# Bombardier Service Bulletin 700-35-6501

Copy: Revision 01 ("700-35-6501 Rev01"), 26 pages: PDF https://openairdocs.org/files/sha256/f2/f9/f2f9382cdefec7c2c2fec5b1ec5b483c65404849d93d7d5e6d571bf9453fc867; text https://openairdocs.org/service-documents/bombardier/sb-700-35-6501/file/f2f9382cdefe.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0085; AD 2022-12-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-35-6501
- Latest revision known: 700-35-6501, Revision 01, dated February 12, 2021 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-35-6501

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2022-12-01](https://openairdocs.org/ad/2022-12-01.md), effective Jul 19, 2022: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-35-6501/proposed.md).

## Text (26 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0085; AD 2022-12-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Basic Issue of this Service Bulletin dated Sep 28/2020 and replace in its
entirety with this Revision 01.
Service Bulletin No. 700−35−6501
Date of Basic Issue Sep 28/2020
Revision No. 01 Dated Feb 12/2021
This revision has no effect for aircraft on which the Basic Issue of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as "Not Applicable" for this revision.
This revision is issued to:
1. Revise, in Paragraph 1.C. and 1.K., to add hoses details for the step on Appendix 1.
2. Deleted, in Paragraph 1.F., a NOTE for the labour hour calculation.
3. Added, in Paragraph 1.F., a new NOTE.
4. Revised, in Paragraph 1.F., restructured labour hour policy for PART A, PART B and
PART C.
5. Deleted, in Paragraph 1.G., parts purchase order statement.
6. Add, in Paragraph 1.K., Advisory Wire number.
7. Revise, in Paragraph 2.B.(1)., to add green fitting hoses to the statement.
8. Add, in Appendix 1 − Record Table, a new NOTES.
9. Make miscellaneous minor changes, as necessary, with no change of context.
SERVICE BULLETIN
MODEL BD−700−1A10 (BD−700)
700−35−6501
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

MODIFICATION – OXYGEN SUPPLY SYSTEM –
FLEXIBLE OXYGEN HOSE REPLACEMENT
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 9861 and 9872
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 35−11
OXYGEN
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 1 of 1
This Service Bulletin is available at:

### Page 3

MODIFICATION – OXYGEN SUPPLY SYSTEM –
FLEXIBLE OXYGEN HOSE REPLACEMENT
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. Due to different aircraft configurations, operators must first inspect their
existing oxygen hose installation prior to placing an order with Parts
Services.
3. Bombardier Aviation recommends to replace all existing O2C20T1 hoses
at the earliest opportunity.
Operators that cannot do the replacement at inspection time must repeat
the pressure and leak tests in PART B until all the O2C20T1 hoses are
replaced, as described in TCCA Airworthiness Directive.
4. Aircraft less than five years must repeat PART B every 30 months until all
O2C20T1 hoses are removed and replaced.
5. Aircraft five years and over must repeat PART B every 15 months until all
O2C20T1 hoses are removed and replaced.
6. All O2C20T1 series hoses must be replaced within 10 years of Aircraft
Completion STC issuance.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 35−11
OXYGEN
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2020−2021 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 1 of 22
This Service Bulletin is available at:

### Page 4

A. Effectivity
BD−700−1A10 aircraft, Serial No. 9861 and 9872.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
After the deployment functional test of the oxygen masks at a scheduled
maintenance, Bombardier Service Center reported that four hoses used for the
passenger oxygen were found damaged.
2. Evidence:
After investigation, it was found that over time, the O2C20T1 series hoses may
have leak points in them through structural cracks or breaks, and may become
rigid or brittle at some areas.
3. Objective/Benefit:
The intent of this Service Bulletin is to remove and replace all installed
O2C20T1 series flexible oxygen hoses, with 3891X series hoses.
Engineering evaluation has concluded that 3891X series flexible oxygen hoses,
which are manufactured from different materials, have shown no sign of
deterioration due to age or other environmental factors.
C. Description
This Service Bulletin gives instructions in PART A to:
− Inspect the hose assembly installations located in the crew rest PSU, the cabin
PSUs, the RHS dado (therapeutic oxygen) and the AFT flexible transitions,
− Fill out Appendix 1 with the affected O2C20T1 series flexible oxygen hoses part
numbers found installed, and
− Order the replacement parts as required and per aircraft configuration.
This Service Bulletin gives instructions in PART B to:
− Do the periodical testing, until full replacement of all O2C20T1 series hoses.
This Service Bulletin gives instructions in PART C to:
− Remove the O2C20T1 series hoses, and
− Install the 3891X series hoses as per Figure 2.
After PART C, this Service Bulletin gives instructions to:
− Do the necessary tests of the oxygen system.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 2 of 22

### Page 5

D. Compliance
Recommended within five months from this Service Bulletin release date (Basic
Issue) for PART A and PART B.
Recommended within 10 years from Aircraft Completion STC issuance for PART C.
NOTES: 1. Bombardier Aviation recommends that this Service Bulletin be done at
the operator’s earliest convenience, unless otherwise directed by the
airworthiness authority of the operator.
2. If it is not possible to complete all the instructions in this Service
Bulletin because of the aircraft configuration, submit an SRPSA for
analysis and to get an approved disposition to complete this Service
Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of TC STC number SA12−16, FAA STC number ST03088NY, EASA STC
number 10042314.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, repainting, supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−6502.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
2 man−hours are necessary to do PART A of this modification.
NOTE:
− 2 hours are required to get access for a visual of the hose fittings.
There is no need to remove completely the furniture to get access.
− It is recommended to do the replacement Part C during the same
downtime as the inspection in order to save removal/installation time.
3 man−hours are necessary to do PART B of this modification.
8 man−hours are necessary to do PART C of this modification.
The labor required to do PART A of this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 3 of 22

### Page 6

− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 24 months from Aircraft
Completion STC issuance.
Bombardier Aviation does not pay for the labor to do PART B of this Service
Bulletin.
The labor required to do PART C of this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 24 months from Aircraft
Completion STC issuance.
G. Material − Cost and Availability
No kit is necessary to do this modification. For material data, refer to Paragraph
3.C.
The parts in Paragraph 3.B. are necessary to do this modification.
The parts are available at no cost if:
− the parts are ordered in less than four (4) years of Aircraft Completion STC
issuance, and
− a no−charge purchase order is sent to Bombardier Aviation in less than 30
months, from this Service Bulletin release date (Basic Issue).
During or after the above free period, Smart Parts does not pay for the parts.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
12X−20−02 − Nitrogen Service Cart
20X−10−01 S4933959−501 Tag, Circuit Breaker
35X−10−01 G700−351001−29 Test Kit − Crew OxygenSystem
Commercially Available − Electrical Outlet Tester
Commercially Available −
Oxygen Pressure Test Gauge
(OPTG) with a Resolution of
2 psi (13.79 kPa) Minimum
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 4 of 22

### Page 7

GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Tag, DO NOT ACTIVATE
Commercially Available − Wrench, Torque 100 to 125 lbfin (11.30 to 14.12 Nm)
NOTES: 1. Refer to the Global 6500 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
2. Refer to the Liability Statement in the ITEM for the G6500 for
acceptable GSE equivalents.
3. Refer to the Pressure task applicable to your aircraft in IFCA
BAS67058081 (attached) for the requirement of the Nitrogen service
cart or not.
4. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive, (pending).
− Advisory Wire, AW700−35−0794.
− Bombardier Instructions for Continued Airworthiness (IFCA), BAS67058081
(attached).
− Bombardier Aviation, Kit Drawing BAS67638098, Rev. A.
− Global 6500 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 12, 24,
25, 35 and 52.
− Global 6500 BD−700 Illustrated Tool and Equipment Manual (ITEM),
Chapters 20 and 35.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapters 20 and 51.
− Supplemental Maintenance Manual (SMM), Chapters 24, 25 and 35.
− Appendix 1 − Record Table (attached) for O2C20T1 series flexible oxygen
hoses only (green fitting hoses).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 5 of 22

### Page 8

L. Other Publications Affected
None.
M. Equivalent Service Bulletins
− For the Global Express and Global Express XRS BD−700−1A10 aircraft, use
SB 700−35−015.
− For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−35−014.
− For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use SB 700−35−5005.
− For the Global 6000 BD−700−1A10 aircraft, use SB 700−35−6005.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6500
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6500 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) For PART A :
(a) No setup required.
(3) For PART B :
(a) No setup required.
(4) For PART C :
(a) Obey all the oxygen system safety precautions. Refer to
AMM 35−00−00−910−801.
(b) Make sure the BATTERY MASTER switch in the flight compartment is set
to OFF.
(c) Open the applicable PSUs. Refer to SMM 25−17−64−010−801,
SMM 25−28−54−010−801 and SMM 25−42−56−010−801.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 6 of 22

### Page 9

B. PART A — Part Number Inspection on Existing Oxygen System
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Refer to Figure 1 and Figure 2 and inspect the part number of the oxygen hose
installations at the locations that follow. For recording purposes, note the green
hoses installed part numbers only in Table 2 of Appendix 1 (attached):
(a) If installed, remove the mid cabin removable partition. Refer to
SMM 25−23−64−000−801.
(b) Open and inspect the installation in the crew rest PSU. Refer to
SMM 25−17−64−010−801.
(c) Open and inspect the installations in the cabin PSUs. Refer to
SMM 25−28−54−010−801.
(d) Inspect the cabin transition hose installations.
(e) Inspect the installation in the AFT lavatory as follows:
(i) If the installation is in the PSU, open the AFT lavatory PSU. Refer to
SMM 25−42−56−010−801.
(ii) If the installation is behind the headliner, remove the AFT lavatory
headliner. Refer to SMM 25−42−54−000−801.
(iii) Inspect the installation in the AFT lavatory.
(f) Remove the two RHS dado panels, or until visual inspection is possible.
Refer to SMM 25−28−56−000−801.
(g) Inspect the two therapeutic oxygen installations.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 7 of 22

### Page 10

A GREEN FITTING CORRESPONDS TO
THE O2C20T1 SERIES
REMOVE AND REPLACE
A BLUE FITTING CORRESPONDS TO
THE 3891X SERIES
NO REPLACEMENT REQUIRED
SB700−35−6501_001
FIGURE 1
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 8 of 22

### Page 11

(2) If no O2C20T1 series hose is installed, then PART B and PART C of this
Service Bulletin is not applicable to your aircraft. Make an entry in the aircraft
log and go to Paragraph 2.F. Close−out.
(3) If one or more O2C20T1 series hose is installed, do one of the following
options:
(a) Option 1 − Replacement (mandatory for aircraft 10 years and up)
(i) Place an order for the replacement parts. Refer to Paragraph 3.B.
NOTE: It is permissible to install a longer or shorter hose assembly
to ensure a proper installation.
(ii) Go to Paragraph 2.A.(4) Aircraft Setup for PART C .
(iii) Continue to Paragraph 2.D.
(b) Option 2 − Test and replace at a later date.
(i) Go to Paragraph 2.C., PART B — Scheduled Testing
C. PART B — Scheduled Testing
NOTES: 1. If it is not possible to complete all the instructions in this Service
Bulletin because of the configuration of the aircraft, submit an SRPSA
for analysis and to get an approved disposition to complete this
Service Bulletin.
(1) For aircraft less than five years from Aircraft Completion STC, repeat the
following tests every 30 months:
(a) Do the pressure test of the passenger oxygen system. Refer to
SMM 35−21−50−780−801 or SMM 35−21−01−780−802 for the applicable
effectivity in the IFCA BAS67058081 (attached).
(b) Do the leak test of the therapeutic oxygen system. Refer to
SMM 35−22−50−790−801.
(c) If any of the O2C20T1 series hose fails the above tests, then all O2C20T1
series hoses must be replaced at this time, do the following:
(i) Place an order for the replacement parts. Refer to Paragraph 3.B.
NOTE: It is permissible to install a longer or shorter hose assembly
to ensure a proper installation.
(ii) Go to Paragraph 2.A.(4) Aircraft Setup for PART C .
(iii) Continue to Paragraph 2.D., PART C — Modification — Flexible
Oxygen Hose Replacement.
(2) For aircraft over five years from Aircraft Completion STC, repeat the following
tests every 15 months:
(a) Do the pressure test of the passenger oxygen system. Refer to
SMM 35−21−50−780−801 or SMM 35−21−01−780−802 for the applicable
effectivity in the IFCA BAS67058081 (attached).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 9 of 22

### Page 12

(b) Do the leak test of the therapeutic oxygen system. Refer to
SMM 35−22−50−790−801.
(c) If any of the O2C20T1 series hose fails the above tests, then all O2C20T1
series hoses must be replaced at this time, do the following:
(i) Place an order for the replacement parts. Refer to Paragraph 3.B.
NOTE: It is permissible to install a longer or shorter hose assembly
to ensure a proper installation.
(ii) Go to Paragraph 2.A.(4) Aircraft Setup for PART C .
(iii) Continue to Paragraph 2.D., PART C — Modification — Flexible
Oxygen Hose Replacement.
(3) Repeat step (1) or step (2) at required intervals until O2C20T1 series hoses
are removed and replaced and PART Cof this Service Bulletin is incorporated.
NOTE: PART C of this Service Bulletin must be completed within 10 years of
Aircraft Completion STC issuance.
D. PART C — Modification — Flexible Oxygen Hose Replacement
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Obey all the oxygen−system safety precautions. Refer to
AMM 35−00−00−910−801.
(2) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
WARNING: BE CAREFUL WHEN YOU DO WORK ON OR NEAR THE
CAPILLARY LINES.  CAPILLARY LINES CAN BE EASILY
DAMAGED.  IF THEY ARE DAMAGED, IT CAN CAUSE INJURY TO
PERSONNEL AND DAMAGE TO EQUIPMENT.
WARNING: WHEN YOU LOOSEN OR TIGHTEN THE CAPILLARY LINES, MAKE
SURE THAT THE CAPILLARY LINES DO NOT TURN WITH THE
FITTINGS. IF YOU DO NOT DO THIS, YOU CAN CAUSE THE LINE
TO BREAK AND CAUSE INJURY TO PERSONNEL.
WARNING: DO NOT LET OIL, GREASE, OR SOLVENTS GET ON YOUR
HANDS, CLOTHING, OR THE EQUIPMENT USED TO DO WORK
ON THE OXYGEN SYSTEM. IF OXYGEN TOUCHES OIL, GREASE
OR SOLVENTS, THEY CAN START TO BURN.
(3) Remove and replace all O2C20T1 series hose installed at the locations shown
in Figure 2 as follows. Refer to the applicable Notes on Figure 2:
NOTES: 1. Keep all lines, fittings and connections completely free of oil,
grease and foreign matter. Cap open ends of cleaned and dried
tubing connections at all times.
2. Do not put thread compound on the female fitting.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 10 of 22

### Page 13

3. Do not put thread compound on the first two male threads.
4. Do not use Teflon tape on any flared male or female tube fittings
and coupling sleeve threads.
5. For the connection of oxygen lines on male pipe threads, apply
Teflon tape conforming to MIL−T−27730. On male flared threads
apply only anti−seize compound which conforms to
MIL−PRF−27617, Type II, which is suitable for gaseous oxygen.
6. Make sure that you do not make a scratch on the sealing
surfaces during installation.
7. Oxygen lines must be mounted above wires, fuel and hydraulic
system lines.
8. Oxygen lines spaced 6 in (152 mm) away from wires need no
special protection.
9. Oxygen lines spaced 6 to 2 in (152 to 50 mm) from wires shall
require to be sheathed in conduit or be securely clamped and
have cable ties installed at intervals less than the distance
between the wiring and oxygen lines.
10.Oxygen lines spaced 2 to 0.5 in (50 to 12 mm) from wires shall
require wires to be encased in insulated conduit and securely
clamped. These clamps shall not be used for support of wires.
11.Oxygen lines separated from wiring by conductive barrier may be
spaced 0.5 in (12 mm) from the wires.
12.Oxygen lines must be spaced 6 in (152 mm) from fuel, oil,
hydraulics, engine, flight linkage and any moving parts.
13.Where oxygen line crosses electrical, hydraulic or fuel lines,
protect for 6 in (152 mm) each side of crossing by covering with
convolex.
CAUTION: USE TWO WRENCHES WHEN YOU REMOVE/TORQUE THE
HOSES/TUBES.  USE ONE WRENCH TO HOLD THE FITTING,
AND THE OTHER WRENCH TO LOOSEN/TORQUE THE
COUPLING NUT.  IF YOU DO NOT DO THIS, YOU CAN
CAUSE DAMAGE TO THE COMPONENTS.
CAUTION: MAKE SURE THAT YOU PUT A PROTECTIVE COVER OR
CAP IN ALL THE OPEN OXYGEN LINES AND COMPONENT
FITTINGS. IF YOU DO NOT DO THIS IMMEDIATELY AFTER
THEY ARE DISCONNECTED, UNWANTED MATERIALS CAN
GO INTO THE OXYGEN SYSTEM. THIS CAN CAUSE
CONTAMINATION OF THE OXYGEN SYSTEM.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 11 of 22

### Page 14

(a) Disconnect and discard the O2C20T1 series hoses.
CAUTION: NO TEFLON TAPE IS TO BE USED ON MALE FLARED
THREADS, COUPLING SLEEVES, OR ON THE OUTSIDE OF
TUBE FLARES.
(b) Assemble the 3891X series hoses. Refer to
SPM−MM 20−22−00−910−801.
CAUTION: DO NOT TIGHTEN THE FITTING TO MORE THAN THE
MAXIMUM RANGE FOR THE SPECIFIED TORQUE. TOO
MUCH TORQUE CAN CAUSE POSSIBLE LEAKAGE OR
DAMAGE TO THE PLUMBING LINE.
(c) Torque the fittings from 100 to 125 lbf in (11.30 to 14.12 Nm). Refer to
SPM−MM 20−22−00−910−802.
(4) If applicable, set the ON/OFF switch on the oxygen cylinder regulator to ON.
Refer to AMM 35−00−00−910−801.
E. Testing
(1) Connect the electrical power to the aircraft. Refer to AMM 24−00−00−861−802.
(2) Open the oxygen fill and indicator door (121CL).
WARNING: DURING THIS TEST, OXYGEN MAY BE RELEASED; THEREFORE
ALL POSSIBLE IGNITION SOURCES SHOULD BE REMOVED
FROM THE AIRCRAFT
(3) Do the pressure test of the passenger oxygen system. Refer to
SMM 35−21−50−780−801 or SMM 35−21−01−780−802  for the applicable
effectivity in the IFCA BAS67058081 (attached).
(4) Do the leak test of the therapeutic oxygen system. Refer to
SMM 35−22−50−790−801.
(5) Remove the electrical power from the aircraft. Refer to AMM
24−00−00−861−802.
F. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) If opened, close the AFT lavatory PSU. Refer to SMM 25−42−56−410−801.
(3) If removed, install the AFT lavatory headliner. Refer to
SMM 25−42−54−400−801.
(4) Close the cabin PSUs. Refer to SMM 25−28−54−410−801.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 12 of 22

### Page 15

(5) Close the crew area PSU. Refer to SMM 25−17−64−410−801.
(6) Install the RHS dado panels. Refer to SMM 25−28−56−400−801.
(7) If removed, install the mid cabin removable partition. Refer to
SMM 25−23−64−400−801.
(8) If removed, install the forward equipment compartment access panels
(131AL/132AR). Refer to AMM 52−45−05−400−801.
(9) If opened, close the oxygen fill and indicator door (121CL).
G. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin is completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
The parts that follow are necessary to do this Service Bulletin and are available
from Bombardier Aviation Parts Services, Montreal:
NEW PART
NO.
QTY ITEM USED PART NO. INSTRUCTIONS
- DISPOSITION
38911−05−0040
See Note 2
A/R Hose
Assembly,
Straight
O2C20T1−5−0400 Discard
38911−05−0070 A/R Hose
Assembly,
Straight
O2C20T1−5−0700 Discard
38911−05−0080 A/R Hose
Assembly,
Straight
O2C20T1−5−0800 Discard
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 13 of 22

### Page 16

NEW PART
NO.
QTY ITEM USED PART NO. INSTRUCTIONS
- DISPOSITION
38911−05−0100 A/R Hose
Assembly,
Straight
O2C20T1−5−1000 Discard
38911−05−0120 A/R Hose
Assembly,
Straight
O2C20T1−5−1200 Discard
38911−05−0150 A/R Hose
Assembly,
Straight
O2C20T1−5−1500 Discard
38911−05−0160 A/R Hose
Assembly,
Straight
O2C20T1−5−1600 Discard
38911−05−0250 A/R Hose
Assembly,
Straight
O2C20T1−5−2500 Discard
38911−05−0310 A/R Hose
Assembly,
Straight
O2C20T1−5−3100 Discard
38911−05−0360 A/R Hose
Assembly,
Straight
O2C20T1−5−3600 Discard
38911−05−0540
See Note 2
A/R Hose
Assembly,
Straight
O2C20T1−5−5400 Discard
38911−05−0720 A/R Hose
Assembly,
Straight
O2C20T1−5−7200 Discard
38913−05−0100 A/R Hose
Assembly,
One Side 90
Deg
O2C20T14−5−1000 Discard
38913−05−0250 A/R Hose
Assembly,
One Side 90
Deg
O2C20T14−5−2500 Discard
AD003−05AG A/R Elbow, 90
Deg
− −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 14 of 22

### Page 17

NEW PART
NO.
QTY ITEM USED PART NO. INSTRUCTIONS
- DISPOSITION
CB9120V5 A/R Mounting
Base
− −
MS21042L3 A/R Nut − −
MS21919WDG9 A/R Clamp − −
MS3367−5−9 A/R Tyrap − −
NAS1149F0332P A/R Washer − −
NAS1801−3−8 A/R Screw − −
O2C10T05−5−5 A/R Elbow Line
Type Assy
− −
O2C10T1−5−5 A/R Line Type
Assy
− −
NOTES: 1. The part numbers for the items listed above are subject to change
without revision to this Service Bulletin. In case of discrepancy
between this list and any other list, the Illustrated Parts Catalog
prevails and shall be used to determine the latest part number.
2. If required.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aviation does not pay
for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Tamper Proof
Sealant
CT: 24 hours
Scotch−seal
1252 − As NecessaryFor PART C Code: A
Tape,
Anti−Seize − A−A−58092 As NecessaryFor PART C Code: A
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 15 of 22

### Page 18

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Adhesive,
Sealant,
Silicone, RTV,
Noncorrosive
CT: 24 to 72
hours
RTV 3145 MIL−A−46146 As NecessaryFor PART C Code: B
Adhesive
CT: Up to 36
hours
Araldite 2011 − As NecessaryFor PART C Code: C
Lacquer,
Gloss, for
Aircraft
A−A−3165
Color White − As NecessaryFor PART C Code: D
Alcohol,
Isopropyl − TT−I−735 GradeB As NecessaryFor PART C Code: E
Brush, Paint,
Natural or
Synthetic
Bristle
− − As NecessaryFor PART C Code: E
Cloth, No−Lint − − As NecessaryFor PART C Code: E
Compound,
Leak
Detection
− MIL−PRF−25567 As NecessaryFor PART B Code: E
Grease,
Aircraft and
Instrument,
Fuel and
Oxidizer
Resistant
− MIL−PRF−27617Type II As NecessaryFor PART C Code: E
Lockwire,
CRES 0.020
in (0.51 mm)
MS20995C20 − As NecessaryFor PART C Code: E
Scraper,
Non−Metallic − − As NecessaryFor PART C Code: E
Tape,
Anti−Seize − MIL−T−27730 As NecessaryFor PART C Code: E
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 16 of 22

### Page 19

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Tape,
Anti−Seize − MIL−T−27730A As NecessaryFor PART C Code: E
Tape,
Masking − − As NecessaryFor PART C Code: E
Torque Seal,
Tamper−Proof
Indicator
Paste
Dykem Cross
Check − As NecessaryFor PART C Code: E
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
3M Adhesive Division
3M Center Building 21−1W−10
900 Bush Ave.
St Paul, MN, 55144−1000
U.S.A.
Tel: 1−800−362−3550
http://www.3M.com/industrial
Code: B
Dow Corning Corp.
2200 Salzburg Road W.
Midland, MI
U.S.A. 48686−0994
Tel.: (989) 496−4400
www.dow.com
Code: C
Huntsman Advance Materials
5121 San Fernando Road W.
Los Angeles, CA
U.S.A. 90039−1101
Tel.: (888) 564−9318
www.huntsman.com
Code: D
Tempo Paint and Varnish Co.
205 Fenmar Dr.
Weston, Ontario
Canada, M9L 2X4
Tel.: (416) 746−2233
www.tempo−aerospace.com
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 17 of 22

### Page 20

SUPPLIERS ADDRESSES BY CODES
Code: E
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 18 of 22

### Page 21

APPENDIX 1 — RECORD TABLE
FLEXIBLE OXYGEN HOSE PART NUMBER CHECK
NOTES: 1. Write the P/N of the green fittings O2C20T1 series flexible oxygen hoses
or N/A, if no installation or other than O2C20T1 series flexible oxygen
hoses.
2. This appendix is for Operator reference only and is not required to be sent
to Bombardier Aviation.
TABLE 1
AIRCRAFT SERIAL NO. AIRFRAME HOURS AIRCRAFT CYCLES
TABLE 2
Crew Rest
Existing P/N: ______________________ −
LHS Cabin PSUs and Transitions RHS Cabin PSUs and Transitions
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 19 of 22

### Page 22

TABLE 2
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
AFT Lavatory PSU or Headliner
Existing P/N: ______________________ Existing P/N: ______________________
Therapeutic Oxygen
Existing P/N: ______________________
FS:______________________________
Existing P/N: ______________________
FS:______________________________
MODEL BD−700−1A10 (BD−700)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 20 of 22

### Page 23

SB700−35−6501−S1−PL 
Figure 2 − Flexible Oxygen Hose Assy Modification
(Sheet 1 of 2, Rev. A)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 21 of 22

### Page 24

SB700−35−6501−S1 
Figure 2 − Flexible Oxygen Hose Assy Modification
(Sheet 2 of 2, Rev. A)
Basic Issue: Sep 28/2020
Revision 01: Feb 12/2021
700−35−6501
Page 22 of 22

### Page 25

700−35−6501 Rev. 01 Feb 12/2021
MODIFICATION – OXYGEN SUPPLY SYSTEM –
FLEXIBLE OXYGEN HOSE REPLACEMENT
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 26

SERVICE BULLETIN INCORPORATION SHEET − "700−35−6501"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−35−6501 01
COMPLIED WITH
YES    NO    N/A
PART A
PART B
PART C
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
