# Bombardier Service Bulletin 700-52-7511

Copy: No revision named ("700-52-7511"), 16 pages: PDF https://openairdocs.org/files/sha256/2c/7c/2c7c574426b975d707b052b61308a63206ca5097d3a28a85cbd5ac3fcfe233ce; text https://openairdocs.org/service-documents/bombardier/sb-700-52-7511/file/2c7c574426b9.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1646; AD 2023-04-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-52-7511
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-52-7511

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-04-01](https://openairdocs.org/ad/2023-04-01.md), effective Apr 7, 2023: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-52-7511/proposed.md).

## Text (16 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1646; AD 2023-04-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/REWORK – PASSENGER DOOR –
INSPECT AND MEASURE THE STEPS & GAPS AND DOOR STOPS RIGGING
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 72 months from this Service Bulletin
release date (Basic Issue)
EFFECTIVITY: A/C Serial No. 70006 to 70061
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
AIRWORTHINESS LIMITATIONS (AWL) NOYES
KITS and/or PARTS NOYES
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: NA
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−2A12 (BD−700)
ATA 52−11
DOORS
Basic Issue: Jul 22/2022 700−52−7511
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/REWORK – PASSENGER DOOR –
INSPECT AND MEASURE THE STEPS & GAPS AND DOOR STOPS RIGGING
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. All aircraft must send the recorded measurements to Bombardier
Customer Support Engineering.
A. Effectivity
BD−700−2A12 Aircraft Serial No. 70006 to 70061.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
Rigging of the door pressure stop fittings and the steps and gaps can be
affected by the aircraft’s loading condition whether on jacks or
Weight−on−Wheels (WoW). A number of aircraft may be affected by this rigging
as it was not performed in the final WoW configuration.
2. Objective/Benefit:
This Service Bulletin instructs to measure the passenger door steps and gaps,
and rigging of door stops. If the measurements are not within the limits,
re−adjustment to be done to obtain the necessary limits.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−2A12 (BD−700)
ATA 52−11
DOORS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2022 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jul 22/2022 700−52−7511
Page 1 of 13
This Service Bulletin is available at:

### Page 3

C. Description
This Service Bulletin gives instructions in PART A to:
− Measure and record the passenger door steps and gaps,
− Send the recorded measurements to Bombardier Customer Support
Engineering.
This Service Bulletin gives instructions in PART B to:
− If the measurements are not within limits, re−adjust (rigging) to get the
necessary limits, and
− Send the recorded measurements to Bombardier Customer Support
Engineering.
This Service Bulletin gives instructions in PART C to:
− Measure and record the passenger door stops rigging,
− Send the recorded measurements to Bombardier Customer Support
Engineering.
This Service Bulletin gives instructions in PART D to:
− If the measurements are not within limits, re−adjust (rigging) to get the
necessary limits, and
− Send the recorded measurements to Bombardier Customer Support
Engineering.
D. Compliance
Specified Time Compliance
Recommended within 72 months from this Service Bulletin release date (Basic
Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin. Standard
SRPSA fees may apply. Refer to the Services section of the Bombardier
customer portal for the latest prices, rates and fees.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 2 of 13

### Page 4

F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−7502.
2. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection. Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
02 man−hours are necessary to do PART A of this Service Bulletin.
28 man−hours are necessary to do PART B of this Service Bulletin.
02 man−hours are necessary to do PART C of this Service Bulletin.
12 man−hours are necessary to do PART D of this Service Bulletin.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
G. Material − Cost and Availability
No kit or parts are necessary to do this Service Bulletin. For material data, refer to
Paragraph 3.C.
H. Tooling
The equipment and tools listed below are necessary to do this Service Bulletin:
SGSE/GSE
REFERENCE NO. PART NO. DESCRIPTION
20−00−03 − Force gauge (2 to 100 lbs)
20−00−04 950−315 Digital Inclinometer
21X78K−21−01 − Fuselage−pressurizationadapter−panel kit
21X−00−05 − Safety net
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 3 of 13

### Page 5

SGSE/GSE
REFERENCE NO. PART NO. DESCRIPTION
21X78K−00−02 − Safety netpressurization−baggage−door
21X78K−00−01 − Cabin pressurization cart
52X78K−11−02 − Manual−release−system NLGquadrant/PAX−door rig pin
Commercially Available STD−0150 Digital stopwatch
Commercially Available STD−0084 Feeler Gauge
Commercially Available STD−0044 Ruler or Straightedge
Commercially Available STD−0020 Torque Wrench
NOTES: 1. Refer to the Global 7500 Illustrated Tool and Equipment Publication
(ITEP) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEP for the G7500 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the AMP, WM, Chapter 20,
then the tools called in the AMP, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive, (pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−70623,
Rev. −−.
− Bombardier Aviation, Functional Test Engineering Requirement,
FTER−CC700−521002, Rev. K.
− Global 7500 Aircraft Maintenance Publication (AMP), Chapters 6, 20, 24 and 52.
− Global 7500 Aircraft Structure Repair Publication (ASRP), Chapter 51.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 4 of 13

### Page 6

L. Other Publications Affected
None.
M. Equivalent Service Bulletins
None.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 7500
BD−700−2A12, Aircraft Maintenance Publication (AMP) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 7500 BD−700−2A12 Aircraft Maintenance Publication (AMP),
Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
BD700−A−J24−00−00−00AAA−012A−A.
(2) Obey all passenger−door safety precautions. Refer to
BD700−A−J52−11−00−00AAA−012A−A.
(3) Obey all landing−gear safety precautions. Refer to
BD700−A−J32−00−00−00AAA−012A−A.
B. PART A — Measurement of Passenger Door Steps and Gaps
(1) Measure and record the passenger door steps and gap values on each lateral
side of the door at 8 points, and on the lower and upper side of the door at 4
points. Refer to Figure 1 and the table below:
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 5 of 13

### Page 7

DOOR POINTS GAP VALUE STEP VALUE
P1 to P8
(Between door skin
forward−edge and
fuselage skin)
0.070 to 0.170 in
(1.78 to 4.31 mm)
−0.116 to −0.004 in
(−2.95 to −0.10 mm)
P13 to P20
(Between the door
lower−skin edge and
the fuselage lower−skin
edge)
P9 to P12
(Between the door
lower−skin edge and
the fuselage lower−skin
edge)
0.090 to 0.170 in
(2.29 to 4.31 mm
P21 to P24
(Between the door
upper−skin edge and
the fuselage upper−skin
edge)
0.140 to 0.220 in
(3.56 to 5.58 mm)
NOTES: 1. The values are for “Before Pressurization”, this is to comply with
final values mentioned in airframe aerodynamics smoothness per
ASRP BD700−A−J51−14−04−00AAA−361A−A, when aircraft is
“Pressurized”.
2. At least three of the four guide rollers must contact the guides on
the inboard surface during steps measure.
The gap on the fourth roller must be 0.000 to 0.020 in (0.00 to
0.50 mm).
3. Measure points to be at 1 in (25.4 mm), from the skin radius
corner.
4. Measure point to be at 1 in (25.4 mm), above fasteners row due
to the skin fuselage overlap.
(2) Send all the recorded values to Bombardier Customer Support Engineering
through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) If the above measurement is within the limits, go to PART C.
(4) If the above measurement is not within the limits, go to PART B.
C. PART B — Re−adjustment of Passenger Door Steps and Gaps
NOTE: If the aircraft has a paint stripe running through the passenger door, doing
a vertical rigging may result in mismatch of paint stripe.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 6 of 13

### Page 8

(1) If any of the measurement obtained from PART A is not within the limits,
re−adjust to obtain the necessary values. Do as follow:
1. Do the rigging of passenger door. Refer to Step 3, 4, 5, 6, 7, 8 and 9 from
BD700−A−J52−11−01−00AAA−275A−A.
2. Do the adjust procedure for passenger−door closed proximity−sensor.
Refer to BD700−A−J52−72−03−00AAA−271A−A.
3. Do the function test procedure for passenger door handles. Refer to
BD700−A−J52−11−05−02AAA−340A−A.
4. Do the operational test procedure for the passenger door. Refer to
BD700−A−J52−11−01−00AAA−320A−A.
5. Do the procedure to pressurize the cabin to a differential pressure of 4.00
psid (27,58 kPa). Refer to BD700−A−J21−31−00−00AAA−364A−A.
(2) Send all the recorded values to Bombardier Customer Support Engineering
through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) No further action required for PART C and D. Go to Close−out.
D. PART C — Measurement of Passenger Door Stops
NOTE: PART C and D should be disregarded if the passenger door is re−rigged
in PART B.
(1) With the door in closed position, measure and record the passenger door stops
gaps. Refer to Figure 2 and the table below:
LOCATION GAP VALUE
Between all the 10 lateral door stops
and the fuselage stop fittings.
Refer to Figure 2, Detail E.
0.001 to 0.005 in
(0.03 to 0.12 mm)
Between the 2 lower door stops and
the fuselage stop fittings.
Refer to Figure 2, Detail D.
0.001 to 0.005 in
(0.03 to 0.12 mm)
Between the 2 upper door stops and
the fuselage stop fittings.
Refer to Figure 2, Detail B.
0.001 to 0.025 in
(0.03 to 0.63 mm)
Between the lateral side of upper
door stops and the fuselage stops.
Refer to Figure 2, Detail C.
0.100 in Minimum
(2.54 mm)
(2) Send all the recorded values to Bombardier Customer Support Engineering
through SRPSA by e−mail at SRPSA@aero.bombardier.com.
(3) If the above measurement is within the limits, no further action is required.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 7 of 13

### Page 9

(4) If the above measurement is not within the limits, go to PART D.
E. PART D — Re−adjustment of Passenger Door Stops
(1) If any of the measurement obtained from PART C is not within the limits, do the
door stops rigging to obtain the necessary values. Refer to Step 5 of
BD700−A−J52−11−01−00AAA−275A−A.
(2) Do the adjust procedure for passenger−door closed proximity−sensor. Refer to
BD700−A−J52−72−03−00AAA−271A−A.
(3) Do the function test procedure for passenger door handles. Refer to
BD700−A−J52−11−05−02AAA−340A−A.
(4) Do the operational test procedure for the passenger door. Refer to
BD700−A−J52−11−01−00AAA−320A−A.
(5) Do the procedure to pressurize the cabin to a differential pressure of 4.00 psid
(27,58 kPa). Refer to BD700−A−J21−31−00−00AAA−364A−A.
(6) Send all the recorded values to Bombardier Customer Support Engineering
through SRPSA by e−mail at SRPSA@aero.bombardier.com.
F. Testing
No testing is required.
G. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
H. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin is completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
For information, corrections, comments and/or feedback regarding Service Bulletins
released on the Customer Portal, please contact the Service Bulletin Group at the
following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
No parts required.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 8 of 13

### Page 10

C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aviation does not pay
for these consumable.
DESCRIPTION
PART
NO./NAME
(SEE NOTE)
SPECIFICATION QUANTITY SUPPLIER
Protective tape,
polyurethane
flame retardant
(Patco 9425FR)
10−009 BAMS 553−007,Type VI As Necessary Code: A
Cotter pin
(MS24665−88) 05−030 MS24665 As Necessary Code: B
Cotter pin
(MS24665−304) 05−394 MS24665 As Necessary Code: B
Lockwire
(MS20995C32)
(Alternate for
safety cable)
05−005 NASM20995 As Necessary Code: B
Safety cable kit
(AS3510−0118K) 05−242 AS3510 As Necessary Code: B
Safety cable kit
(AS3510−0218K) 05−083 AS3510 As Necessary Code: B
Safety cable kit
(AS3510−0218C) 05−052 AS3510 As Necessary Code: B
Sealant 06−002
MIL−PRF−81733,
Type IV, Class
1, Grade A
As Necessary Code: B
Sealant 06−151 BAMS 552−002,Class B As Necessary Code: B
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 9 of 13

### Page 11

3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Berry Global Inc.
51 Ballou Blvd,
Bristol, RI − 02809
United States.
Code: B
Commercially Available
4. For details refer to consumable reference code listed in
AMP BD700−A−J51−31−00−00AAA−070A−A.
D. Publications
No publications required.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 22/2022 700−52−7511
Page 10 of 13

### Page 12

P9 P10 P11 P12
P1
P2
P3
P4
P5
P6
P7
P8
P21 P22 P23 P24
P20
P19
P18
P17
P16
P15
P14
P13
SB700−52−7511_001
A
FWD
A
MODEL BD−700−2A12 (BD−700)
Passenger Door Steps and Gaps
Figure 1
Basic Issue: Jul 22/2022 700−52−7511
Page 11 of 13

### Page 13

TYPICAL
C
A
A
FWD
BB
CC
DD
EE
TYPICAL
B
DOOR STOP FITTING
DOOR STOP FITTING
0.001 TO 0.025 in.
(0,03 TO 0,63 mm)
DOOR STOP
(REF)
SERRATION
(REF)
0.10 in.
(2,54 mm)
MINIMUM
0.10 in.
(2,54 mm)
MINIMUM
SB700−52−7511_011
MODEL BD−700−2A12 (BD−700)
Passenger Door Stops Rigging
Figure 2 (Sheet 1 of 2)
Basic Issue: Jul 22/2022 700−52−7511
Page 12 of 13

### Page 14

TYPICAL
D
TYPICAL
E
NUT
LOWER STOP PIN
NUTLATERAL STOP PIN
DOOR STOP FITTING
(REF)
0.001 TO 0.005 in.
(0,03 TO 0,13 mm)
0.001 TO 0.005 in.
(0,03 TO 0,13 mm)
DOOR STOP FITTING
(REF)
SB700−52−7511_012
MODEL BD−700−2A12 (BD−700)
Passenger Door Stops Rigging
Figure 2 (Sheet 2 of 2)
Basic Issue: Jul 22/2022 700−52−7511
Page 13 of 13

### Page 15

700−52−7511 Basic Jul 22/2022
SPECIAL CHECK/REWORK – PASSENGER DOOR –
INSPECT AND MEASURE THE STEPS & GAPS AND DOOR STOPS
RIGGING
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 16

SERVICE BULLETIN INCORPORATION SHEET − "700−52−7511"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−52−7511 Basic
COMPLIED WITH
YES    NO    N/A
PART A
PART B
PART C
PART D
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
