# Bombardier Service Bulletin 700-27-6509

Copy: Revision 01 ("700-27-6509 Rev01"), 35 pages: PDF https://openairdocs.org/files/sha256/9d/bd/9dbd4585d2a965a779891629f8f862cfebe4846f61c9ca4d5582b5dbdda0770d; text https://openairdocs.org/service-documents/bombardier/sb-700-27-6509/file/9dbd4585d2a9.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-2015; AD 2024-23-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-27-6509
- Latest revision known: 700-27-6509, Revision 01, dated May 5, 2023 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-27-6509

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-23-08](https://openairdocs.org/ad/2024-23-08.md), effective Jan 6, 2025: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-27-6509/proposed.md).

## Text (35 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-2015; AD 2024-23-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Basic Issue of this Service Bulletin dated Oct 04/2022, and replace in its
entirety with this Revision 01.
Service Bulletin No. 700−27−6509
Date of Basic Issue Oct 04/2022
Revision No. 01 Dated May 05/2023
This revision has no effect for aircraft on which the Basic Issue of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as "Not Applicable" for this revision.
This revision is issued to:
1. Add, in Paragraph 1., the Planning Information Note 3 and 4.
2. Change, in Paragraph 1.A., to revise the effectivity.
3. Change, in Paragraph 1.K., to revise the Modsum R700T400776 to Rev. B3.
4. Change, in Paragraph 1.K., to revise the Kit Drawing KGC991−1671 to Rev. B.
5. Change, in Paragraph 2.C., to delete Step (10).(a), and Step 19 as it is redundant.
6. Change, in Paragraph 2.C., to revise Steps (11).(a).(ii)., (15).(b)., (17).(b)., (27).(g).(ii).,
(27).(m)., and (28).(d).
7. Change, in Paragraph 2.C., to revise Step (30).(a)., and add a Note.
8. Change, in Paragraph 2.C., to add Step (34).
9. Revise Figure 10, to remove the laminated shim in Sheet 1.
10.Make miscellaneous minor changes, as necessary, with no change of context.
SERVICE BULLETIN
MODEL BD−700−1A10 (BD−700)
700−27−6509
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

SPECIAL CHECK/MODIFICATION – FLAP SYSTEM –
INSTALLATION OF IMPROVED INBOARD FLAP SEAL PLATE
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: Refer to Paragraph 1.A.
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subjected to an Airworthiness Directive which will
make it necessary to implement this Service Bulletin.
To place an order for kit, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−52
FLIGHT CONTROLS
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 1 of 1
This Service Bulletin is available at:

### Page 3

SPECIAL CHECK/MODIFICATION – FLAP SYSTEM –
INSTALLATION OF IMPROVED INBOARD FLAP SEAL PLATE
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. They can be reached at
bacs_isit@aero.bombardier.com. The parts will be allocated on a first
come first serve basis.
Should you require additional information, please contact your Regional
Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 700−00−6502.
3. Aircraft must be de−fueled to proceed with the inner flap seal plate rigging
upon re−installation of the seal plate. Operators are advised to make
necessary planning for de−fueling.
4. Kits 700K27−6509A or 700K27−6509B is required to do this Service
Bulletin. While both kits 700K27−6509A and 700K27−6509B are
equivalent and can be used to accomplish this Service Bulletin, kit
700K27−6509B consist of improved version alleviating the need for
trimming operation. Kit 700K27−6509B also include all required hardware
with extra quantities to ensure straightforward installation as opposed to kit
700K27−6509A that only include the non standard hardware.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 27−52
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2022−2023 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 1 of 31
This Service Bulletin is available at:

### Page 4

A. Effectivity
BD−700−1A10 aircraft, Serial No. 9861, 9872, 60001 to 60101.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
The intent of this Service Bulletin was met on the aircraft that follow with the
Pre−Published Service Bulletin 700−27−6509 listed below:
AIRCRAFT SERIAL NO. PRE_PUBLISED DATE
60077 Aug 20/2022
B. Reason
1. Condition:
There have been reports of cracked inner flap seal plate attachment angles
which could allow the seal plate to detach.
2. Objective/Benefit:
This Service Bulletin instructs to replace both (LHS and RHS) existing inner flap
seal plate assembly with an improved one.
C. Description
This Service Bulletin gives instructions in PART A to:
− Get access to the inner flap seal plate,
− Inspect the seal plate assembly for cracks,
(i) If cracks are found, do PART B of this Service Bulletin, or contact
Bombardier via SRPSA for alternative solution.
(ii) If no cracks are found, operators may defer retrofit up to 18 months with
repeat inspections every 250 flight hours (or) do PART B of this Service Bulletin.
This Service Bulletin gives instructions in PART B to:
− Install the new inner flap seal plate assembly.
D. Compliance
Recommended to inspect within 250 flight hours from this Service Bulletin release
date (Basic Issue).
However for the aircraft with more than 750 flight hours from this Service Bulletin
release date (Basic Issue), must do the initial inspection within 100 flight hours.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 2 of 31

### Page 5

During inspection, if cracks are found in the inner flap seal plate, improved
assembly should be installed per PART B. If it is not possible, alternative repair
solution can be provided via SRPSA.
If no cracks are found during inspection, operator may defer installation of improved
assembly (PART B) up to 18 months from this Service Bulletin release date (Basic
Issue), with repeat inspections every 250 flight hours.
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin. Standard
SRPSA fees may apply. Refer to the Services section of the Bombardier
customer portal for the latest prices, rates and fees.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−6502.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the labor man−hours and should be considered
for planning purposes before you schedule this Service Bulletin.
1 man−hour is necessary to do PART A of this Service Bulletin on LHS and RHS.
23 man−hours are necessary to do PART B of this Service Bulletin.
Bombardier Aviation does not pay for the labor to do PART A of this Service
Bulletin.
The labor required to do PART B of this Service Bulletin is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 3 of 31

### Page 6

− this Service Bulletin is scheduled within 18 months from this Service Bulletin
release date (Basic Issue).
G. Material − Cost and Availability
Kit 700K27−6509A (or) 700K27−6509B is necessary to do PART B of this Service
Bulletin. For material data, refer to Paragraph 3.C.
KIT NO. PRICE
700K27−6509A
(OR)
700K27−6509B
Please contact Bombardier Aviation Parts Services, in
Montreal, for delivery lead times and confirmation of prices.
The kit is available at no cost if:
− a no−charge purchase order is sent to Bombardier Aviation within 18 months
from this Service Bulletin release date (Basic Issue).
Smart Parts does not pay for this recommended Service Bulletin at any time.
H. Tooling
The equipment and tools listed below are necessary to do this modification.
GSE REFERENCE NO. PART NO. DESCRIPTION
20X−10−01 − Tag, Circuit Breaker (Red Ring)
Commercially Available − Grip Measurement Gauge
Commercially Available − NAS1789 Nut Plate Drill Jig
Commercially Available − Rivet Installation Tools
Commercially Available − Torque Wrench
NOTES: 1. Refer to the Global 6500 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
2. Refer to the Liability Statement in the ITEM for the Global 6500 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 4 of 31

### Page 7

I. Weight and Balance
WEIGHT MOMENT
+1.62 lbs (0.74 kg) 1255.8 lbs−in (14.47 kgm)
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive, (pending).
− Bombardier Aviation, Modification Summary R700T400776, Rev. B3 .
− Bombardier Aviation, Kit Drawing KGC991−1671, Rev. B .
− Global 6500 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 20, 24
and 27.
− Global 6500 BD−700 Aircraft Illustrated Parts Catalog (AIPC), Chapter 27.
− Global 6500 BD−700 Structural Repair Manual (SRM), Chapter 51.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapters 20 and 51.
L. Other Publications Affected
− Global 6500 BD−700 Aircraft Maintenance Manual (AMM), Chapter 27.
− Global 6500 BD−700 Aircraft Illustrated Parts Catalog (AIPC), Chapter 27.
M. Equivalent Service Bulletin
− For the Global 5500 BD−700−1A11 aircraft, use SB 700−27−5509.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6500
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6500 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all flight control safety precautions. Refer to AMM 27−00−00−910−801.
(3) Connect electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(4) Set the SLAT/FLAP control lever to OUT/30°.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 5 of 31

### Page 8

(5) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(6) In the flight compartment, on the EMS CDU, set the circuit breaker that follows
to LOCKED. Refer to AMM 24−00−00−863−801.
For the left inner flap panel:
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
FLT CONTROLS SLAT/FLAP CTLR 1 BATT
For the right inner flap panel:
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
FLT CONTROLS SLAT/FLAP CTLR 2 DC ESS
(7) Open and tag the circuit breaker that follows:
For the left inner flap panel:
LOCATION CB NO. NAME ZONE
CCBP G9 SLAT/FLAP PWR 1 222
For the right inner flap panel:
LOCATION CB NO. NAME ZONE
CCBP E2 SLAT/FLAP PWR 2 222
B. PART A — Inspection of Inboard Flap Seal Plate
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
Do the procedure that follows for the LHS and RHS flap.
(1) Inspect the stiffeners, Part No. GM147−2355−1/−2, for cracks. Refer to
Figure 1.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 6 of 31

### Page 9

(2) Do a Detail Visual Inspection (DVI) of inner flap seal plate assembly attaching
angles (GM147−2355−1/−2, GM147−2355−3/−4 and GM147−2352) to make
sure that there is no visual crack. Refer to Figure 1.
NOTE: Any other type of damage would consist of valid findings and should
be reported to Bombardier for further advise.
(a) If cracks are found, do as follows:
(i) Do PART B of this Service Bulletin,
or
(ii) Contact Bombardier via SRPSA to get an alternative repair solution.
(b) If no cracks are found, do as follows:
(i) Operators may defer PART B up to 18 months from this Service
Bulletin release date (Basic Issue), with repeat inspections every
250 flight hours,
or
(ii) Do PART B of this Service Bulletin.
SB700−27−6509_023
Inspection of Inner Flap Seal Plate Assembly
Figure 1
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 7 of 31

### Page 10

C. PART B — Replacement of Inboard Flap Seal Plate
NOTES: 1. If it is not possible to complete all the instructions in this Service
Bulletin because of the configuration of the aircraft, submit an SRPSA
for analysis and to get an approved disposition to complete this
Service Bulletin.
2. Touch−up all the fasteners per finish code X186. Refer to
SRM 51−01−04.
Do the procedure that follows on the LHS flap.
(1) Remove and retain the existing inner flap seal plate. Refer to
AMM 27−52−17−000−801.
(2) Remove and discard the stiffeners, Part No. GM147−2355−1/−2. Refer to
Figure 2.
(3) Remove the P−seal, Part No. GM147−2529, from the trailing edge of end rib
as follows. Refer to Figure 2.
(a) Remove the nuts, Part No. NAS1291C08M (qty 12), washers, Part
No. NAS1149CN816R (qty 11), filler, Part No. GM148−3001−21, screws,
Part No. NAS1102V08−8 (qty 12), shims, Part No. S5324−63−90−296
(Qty 2), laminated shims, Part No. S10249−63−0−296 (Qty 1), and the
P−seal, Part No. GM147−2529.
(b) Retain the filler, Part No. GM148−3001−21, shims, Part
No. S5324−63−90−296 (Qty 2), laminated shims, Part
No. S10249−63−0−296 (Qty 1), and the P−seal, Part No. GM147−2529.
(c) Discard the nuts, Part No. NAS1291C08M (qty 12), washers, Part
No. NAS1149CN816R (qty 11), and the screws, Part No. NAS1102V08−8
(qty 12).
(4) Remove and discard the clip assembly, Part No. GM141−3331, and the
attaching screws, Part No. NAS1580V3T4 (qty 4), from the trailing edge of end
rib. Refer to Figure 2.
(5) Remove the sealant residues from both upper and lower areas of the trailing
edge of end rib. Refer to SPM−MM 51−23−00−100−801 and Figure 2.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 8 of 31

### Page 11

SB700−27−6509_021
NOTE
1 Retain for re−use.
1
1
Figure 2
(6) Do a Detail Visual Inspection (DVI) of flap inboard closing rib and trailing edge
for damage.
(7) Perform an Eddy Current Inspection of flap inboard closing rib holes (qty 6)
common to the OUTBD stiffener, Part No. GM147−2355−1/−2, and angle, Part
No. GM147−2352 per NDTM Part 1 Section 6E to make sure no cracks are
running out of rib holes. It is acceptable to use Liquid Penetrant Inspection per
NDTM Part 1 Section 8 in lieu of Eddy Current Inspection. Refer to Figure 3.
(8) If any damages are found in the inspection, contact Bombardier via SRPSA for
alternative solution.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 9 of 31

### Page 12

RIB HOLES
(QTY 6)
FLAP CLOSING INBOARD RIB
SB700−27−6509_022
Inspection of Inboard Flap Closing Rib
Figure 3
(9) Position the bracket assembly, Part No. KGC991−1675. Refer to Figure 10,
Detail B and D.
(10) Attach OUTBD stiffener, Part No. KGC991−1672, to the flap end rib with
screws, Part No. MS27039−1−10 (qty 2) and washers, Part
No. B0202013−1328−32 (qty 2). Refer to Figure 4 and Figure 10, Detail B.
(a) Make sure that the OUTBD stiffener, Part No. KGC991−1672, is
positioned parallel to the lower surface of the flap.
(b) Hand tighten the screws, Part No. MS27039−1−10 (qty 2).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 10 of 31

### Page 13

SB700−27−6509_011
A
A
A−A
BRACKET ASSY
SKIN SURFACE
STIFFENER
Figure 4
(11) Attach the bracket assembly, Part No. KGC991−1675, to the OUTBD stiffener,
Part No. KGC991−1672, with screws, Part No. MS27039−1−10 (qty 2) and
washers, Part No. B0202013−1328−32 (qty 2). Refer to Figure 4 and
Figure 10, Detail B.
(a) If bracket assembly, Part No. KGC991−1675−1S/−2S is used, do as
follows:
(i) Trim the lower flange edge to 0.940 in (23.88 mm), and create
chamfer to clear interference with trailing edge closing rib.
(ii) Touch−up  trimmed edge per finish code A032 (Grey No. 16473).
Refer to SRM 51−01−04.
(iii) Identify the bracket assembly as KGC991−1671−9/−10 respectively.
(b) Make sure that the bracket assembly, Part No. KGC991−1675, makes
uniform contact with the inner surface of the lower and upper skins.
(c) Hand tighten the screws, Part No. MS27039−1−10 (qty 2).
(12) Transfer the holes (qty 4), from the flap lower skin onto the bracket assembly,
Part No. KGC991−1675. Refer to Figure 10, Detail B.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 11 of 31

### Page 14

(13) Transfer the holes (qty 3), from the flap upper skin onto the bracket assembly,
Part No. KGC991−1675. Refer to Figure 10, Detail B.
(14) Disassemble the OUTBD stiffener, Part No. KGC991−1672, and the bracket
assembly, Part No. KGC991−1675, from the flap. Refer to Figure 10, Detail B.
(15) Open the holes (qty 4), transferred onto the lower flange of bracket assembly,
Part No. KGC991−1675, to a diameter of 0.195 to 0.201 in (4.95 to 5.11 mm).
Refer to Figure 10, Detail D.
(a) Make sure that a minimum 2D edge distance is maintained.
(b) Touch−up exposed areas of the holes per finish code A028. Refer to
SRM 51−01−04.
(16) Install the nut plates, Part No. MS21059L3 (qty 4), with rivets, Part
No. MS20426AD3−5S (qty 8), on the lower flange of bracket assembly, Part
No. KGC991−1675. Refer to SRM 51−42−08.
(17) Open the holes (qty 3), transferred onto the upper flange of bracket assembly,
Part No. KGC991−1675, to a diameter of 0.195 to 0.201 in (4.95 to 5.11 mm).
Refer to Figure 10, Detail B and D.
NOTE: Holes in the upper trailing edge skin to remain in original size.
(a) Make sure that a minimum 2D edge distance is maintained.
(b) Touch−up exposed areas of the holes per finish code A028. Refer to
SRM 51−01−04.
(18) Install the nut plates, Part No. NAS1789−08 (qty 3), with rivets, Part
No. MS20426AD3−6S, on the upper flange of bracket assembly, Part
No. KGC991−1675. Refer to SRM 51−42−08.
(19) Rework the P−seal, Part No. GM147−2529, as follows. Refer to Figure 10,
Detail G and H.
(a) Position the P−seal, Part No. GM147−2529, onto the upper flange of the
bracket assembly, Part No. KGC991−1675 using the new holes (qty 3).
(b) Mark the location of the bosses (qty 3), per best shop practice.
(c) Trim the P−seal, Part No. GM147−2529, as necessary.
(d) Make sure that the reworked P−seal, Part No. GM147−2529, fits with the
upper flange of the bracket assembly, Part No. KGC991−1675.
(e) Touch−up exposed metal edge per finish code X055. Refer to
SRM 51−01−04.
(f) Identify the reworked P−seal as KGC991−1671−3/−4.
(20) Apply faying surface sealant to the lower flange and upper bosses of the
bracket assembly, Part No. KGC991−1675. Refer to SRM 51−23−04, and
Figure 10, Detail B and E.
(21) Install the bracket assembly, Part No. KGC991−1675. Refer to Figure 10,
Detail B and E.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 12 of 31

### Page 15

(22) Wet install the screws, Part No. NAS1580V3T4 (qty 4), at the bottom of the
bracket assembly, Part No. KGC991−1675. Refer to SRM 51−23−04 and
51−41−04, and Figure 10, Detail B.
(23) Torque the screws, Part No.  NAS1580V3T4, from 20 to 25 lbf in (2.26 to
2.82 Nm). Refer to SPM−MM 20−21−00−910−801.
(24) Install the P−seal, Part No. KGC991−1671, and wet install screws, Part
No. NAS1102V08−8 (qty 9), washer, Part No. NAS1149CN816R (qty 8), filler,
Part No. GM148−3001−21, nuts, Part No. NAS1291C08M (qty 9) , and the
screws, Part No. NAS1102V08−10 (qty 3). Refer to SRM 51−23−04 and
51−41−04, and Figure 10, Detail B and E.
(25) Torque the screws, Part No.  NAS1102V08, from 20 to 25 lbf in (2.26 to
2.82 Nm). Refer to SPM−MM 20−21−00−910−801.
(26) Apply CIC on and around the bottom leg of the bracket assembly, Part No.
KGC991−1675. Refer to SRM 51−27−16 and Figure 10, Detail E.
(27) Rework the seal plate, Part No. GM147−2351, as follows. Refer to Figure 5.
(a) Remove and discard the existing stiffener, Part No. GM147−2355−3/−4.
(b) Remove and discard existing bracket, Part No. GM147−2352.
(c) Remove the sealant residues and clean the seal plate, Part
No. GM147−2351. Refer to SPM−MM 51−23−00−100−801.
(d) Do a Detail Visual Inspection (DVI) of the seal plate, Part
No. GM147−2351, and make sure that there are no damages.
(e) Make sure that the stainless steel seal, Part No. GM147−2367, is trimmed
as shown in Figure 5.
(f) If the stainless steel seal, Part No. GM147−2367, is not trimmed, do as
follows:
(i) Trim the stainless steel seal, Part No. GM147−2367−1/−2, as shown
in Figure 5.
(ii) Touch−up exposed metal edge per finish code X070 and apply
topcoat paint (Gray No. 16473). Refer to SRM 51−01−04.
(iii) Re−identify the stainless steel seal as GM148−2095R16231401 /
GM148−2095R16231402.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 13 of 31

### Page 16

SB700−27−6509_017
GM147−2355−3/−4
(STIFFENER)
GM147−2351
(SEAL PLATE)
PRE MOD
GM147−2352
(BRACKET)
GM147−2367
(SEAL)
MAKE SURE THAT VERSION OF
GM147−2367 SEAL HAS THE
HATCHED AREA TRIMMED
OR ABSENT
.67 ± .03
.08 ± .03
1.38 ± .03
2.33 ± .03
2.56 ± .03
90.0°
R 34.0
R .6
R .125
(.54 ± .03)
GM147−2367−1
GM147−2367−2
Figure 5
(g) Position INBD stiffener, Part No. KGC991−1673 onto the seal plate, Part
No. KGC991−1671, and align the 3 pilot holes with the existing seal plate
rivet holes. Refer to Figure 6.
(i) If using stiffener KGC991−1673−1S/2S, rework clearance holes as
shown in Figure 10, Detail J.
(ii) Touch−up exposed holes per finish code A032 (White No. 17875).
Refer to SRM 51−01−04.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 14 of 31

### Page 17

(iii) Re−identify the stiffener as KGC991−1671−7/8.
SB700−27−6509_012
PILOT HOLE
Figure 6
(h) Transfer all the existing holes (qty 18) of the seal plate, Part
No. GM147−2351, onto the INBD stiffener, Part No. KGC991−1673, and
open holes to final diameter and countersink to fit the fastener. Refer to
Figure 7.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 15 of 31

### Page 18

SB700−27−6509_013
LEGEND
MS20426AD4−6S (PRE−MOD LOCATION)
MS20426AD5−6S (PRE−MOD LOCATION)NOTE
1 An edge distance of 1.7D is permissible at qty 3 MS20426AD5 locations.
1
Figure 7
(i) Position and open the 6 new holes to their final size on the upper row of
the seal plate, Part No. GM147−2351. Make sure that a minimum of 2D
edge distance and 4D pitch is maintained. Refer to Figure 8.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 16 of 31

### Page 19

SB700−27−6509_014
LEGEND
MS20426AD4−6S (NEW LOCATION)
MS20426AD5−6S (NEW LOCATION)
MS20426AD4−6S
(RIVET)
MS20426AD5−6S
(RIVET)
NOTE
1 An edge distance of 1.7D is permissible at qty 3 MS20426AD5 locations.
1
Figure 8
(j) Transfer the holes (qty 12), from the INBD stiffener, Part
No. KGC991−1673, to the seal plate and open holes to final diameter and
countersink on each side (double flush) to fit the fastener. Refer to
Figure 9.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 17 of 31

### Page 20

SB700−27−6509_015
MS20426AD5−7S
(RIVET)
(12 PLACES)
LEGEND
MS20426AD5−7S (NEW LOCATION)
Figure 9
(k) Disassemble the INBD stiffener, Part No. KGC991−1673, and the seal
plate.
(l) Debur the reworked areas in the INBD stiffener, Part No. KGC991−1673,
and the seal plate.
(m) Touch−up exposed areas of the holes per finish code A028. Refer to
SRM 51−01−04.
(n) With solvent clean the reworked areas. Refer to
SPM−MM 51−25−00−110−801.
(o) With faying surface sealant, assemble the INBD stiffener, Part
No. KGC991−1673, on the seal/seal plate assembly, Part
No. GM147−2351, and wet install the rivets, Part No. MS20426AD5−6S
(qty 6), MS20426AD4−6S (qty 15), MS20426AD5−6S (qty 3), and
MS20426AD5−7S (qty 12). Refer to SRM 51−23−04 and 51−42−08, and
Figure 10, Detail B, C and F.
(p) Apply aerodynamic seal at the lower edge of INBD stiffener, Part
No. KGC991−1673. Refer to SRM 51−14−04 and Figure 10, Detail E.
(q) Apply one layer of fluid resistant polyurethane topcoat on the INBD
stiffener, Part No. KGC991−1673, to match the customer paint scheme
per finish code X010. Refer to SRM 51−01−04 and Figure 10, Detail E
and F.
(r) Re−identify the seal plate as KGC991−1671−5/−6.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 18 of 31

### Page 21

(28) Assemble the OUTBD stiffener, Part No. KGC991−1672, as follows. Refer to
Figure 10, Detail B and F.
(a) Position the A−Nut plate assembly, Part No. KGC991−1674 (qty 3), onto
the OUTBD stiffener, Part No. KGC991−1672, transfer the pilot holes and
open the holes to its final size.
NOTE: Attaching hardware can be used to position the A−nut plate
assembly and the OUTBD stiffener. Refer to Figure 10, Detail B
and F.
(b) Disassemble the A−Nut plate assembly, Part No. KGC991−1674.
(c) Debur the reworked areas in the OUTBD stiffener, Part
No. KGC991−1672.
(d) Touch−up exposed areas of the holes/edge trimming per finish code
A028. Refer to SRM 51−01−04.
(e) With solvent clean the reworked areas. Refer to
SPM−MM 51−25−00−110−801.
(f) With faying surface sealant, assemble the A−Nut plate assembly, Part
No. KGC991−1674−1 (qty 3), on the OUTBD stiffener, Part
No. KGC991−1672, and wet install the rivets, Part No. MS20426AD4−5S
(qty 9). Refer to SRM 51−23−04 and 51−42−08, and Figure 10, Detail B
and D.
(g) Apply one layer of fluid resistant polyurethane topcoat on the OUTBD
stiffener, Part No. KGC991−1672, to match the customer paint scheme
per finish code X010. Refer to SRM 51−01−04 and Figure 10, Detail E
and F.
(29) Install the OUTBD stiffener assembly, Part No. KGC991−1672, on the flap end
rib with washers, Part No. B0202013−1328−32 (qty 7), and the screws, Part
No. MS27039−1−10 (qty 7). Refer to SRM 51−41−04 and Figure 10, Detail B.
(a) Hand tighten the screws, Part No. MS27039−1−10 (qty 7).
(30) Install the seal plate assembly, Part No. KGC991−1671, on the flap end rib
with screws, Part No. MS27039−1−14 (qty 3) and MS27039−0814 (qty 3), and
washers, Part No. NAS1149D0332K (qty 3), and NAS1149DN832K (qty 3).
Refer to SRM 51−41−04 and Figure 10, Detail B.
NOTE: It is acceptable for the screw, Part No. MS27039−0814 (qty 3), to
contact the p−seal, Part No. KGC991−1671−3/−4, when installed.
Refer to Figure 10, Detail C.
(a) Align lower surface of the stiffener, Part No. KGC991−1673, as best as
possible with flap lower skin.
NOTE: Seal plate rigging will define the final position.
(b) Install the shims, Part No. S5324−63−90−296 (Qty 2), and laminated
shims, Part No. S10249−63−0−296 (Qty 1).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 19 of 31

### Page 22

(i) It is permissible to re−use the shim previously installed at the FWD
location.
(c) Hand tighten the screws, Part No. MS27039−1−14 (qty 3) and
MS27039−0814 (qty 3).
(31) Align the fastener holes (qty 12) in the bottom end of INBD and OUTBD
stiffeners, and Install the screws, Part No. MS27039−1−10 (qty 12), and the
washers, Part No. NAS1149C0316R (qty 12). Refer to SRM 51−41−04 and
Figure 10, Detail B.
(a) Adjust the seal plate assembly in the most outboard position for it to be rig
at later time.
(b) Hand tighten the screws, Part No. MS27039−1−10 (qty 12).
(32) Repeat the above steps for the RHS flap.
(33) Do the rigging of the inner flap seal plate. Refer to AMM 27−52−17−820−801.
(a) Install and adjust or combine the shims, Part No. S10249−63−90−320B
(qty 1), S5324−63−90−320C20 (qty 2), S5324−63−90−382C20 (qty 2),
and S10249−63−90−382B (qty 1), at the forward and aft flanges to attain
the rigging requirements. Refer to Figure 10, Detail B, E and F.
(i) It is permissible to use the existing shim at the FWD position.
(b) Target the highest tolerance value for the gap, to avoid contact.
(c) Complete the installation by torquing all the fasteners to proper torque
value.
(34) Verify and make sure that the gap between the inner flap seal plate, Part
No. KGC991−1673, and the outboard stiffener, Part No. KGC991−1672, is
0.060 in (1.52 mm). Refer to Figure 10, Detail D.
(a) If necessary, trim the edge of stub fairing, Part No. GM147−0361, until the
required gap is met.
(b) Deburr the sharp edges and touch−up exposed areas of the edge
trimming per finish code A032. Refer to SRM 51−01−04.
(c) Re−identify the stub fairing, Part No. GM147−0361/−1/−2 as
KGC991−1671−11/−12.
(d) Re−identify the stub fairing, Part No. GM147−0361/−3/−4 as
KGC991−1671−13/−14.
D. Testing
No testing is required.
E. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) In the flight compartment, on the EMS CDU, set the circuit breaker that follows
to IN. Refer to AMM 24−00−00−863−802.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 20 of 31

### Page 23

For the left inner flap panel:
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
FLT CONTROLS SLAT/FLAP CTLR 1 BATT
For the right inner flap panel:
SYSTEM NAME CIRCUIT BREAKER NAME BUS NAME
FLT CONTROLS SLAT/FLAP CTLR 2 DC ESS
(3) Remove and tag and close the circuit breaker that follows:
For the left inner flap panel:
LOCATION CB NO. NAME ZONE
CCBP G9 SLAT/FLAP PWR 1 222
For the right inner flap panel:
LOCATION CB NO. NAME ZONE
CCBP E2 SLAT/FLAP PWR 2 222
(4) Connect electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(5) Set the SLAT/FLAP control lever to IN/0°.
(6) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(7) Remove the warning placard from the SLAT/FLAP lever.
F. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin is completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 21 of 31

### Page 24

3. MATERIAL INFORMATION
A. Kit
Kit 700K27−6509A (or) 700K27−6509B is necessary to do PART B of this Service
Bulletin.
1. Kit 700K27−6509A contains the parts that follow:
NOTE: This kit does not contain the rivets, Part No. MS20426AD3−5S,
MS20426AD3−6S, MS20426AD4−6S, MS20426AD5−6S, and
MS20426AD5−7S. They must be procured locally.
NEW PART NO. QTY ITEM
USED
PART
NO.
INSTRUCTIONS
-
DISPOSITION
B0202013−1328−32 14 Washer, LargeOD − −
KGC991−1672−1S 1 Kit, OUTBDStiffener, LHS − −
KGC991−1672−2S 1 Kit, OUTBDStiffener, RHS − −
KGC991−1673−1S 1 Kit, INBDStiffener, LHS − −
KGC991−1673−2S 1 Kit, INBDStiffener, RHS − −
KGC991−1674−1 6 Kit, A−Nut PlateAssy − −
KGC991−1675−1S 1 Kit, Attach BRKTAssy, LHS − −
KGC991−1675−2S 1 Kit, Attach BRKTAssy, RHS − −
MS21059L3 10 Nut Plate − −
MS27039−0814 6 Screw, PANHead − −
MS27039−1−10 42 Screw, PANHead − −
MS27039−1−14 10 Screw, PANHead − −
NAS1102V08−10 6 Screw, Flat Head − −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 22 of 31

### Page 25

NEW PART NO. QTY ITEM
USED
PART
NO.
INSTRUCTIONS
-
DISPOSITION
NAS1102V08−8 24 Screw, Flat Head − −
NAS1149C0316R 30 Washer − −
NAS1149CN816R 24 Washer − −
NAS1149D0332K 10 Washer − −
NAS1149DN832K 10 Washer − −
NAS1291C08M 24 Nut − −
NAS1580V3T4 10 Screw, Flat Head − −
NAS1789−08 8 Nut Plate − −
S10249−63−90−320B 2 Shim, Laminated − −
S10249−63−90−382B 2 Shim, Laminated − −
S5324−63−90−320C20 4 Shim, Solid − −
S5324−63−90−382C20 4 Shim, Solid − −
2. Kit 700K27−6509B contains the parts that follow:
NEW PART NO. QTY ITEM
USED
PART
NO.
INSTRUCTIONS
-
DISPOSITION
B0202013−1328−32 18 Washer, LargeOD − −
KGC991−1672−1S 1 Kit, OUTBDStiffener, LHS − −
KGC991−1672−2S 1 Kit, OUTBDStiffener, RHS − −
KGC991−1673−3S 1 Kit, INBDStiffener, LHS − −
KGC991−1673−4S 1 Kit, INBDStiffener, RHS − −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 23 of 31

### Page 26

NEW PART NO. QTY ITEM
USED
PART
NO.
INSTRUCTIONS
-
DISPOSITION
KGC991−1674−1 6 Kit, A−Nut PlateAssy − −
KGC991−1675−5S 1 Kit, Attach BRKTAssy, LHS − −
KGC991−1675−6S 1 Kit, Attach BRKTAssy, RHS − −
MS20426AD3−5S 40 Rivet, CSK − −
MS20426AD3−6S 20 Rivet, CSK − −
MS20426AD4−6S 60 Rivet, CSK − −
MS20426AD5−6S 30 Rivet, CSK − −
MS20426AD5−7S 30 Rivet, CSK − −
MS21059L3 10 Nut Plate − −
MS27039−0814 10 Screw, PANHead − −
MS27039−1−10 42 Screw, PANHead − −
MS27039−1−14 10 Screw, PANHead − −
NAS1102V08−10 10 Screw, Flat Head − −
NAS1102V08−8 24 Screw, Flat Head − −
NAS1149C0316R 30 Washer − −
NAS1149CN816R 24 Washer − −
NAS1149D0332K 10 Washer − −
NAS1149DN832K 10 Washer − −
NAS1291C08M 24 Nut − −
NAS1580V3T4 10 Screw, Flat Head − −
NAS1789−08 8 Nut Plate − −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 24 of 31

### Page 27

NEW PART NO. QTY ITEM
USED
PART
NO.
INSTRUCTIONS
-
DISPOSITION
S10249−63−90−320B 2 Shim, Laminated − −
S10249−63−90−382B 2 Shim, Laminated − −
S5324−63−90−320C20 4 Shim, Solid − −
S5324−63−90−382C20 4 Shim, Solid − −
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
No parts required.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
They can be purchased from a local supplier. Bombardier Aviation does not pay for
these consumables.
DESCRIPTION
PART
NO.
/NAME
SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Corrosion−Inhibiting
Compound Type II
(Thixotropic)
Dinitrol AV−30
− MIL−PRF−16173 As Necessary Code: A
Corrosion−Inhibiting
Compound Type III
(Ultra−Thin)
Dinitrol AV−ACF 50
− MIL−C−81309 As Necessary Code: A
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 25 of 31

### Page 28

DESCRIPTION
PART
NO.
/NAME
SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Corrosion−Inhibiting
Compound Type IV
(Heavy Duty Super
Penetrating)
Dinitrol AV−15
(Acceptable
Alternative to
Types I and II)
− MIL−PRF−16173 As Necessary Code: A
Corrosion−Inhibiting
Compound Type V
(Ultra−Thin Heavy
Duty Super
Penetrating)
Cor−Ban 23
(acceptable
alternative to Types
I, II or IV), CA
− − As Necessary Code: B
Primer, 44GN072
(base) /
44GN072CAT
(catalyst) / distilled
or deionized water
(reducer)
− BAMS 565−001 As Necessary Code: C
Primer, 620H
Series (Base) / 620
C Series Ctalyst)
− BAMS 565−002 As Necessary Code: D
Masking Tape
(Scotch 250) − − As Necessary Code: E
Sealing and
Coating
Compound,
Corrosion Inhibitive
Polysulfide Rubber,
Chromate
(Pro−Seal 870
CL B)
− MIL−DTL−81706,Class 1A As Necessary Code: E
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 26 of 31

### Page 29

DESCRIPTION
PART
NO.
/NAME
SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Sealing and
Coating
Compound,
Corrosion Inhibitive
Polysulfide Rubber,
Chromate
(Pro−Seal 870
CL C)
−
MIL−PRF−81733,
Type II, Class 1,
Grade A
As Necessary Code: E
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Lear Chemical Research Corp
6182A, Kestrel Road
Missisauga
ON
L5T 1Z2.
USA.
www.learchem.com
Code: B
Zip Chem Commercial
2 Bordon Trading Estate Old Station
way,
Bordon, Hampshire
GU35 9HH.
UK.
www.zipchem.com
Code: C
PRC Desoto International inc.
(DBA PPG Aerospace)
17451 Von Karman Ave
Irvine
CA
96214−6205
USA.
www.ppgaerospace.com
Code: D
Tristar Coatings Ltd
18 Cadetta Rd
Brampton
ON
L0P0X.
Canada.
www.tristarcoatings.ca
Code: E
Commercially Available
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 27 of 31

### Page 30

D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 28 of 31

### Page 31

KGC991−1673−1/−3 (LH)
KGC991−1673−2/−4 (RH)
(INBD STIFFENER)
KGC991−1671−5 (LH)
KGC991−1671−6 (RH)
(SEAL/SEAL PLATE SUB−ASSY)
MS27039−0814
(SCREW)
(3 PLACES)
NAS1149D0332K
(WASHER)
(3 PLACES)
MS27039−1−14
(SCREW)
(3 PLACES)
MS27039−1−10
(SCREW)
(7 PLACES)
S5324−63−90−382C20
(SOLID SHIM)
S10249−63−90−382B
(LAMINATED SHIM)
KGC991−1672−1 (LH)
KGC991−1672−2 (RH)
(OUTBD STIFFENER)
KGC991−1674−1 (LH)
A−NUT PLATE ASSY
(3 PLACES)
MS27039−1−10
(SCREW)
(12 PLACES)
NAS1149C0316R
(WASHER)
(12 PLACES)
NAS1580V3T4
(SCREW)
(4 PLACES)
S10249−63−90−320B
(LAMINATED SHIM)
WS47.80
(LH SHOWN, RH SIMILAR)
WS178.00
SB700−27−6509_001
KGC991−1671−3 (LH)
KGC991−1671−4 (RH)
(MODIFIED P−SEAL)
NAS1149CN816R
(WASHER)
(8 PLACES)
NAS1102V08−8
(SCREW)
NAS1291C08M
(NUT)
(8 PLACES)
NAS1291C08M
(NUT)
KGC991−1675−1/−5 (LH)
KGC991−1675−2/−6 (RH)
(BRACKET ASSY)
NAS1149DN832K
(WASHER)
(3 PLACES)
B0202013−1328−32
(WASHER)
(7 PLACES)
NAS1102V08−8
(SCREW)
(8 PLACES)
NAS1102V08−10
(SCREW)
(3 PLACES)
S5324−63−90−320C20
(SOLID SHIM)S5324−63−90−320C20
(SOLID SHIM)
GM148−3001−21
(FILLER)
NOTES
1
2
Permissible to use the original ones.
If filler is not available, it is permissible to use washer NAS1149CN816R as a substitute.
1
1 1
2
MODEL BD−700−1A10 (BD−700)
Installation of Improved Inboard Flap Seal Plate
Figure 10 (Sheet 1 of 3)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 29 of 31

### Page 32

SB700−27−6509_002
LEGEND
MS20426AD4−6S (NEW LOCATION)
MS20426AD5−6S (NEW LOCATION)
MS20426AD5−7S (NEW LOCATION)
MS20426AD4−6S (PRE−MOD LOCATION)
MS20426AD5−6S (PRE−MOD LOCATION)
NOTES
4
5
At six rivet locations 1.7 times of diameter edge distance is permissible.
Acceptable for hardware to contact P−seal when installed.
At three fastener hole locations on the top of the trailing edge, line up bracket assy and transfer locations onto the
KGC991−1671−5 (LH)
KGC991−1671−6 (RH)
(SEAL/SEAL PLATE SUB−ASSY)
KGC991−1673−1/−3 (LH)
KGC991−1673−2/−4 (RH)
(INBD STIFFENER)
KGC991−1675−1/−5 (LH)
KGC991−1675−2/−6 (RH)
(BRACKET ASSY)
MS20426AD5−7S
(RIVET)
(12 PLACES)
MS20426AD4−6S
(RIVET)
(15 PLACES)
MS20426AD5−6S
(RIVET)
(3 PLACES)
MS27039−0814
(SCREW)
(3 PLACES)MS20426AD5−6S
(RIVET)
(6 PLACES)
top flange. Drill holes into bracket assy only at these locations to diameter of 0.195 to 0.201 in (4.95 to 5.11 mm).
3
3
4
5
MS20426AD4−6S
(RIVET)
(9 PLACES)
6 Trim stub fairing as shown to get a clearance of 0.060 in ± 0.010 in (1.52 mm ± 0.25 mm) seal plate inboard 
and outboard stiffeners with flap in stowed position to avoid fouling condition with stiffeners.
6
1.32 in (33.53 mm)
(REF)
GM147−0361
(STUB FAIRING)
(REF)
Re−identify LH/RH stub fairing Part No. GM147−0361−1/−2 as KGC991−1671−11/−12 and7
GM147−0361−3/−4 as KGC991−1671−13/−14.
7
MODEL BD−700−1A10 (BD−700)
Installation of Improved Inboard Flap Seal Plate
Figure 10 (Sheet 2 of 3)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 30 of 31

### Page 33

KGC991−1671−5 (LH)
KGC991−1671−6 (RH)
(SEAL/SEAL PLATE SUB−ASSY)
NOTES
Apply aerodynamic seal.
If required, apply one layer of fluid resistant polyurethane topcoat matching customer paint scheme code X010.
Rig seal plates and adjust shims/combine as required for inboard stiffeners.
KGC991−1673−1/−3 (LH)
KGC991−1673−2/−4 (RH)
(INBD STIFFENER)
KGC991−1671−3 (LH)
KGC991−1671−4 (RH)
(MODIFIED P−SEAL)
KGC991−1675−1/−5 (LH)
KGC991−1675−2/−6 (RH)
(BRACKET ASSY)
KGC991−1671−5 (LH)
KGC991−1671−6 (RH)
(SEAL/SEAL PLATE SUB−ASSY)
KGC991−1674−1 (LH)
A−NUT PLATE ASSY
(3 PLACES)
KGC991−1672−1 (LH)
KGC991−1672−2 (RH)
(OUTBD STIFFENER)
KGC991−1673−1/−3 (LH)
KGC991−1673−2/−4 (RH)
(INBD STIFFENER)
MS20426AD4−5S
(RIVET)
MS20426AD5−5S
(RIVET)
0.30 in
(7.62 mm)
(RADIUS)
0.32 in
(8.13 mm)
0.80 in
(20.32 mm)
0.30 in
(7.62 mm)
1.558 in
(39.57 mm)
1.953 in
(49.61 mm)
17.95 in
(455.93 mm)
KGC991−1672−1 (LH)
KGC991−1672−2 (RH)
(OUTBD STIFFENER)
Apply fay surface seal to attaching bracket assembly when installling onto the trailing edge.
KGC991−1671−3 (LH)
KGC991−1671−4 (RH)
(MODIFIED P−SEAL)
SB700−27−6509_003
Apply CIC on and around the bottom leg of attaching bracket assembly.
Cutouts to align with bosses on attaching bracket assembly.
6
7
8
9
10
11
6
7
7
8 8
11
10
9
9
INBD FLAP
LOWER OML
0.20 in
(5.08 mm)
MAXIMUM
0.40 in
(10.16 mm)
REF
PRE−REWORK EDGES
Rework KGC991−1673−1/−2 aft flange tool access holes as shown and identify as KGC991−1671−7/−8.12
12
MODEL BD−700−1A10 (BD−700)
Installation of Improved Inboard Flap Seal Plate
Figure 10 (Sheet 3 of 3)
Basic Issue: Oct 04/2022
Revision 01: May 05/2023
700−27−6509
Page 31 of 31

### Page 34

700−27−6509 Rev. 01 May 05/2023
SPECIAL CHECK/MODIFICATION – FLAP SYSTEM –
INSTALLATION OF IMPROVED INBOARD FLAP SEAL PLATE
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 35

SERVICE BULLETIN INCORPORATION SHEET − "700−27−6509"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−27−6509 01
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
