# Bombardier Service Bulletin 700-35-6003

Copy: Revision 02 ("SB 700-35-6003 Rev02"), 18 pages: PDF https://openairdocs.org/files/sha256/2a/a5/2aa5e929586e44dce9a5134a98c62ad4e4d2b539b4bd75ae43ce60f720f782e3; text https://openairdocs.org/service-documents/bombardier/sb-700-35-6003/file/2aa5e929586e.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0725; AD 2020-02-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-35-6003
- Latest revision known: 700-35-6003, Revision 02, dated November 23, 2018 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-35-6003

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-02-15](https://openairdocs.org/ad/2020-02-15.md), effective Mar 12, 2020: Revisions 01 and 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-35-6003/proposed.md).

## Text (18 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0725; AD 2020-02-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Revision 01 of this Service Bulletin dated Sep 05/2018 and replace in its
entirety with this Revision 02.
Service Bulletin No. 700−35−6003
Date of Basic Issue Jul 03/2018
Revision No. 01 Dated Sep 05/2018
Revision No. 02 Dated Nov 23/2018
This revision has no effect for aircraft on which the Basic Issue or Revision 01 of this
Service Bulletin was done thus no other action is necessary. Do not sign the log book
if you have not done this revision. Keep the previous log book entry. You may make
an entry as “Not Applicable” for this revision.
This revision is issued to:
1. Revise in Paragraph 1.A., to add aircraft 9817 to the effectivity.
2. Make miscellaneous minor changes, as necessary, with no change in context.
SERVICE BULLETIN
MODEL BD−700−1A10 (BD−700)
700−35−6003
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

MODIFICATION - PORTABLE OXYGEN PROVISION -
REPLACEMENT OF THE BRACKET OF THE OXYGEN BOTTLE BRACKET
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
At the next 60−months
inspection that follows this
Service Bulletin Release Date
(Basic Issue))
EFFECTIVITY: Refer to Paragraph 1.A.
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive, which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services
at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 35−30
OXYGEN
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 1 of 1
This Service Bulletin is available at:

### Page 3

MODIFICATION - PORTABLE OXYGEN PROVISION -
REPLACEMENT OF THE BRACKET OF THE OXYGEN BOTTLE BRACKET1.
PLANNING INFORMATION
NOTES: 1. Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. For any technical issues, contact CSE, Technical Support, Global Express
by e−mail at SRPSA@aero.bombardier.com.
A. Effectivity
BD−700−1A10 aircraft, Serial No. 9381, 9438, 9460, 9470, 9475, 9478, 9479,
9481, 9484, 9485, 9499, 9524, 9529, 9530, 9533, 9538, 9551, 9553, 9568, 9598,
9615, 9624, 9632, 9638, 9640, 9641, 9648, 9657, 9670, 9680, 9682, 9689, 9700,
9706, 9723, 9726, 9730, 9731, 9745, 9752, 9753, 9757, 9759, 9773, 9775, 9804,
9814, 9816 and 9817.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
B. Reason
1. Condition:
On some aircraft, fast and easy access to the portable oxygen bottle was
prevented due to the bracket latch of the portable oxygen bottle upper bracket
assembly catching the rigid tube or the gauge on the bottle during portable
oxygen bottle retrieval.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 35−30
OXYGEN
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2018 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 1 of 14
This Service Bulletin is available at:

### Page 4

2. Evidence:
The current installation might not meet the requirement of Canadian Aviation
Regulations (CAR) 704, and Airworthiness Manual 525.1411, which require
easy access to the portable oxygen bottle for commercial operations when a
flight attendant is needed.
3. Objective/Benefit:
This Service Bulletin introduces a modified top bracket and new middle bracket
which will improve the access to the portable oxygen bottle.
C. Description
NOTE: Existing installation, location and quantity within the aircraft cabin may
vary. This Service Bulletin is to be performed on each applicable
installation. Refer to the applicable aircraft specific IPC or SIPC for more
details.
This Service Bulletin gives instructions to:
− Get access to the portable oxygen bottle,
− Install the new adaptor,
− Install the new upper bracket assembly,
− Install the new middle bracket assembly, and
− Install the portable oxygen bottle.
D. Compliance
Recommended at the next 60−months inspection that follows this Service Bulletin
Release Date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of TC STC number SA12–16, FAA STC number ST03088NY, EASA STC
number 10042314.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 2 of 14

### Page 5

F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to SB
700−00−6002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
3. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
2 man−hours is necessary to do this modification for each portable oxygen cylinder.
The labor required to do this Service Bulletin is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled at the next 60−months inspection that follows
its release date (Basic Issue).
G. Material − Cost and Availability
Kit 700K35−014 is necessary to do this modification.
KIT NO. PRICE
700K35−014 Please contact Bombardier Aerospace
Parts Services, in Montreal, for delivery
lead times and confirmation of prices.
NOTE: A kit is necessary for each portable oxygen cylinder installation.
This kit is available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace before the next
60−months inspection that follows this Service Bulletin release date
(Basic Issue).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 3 of 14

### Page 6

For all parts transactions, Bombardier Aerospace’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
During or after the above free period, Smart Parts Plus does not pay for the kit.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Torque Wrench
NOTES: 1. Refer to the Global 6000 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
2. Refer to the Liability Statement in the ITEM for the G6000 for
acceptable GSE equivalents.
I. Weight and Balance
It is the responsibility of the maintenance facility incorporating this change to
calculate the weight and balance impact for this installation and to update the
aircraft weight and balance report accordingly.
ITEM WEIGHT
Middle Bracket Assembly (Part No.
H3−2178−1)
0.21 pounds (0.10 kg)
Adaptor Plate (Part No.
BAS67039859−22)
0.34 pounds (0.15 kg)
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Drawing BAS67039859, Rev. A.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
− Global 6000 BD−700 Aircraft Maintenance Manual (AMM), Chapter 6.
− Global 6000 BD−700 Structural Repair Manual (SRM), Chapter 51.
− Bombardier Aerospace, Instructions for Continued Airworthiness, BAS67058060
(attached).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 4 of 14

### Page 7

L. Other Publications Affected
− Bombardier Aerospace, Supplemental Maintenance Manual (SMM), Chapter 35.
− Bombardier Aerospace, Supplemental Illustrated Parts Catalog (SIPC),
Chapter 35.
M. Equivalent Service Bulletins
For the Global Express and Global Express XRS BD−700−1A10 aircraft, use SB
700−35–014.
For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−35−013.
For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use SB 700−35−5003.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6000
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6000 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
3. Existing installation, location and quantity within the aircraft cabin may
vary. This Service Bulletin to be performed on each applicable installation.
Refer to the applicable aircraft specific IPC or SIPC for more details.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
Get access to the portable oxygen cylinder, usually in the forward wardrobe.
B. Modification
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Remove the oxygen cylinder from the upper bracket, Part No. 36758−02 or
36758−12, and lower brackets, Part No. 36758−01 or 36758−11. Refer to
Drawing BAS67039859.
(2) Remove and keep the screws and the upper and lower bracket. Refer to
Drawing BAS67039859.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 5 of 14

### Page 8

(3) Modify the upper bracket (1) as follows. Refer to Figure 1.
(a) Remove and discard the spring pins (2), spring (3), lever (4), and the
clamp (5), from the upper bracket (1).
(b) Re−identify the upper bracket (1) to BAS67039859−10 with an ink stamp,
per best shop practice.
(4) Install the adaptor plate, Part No. BAS67039859−22 as follows. Refer to
Drawing BAS67039859.
(a) Install the middle bracket, Part No. H3−2178−1 on the adaptor plate with
the screws, Part No. NAS1581F3T7 and the nuts, Part No. MS21042L3.
Torque the nuts 15 to 18 lbf in (1.70 to 2.03 Nm). Refer to Views A−A
(Post−Modification) and B−B.
(b) Position the adaptor over the inserts (on which the lower and upper
brackets were installed) View A−A (Post−Modification).
(c) Locate upper bracket on the adaptor plate, centering the upper bracket
and drill three holes to match the mounting inserts or nutplates in the
adaptor plate of a diameter of 0.165 to 0.169 in. (4.20 to 4.29 mm), as
shown in View A−A (Post−Modification).
NOTE: If the inserts are #10, drill the holes to 0.189 to 0.192 in. (4.80 to
4.87 mm).
(d) Mark the position of the two lower inserts to match the mounting inserts or
nutplates in the adaptor plate.
NOTE: If necessary, trim the adaptor to make sure that there is no
interference with existing parts.
(e) Drill the two marked holes in the adaptor plate of a diameter of 0.165 to
0.169 in. (4.20 to 4.29 mm).
NOTE: If the inserts are #10, drill the holes to 0.189 to 0.192 in. (4.80 to
4.87 mm).
(f) Remove the burrs and sharp edges.
(g) Touch−up the holes and, if necessary, the reworked areas of the adaptor
plate to finish A032. Refer to SRM 51−01−04.
NOTE: It is permitted to refinish the adaptor plate to a color to match the
surrounding color.
(h) Install the adaptor plate with the lower and upper brackets one of the ways
that follows:
(i) If there is mounting brackets, install the adaptor plate, the lower
bracket and the upper bracket with the existing screws on the
mounting brackets. If there is interference with other parts, it is
allowed to use the screws, Part No. MS35207−266, and the spacers,
Part No. NAS43DD3−24FC between the mounting brackets and the
adaptor plate. Torque the screws 12 to 15 lbf in (1.36 to 1.69 Nm).
Refer to Views A−A (Post−Modification) and C−C.
NOTE: It is allowed to use longer or shorter screws and spacers.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 6 of 14

### Page 9

(ii) If there is no mounting bracket, install the adaptor plate, the lower
bracket and the upper bracket with the screws, Part No.
MS35207−266, directly to the panel. If there is interference with other
parts, it is allowed to use the spacers, Part No. NAS43DD3−24FC
between the panel and the adapter plate. Torque the screws 12 to
15 lbf in (1.36 to 1.69 Nm). Refer to View C−C. Refer to Views A−A
(Post−Modification) and C−C.
NOTE: It is allowed to use longer or shorter screws and spacers.
(5) Install the oxygen cylinder on the lower brackets and middle bracket.
C. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
Remove all tools, equipment and unwanted materials from the aircraft.
D. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
Kit 700K35−014 is necessary to do this Service Bulletin and contains the parts that
follow:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
BAS67039859−22 1 Adaptor
Plate
− −
H3−2178−1 1 Middle
bracket
Assembly
− −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 7 of 14

### Page 10

NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
MS21042L3 3 Nut − −
MS35207−266 6 Screw − −
NAS1581F3T7 3 Screw,
countersink,
Reduced
Head
− −
NAS43DD3−24FC 6 Spacer − −
NOTES: 1. A kit is required for each portable oxygen installation.
2. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
3. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
No parts required.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
They can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Polyurethane
Topcoat
CT: 6 hours
−
BAMS 565−002
Color: Grey
#16515 per
FED−STD−595)
Color: To match
Aircraft Paint
Scheme
As Necessary Code: A
Primer, Epoxy
CT: 3.5 hours − BAMS 565−001 As Necessary Code: A
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 8 of 14

### Page 11

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Coating
Chemical
Conversion
Alodine
1200S
MIL−DTL−81706,
Class 1A As Necessary Code: B
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Tempo Aerospace
205 Fenmar Dr.
North York, ON, Canada
M9L 2X4
Tel.: (416) 746−2233
Fax.: (416) 746−2235
www.tempo−aerospace.com
Code: B
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 9 of 14

### Page 12

BAS67039859 − Portable Oxygen Bottle Bracket Replacement
(Sheet 1 of 4, Rev. A)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 10 of 14

### Page 13

BAS67039859 − Portable Oxygen Bottle Bracket Replacement
(Sheet 2 of 4, Rev. A)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 11 of 14

### Page 14

BAS67039859 − Portable Oxygen Bottle Bracket Replacement
(Sheet 3 of 4, Rev. A)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 12 of 14

### Page 15

BAS67039859 − Portable Oxygen Bottle Bracket Replacement
(Sheet 4 of 4, Rev. A)
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 13 of 14

### Page 16

GSB35014_001
1
2
3
4
5
MODEL BD−700−1A10 (BD−700)
Upper Bracket Modification
Figure 1
Basic Issue: Jul 03/2018
Revision 02: Nov 23/2018
700−35−6003
Page 14 of 14

### Page 17

700−35−6003 Rev. 02 Nov 23/2018
MODIFICATION − PORTABLE OXYGEN PROVISION −
REPLACEMENT OF THE BRACKET OF THE OXYGEN BOTTLE
BRACKET
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 18

SERVICE BULLETIN INCORPORATION SHEET − "700−35−6003"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−35−6003 02
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
