# Bombardier Service Bulletin 700-27-6009

Copy: Revision 01 ("SB 700-27-6009_v01"), 24 pages: PDF https://openairdocs.org/files/sha256/5f/6d/5f6d39c294713741782e96d8e4322a45cfcebf29075af815acd5c0226e60d000; text https://openairdocs.org/service-documents/bombardier/sb-700-27-6009/file/5f6d39c29471.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0397; AD 2018-20-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-27-6009
- Latest revision known: 700-27-6009, Revision 01, dated July 18, 2017 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-27-6009

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-20-20](https://openairdocs.org/ad/2018-20-20.md), effective Nov 20, 2018: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-27-6009/proposed.md).

## Text (24 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0397; AD 2018-20-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Revision Basic of this Service Bulletin dated May 29/2017, and replace in its
entirety with this Revision 01.
Service Bulletin No. 700−27−6009
Date of Basic Issue May 29/2017
Revision No. 01 Dated Jul 18/2017
This revision has no effect for aircraft on which the Basic Issue of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as "Not Applicable" for this revision.
This revision is issued to:
1. Revise, on the Service Bulletin Summary Sheet, the CAW Fleet Campaign to read NO.
2. Add a note on the Service Bulletin Summary Sheet.
3. Add, in Paragraph 1.A., a table to identify aircraft having met the intent of this Service
Bulletin.
4. Revise, in sub−paragraph 1 of Paragraph 1.B., Reason, the part number to read
GD247−8750−5 instead of GD248−8750−5.
5. Revise, in Paragraph 1.G., the reference to Paragraph 3.B. and add the kit and parts
statement.
6. Revise, step (1)(d) of Paragraph 2.D., to delete “from” and add “to a finished size”.
7. Make miscellaneous minor changes, as necessary, without change of context.
SERVICE BULLETIN
MODEL BD−700−1A10 (BD−700)
700−27−6009
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

SPECIAL CHECK/MODIFICATION — ELEVATOR CONTROL SYSTEM —
INSPECT AND REPLACE (IF NECESSARY) ELEVATOR BRACKETS, PART NO.
GD248–8750–3 AND GD248–8750–4
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 7500 flight cycles or 60 months
from this Service Bulletin release date
(Basic Issue), whichever comes first
EFFECTIVITY: A/C Serial No. 9493 to 9711, 9714, 9716, 9720 to 9726, 9728, 9730,9733, 9743 and 9751
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin will be subject to an Airworthiness Directive which will make it
necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services
at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−31
FLIGHT CONTROLS
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 1 of 1
This Service Bulletin is available at:

### Page 3

SPECIAL CHECK/MODIFICATION — ELEVATOR CONTROL SYSTEM —
INSPECT AND REPLACE (IF NECESSARY) ELEVATOR BRACKETS, PART NO.
GD248–8750–3 AND GD248–8750–4
1. PLANNING INFORMATION
A. Effectivity
BD−700−1A10 aircraft, Serial No. 9493 to 9711, 9714, 9716, 9720 to 9726, 9728,
9730, 9733, 9743 and 9751.
The intent of this Service Bulletin was met on the aircraft that follow with the
Service Request for Product Support Action (SRPSA) listed in the table that follows:
AIRCRAFT SERIAL NUMBER. SRPSA NO.
9551 000161104
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent action
changes to make sure that this bulletin can be completed.
B. Reason
1. Condition:
During a repair on the elevator system, a crack was discovered at the fastener
holes of the elevator bracket, Part No. GD247–8750–5.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−31
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2017 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 1 of 20
This Service Bulletin is available at:

### Page 4

2. Evidence:
After investigation, it was found that a defective tool produced fastener holes of
non−conforming size and/or angle in all four locations on the part. The
non−conforming hole size and/or angle pre−disposed the material to crack upon
fastener installation.
3. Objective/Benefit:
The objective of this Service Bulletin is to do a one−time nondestructive test
inspection (NDT) of both suspected elevator brackets and, if required, replace
the bracket(s).
C. Description
This Service Bulletin gives instructions to:
− Remove access panels,
− Disassemble the elevator control rods,
− Disassemble the elevator load limiters, and
− Disassemble the elevator brackets.
This Service Bulletin gives instructions in PART A, to:
− Do the inspection of the elevator brackets (Eddy Current).
This Service Bulletin gives instructions in PART B, to:
− Disassemble the idler levers,
− Prefit the new elevator brackets, and
− Install the idler levers on the new elevator brackets.
After PART A and/or PART B, as applicable:
− Install previously removed, or new, elevator brackets,
− Assemble the elevator load limiters and the elevator control rods, and
− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended in less than 7500 flight cycles or 60 months from this Service
Bulletin release date (Basic Issue), whichever comes first.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 2 of 20

### Page 5

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA in
accordance with established procedures.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−6002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
3. Labor hours are based on the fact that the modification will be done at
the next 60 month inspection. Therefore no man−hours are allotted to
prepare the aircraft for maintenance or to prepare for this Service
Bulletin.
10 man−hours are necessary to do PART A.
2 man−hours are necessary to do PART B.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 7500 flight cycles or 60 months
from this Service Bulletin release date (Basic Issue), whichever comes first.
G. Material − Cost and Availability
Kit 700K27–6009 is necessary to do this special check/modification.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 3 of 20

### Page 6

KIT NO. PRICE
700K27–6009 Please contact Bombardier Aerospace
Parts Services, in Montreal, for delivery
lead times and confirmation of prices.
In addition to the kit shown above, the parts in Paragraph 3.B. are necessary to do
PART B of this special check/modification.
This kit and parts, if required, in Paragraph 3.B. are available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 7500
flight cycles or 60 months from this Service Bulletin release date (Basic Issue),
whichever comes first.
For all parts transactions, Bombardier Aerospace’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
During or after the above free period, Smart Parts Plus does not pay for the kit or
parts.
H. Tooling
The equipment and tools listed below are necessary to do this special
check/modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
20X−10–01 S4933959–501 Tag, Circuit Breaker (Red
Ring)
27X−31–01 ACS76050 Elevator Rigging−Kit
27X−63–02 92A99107 Kit − Rigging
Spoiler/Aileron
(Clinometer)
Commercially Available 33A103 Cable
Commercially Available NRK−3A Calibration Block
Commercially Available Phasec 3d or Nortec 600 Eddy Current Flaw
Detector
Commercially Available 33A100 MiniDrive
Commercially Available BXUF−16/20 (100 kHz −
1 MHz)
Probe
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 4 of 20

### Page 7

GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Wrench, Torque 22.5 to
140 lbf in (2.55 to 15.80
Nm)
NOTES: 1. Refer to the Global 6000 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
2. Refer to the Liability Statement in the ITEM for the G6000 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive. (Pending)
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01691,
Rev. NC.
− Bombardier Aerospace, Drawing GD249−5700, Rev. C.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
− Global 6000 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 27,
29 and 55.
− Global 6000 BD−700 Structural Repair Manual (SRM), Chapter 51.
− Global 6000 BD−700 Illustrated Tool and Equipment Manual (ITEM), Chapters
20 and 27.
− Global 6000 BD−700 Nondestructive Testing Manual (NDTM), Part 1
Section 6E.
L. Other Publications Affected
None.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 5 of 20

### Page 8

M. Equivalent Service Bulletin
For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use SB 700−27−5009.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6000
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6000 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all the flight control safety precautions. Refer to
AMM 27−00−00−910−801
(3) Obey all hydraulic safety precautions. Refer to AMM 29−00−00−910−801.
(4) Obey all hydraulic technical precautions. Refer to AMM 29−00−00−910−802.
(5) Connect and energize the external ac power. Refer to
AMM 24−41−00−861−801.
(6) On the engine indication and crew alerting system (EICAS), make sure of the
indication that follows:
REFERENCE POSITION/INDICATION
EICAS page The STAB indicator shows the
position pointer at 2.0 degrees ±0.1
degree
(7) Release hydraulic pressure from systems No. 1 and No. 2. Refer to
AMM 29−10−00−862−802.
(8) Release hydraulic pressure from system No. 3. Refer to
AMM 29−10−00−862−804.
(9) Install the applicable warning tags on the pilot’s and copilot’s control wheels
and on the TRIMS control panel.
(10) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to LOCKED. Refer to AMM 24−00−00−863−801.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 6 of 20

### Page 9

SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
FLT CONTROLS RUDDER TRIM DC ESS
FLT CONTROLS P FEEL/RUD LIM 1 DC 1
FLT CONTROLS P FEEL/RUD LIM 2 DC ESS
HYD HYD PUMP 1B AC 3
HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3A AC 4
HYD HYD PUMP 3B AC 1
LIGHTS LOGO LTS AC 4
LIGHTS OVHD 1 INTG LTS BATT
LIGHTS OVHD 2 INTG LTS DC 1
(11) Open and tag the circuit breakers that follow:
LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
(12) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(13) Remove access panel (345CL). Refer to AMM 55−30−13−000−803.
(14) Put a rig pin in the left and right hand bell cranks of the elevator gain changer
mechanism (rig pin P1). Refer to Figure 1.
(15) Remove access panel (345EL). Refer to AMM 55−30−13−000−805.
(16) Remove access panel (352AB). Refer to AMM 55−10−17−000−802.
(17) Put a rig pin in the left hand elevator bell crank (rig pin P2). Refer to Figure 2.
(18) Remove access panel (362AB). Refer to AMM 55−10−17−000−802.
(19) Put a rig pin in the right hand elevator bell crank (rig pin P2). Refer to Figure 2.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 7 of 20

### Page 10

B. Removal of the Elevator Brackets
(1) Disassemble the left and right hand elevator control rods, Items 160, from the
idler levers, Items 200 and 205. Refer to Figure 3 and to the steps that follow:
(a) Remove and discard the cotter pin, Item 185 and the nut, Item 180.
(b) Remove and keep the bolt, Item 170 and the washers, Item 175.
(c) Attach the elevator control rods to adjacent structure as required.
(2) Disassemble the left and right hand elevator load limiters, Items 5, from the
idler levers. Refer to Figure 4 and to the steps that follow:
(a) Remove and discard the cotter pin, Item 30 and the nut, Item 25.
(b) Remove and keep the bolt, Item 15 and the washers, Item 20.
(c) Attach the elevator load limiters to adjacent structure as required.
(3) Disassemble the left and right hand elevator brackets, Items 525 and 530.
Refer to Figure 3 and to the steps that follow:
(a) Remove and keep the four bolts, Item 535 and the four washers, Item 540
from each bracket.
(b) Remove the elevator brackets from the aircraft. The attached idler levers
do not need to be removed from the elevator brackets.
C. PART A — Inspection / NDT of the Elevator Brackets
(1) Do the following on each elevator bracket, Part Nos. GD248 –8750–3 and
GD248–8750–4:
(a) Measure the diameter of the four bolt holes of the bracket. The diameter of
the hole must be from 0.250 to 0.254 in (6.35 to 6.45 mm). Refer to
Drawing GD249–5700, Zone 1C.
(b) If the four bolt holes diameter are within tolerance, continue to step (2) and
perform Eddy Current inspection.
(c) If a bolt hole diameter is not within tolerance, no Eddy Current inspection
is necessary. The bracket needs to be replaced. Continue to Paragraph
2.D.
(2) Perform Eddy Current inspection on the four bolt holes shown in Figure 5 View
B, as per NDTM, Part 1 Section 6E. Use the following tooling (or equivalent):
GSE REFERENCE
NO.
PART NO. DESCRIPTION
− 33A103 Cable
− NRK−3A Calibration Block
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 8 of 20

### Page 11

GSE REFERENCE
NO.
PART NO. DESCRIPTION
− Phasec 3d or Nortec
600
Eddy Current Flaw
Detector
− 33A100 MiniDrive
− BXUF−16/20 (100 kHz
− 1 MHz)
Probe
(3) If no positive indication (crack) is discovered during the Eddy Current
inspection performed in step (2) above, continue to Paragraph 2.E.
(4) If one or more positive indications (cracks) are discovered during the Eddy
Current inspection performed in step (2) above, do PART B of this Service
Bulletin.
D. PART B — Replacement of the Elevator Brackets
(1) Do the following for each of the affected elevator brackets:
(a) Remove and keep the idler lever, Item 200 or 205, from the elevator
bracket. Refer to Figure 3 and to the instructions that follow:
(i) Remove and discard the cotter pin, Item 560, and the nut, Item 555.
(ii) Remove and keep the two washers, Item 550, the bushing, Item 565
and the bolt, Item 545.
(b) Use the affected elevator bracket and create a hole pattern template for
the new elevator bracket.
(c) Use the template and mark the hole positions onto the replacement
elevator bracket.
(d) Open the holes in the replacement bracket to a finished size of 0.250 to
0.254 in (6.35 to 6.45 mm). Refer to SRM Chapter 51–40–08.
(e) Make sure that all four holes align correctly with the mating holes in the
rear spar. Temporarily insert the installation bolts through the new elevator
bracket and spar at all four bolt hole locations. The bolts should slide
freely in the drilled holes.
NOTE: If the bolts do not slide freely in the drilled holes, fill out an
SRPSA and send it by e−mail at:
SRPSA@aero.bombardier.com
(f) Remove the new elevator bracket from the rear spar.
(g) Attach the previously removed idler lever to the new elevator bracket with
the previously removed hardware. Refer to Figure 3.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 9 of 20

### Page 12

(h) Torque the new nut, Part No. MS14145L5, from 100 to 140 lbf in (11.29 to
15.80 Nm) Class 1. Refer to SPM 20–21–00–910–801.
NOTE: Make sure that the idler lever rotates freely around the
attachment point on the elevator bracket after installation.
(i) Install the cotter pin, Part No. MS24665 –159. Refer to SPM
20–50–00–400–802.
E. Installation of the Elevator Brackets
(1) Attach the left and right hand elevator brackets to the rear spar as follows:
(a) Make sure the previously removed bolts, Item 535 and washers, Item 540
have no damage or corrosion.
(b) Attach each elevator bracket with the previously removed bolts, Item 535
and washers, Item 540.
(c) Torque each bolt from 50 to 70 lbf in (5.64 to 7.90 Nm) Class II. Refer to
SPM 20–21–00–910–801.
(2) Attach the left and right hand elevator control rods, Items 160, to the idler
levers, Items 200 and 205. Refer to Figure 3 and to the steps that follow:
(a) Attach each elevator control rod with the previously removed bolts, Item
170 and washers, Item 175.
(b) Install the new nut, Part No. MS14145L4 and torque the nut from 50 to 70
lbf in (5.64 to 7.90 Nm) Class I. Refer to SPM 20–21–00–910–801.
(c) Install the cotter pin, Part No. MS24665 –153. Refer to SPM
20–50–00–400–802.
(3) Attach the left and right hand elevator load limiters, Items 5, to the idler levers.
Refer to Figure 4 and to the steps that follow:
(a) Attach each elevator load limiter with previously removed bolt, Item 15 and
washers, Item 20.
(b) Install the new nut, Part No. MS14145L4 and torque the nut from 50 to 70
lbf in (5.64 to 7.90 Nm) Class I. Refer to SPM 20–21–00–910–801.
(c) Install the cotter pin, Part No. MS24665 –153. Refer to SPM
20–50–00–400–802.
(4) Put a rig pin in each elevator idler levers (rig pin P3). Refer to Figure 2.
(5) Make sure the rig pins P1, P2 and P3 slide freely. If the rig pins do not slide
freely do the following:
(a) Do the rigging of the elevator control rod, Item 160, as follows:
(i) Disconnect the rod, Item 160, as instructed in Paragraph 2.B.(1)(a)
and (b).
(ii) Move the gain changer assembly to allow the rig pin to move freely in
the hole.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 10 of 20

### Page 13

(iii) On Item 160, remove the lockwire from the jam nut and the locking
device.
(iv) Loosen the jam nut.
(v) Adjust the length of the rod, Item 160, in the range of ±0.20 in (±5.08
mm) until the bolt, Item 170 is easy to put in the control rod, Item 160
and the idler lever, Item 200 or 205.
(vi) Move the bolt, Item 170, in and out of the control rod, Item 160 and in
the idler lever, Item 200 or 205, and make sure you get the results
that follow:
a The bolt can move freely.
b The gain changer assembly does not move.
(vii) Torque the jam nut from 50 to 70 lbf in (5.65 to 7.91 Nm) plus running
torque. Refer to SPM 20–21–00–910–801.
(viii) Safety the jam nut to the locking device with lockwire. Refer to SPM
20–50–00–400–801.
(ix) Attach the elevator control rod, Item 160, to the idler lever, Item 200
or 205, as per instructions in Paragraph 2.E.(2)(a) to (c).
(b) Do the rigging of the elevator load limiter, Item 5. Refer to the applicable
instructions to adjust the rod end of the elevator load limiter in
AMM 27−31−13−400−801.
(6) Make sure the rig pins P1, P2 and P3 slide freely.
(7) Remove all the rig pins P1, P2 and P3.
F. Testing
(1) Remove the tags and close the circuit breakers that follow:
LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
(2) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to IN. Refer to AMM 24−00−00−863−802.
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
FLT CONTROLS RUDDER TRIM DC ESS
FLT CONTROLS P FEEL/RUD LIM 1 DC 1
FLT CONTROLS P FEEL/RUD LIM 2 DC ESS
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 11 of 20

### Page 14

SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
HYD HYD PUMP 1B AC 3
HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3A AC 4
HYD HYD PUMP 3B AC 1
LIGHTS LOGO LTS AC 4
LIGHTS OVHD 1 INTG LTS BATT
LIGHTS OVHD 2 INTG LTS DC 1
(3) Do the functional test of the elevator control system. Refer to
AMM 27−31−00−720−801.
G. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Install access panel (345CL). Refer to AMM 55−30−13−400−803.
(3) Install access panel (345EL). Refer to AMM 55−30−13−400−805.
(4) Install access panel (352AB). Refer to AMM 55−10−17−400−802.
(5) Install access panel (362AB). Refer to AMM 55−10−17−400−802.
(6) Remove the warning tags from the pilot’s and copilot’s control wheels and from
the TRIMS control panel.
H. Recording
When any PART of this Service Bulletin is completed, make an entry in the aircraft
log and send the attached Incorporation Notice to Bombardier Business Aircraft
Customer Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
Kit 700K27–6009 is necessary to do this Service Bulletin and contains the parts
that follow:
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 12 of 20

### Page 15

NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
MS14145L4 4 Castellated
Nut
Self−Locking
MS14145L4 Discard
MS24665–153 4 Cotter Pin MS24665–153 Discard
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
The parts that follow are necessary to do PART B of this Service Bulletin and are
available from Bombardier Aerospace Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
GD248–8750–3 1 Elevator
Bracket Assy
(LH)
GD248–8750–3 Discard
GD248–8750–4 1 Elevator
Bracket Assy
(RH)
GD248–8750–4 Discard
MS14145L5 1 per
bracket
Castellated
Nut,
Self−Locking
MS14145L5 Discard
MS24665–159 1 per
bracket
Cotter Pin MS24665–159 Discard
NOTE: The part numbers for the items listed above are subject to change without
revision to this Service Bulletin. In case of discrepancy between this list
and any other list, the Illustrated Parts Catalog prevails and shall be used
to determine the latest part number.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 13 of 20

### Page 16

DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Lacquer,
Gloss, for
Aircraft
− A−A−3165 Color
Red
As Necessary Code: A
Aliphatic
Naphtha
− Specification
TT−N−95, Type
II
As Necessary Code: B
Brush, Paint,
Natural or
Synthetic
Bristle
− − As Necessary Code: B
Flexible
Nonconductive
Ruler or
Straight Edge
− − As Necessary Code: B
High Intensity
Light Source
− − As Necessary Code: B
Nonconductive
Draftsman
Type Circle
Template
− − As Necessary Code: B
Nonconductive
Plugs or Discs
of Various
Diameter
− − As Necessary Code: B
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 14 of 20

### Page 17

SUPPLIERS ADDRESSES BY CODES
Code: A
Tempo Aerospace Inc.
205 Fenmar Dr.
Weston, Ontario
M9L 2X4
Canada
Tel.: (416) 746−2233
Code: B
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 15 of 20

### Page 18

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB2731_003
RIG PIN P1
GAIN CHANGER
INPUT ROD
160
GAIN CHANGER ASSEMBLY
MODEL BD−700−1A10 (BD−700)
Elevator Gain Changer
Figure 1
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 16 of 20

### Page 19

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB2731_002
RIG PIN P2
RIG PIN P3
MODEL BD−700−1A10 (BD−700)
Elevator Gain Changer and Elevator Bell Crank
Figure 2
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 17 of 20

### Page 20

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB2206_005
545
550
535 525
565 550
555
200
180175
170
175
160
540
160
185
560
530
205
MODEL BD−700−1A10 (BD−700)
Elevator Brackets, Idler Levers and Elevator Control Rods
Figure 3
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 18 of 20

### Page 21

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB2731_004
52025
30
20
15
MODEL BD−700−1A10 (BD−700)
Elevator Load Limiters
Figure 4
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 19 of 20

### Page 22

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB2731_001
MODEL BD−700−1A10 (BD−700)
Eddy Current Inspection
Figure 5
Basic Issue: May 29/2017
Revision 01: Jul 18/2017
700−27−6009
Page 20 of 20

### Page 23

700−27−6009 Rev. 01 Jul 18/2017
Special Check/Modification — Elevator Control System —
Inspect and Replace (if necessary) Elevator Brackets, Part No.
GD248–8750–3 and GD248–8750–4
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 24

SERVICE BULLETIN INCORPORATION SHEET − "700−27−6009"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
700−27−6009 01
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
