# Bombardier Service Bulletin 700-27-6503

Copy: Revision 1 ("700-27-6503 Rev01"), 40 pages: PDF https://openairdocs.org/files/sha256/73/f7/73f7b14242a9984bacadb1ccb247c466e3643b0ac9f79e42900dc97511403be0; text https://openairdocs.org/service-documents/bombardier/sb-700-27-6503/file/73f7b14242a9.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0093; AD 2021-10-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-27-6503
- Latest revision known: 700-27-6503, Revision 1, dated December 7, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-27-6503

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-26-09](https://openairdocs.org/ad/2024-26-09.md), effective Mar 11, 2025: Revision 1
- [AD 2021-10-02](https://openairdocs.org/ad/2021-10-02.md), effective Jul 29, 2021: Revision 1

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/bombardier/sb-700-27-6503/proposed.md).

## Text (40 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0093; AD 2021-10-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Basic Issue of this Service Bulletin dated Jul 23/2020, the Information Sheets
dated Aug 27/2020, Nov 12/2020 and Nov 24/2020 and replace in its entirety with this
Revision 01.
Service Bulletin No. 700−27−6503
Date of Basic Issue Jul 23/2020
Revision No. 01 Dated Dec 07/2020
This revision has no effect for aircraft on which the Basic Issue of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as "Not Applicable" for this revision.
This revision is issued to:
1. Revise, in Service Bulletin Summary sheet the Compliance Time as Reference to
Paragraph 1.D.
2. Revise, in Paragraph 1.(C)., to delete the “if required” from the for manual inspection of
the bearings statement.
3. Revise, in Paragraph 1.(D)., Compliance Time as No earlier than 57 months.
4. Add, in Paragraph 1.(F)., work done during new aircraft warranty period.
5. Add, in Paragraph 1.(G)., kit ordered during new aircraft warranty period.
6. Delete, in Paragraph 1.(H)., Tool, Skating and Drill Press.
7. Revise, in Paragraph 1.(H)., Tool, Skating Part number.
8. Delete, in Paragraph 1.(H)., a NOTE 4.
9. Add, in Paragraph 1.(K)., Airworthiness Directive details.
10.Add, in Paragraph 2.A.(13) (d) and (e)., word trailing edge.
SERVICE BULLETIN
MODEL BD−700−1A10 (BD−700)
700−27−6503
Page 1 of 2
REVISION TRANSMITTAL SHEET

### Page 2

11.Revise, in Paragraph 2.A.(20)., for a typographical error.
12.Add, in Paragraph 2.B.(1)., Bearing rejection criteria.
13.Add, in Paragraph 2.B.(4)., a NOTE.
14.Revise, in Paragraph 2.B.(5).(d).(ii)., reference to step (9).
15.Revise, in Paragraph 2.B.(5).(d).(iii)−(iv)., reference to step (6).
16.Add, in Figure 2, the section view of the bearing and torque tube.
17.Delete, in Paragraph 2.B., step 6.
18.Revise, in Figure 4, the orientation of the bolts.
19.Add, in Paragraph 2.B.(9), Steps (b) and (c).
20.Delete, in Paragraph 2.B.(10) and (11), reference of step (4)(d).
21.Add, in Paragraph 2.B.(10), a NOTE.
22.Revise, in Paragraph 2.B.(11).(c)., application of sealant.
23.Revise, in Paragraph 2.B.(11).(g)., reference to 2.D Testing.
24.Add, in Paragraph 2.C., a NOTE for Bearing rejection criteria.
25.Revise, in Figure 5, the orientation of the brackets.
26.Add, in Paragraph 2.C.(2), lower brackets.
27.Revise, in Paragraph 2.C.(16).(b)., application of sealant.
28.Revise, in Paragraph 3.A.Kit, QTY of Tapered Pins Part No. AN386−1−10 and
AN386−1−11 from 2 to 4, Washer Part No. AN975−3 from 4 to 8, Nut Part No.
MS17826−3 from 4 to 8 and Cotter Pin Part No. MS24665−136 from 10 to 12.
29.Revise, in Paragraph 3.B.Parts, QTY of Cotter Pin Part No. MS24665−136 from 2 to 4.
30.Revise, in TABLE 4, Column FRICTION as POTENTIAL FRICTION and SEIZED as
POTENTIALLY SEIZED.
31.Make miscellaneous minor changes, as necessary, with no change of context.
MODEL BD−700−1A10 (BD−700)
700−27−6503
Page 2 of 2

### Page 3

SPECIAL CHECK — ELEVATOR CONTROL SYSTEM —
INSPECTION OF TORQUE TUBE BEARINGS
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 9861, 9872, and 60001 to 61999
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive, which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−31
FLIGHT CONTROLS
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 1 of 1
This Service Bulletin is available at:

### Page 4

SPECIAL CHECK — ELEVATOR CONTROL SYSTEM —
INSPECTION OF TORQUE TUBE BEARINGS
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Recommended Service Bulletin is intended as an interim solution.
The data collected from Appendix A will be used to evaluate in service
aircraft condition, and provide guidance toward a permanent solution.
Thus Appendix A of this Service Bulletin must be filled out and returned to
Bombardier Aerospace.
A. Effectivity
BD−700−1A10 aircraft, Serial No. 9861, 9872, and 60001 to 61999.
B. Reason
1. Condition:
Bombardier has received 2 reported cases of sand and dust accumulation in the
location of the elevator torque tube installation, in the center aft area of the
horizontal stabilizer. Both RHS and LHS torque tubes were not rotating freely
and showed signs of contamination.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−31
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2020 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 1 of 35
This Service Bulletin is available at:

### Page 5

2. Evidence:
The torque tube assemblies were returned to Bombardier for a full teardown
inspection and it was concluded that one of the four bearings was found seized
due to sand contamination. The other three bearings had higher than normal
rolling resistance but were considered free to rotate. Corrosion was found
between inner races and torque tubes.
A coating of dust in this area is not unusual, but appreciable accumulation of
sand and dust on the bearings/housings and torque tube assembly, may
increase the risk of contamination of the bearings and potential seizure.
3. Objective/Benefit:
The objective is to inspect for sand and dust contamination in the location of the
elevator torque tube installation in order to prevent bearings contamination
and/or seizures. Replacing any bearing that would show signs of contamination.
Report back finding to Bombardier Aerospace, to be able to properly assess the
fleet in the engineering evaluation.
C. Description
This Service Bulletin gives instructions in PART A to:
− Do a functional test of the elevator control system,
− Get access to the elevator torque tubes,
− Do a visual inspection of the torque tubes,
− Clean the area,
− Repeat 25 cycles of the elevator surfaces,
− Inspect the bearings,
− Disconnect the input and output control rods,
− Do a manual inspection of the bearings,
− Record the inspection results on Appendix A (attached), and
− Return Appendix A to Bombardier Aerospace,
This Service Bulletin gives instructions in PART B to:
− Remove the torque tube assemblies from the aircraft,
− Disassemble the torque tubes,
− Remove bearings from the bracket assemblies,
− Perform NDT on the brackets,
− Stake the new bearings,
− Assemble the torque tubes,
− Install the torque tube assemblies on the aircraft,
− Reconnect the input and output control rods, and
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 2 of 35

### Page 6

− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended whichever is later:
− Within 36 months from Service Bulletin release (Basic Issue).
− No earlier than 57 months and no later than 63 months from the date of aircraft
manufacture, as identified on the identification plate of the aircraft.
NOTES: 1. If it is not possible to complete all the instructions in this Service
Bulletin because of the aircraft configuration, submit an SRPSA for
analysis and to get an approved disposition to complete this Service
Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−6502.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
3. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
12 man−hours are necessary to do PART A of this special check.
5 man−hours are necessary to do PART B of this special check.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 3 of 35

### Page 7

The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period,
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled within 36 months from its release date (Basic
Issue), or within 63 months of aircraft Certificate of Airworthiness issuance,
whichever is later.
G. Material − Cost and Availability
Kit 700K27−6503 is necessary to do PART B of this special check.
KIT NO. PRICE
700K27−6503 Please contact Bombardier Aerospace
Parts Services, in Montreal, for delivery
lead times and confirmation of prices.
In addition to the kit shown above, the parts in Paragraph 3 are necessary to do this
special check.
The kit is available at no cost if:
− ordered during new aircraft warranty period, and
− a no−charge purchase order is sent to Bombardier Aerospace within 36 months
from this Service Bulletin release date (Basic Issue), or within 63 months of
aircraft Certificate of Airworthiness issuance, whichever is later.
During or after the above free period, Smart Parts does not pay for the kit.
H. Tooling
The equipment and tools listed below are necessary to do this special check:
GSE REFERENCE NO. PART NO. DESCRIPTION
20−00−04 950−315 Digital Inclinometer
20X−10−01 S4933959−501 Tag, Circuit Breaker
27X−00−03 G700−270003−1 Kit − Rudder/Elevator
Rigging Pins
27X−31−01 ACS76050 Elevator Rigging−Kit
27X−63−02 92A99107 Kit − Rigging
Spoiler/Aileron
(Clinometer)
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 4 of 35

### Page 8

GSE REFERENCE NO. PART NO. DESCRIPTION
− GT995040−28
(See Note 4)
Tool, Skating
Commercially Available − Glass, Magnifying
10X−25X
Commercially Available − Press, Hydraulic
(See Note 6)
Commercially Available − Vacuum
Commercially Available − Wrench, Torque 25 to 30
lbf in (2.83 to 3.38 Nm)
Commercially Available − Wrench, Torque 30 to 40
lbf in (3.39 to 4.51 Nm)
NOTES: 1. Refer to the Global 6500 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
2. Refer to the Liability Statement in the ITEM for the G6500 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
4. Bombardier Aerospace part number.
5. Capacity as applicable. The highest possible load value necessary in
this subject is 72,188 lb (32,744 Kg)
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive, CF−2020−29 − BOMBARDIER: Flight Controls −
Elevator Control System − Vertical Torque Tube Seizure − Sand Contamination
of Bearing.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 5 of 35

### Page 9

− EASA Airworthiness Directive, CF−2020−29 − BOMBARDIER: Flight Controls −
Elevator Control System − Vertical Torque Tube Seizure − Sand Contamination
of Bearing.
− FAA Airworthiness Directive, (pending).
− AW700−27−0786 Release of AD CF−2020−29, Flight Controls − Elevator
Control System − Vertical Torque Tube Seizure − Sand Contamination of
Bearing.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01782,
Rev. −−.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapters 20 and 51.
− Bombardier Aerospace, Drawing GC413−3650, Rev. NC.
− Appendix A − Information Feedback Sheet (attached).
− Global 6500 BD−700 Aircraft Maintenance Manual (AMM), Chapters 24, 27, 29
and 55.
− Global 6500 BD−700 Aircraft Illustrated Parts Catalog (AIPC), Chapters 27 and
55.
− Global 6500 BD−700 Illustrated Tool and Equipment Manual (ITEM), Chapters
20 and 27.
− Global 6500 BD−700 Nondestructive Testing Manual (NDT), Part 1 SECTION 8.
− Global 6500 BD−700 Structural Repair Manual (SRM), Chapter 51.
L. Other Publications Affected
None.
M. Equivalent Service Bulletins
For the Global Express and Global Express XRS BD−700−1A10 aircraft, use
SB 700−27−083.
For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−27−041.
For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use SB 700−27−5012.
For the Global 6000 BD−700−1A10 aircraft, use SB 700−27−6012.
For the Global 5500 BD−700−1A11 aircraft, use SB 700−27−5503.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 6 of 35

### Page 10

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6500
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6500 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all flight control safety precautions. Refer to AMM 27−00−00−910−801.
(3) Obey all hydraulic safety precautions. Refer to AMM 29−00−00−910−801.
(4) Obey all hydraulic technical safety precautions. Refer to
AMM 29−00−00−910−802.
(5) Install warning tags on the pilot and copilot control wheels and rudder pedals,
and on the AIL/RUD/STAB TRIMS control panel.
(6) Remove lower visors (346JL/346JR). Refer to AMM 55−10−05−000−810.
(7) Remove upper visors (346KL/346KR). Refer to AMM 55−10−05−000−809.
(8) Remove lower trailing−edge access−panels (352AB/362AB). Refer to
AMM 55−10−17−000−802.
(9) Remove access panel for the elevator control bellcrank (345EL). Refer to
AMM 55−30−13−000−805.
(10) Connect the electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(11) Make sure the pitch trim is set as follows:
REFERENCE POSITION/INDICATION
EICAS primary page STAB indicator shows position
pointer at 2 degrees ±0.1 degree
(12) Install a clinometer on each elevator control surface at BL35.00 at a distance of
2.00 in (50.80 mm) from the elevator trailing edge.
NOTE: Make sure the clinometers are at the center of and parallel to the axes
of the PCU actuators.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 7 of 35

### Page 11

(13) Set the clinometer to zero as follows. Refer to AMM 27−31−00−720−801:
(a) Pressurize the aircraft hydraulic systems No. 1 and No. 2. Refer to
AMM 29−10−00−862−801.
(b) Pressurize the No. 3 hydraulic system. Refer to
AMM 29−10−00−862−803.
(c) Cycle the elevators 5 times.
(d) Make sure that the upper surface trailing−edge of the elevator is flush
±0.120 in (±3.04 mm) with the tip fairing.
(e) The elevator trailing−edge inner−corners mismatch should be less than or
equal to 0.280 in (7.11 mm).
(f) Set the clinometer to zero.
(g) If the upper surface of the elevator is not flush with the tip fairing and the
center mismatch is more than 0.280 in (7.11 mm), use of elevator rigging
fixture GSE 27X−31−01, and set the clinometer to zero as follows:
(i) Release the hydraulic pressure from the No. 1 and No. 2 hydraulic
systems. Refer to AMM 29−10−00−862−802.
(ii) Release the hydraulic pressure from the No. 3 hydraulic system.
Refer to AMM 29−10−00−862−804.
(iii) Install the elevator rigging fixture on the horizontal stabilizer to set the
elevator control surfaces to zero.
NOTE: Make sure the stabilizer and the elevator are touching the
rigging fixture contour.
(iv) Set the clinometer to zero.
(v) Remove the elevator rigging fixture from the horizontal stabilizer.
(14) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to OUT. Refer to AMM 24−00−00−863−801:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
ENGINE L ENG IGN 1 BATT
ENGINE L ENG IGN 2 BATT
ENGINE R ENG IGN 1 BATT
ENGINE R ENG IGN 2 BATT
(15) Pressurize the No. 1 and No. 2 hydraulic systems. Refer to
AMM 29−10−00−862−801.
(16) Pressurize the No. 3 hydraulic system. Refer to AMM 29−10−00−862−803.
(17) On the control columns, do as follows:
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 8 of 35

### Page 12

PROCEDURE APPLICABLE RESULT
Pull and hold the control columns
fully aft.
On the clinometers, the two elevators
show 24 degrees ±0.5 degree up.
On the EICAS, on the FLIGHT
CONTROLS page, ELEV position
pointers go fully up.
Release the control columns. On the clinometers, the two elevators
show 0 degree ±0.5 degree. On the
EICAS, on the FLIGHT CONTROLS
page, ELEV position pointers go
back to center.
Push and hold the control columns
fully forward.
On the clinometers, the two elevators
show 19 degrees ±0.5 degree down.
On the EICAS, on the FLIGHT
CONTROLS page, ELEV position
pointers go fully down.
Release the control columns. On the clinometers, the two elevators
show 0 degree ±0.5 degree. On the
EICAS, on the FLIGHT CONTROLS
page, ELEV position pointers go
back to center.
(18) Note the measured angles in Table 2 of Appendix A.
(19) Release hydraulic pressure from systems No. 1 and No. 2. Refer to
AMM 29−10−00−862−802.
(20) Release hydraulic pressure from system No. 3. Refer to
AMM 29−10−00−862−804.
(21) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to LOCKED. Refer to AMM 24−00−00−863−801:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
FLT CONTROL P FEEL/RUD LIM 1 DC 1
FLT CONTROL P FEEL/RUD LIM 2 DC ESS
FLT CONTROL RUDDER TRIM DC ESS
HYD HYD PUMP 1B AC 3
HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3B AC 1
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 9 of 35

### Page 13

HYD HYD PUMP 3A AC 4
(22) Open and tag the circuit breakers that follow:
LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
B. PART A − Bearings Inspection
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Bearing rejection criteria:
NOTE: If necessary or in any concerns, submit an SRPSA for analysis and to
get Bombardier support in the assessment of this inspection.
(a) If the torque tube bearing passes the cycle inspection (line check) and
manual inspection (manual feel for bearing ratcheting), then no
replacement of the bearing is required.
(b) If the torque tube bearing passes the cycle inspection (line check) and fails
the manual inspection, then replace the four bearings.
(c) If the torque tube bearing fails the cycle inspection (line check) but passes
the manual inspection for bearing ratcheting, then the bearings are
acceptable.
(2) Do the visual inspection as follows. Refer to Figure 1:
(a) Visually inspect the area of the torque tube assemblies, Part No.
GC413−3650−1 and GC413−3650−2 for any accumulation of sand and/or
dust. Record the condition on line 1 of Table 3, in Appendix A.
(b) Visually inspect the bearings of the torque tube assemblies for any
accumulations of sand and/or dust. Inspect the locations circled in red in
Figure 1. Record the condition on line 2 of Table 3, in Appendix A.
(c) Capture a photograph of the area.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 10 of 35

### Page 14

SB700−27−6012_011
NOTE
Bearing inspection area.1
FS1164.235
DUST AND SAND ACCUMULATION
1
1
1
1
GC413−3650−1
(TORQUE TUBE
ASSEMBLY)
GC413−3650−2
(TORQUE TUBE
ASSEMBLY)
MODEL BD−700−1A10 (BD−700)
Figure 1
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 11 of 35

### Page 15

(3) Remove any sand and/or dust accumulation with a vacuum cleaner.
NOTE: DO NOT USE compressed air on the torque tube bearings.
(4) Use soft bristled brush and lint free cloth to remove the remainder of the sand
and/or dust deposits from the vertical torque tube and support bearings.  Do
not use compressed air or cleaning fluids on the bearing and housing as it may
allow migration of fluid and contamination into the bearings.
NOTE: The bearings are maintenance free and if contaminated and inner
race rotation affected, need to be replaced.
(5) Inspect the torque tube bearings as follows. Refer to Figure 2:
(a) With a marker, identify each bracket as applicable (LHS, RHS, Upper,
Lower).
(b) With a marker, make a straight line over the bracket, the inner race and
the torque tube. This mark is the reference line.
NOTE: Two persons are necessary to do this inspection. One person is
in the cockpit and the other at the torque tubes location.
(c) Pressurize the No. 3 hydraulic system. Refer to AMM
29−10−00−862−803.
(d) Move the elevator surfaces from center to full up and full down, then back
to center. This counts as 1 cycle. Repeat for 25 cycles and note the
following on the torque tube:
NOTE: The inner race and the torque tube must rotate together with no
friction between the inner and outer race of the bearing.
(i) Capture a photograph of each bracket, showing the marking after 25
cycles.
(ii) If the mark is aligned back to the original position after 25 cycles,
record the result as PASS in Table 4 of Appendix A, and continue to
step (9) for the manual inspection.
(iii) If the torque tube rotates but the inner race does not, then the inner
and outer race may be jammed. Record the result as SEIZED in
Table 4 of Appendix A, and continue to step (6).
(iv) If the torque tube and the inner race rotate but the mark is not aligned
after 25 cycles, then the inner and outer race may have friction.
Record the result as FRICTION in Table 4 of Appendix A, and
continue to step (6).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 12 of 35

### Page 16 (OCR)

Global 6500
MODEL BD-700-1A10 (BD-700)
GS417-0038-6
(BRACKET)
MS27646-41
(BEARING)
GC413-3650-1 (LH)
GC413-3650-2 (RH)
(TORQUE TUBE ASSY)
GS417-005C
W 94287546
START/END POSITION
GS417-005c  SB700-27-6012_021
W 94287546
INNER RACE FOLLOWING THE TUBE DURING ROTATION
Figure 2
(Sheet 1 of 2)
Basic Issue: Jul 23/2020  700-27-6503
I Revision 01: Dec 07/2020  Page 13 of 35

### Page 17 (OCR)

Global 6500
MODEL BD-700-1A10 (BD-700)
6S417-005L
W 94287546
INNER RACE AND OUTER RACE JAMMED
TORQUE TUBE ROTATING INSIDE OF RACE
GS417-005c  W 94287546  65417-005c  W 94287516  SB700-27-6012_022
INNER RACE HAS FRICTION WITH  INNER RACE NOT FOLLOWING
OUTER RACE  DURING ROTATION
REJECTION
Figure 2
(Sheet 2 of 2)
Basic Issue: Jul 23/2020  700-27-6503
I Revision 01: Dec 07/2020  Page 14 of 35

### Page 18

(6) Release hydraulic pressure from system No. 3. Refer to AMM
29−10−00−862−804.
(7) Install rig pins in the elevator control system. Refer to Figure 3:
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 15 of 35

### Page 19

SB700−27−6012_001
16
15
MODEL BD−700−1A10 (BD−700)
Figure 3
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 16 of 35

### Page 20

(8) Disconnect input and output control rods, Part No. GC415−0030−25 and
GC415−0030−9, from the torque tube assembly as follows. Refer to Figure 4:
(a) Remove and discard cotter pin, Part No. MS24665−136, Refer to
SPM−MM−20−50−00−000−802.
(b) Remove and keep the nut, Part No. MS17826−4, the washer, Part No.
AN960−416L and the bolt, Part No. NAS6204−12D.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 17 of 35

### Page 21

SB700−27−6012_041
NAS6204−12D
(BOLT)
GC415−0030−9
(CONTROL ROD)
MS24665−136
(COTTER PIN)MS17826−4
(NUT)
AN960−416L
(WASHER)
NAS6204−12D
(BOLT)
GC415−0030−25
(CONTROL ROD)
AN960−416L
(WASHER)
MS24665−136
(COTTER PIN)
MS17826−4
(NUT)
GC413−3650−1 (LH)
GC413−3650−2 (RH)
(TORQUE TUBE ASSY)
MODEL BD−700−1A10 (BD−700)
Figure 4
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 18 of 35

### Page 22

(9) Do the following manual inspection:
(a) Apply light finger pressure at the torque tube and, at a slow rate, manually
rotate the torque tube in clockwise and counter clockwise directions. The
torque tube should rotate freely without any binding, ratcheting or seizure.
(b) Make sure that the inner race is following the input to the torque tube.
(c) The intent is to find if the bearings are experiencing any signs of binding,
ratcheting and seizure.
(d) Record the condition of each bearing (pass, binding/ratcheting or seized)
in Table 5 of Appendix A.
(e) Send Appendix A and all the photographs to Bombardier Aerospace.
(10) If any of the torque tube bearings do not pass the inspection of step (9), then
all 4 bearings must be replaced. Go to Paragraph 2.C., Bearings Replacement.
NOTE: Make sure the inner race is following the input to the torque tube.
(11) If all the torque tube bearings pass the inspection of step (9), then do the
following:
(a) Connect input and output control rods, Part No. GC415−0030−25 and
GC415−0030−9, to the torque tube assembly as follows. Refer to Figure 4,
view B.
NOTE: Make sure that the mating surfaces are clean with no corrosion,
paint, grease, or preservation fluids.
(b) Align the control rod with the holes on the torque tube assembly.
(c) Apply the sealant to the exterior side only of the hole on the torque tube
assembly (where mating the bolt head) or under the bolt head only and
install the bolt, Part No. NAS6204−12D, the washer, Part No.
AN960−416L and the nut, Part No. MS17826−4. Refer to
SPM−MM−51−23−00−390−809.
(d) Torque the nut from 20 to 25 lbf in (2.83 to 3.38 Nm). Refer to
AMM 20−21−00−910−801.
(e) Safety the nut with cotter pin, Part No. MS24665−136. Refer to
AMM 20−50−00−400−802.
(f) Remove rig pins from the elevator control system. Refer to Figure 3.
(g) Go to Paragraph 2.D. Testing.
C. PART B − Bearings Replacement
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
Before you begin the bearing replacement procedure, make sure that the
bearing rejection criteria is confirmed. Refer to Paragraph 2.B.1 (a, b and
c).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 19 of 35

### Page 23

(1) Remove the torque tube assemblies, Part No. GC413−3650−1 and
GC413−3650−2 from the aircraft as follows. Refer to Figure 5:
(a) At the lower section of the torque tube, remove and discard the cotter pins,
Part No. MS24665−73. Refer to View B and to
SPM−MM−20−50−00−000−802.
(b) Remove and keep the nuts, Part No. MS14145L3, the washers, Part No.
AN960−10L and the bolts, Part No. NAS6203−9D.
(c) Remove and keep the hydraulic protection plate, Part No.
GS477−0048−003.
(d) At the upper section of the torque tube, remove and discard the cotter
pins, Part No. MS24665−136. Refer to View C and to
SPM−MM−20−50−00−000−802.
(e) Remove and keep the nuts, Part No. MS14145L4, the washers, Part No.
AN960−416L and the bolts, Part No. NAS6204−8D.
(f) Remove torque tube assemblies.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 20 of 35

### Page 24

SB700−27−6012_031
MODEL BD−700−1A10 (BD−700)
Figure 5
(Sheet 1 of 2)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 21 of 35

### Page 25

SB700−27−6012_032
GS417−0038−6
(BRACKET)
MS27646−41
(BALL BEARING)
MS27646−41
(BALL BEARING)
GS417−0038−5
(BRACKET)
GS477−0048−003
(HYDRAULIC PROTECTION
PLATE)
MS24665−136
(COTTER PIN)
MS27646−41
(BALL BEARING)MS27646−41
(BALL BEARING)
GS417−0032−4
(BRACKET)
NAS6204−8D
(BOLT)
AN960−416L
(WASHER)
MS14145L4
(NUT)
GS417−0032−3
(BRACKET)
AN960−416L
(WASHER)
MS24665−136
(COTTER PIN)
MS14145L4
(NUT)
NAS6204−8D
(BOLT)
AN960−10L
(WASHER)
MS14145L3
(NUT) MS24665−73
(COTTER PIN)
NAS6203−9D
(BOLT)
MODEL BD−700−1A10 (BD−700)
Figure 5
(Sheet 2 of 2)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 22 of 35

### Page 26

(2) Remove the upper and lower levers , Part No. GC413−3604−1 from the torque
tubes, Part No. GC413−3608−1 and GC413−3608−2 as follows:
(a) Refer to Figure 6, View A−A:
(i) Remove and discard the cotter pin, Part No. MS24665−132. Refer to
SPM−MM−20−50−00−000−802.
(ii) Remove and discard the nut, Part No. MS17826−3 and the washer,
Part No. AN975−3.
(iii) Remove and discard the tapered pin, Part No. AN386−1−10. Refer to
SRM 51−43−00−00.
(b) Refer to Figure 6, View B−B:
(i) Remove and discard the cotter pin, Part No. MS24665−132. Refer to
SPM−MM−20−50−00−000−802.
(ii) Remove and discard the nut, Part No. MS17826−3 and the washer,
Part No. AN975−3.
(iii) Remove and discard the tapered pin, Part No. AN386−1−11. Refer to
SRM 51−43−00−00.
(c) Remove and keep levers.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 23 of 35

### Page 27

SB700−27−6012−S1−PL 
MODEL BD−700−1A10 (BD−700)
Figure 6
(Sheet 1 of 2)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 24 of 35

### Page 28

SB700−27−6012−S2−PL 
MODEL BD−700−1A10 (BD−700)
Figure 6
(Sheet 2 of 2)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 25 of 35

### Page 29

SB700−27−6012−S1 
MODEL BD−700−1A10 (BD−700)
Figure 6
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 26 of 35

### Page 30

(3) Slide out the upper bracket assembly, Part No. GS417−0050−3 (LHS) and
GS417−0050−4 (RHS) from the torque tube.
(4) Slide out the lower bracket assembly, Part No. GS417−0051−5 (LHS) and
GS417−0051−6 (RHS) from the torque tube.
(5) Inspect the torque tube for fretting and wear. If present, send SRPSA to
Bombardier Aerospace with detail of damage for engineering disposition.
(6) Remove the bearing (staked anti−friction), Part No. MS27646−41 from the
upper brackets, Part No. GS417−0032−3 (LHS) and GS417−0032−4 (RHS).
Refer to SRM 51−79−05−00.
(7) Do a liquid penetrant inspection of the housing bore and the adjacent areas for
cracks. No cracks are permitted. Refer to SRM 51−79−05−00 and NDTM
Part 1 SECTION 8.
(8) Install the new bearing, Part No. MS27646−41 to the upper brackets. Refer to
SRM 51−79−05−00.
(9) Remove the bearing, Part No. MS27646−41 from the lower brackets, Part No.
GS417−0038−6 (LHS) and GS417−0038−5 (RHS). Refer to
SRM 51−79−05−00.
(10) Do a liquid penetrant inspection of the housing bore and the adjacent areas for
cracks. No cracks are permitted. Refer to SRM 51−79−05−00 and NDTM
Part 1 SECTION 8.
(11) Install the new bearing, Part No. MS27646−41 to the lower brackets. Refer to
SRM 51−79−05−00.
(12) Slide the torque tube, Part No. GC413−3608−1 in the lower bracket assembly,
Part No. GS417−0051−5 (LHS) and GS417−0051−6 (RHS).
(13) Slide the torque tube, Part No. GC413−3608−1 in the upper bracket assembly,
Part No. GS417−0050−3 (LHS) and GS417−0050−4 (RHS).
(14) Install the lever, Part No. GC413−3604−1 to the torque tube as follows:
(a) Refer to Figure 6, View B−B:
(i) Position the lever on torque tube.
(ii) Install new tapered pin, Part No. AN386−1−11. Refer to
SRM 51−43−00−00.
(iii) Install washer, Part No. AN975−3 and nut, Part No. MS17826−3.
(iv) Torque nut from 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to
SPM−MM−20−21−00−910−801.
(v) Safety the nut with cotter pin, Part No. MS24665−132. Refer to
SPM−MM−20−50−00−400−802.
(b) Refer to Figure 6, View A−A:
(i) Install new tapered pin, Part No. AN386−1−10. Refer to
SRM 51−43−00−00.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 27 of 35

### Page 31

(ii) Install washer, Part No. AN975−3 and nut, Part No. MS17826−3.
(iii) Torque nut from 20 to 25 lbf in (2.26 to 2.82 Nm). Refer to
SPM−MM−20−21−00−910−801.
(iv) Safety the nut with cotter pin, Part No. MS24665−132. Refer to
SPM−MM−20−50−00−400−802.
(15) Install torque tube assembly to the aircraft as follows. Refer to Figure 5:
(a) At the upper section of the torque tube, install the retained bolts, Part No.
NAS6204−8D, the washers, Part No. AN960−416L and the nuts, Part No.
MS14145L4. Refer to view C.
(b) Torque nuts from 30 to 40 lbf in (3.39 to 4.51 Nm). Refer to
SPM−MM−20−21−00−910−801.
(c) Safety the nuts with cotter pins, Part No. MS24665−136. Refer to
SPM−MM−20−50−00−400−802.
(d) At the lower section of the torque tube, install the hydraulic protection
plate, Part No. GS477−0048−003, the retained bolts, Part No.
NAS6203−9D, the washers, Part No. AN960−10L, the nuts, Part No.
MS14145L3. Refer to view B.
(e) Torque nuts from 12 to 15 lbf in (1.36 to 1.69 Nm). Refer to
SPM−MM−20−21−00−910−801.
(f) Safety the nuts with cotter pin, Part No. MS24665−73. Refer to
SPM−MM−20−50−00−400−802.
(16) Connect input and output control rods, Part No. GC415−0030−25 and
GC415−0030−9, to the torque tube assembly as follows. Refer to Figure 4,
view B.
NOTE: Make sure that the mating surfaces are clean with no corrosion, paint,
grease, or preservation fluids.
(a) Align the control rod with the holes on the torque tube assembly.
(b) Apply the sealant to the exterior side only of the hole on the torque tube
assembly (where mating the bolt head) or under the bolt head only and
install the bolt, Part No. NAS6204−12D, the washer, Part No.
AN960−416L and the nut, Part No. MS17826−4. Refer to
SPM−MM−51−23−00−390−809.
(c) Torque the nut from 20 to 25 lbf in (2.83 to 3.38 Nm). Refer to
AMM 20−21−00−910−801.
(d) Safety the nut with cotter pin, Part No. MS24665−136. Refer to
AMM 20−50−00−400−802.
D. Testing
(1) Remove rig pins from the elevator control system. Refer to Figure 3.
(2) Remove the tags and close the circuit breakers that follow:
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 28 of 35

### Page 32

LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
(3) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to IN. Refer to AMM 24−00−00−863−802:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
ENGINE L ENG IGN 1 BATT
ENGINE L ENG IGN 2 BATT
ENGINE R ENG IGN 1 BATT
ENGINE R ENG IGN 2 BATT
FLT CONTROL P FEEL/RUD LIM 1 DC 1
FLT CONTROL P FEEL/RUD LIM 2 DC ESS
FLT CONTROL RUDDER TRIM DC ESS
HYD HYD PUMP 1B AC 3
HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3B AC 1
HYD HYD PUMP 3A AC 4
(4) Do the functional test of the elevator control system. Refer to
AMM 27−31−00−720−801.
(5) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to OUT. Refer to AMM 24−00−00−863−801:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
FLT CONTROL P FEEL/RUD LIM 1 DC 1
FLT CONTROL P FEEL/RUD LIM 2 DC ESS
FLT CONTROL RUDDER TRIM DC ESS
HYD HYD PUMP 1B AC 3
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 29 of 35

### Page 33

HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3B AC 1
HYD HYD PUMP 3A AC 4
(6) Open and tag the circuit breakers that follow:
LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
E. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Install access panel for the elevator control bellcrank (345EL). Refer to
AMM 55−30−13−400−805.
(3) Install lower trailing−edge access−panels (352AB/362AB). Refer to
AMM 55−10−17−400−802.
(4) Install upper visors (346KL/346KR). Refer to AMM 55−10−05−400−809.
(5) Install lower visors (346JL/346JR). Refer to AMM 55−10−05−400−810.
(6) Remove the tags and close the circuit breakers that follow:
LOCATION CB NO. NAME ZONE
ACPC B6 STAB TRIM CH 1 252
CCBP E5 STAB TRIM CH 2 222
(7) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to IN. Refer to AMM 24−00−00−863−802:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
ENGINE L ENG IGN 1 BATT
ENGINE L ENG IGN 2 BATT
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 30 of 35

### Page 34

ENGINE R ENG IGN 1 BATT
ENGINE R ENG IGN 2 BATT
FLT CONTROL P FEEL/RUD LIM 1 DC 1
FLT CONTROL P FEEL/RUD LIM 2 DC ESS
FLT CONTROL RUDDER TRIM DC ESS
HYD HYD PUMP 1B AC 3
HYD HYD PUMP 2B AC 2
HYD HYD PUMP 3B AC 1
HYD HYD PUMP 3A AC 4
F. Recording
When any PART of this Service Bulletin is completed, make an entry in the aircraft
log and send the attached Incorporation Notice to Bombardier Business Aircraft
Customer Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
Kit 700K27−6503 is necessary to do PART B and contains the parts that follow:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
AN386−1−10 4 Tapered Pin AN386−1−10 Discard
AN386−1−11 4 Tapered Pin AN386−1−11 Discard
AN975−3 8 Washer AN975−3 Discard
MS17826−3 8 Nut MS17826−3 Discard
MS24665−73 6 Cotter Pin MS24665−73 Discard
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 31 of 35

### Page 35

NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
MS24665−132 8 Cotter Pin MS24665−132 Discard
MS24665−136 12 Cotter Pin MS24665−136 Discard
MS27646−41 4 Bearing MS27646−41 Discard
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
The parts that follow are necessary to do PART A of this Service Bulletin and are
available from Bombardier Aerospace Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
MS24665−136 4 Cotter Pin MS24665−136 Discard
NOTE: The part numbers for the items listed above are subject to change without
revision to this Service Bulletin. In case of discrepancy between this list
and any other list, the Illustrated Parts Catalog prevails and shall be used
to determine the latest part number.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Lacquer,
Gloss, For
Aircraft
A−A−3165,
Color Red
− As Necessary Code: A
Seal and Coat
Compound
Pro Seal
870B
MIL−PRF−81733,
Type II, Class 1,
Grade A
As Necessary Code: B
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 32 of 35

### Page 36

DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Seal and Coat
Compound
Pro Seal
870C
MIL−PRF−81733,
Type IV, Class 1,
Grade A
As Necessary Code: B
Brush, soft
bristled
− − As Necessary
For PART A
Code: C
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Tempo Paint and Varnish Co.
205 Fenmar Dr.
Weston, Ontario
M9L 2X4
Canada
Tel.: (416) 746−2233
Code: B
PRC−Desoto International
11601 United St..
Mojave, CA
USA, 93501−7048
Tel.: (661) 824−4532
Code: C
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 33 of 35

### Page 37

APPENDIX A — INFORMATION FEEDBACK SHEET
ELEVATOR TORQUE TUBE BEARING CHECK
Record the following aircraft information and send to:
tech.services.global.series@aero.bombardier.com
TABLE 1 - AIRCRAFT IDENTIFICATION
AIRCRAFT SERIAL NO. AIRFRAME HOURS AIRCRAFT CYCLES
TABLE 2 - SURFACE ANGLE DEFLECTION CHECK
CLINO L ANGLE CLINO R
24° ±0.5
0° ±0.5
19° ±0.5
TABLE 3 - VISUAL INSPECTION FOR SAND/DUST ACCUMULATION
1 Area overall
condition
Clean Accumulation of
sand/dust
2 Bearing and
torque tube
condition
Clean Accumulation of
sand/dust
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 34 of 35

### Page 38

APPENDIX A — INFORMATION FEEDBACK SHEET
TABLE 4 - INSPECTION FOR ABNORMAL BEARING STIFFNESS USING
POWERED FLIGHT CONTROLS/MARKINGS
BEARING POSITION PASS POTENTIALFRICTION POTENTIALLYSEIZED
LEFT
TOP
BOTTOM
RIGHT
TOP
BOTTOM
TABLE 5 - INSPECTION FOR ABNORMAL BEARING STIFFNESS USING
MANUAL ROTATION
BEARING POSITION NOTAPPLICABLE PASS BINDING/RATCHETING SEIZED
LEFT
TOP
BOTTOM
RIGHT
TOP
BOTTOM
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 23/2020
Revision 01: Dec 07/2020
700−27−6503
Page 35 of 35

### Page 39

700−27−6503 Rev. 01 Dec 07/2020
SPECIAL CHECK — ELEVATOR CONTROL SYSTEM —
INSPECTION OF TORQUE TUBE BEARINGS
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 40

SERVICE BULLETIN INCORPORATION SHEET − "700−27−6503"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−27−6503 01
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
