 12−20−04−640−802
(2) Install the label Part No. 40962−1 on the shock strut assembly. Refer to Safran
Landing Systems SB19090−32−9 for position.
NOTES: 1. This step is not required if this label is already there.
2. Unless otherwise instructed by Safran Landing Systems, Service
Bulletin SB19090−32−9, seal edges of decal per SPM
20−80−05−400−801.
C. PART B − DVI Inspection of LH/RH MLG Shock Strut Lower Pin
(1) Do the DVI inspection of the shock strut lower pin Part No. 19146−3 using a
mirror and a flashlight. Refer to Figure 1, and do as follows:
(a) Remove the bolt and the end caps to gain access to the pin ends. Refer to
Safran Landing Systems, Service Bulletin SB19090−32−9 for details.
NOTES: 1. Inspect the root of the radii of each of the anti−rotation tangs
all around. Four (4) tangs per pin.
2. Inspect the inner diameter a minimum 0.50 inches (12.7 mm)
deep.
3. Make sure there is no evidence of crack/damage.
(b) If any crack/damage is found on the shock strut lower pin Part No.
19146−3, then do PART D of this Service Bulletin.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 7 of 12

### Page 11

(c) If no crack/damage is found on the shock strut lower pin Part No.
19146−3, then do the steps that follow:
(i) Do the lubrication of the shock strut lower pin as given in PART A.
(ii) Reinstall the end caps and bolt. Refer to Safran Landing Systems,
Service Bulletin SB19090−32−9 for details.
(iii) Go to Paragraph 2.G., Close−Out.
D. PART C − Nondestructive Testing (NDT) Inspection of LH/RH MLG Shock
Strut Lower Pin
(1) Do the Nondestructive Testing (NDT) inspection of the shock strut lower pin
Part No. 19146−3. Refer to Safran Landing Systems, Service Bulletin
SB19090−32−9.
NOTES: 1. For the Liquid Penetrant Inspection (LPI), refer to NDTM, Part 1,
Section 8.
2. For the Magnetic Particle Inspection (MPI), refer to NDTM,
Part 1, Section 7.
(2) Install Brake Unit(s). Refer to AMM 32−43−19−400−801.
(3) Install MLG wheel(s). Refer to AMM 32−41−01−400−801.
(4) Go to Paragraph 2.F., Testing.
E. PART D − Replacement of the LH/RH MLG Shock Strut Lower Pin
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and get an approved disposition to complete this Service Bulletin.
(1) Remove and discard the cracked/damaged shock strut lower pin Part No.
19146−3, per Safran Landing Systems, Service Bulletin SB19090−32−9.
(2) Install the new shock strut lower pin Part No. 19146−3 on the LH/RH MLG
assembly. Refer to Safran Landing Systems, Service Bulletin SB19090−32−9.
(3) Lubricate the joint with grease Aeroshell 7.
NOTE: Make sure the grease is distributed throughout the entire joint.
(4) Install Brake Unit(s). Refer to AMM 32−43−19−400−801.
(5) Install MLG wheel(s). Refer to AMM 32−41−01−400−801.
(6) Go to Paragraph 2.F., Testing.
F. Testing
(1) Lower the aircraft to the ground and remove the jacks. Refer to
AMM 07−10−01−586−801.
(2) Connect and energize the electrical power to the aircraft. Refer to
AMM 24−00−00−861−801.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 8 of 12

### Page 12

(3) Remove the DO NOT OPERATE THE HYDRAULIC SYSTEM warning tag
from the No. 2 and No. 3 hydraulic systems, on the HYDRAULIC control panel
in the flight compartment.
(4) Bleed the MLG Brakes. Refer to AMM 32−43−00−870−801.
(5) Do the operational test of the MLG Brake System. Refer to
AMM 32−43−00−710−801.
G. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
H. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin are completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Part
The part that follows is necessary to do PART A of this Service Bulletin and is
available from Bombardier Aviation Parts Services, Montreal:
NEW PART
NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
40962−1 1 Label − −
The part that follows is necessary to do PART D of this Service Bulletin and is
available from Bombardier Aviation Parts Services, Montreal:
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 9 of 12

### Page 13

NEW PART
NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
19146−3 1
Pin, MLG, Shock
Strut Lower
(See Note 4)
19146−3 Discard
NOTES: 1. The part number(s) for the item(s) listed above are/is subject to
change without revision to this Service Bulletin. In case of
discrepancy between this list and any other list, the Illustrated Parts
Catalog prevails and shall be used to determine the latest part
number.
2. The LH/RH MLG shock strut lower pin is necessary if the shock strut
lower pin is found damaged during inspection.
3. The quantity listed above is for one LH/RH MLG assembly. For both
LH and RH MLG assembly, two set of parts quantity are required.
4. New pin can only be ordered if the DVI/NDT inspection shows that the
original pin is cracked.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aviation does not pay
for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE)
Corrosion
Preventive
Compound
− MIL−PRF−16173 AsNecessary Code: A
Cotter Pin MS24665−302 − AsNecessary Code: B
Grease
Aircraft
and
Instrument
−
MIL−PRF−23827
(Type II)
Aeroshell Grease 7
As
Necessary Code: B
Coating,
Polyurethane,
Fluid
Resistant
− − AsNecessary Code: B
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 10 of 12

### Page 14

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE)
Nut MS14145L7 − AsNecessary Code: B
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Chemsol, Inc.
8423 Boettner Road,
Bridgewater, MI 48115
U.S.A.
Tel.: 1−800−663−4057
Fax: 1−734−944−3781
www.chemsol.com
Code: B
Commercially Available
D. Publications
No publications required.
MODEL CL−600−2B16
Basic Issue: Jun 30/2020 650−32−004
Page 11 of 12

### Page 15

SB650−32−004_001
SHOCK STRUT PIN
(PART NO. 19146−3)
FILLET RADIUS
TANG
INNER DIAMETER
TANG
MODEL CL−600−2B16
Detail Visual Inspection (DVI) of the Shock Strut Lower Pin Part No. 19146−3
Figure 1
Basic Issue: Jun 30/2020 650−32−004
Page 12 of 12

### Page 16

650−32−004 Basic Jun 30/2020
SPECIAL CHECK – MAIN LANDING GEAR – LUBRICATION AND
INSPECTION OF LH/RH MAIN LANDING GEAR (MLG) SHOCK STRUT
LOWER PIN 19146−3
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 17

SERVICE BULLETIN INCORPORATION SHEET − "650−32−004"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
650−32−004 Basic
COMPLIED WITH
YES    NO    N/A
PART A
PART B
PART C
PART D
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
