# Bombardier Service Bulletin 700-24-5014

Copy: Revision 02 ("SB 700-24-5014 R2"), 27 pages: PDF https://openairdocs.org/files/sha256/cf/f1/cff157df4b3f3c066531b9956969eeebb5517fe0e0355577a4fcf08a51daa059; text https://openairdocs.org/service-documents/bombardier/sb-700-24-5014/file/cff157df4b3f.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0019; AD 2019-12-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-24-5014
- Latest revision known: 700-24-5014, Revision 02, dated September 27, 2018 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-24-5014

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2019-12-02](https://openairdocs.org/ad/2019-12-02.md), effective Aug 12, 2019: Revisions 01 and 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-24-5014/proposed.md).

## Text (27 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0019; AD 2019-12-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Revision 01 of this Service Bulletin dated Aug 21/2018 and replace in its
entirety with this Revision 02.
Service Bulletin No. 700−24−5014
Date of Basic Issue Apr 25/2018
Revision No. 01 Dated Aug 21/2018
Revision No. 02 Dated Sep 27/2018
This revision has no effect for aircraft on which the Basic Issue or Revision 01 of this
Service Bulletin was done thus no other action is necessary. Do not sign the log book
if you have not done this revision. Keep the previous log book entry. You may make
an entry as "Not Applicable" for this revision.
This Revision is issued to:
1. Revise, in Paragraph 1.B., the text from “VFG” to “High (VFG and Hydraulic)”.
2. Revise, in Paragraph 1.G., the policy to purchase the Kit No. 700K24−6014. Removed
the “ordered during new aircraft warranty period” statement.
3. Revise, in Paragraph 1.H., the GSE Reference No. to 20X−10−01 for the Circuit Breaker
Tag.
4. Revise, in Paragraph 2.B., the step 2.B.1.(C)(ii) to keep the clamp, wire spacer and
washer for later installation (step (c)(vii)).
5. Change, in Paragraph 2.B., to revise the text from “VFG” to “Hydraulic” in the steps
2.B.1.(e)(i), 2.B.1.(e)(iii) and the illustration title.
6. Revise, in Paragraph 2.C., to add Notes in the steps 2.C.1.(d), 2.C.1.(f), 2.C.1.(h) and
2.C.1.(k)
7. Revise, in Paragraph 2.C., the step 2.C.1.(f), to install the new contacts with crimp
adaptors.
SERVICE BULLETIN
MODEL BD−700−1A11 (BD−700)
700−24−5014
Page 1 of 2
REVISION TRANSMITTAL SHEET

### Page 2

8. Revise, in Paragraph 3.C., to add the consumable.
9. Make miscellaneous minor changes, as necessary, with no change of context.
MODEL BD−700−1A11 (BD−700)
700−24−5014
Page 2 of 2

### Page 3

MODIFICATION - VARIABLE FREQUENCY GENERATOR (VFG) -
MODIFICATION TO THE VFG CABLES INSTALLATION, REAR FUSELAGE
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
RELIABILITY/DISPATCHABILITY/COST AVOIDANCE
COMPLIANCE TIME
Within 24 months from this
Service Bulletin release date
(Basic Issue)
EFFECTIVITY: A/C Serial No. 9386, 9401 and 9445 to 9831
MANPOWER: Up to 5 man−hours, Part A: 3 man−hours, Part B: 2 man−hours.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive, which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services
at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A11 (BD−700)
ATA 24−00
ELECTRICAL POWER
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 1 of 1
This Service Bulletin is available at:

### Page 4

MODIFICATION - VARIABLE FREQUENCY GENERATOR (VFG) -
MODIFICATION TO THE VFG CABLES INSTALLATION, REAR FUSELAGE
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. Please contact your
Regional Manager (RM), Field Service Representative (FSR) or Customer
Service Representative (CSR) to schedule your aircraft as there is a
limited availability. The parts will be allocated on a first come first serve
basis.
For more information on dedicated schedules, refer to SB 700−00−5002.
A. Effectivity
BD−700−1A11 aircraft, Serial No. 9386, 9401 and 9445 to 9831.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A11 (BD−700)
ATA 24−00
ELECTRICAL POWER
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2018 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 1 of 22
This Service Bulletin is available at:

### Page 5

B. Reason
1. Condition:
During visual inspection of the Aft Equipment Bay, low clearance condition
between the High (VFG and Hydraulic) power feeder cables and adjacent
hydraulic lines and/or fuel lines were found in several locations. This condition
may lead to physical contact between the VFG Power feeder cables, hydraulic
system lines and/or fuel lines. Physical contact or chaffing could result in
deterioration of the hydraulic line and/or fuel line wall thickness and VFG power
feeder cables insulation thickness.
2. Evidence:
To this date, evidence of physical contact between the VFG power feeder
cables and the hydraulic lines and/or fuel lines was never reported.
3. Objective/Benefit:
The objective of this Service Bulletin, is to provide customers with instructions to
achieve the minimum required clearance between the VFG power feeder cables
and the adjacent hydraulic and/or fuel lines. This will eliminate the risk of
physical contact/chaffing. The benefits to the operator are improved reliability
and reduced maintenance cost.
C. Description
This Service Bulletin gives instructions in PART A to:
− Get access to the aft compartment area , and
− Modify the VFG power feeder cables routing as instructed in this Service
Bulletin.
This Service Bulletin gives instructions in PART B to:
− Cut the wires at the connectors of the AC Hydraulic Motor Pump,
− Modify the VFG harness routing to meet the installation and clearance
requirements, and
− Do the necessary tests to make sure that the AC Hydraulic Motor Pump
operate(s) correctly.
D. Compliance
Recommended within 24 months from this Service Bulletin release date
(Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 2 of 22

### Page 6

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to SB
700−00−5002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
Up to 5 man−hours are necessary to do this modification and are divided as
follows:
− 3 man−hours are necessary to do Part A of this Service Bulletin.
− 2 man−hours are necessary to do Part B of this Service Bulletin (if required),
including the testing.
The labor required to do PART A of this Service Bulletin is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 24 months from its release date
(Basic Issue).
The labor required to do PART B of this Service Bulletin is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 24 months from its release date
(Basic Issue).
G. Material − Cost and Availability
Kit 700K24−6014 is necessary to do this modification.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 3 of 22

### Page 7

KIT NO. PRICE
700K24−6014 Please contact Bombardier Aerospace
Parts Services, in Montreal, for delivery
lead times and confirmation of prices.
This kit is available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 24
months from this Service Bulletin release date (Basic Issue).
In addition to the kit shown above, the parts in Paragraph 3. may be necessary to
do this PART B of this Service Bulletin.
These parts are available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 24
months from this Service Bulletin release date (Basic Issue).
For all parts transactions, Bombardier Aerospace’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
For those aircraft in new aircraft warranty at the time of Service Bulletin distribution,
Smart Parts Plus does not pay for the kit at any time.
For those aircraft out of new aircraft warranty at the time of Service Bulletin
distribution, Smart Parts Plus pays for the kit for up to 24 months from the Service
Bulletin distribution date (Basic Issue).
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are
used to reserve and manage inventory due to limited availability of rotable stock,
parts and/or kits. Parts are limited, therefore, advance part scheduling with our
In−Service Implementation Team (ISIT) is recommended prior to a maintenance
visit. Please contact your Regional Manager (RM), Field Service Representative
(FSR) or Customer Service Representative (CSR) to schedule your aircraft as there
is a limited availability. The parts will be allocated on a first come first serve basis.
For more information on dedicated schedules, refer to SB 700−00−5002.
H. Tooling
No equipment or special tools are necessary to do PART A of this Service Bulletin.
The equipment and tools listed below are necessary to do PART B of this Service
Bulletin:
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 4 of 22

### Page 8

GSE REFERENCE NO. PART NO. DESCRIPTION
20X−10−01 S4933959−501 Tag, Circuit Breaker
20X−50−03 BM203 Terminator Tool
Commercially Available
M22520/23−01
or
400−B−1
Crimp Tool, Pneumatic
Indent
Commercially Available
M22520/23−04
or
414DA−4N
Die Assy. #4
Commercially Available
M22520/23−11
or
4112
Positioner #4
Commercially Available M81969/29−03
or
M81969/14−07
Insertion/Extraction Tool
NOTES: 1. Refer to the Global 5000 Featuring Global Vision Flight Deck
Illustrated Tool and Equipment Manual (ITEM) to make sure that you
use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for the GL 5000 GVFD,
for acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
WEIGHT MOMENT
+0.15 pounds (0.068 kg) +134 pound−inches (1.543 kgm)
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Modification Summary, R700T400679, Rev. D.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01698,
Rev. A−1.
− Bombardier Aerospace, Kit Drawing KGC991−1558, Rev. B.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 5 of 22

### Page 9

− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
L. Other Publications Affected
None.
M. Equivalent Service Bulletins
For the Global Express and Global Express XRS BD−700−1A10 aircraft, use SB
700−24−089.
For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−24−028.
For the Global 6000 BD−700−1A10 aircraft, use SB 700−24−6014.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 5000
BD−700−1A11 Featuring Global Vision Flight Deck Aircraft Maintenance
Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck Aircraft
Maintenance Manual (AMM), Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Open the aft equipment−compartment door (311BB).
B. PART A − Modification − Installation of Additional Clamps
NOTES: 1. If it is not possible to complete all the instructions in this Service
Bulletin because of the configuration of the aircraft, submit an SRPSA
for analysis and to get an approved disposition to complete this
Service Bulletin.
2. If you find damaged cables that cannot be repaired per Standard
Practices Manual (SPM), submit an SRPSA for an approved
disposition.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 6 of 22

### Page 10

(1) Do the modifications as follow, and as shown on Kit Drawing KGC991−1558:
(a) At the first location, View A, between FS945.50 and FS966.00, and
between STGR 9L and 10L, refer to Figure 1, do as follows:
NOTE: Applicable to aircraft serial no. 9386, 9401 and 9445 to 9790
only.
(i) Install the Fairlead assembly, Part No. GD478−1056−1 (5), on the
hydraulic lines.
(ii) Install the wire spacer, Part No. GD517−4349−1 (8), and the clamp,
Part No. MS21919WDE15 (7), on the VFG cables.
(iii) Attach the fairlead assembly to the clamp with the bolt, Part No.
NAS6203−28 (3), the spacer, Part No. NAS43DD3−24FC (6), the
washer, Part No. NAS1149D0316J (4) and the nut, Part No.
MS21042−3 (9), as shown in View A of kit drawing KGC991−1558.
(iv) Torque the bolt, 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM
20−21−00.
NOTES: 1. Make sure that you have a minimum clearance of 0.50
in (12.7 mm) between the VFG cables and the hydraulic
lines, refer to SPM WM 20−12−00.
2. Make sure that there is no load generated on the
hydraulic lines.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 7 of 22

### Page 11

LOCATION NO.1
GSB2400_001
Modification of VFG Cables Installation
Figure − 1
(b) At the second location, View B, between FS925.00 and FS945.50, on
STGR 13L, refer to Figure 2, do as follows:
(i) Remove and discard the existing bolt that attaches the two clamps,
Part No. MS21919WDE4 (if installed) and Part No. MS21919WDE15,
on the standoff, Part No. B0204037AL−10W.
(ii) Keep the existing washer, Part No. AN960JD10L or NAS1149D0332J
for later installation.
(iii) Install a new spacer, Part No. NAS43DD3−48FC (15), between the
two clamps, and secure with a new bolt, Part No. NAS1801−3−18
(14) and previously removed washer, Part No. AN960JD10L or
NAS1149D0332J on the standoff Part No. B0204037AL−10W, as
shown on view B of Kit Drawing KGC991−1558.
(iv) Torque the new bolt, 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM
20−21−00.
NOTE: Make sure that you have a minimum clearance of 0.50 in
(12.7 mm) between the VFG cables and the fuel lines. Refer
to SPM WM 20−12−00.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 8 of 22

### Page 12

(c) At the third location, Detail F, at FS925.00 between STGR 15L and 16L,
refer to Figure 2, do as follows:
(i) Remove the existing lower left generator run clamp, wire spacer and
the attaching hardware from the APU FADEC run installation. Refer to
Detail F, Pre mod.
(ii) Keep the clamp, wire spacer and washer for later installation (step
(c)(vii)) and discard the attaching bolt.
(iii) Install the removed APU FADEC run clamp with a new bolt Part No.
NAS1801−3−10 (26) and removed washer, Part No.
NAS1149D0332J, as shown in DETAIL F, Post Mod, on Kit Drawing
KGC991−1558.
(iv) Torque the bolt, 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM
20−21−00.
(v) Remove the bolt, washer and spacer that holds the RAD/RAE/RBE,
RAL/RBL/RBA and camera coax (if applicable) installation.
(vi) Discard the bolt and the spacer, keep the washer for later installation.
Refer to Detail F Pre mod.
(vii) Install the removed lower left generator run clamp and wire spacer on
the RAD/RAE/RBE, RAL/RBL/RBA and camera coax (if applicable)
installation with the new bolt, Part No. NAS1801−3−27 (28), removed
washer Part No. NAS1149D0332J, new spacer, Part No. NAS
43DD3−48FC (29) and new spacer, Part No. NAS43DD3−16FC (30)
as shown in DETAIL F, Post Mod, on Kit Drawing KGC991−1558.
(viii) Torque the bolt, 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM
20−21−00.
NOTE: Make sure that you have a minimum clearance of 0.50 in
(12.7 mm) between the VFG cables and the hydraulic lines.
Refer to SPM WM 20−12−00.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 9 of 22

### Page 13

LOCATION NO.2 LOCATION NO.3
GSB2400_002
Modification of VFG Cables Installation
Figure − 2
(d) At the fourth location, View C, on FS893.50, between STGR2L and 3L,
refer to Figure 3, do as follows:
NOTE: Applicable to aircraft 9386, 9401 and 9445 to 9831 only.
(i) As shown in View C, Section D−D on Kit Drawing, install a new
spacer, Part No. NAS43DD3−64FC (21), between the existing
clamps, Part No. MS21919WDE4 for the AC PUMP 2B ground wire
and Part No. MS21919WDE8, for the C/A AC PUMP 2B HYD (SDB)
wire, with a new bolt, Part No. NAS1801−3−21 (20) and the
previously removed washer, Part No. AN960JD10L or
NAS1149D0332J.
(ii) Torque the bolt, 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM
20−21−00.
NOTE: Make sure that you have a minimum clearance of 0.50 in
(12.7mm) between the VFG cables and the hydraulic lines.
Refer to SPM WM 20−12−00.
(e) At the fifth location, FS909.75 between STGR7L and 8L, at the AC
MOTOR PUMP (ACMP) connectors, refer to Figure 3, do as follows:
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 10 of 22

### Page 14

(i) Loosen the clamps holding the Hydraulic Power cables and if
possible, move the power cables to meet minimum clearance
requirement of 0.50 in. (12.7 mm) between the Hydraulic power
cables and the ACMP pressure line.
(ii) Tighten the clamps to secure the cables in position, torque the bolts
20 to 25 lbf in (2.26 to 2.82 Nm). Refer to SPM 20−21−00.
(iii) If it is not possible to meet the minimum clearance requirement of
0.50 in. (12.7 mm) between the Hydraulic power cables and the
ACMP pressure line, because the wires are to long, go to
Paragraph 2.C.
LOCATION NO.4
LOCATION NO.5
GSB2400_003
Modification of Hydraulic Cables installation
Figure 3
C. PART B − Modification − Cutting the Electrical Wires to Meet Installation
Requirements (If Necessary)
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 11 of 22

### Page 15

(1) Do the modification as follows:
(a) In the flight compartment, on the EMS CDU, set the circuit breaker that
follows to LOCKED. Refer to AMM 24−00−00−863−801.
For the No. 1 hydraulic system,
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
HYD HYD PUMP 1B AC 3
For the No. 2 hydraulic system,
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
HYD HYD PUMP 2B AC 2
(b) Remove and discard the lockwire from the connector B51P1 and/or B52P1
as necessary. SPM MM 20−50−00−000−801.
(c) Disconnect connector B51P1 and/or B52P1 from the ACMP.
(d) Remove the power cables, from the connector.
NOTE: Identify the cables location in the connector to make sure you
install them at the same location after the modification.
(e) Cut the power cables so that the routing can meet the installation and
clearance requirements.
NOTE: Make sure that the power cables are not too short and that you
maintain the drip loop.
(f) Install the new contacts with the crimp adaptors, Part No. MS3348−4−6,
on the power cables. Refer to SPM WM 20−00−00.
NOTE: The ground cable does not require the crimp adaptor, Part No.
MS3348−4−6.
(g) Install the power cables in the connector. Refer to SPM WM 20−00−00.
(h) Apply self fusing silicone tape, Part No. N384−8119, on the power cables
and ground cable, and close the connector with the backshell.
NOTE: Approximately 36 inches (91.44 cm) of self fusing silicone tape
will be required.
(i) Safety the backshell on the cables. Torque the screws 20 to 25 lbf in
(2.26 to 2.82 Nm). Refer to SPM MM 20−21−00.
(j) Connect the electrical connector to the ACMP.
(k) Safety the electrical connector with lockwire, Part No. MS20995C20. Refer
to SPM−MM 20−50−00−400−801.
NOTE: It is permissible to use safety cable. Refer to SPM−MM
20−50−00−400−807.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 12 of 22

### Page 16

(l) In the flight compartment, on the EMS CDU, set the circuit breaker that
follows to IN. Refer to AMM 24−00−00−863−802.
For the No. 1 hydraulic system,
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
HYD HYD PUMP 1B AC 3
For the No. 2 hydraulic system,
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
HYD HYD PUMP 2B AC 2
D. Testing
NOTE: Testing is necessary only if Paragraph 2.C. was accomplished.
(1) Do the Operational Test of the No. 1 and No. 2 Hydraulic−System
AC−Motor−Driven Pumps. Refer to AMM 29−12−05−710−801.
E. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Close the aft equipment−compartment door (311BB).
F. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin is completed, make an entry in the aircraft log book and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 13 of 22

### Page 17

3. MATERIAL INFORMATION
A. Kit
Kit 700K24−6014 is necessary to do PART A and contains the parts that follow:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
-
DISPOSITION
GD478−1056−1 1 Fairlead − −
GD517−4349−1 1 Wire Spacer − −
MS21042−3 1 Nut − −
MS21919WDE15 1 Clamp − −
NAS43DD3−16FC 1 Spacer − −
NAS43DD3−24FC 1 Spacer − −
NAS43DD3−48FC 2 Spacer − −
NAS43DD3−64FC 1 Spacer − −
NAS1149D0316J 2 Washer − −
NAS1801−3−10 1 − − −
NAS1801−3−18 1 − − −
NAS1801−3−21 1 − − −
NAS1801−3−27 1 − − −
NAS6203−28 1 − − −
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
The parts that follows are necessary to do PART B of this Service Bulletin and are
available from Bombardier Aerospace Parts Services, Montreal:
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 14 of 22

### Page 18

NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
M39029/30−221 5 See
Note
Contact − −
MS3348−4−6 4 See
Note
Crimp
Adaptor
− −
N384−8119 1 Silicone
Tape, Self
Fusing
− −
Note: Quantity is for one connector.
NOTE: The part numbers for the items listed above are subject to change without
revision to this Service Bulletin. In case of discrepancy between this list
and the Service Bulletin Kit Parts List contained in the respective kit, then
the latter list prevails.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Lockwire MS20995C20 CRES 0.020 in
(0.51 mm)
As Necessary Code: A
Ferrule,
Safety Cable
F20B 0.020 in (0.51
mm)
As Necessary Code: A
Safety Cable C20B 0.020 in (0.51
mm)
As Necessary Code: A
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 15 of 22

### Page 19

SUPPLIERS ADDRESSES BY CODES
Code: A
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A11 (BD−700)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 16 of 22

### Page 20

kgc9911558bs1−PL 
MODEL BD−700−1A11 (BD−700)
PLKGC991−1558 − Kit − Modification To VFG Cables Instl. Rear Fuse
(Sheet 1 of 1, Rev. B)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 17 of 22

### Page 21

kgc9911558bs2−PL 
MODEL BD−700−1A11 (BD−700)
PLKGC991−1558 − Kit − Modification To VFG Cables Instl. Rear Fuse
(Sheet 1 of 1, Rev. B)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 18 of 22

### Page 22

kgc9911558bs1−1 
KGC991−1558 − Kit− −Modification to the VFG Cables Instl. Rear Fuse
(Sheet 1 of 2, Rev. B)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 19 of 22

### Page 23

kgc9911558bs1−2 
KGC991−1558 − Kit − Modification to the VFG Cables Instl. Rear Fuse
(Sheet 1 of 2 , Rev. B − continued)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 20 of 22

### Page 24

kgc9911558bs2−1 
KGC991−1558 − Kit − Modification to the VFG Cables Instl. Rear Fuse
(Sheet 2 of 2, Rev. B)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 21 of 22

### Page 25

kgc9911558bs2−2 
MODEL BD−700−1A11 (BD−700)
KGC991−1558 − Kit − Modification to the VFG Cables Instl. Rear Fuse
(Sheet 2 of 2 , Rev. B − continued)
Basic Issue: Apr 25/2018
Revision 02: Sep 27/2018
700−24−5014
Page 22 of 22

### Page 26

700−24−5014 Rev. 02 Sep 27/2018
MODIFICATION − VARIABLE FREQUENCY GENERATOR (VFG) −
MODIFICATION TO THE VFG CABLES INSTALLATION, REAR
FUSELAGE
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 27

SERVICE BULLETIN INCORPORATION SHEET − "700−24−5014"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−24−5014 02
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
