# Bombardier Service Bulletin 700-53-052

Copy: No revision named ("700-53-052 Basic"), 46 pages: PDF https://openairdocs.org/files/sha256/8d/35/8d352b844b9abd52f2e2c224845f10221173c2d11e5d7f4e7771719751e19ef7; text https://openairdocs.org/service-documents/bombardier/sb-700-53-052/file/8d352b844b9a.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0876; AD 2020-05-27 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-53-052
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-53-052

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-05-27](https://openairdocs.org/ad/2020-05-27.md), effective May 7, 2020: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-53-052/proposed.md).

## Text (46 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0876; AD 2020-05-27 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MODIFICATION - AFT FUSELAGE - REPLACEMENT AND
REINFORCEMENT OF THE RUDDER QUADRANT BOX ASSEMBLY HALF RIBS
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 9002 to 9312, 9314 to 9380 and 9384 to 9429
MANPOWER: Up to 46 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE NOYES
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services
at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 53−40
FUSELAGE
Basic Issue: Oct 01/2018 700−53−052
Page 1 of 1
This Service Bulletin is available at:

### Page 2

MODIFICATION - AFT FUSELAGE - REPLACEMENT AND
REINFORCEMENT OF THE RUDDER QUADRANT BOX ASSEMBLY HALF RIBS
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. Please contact your
Regional Manager (RM), Field Service Representative (FSR) or Customer
Service Representative (CSR) to schedule your aircraft as there is a
limited availability. The parts will be allocated on a first come first serve
basis.
For more information on dedicated schedules, refer to SB 700−00−002.
A. Effectivity
BD−700−1A10 aircraft, Serial No. 9002 to 9312, 9314 to 9380 and 9384 to 9429.
NOTES: 1. The instructions given in this Service Bulletin are only applicable to
the systems and parts installed at the time of delivery of the aircraft or
as changed by Bombardier Aerospace Service Bulletin(s).
Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 53−40
FUSELAGE
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2018 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Oct 01/2018 700−53−052
Page 1 of 31
This Service Bulletin is available at:

### Page 3

B. Reason
1. Condition:
Cracking was discovered on the AFT lower half−rib, Part No. GD417−1539−1,
and the FWD half rib, Part No. GD417−1588−3. These half−ribs are part of the
Rudder Quadrant Box Assembly.
2. Evidence:
Cracks initiating from rivet holes on the FWD half rib’s and the AFT lower half
rib’s attachment flange to the LH channel were discovered. In addition, cracks
were also discovered at the radius of the FWD half rib’s and the AFT lower half
rib’s attachment flange to the LH channel.
3. Objective/Benefit:
This Service Bulletin gives instructions to replace the half−ribs, Part No.
GD417−1539 and GD417−1588, the air systems support fitting, Part No.
GD437−1585 and to install two back−up fittings to strengthen the Rudder
Quadrant Box Assembly and prevent future cracks.
It also gives instructions to replace the LH channel, Part No. GD417−1520, if
necessary.
C. Description
This Service Bulletin gives instructions to:
− Open the Aft Equipment compartment door 311BB,
− Get access to the Rudder Quadrant box,
− Remove the discrepant Rudder Quadrant Box half ribs,
− Remove the air systems support fitting, Part No. GD437−1585,
− If cracked, remove the existing LH channel, Part No. GD417−1520,
− Install new Rudder Quadrant Box half ribs,
− Install the new air systems support fitting, Part No. GC437−0051−1,
− Install new Rudder Quadrant Box back−up fittings,
− If removed, install a new LH channel, Part No. GD417−1520−7S, and
− Do the necessary tests to make sure that the system operate(s) correctly.
D. Compliance
Specified Time Compliance, within 60 months from this Service Bulletin release
date (Basic Issue), or within 3000 accumulated Flight Cycles from C of A,
whichever comes first.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 2 of 31

### Page 4

Aircraft that have exceeded 2900 accumulated flight cycles from C of A at the time
of release of this Service Bulletin (Basic Issue), must incorporate this Service
Bulletin within 100 Flight Cycles or 12 months, whichever comes first from this
Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
This Service Bulletin is in reference to Advisory Wire AW700−53−0585.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to SB
700−00−002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
Up to 46 man−hours may be necessary to do this modification, and are broken
down as follows:
− 25 man−hours to replace and reinforce the Rudder Quadrant Box half ribs.
− 21 man−hours to replace the LH channel (if required)
Bombardier Aerospace does not pay for the labor to do this modification.
G. Material − Cost and Availability
Kit 700K53−6010 is necessary to do this modification.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 3 of 31

### Page 5

KIT NO. PRICE
700K53−6010 Please contact Bombardier Aerospace
Parts Services, in Montreal, for delivery
lead times and confirmation of prices.
In addition to the kit shown above, the part in Paragraph 3.B. may be necessary to
do this modification.
The kit and part are available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 60
months from this Service Bulletin release date (Basic Issue).
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are
used to reserve and manage inventory due to limited availability of rotable stock,
parts and/or kits. Parts are limited, therefore, advance part scheduling with our
In−Service Implementation Team (ISIT) is recommended prior to a maintenance
visit. Please contact your Regional Manager (RM), Field Service Representative
(FSR) or Customer Service Representative (CSR) to schedule your aircraft as there
is a limited availability. The parts will be allocated on a first come first serve basis.
During or after the above free period, Smart Parts Plus does not pay for the kit(s).
H. Tooling
The equipment and tools listed below are necessary to do this :
GSE REFERENCE NO. PART NO. DESCRIPTION
24−00−24 S4933959−501 Tag, Circuit Breaker
27X−00−03 G700−270003−1 Kit − Rudder/Elevator
Rigging Pins
27X−21−02 G700−272102−179 Fixture − Rudder Rigging
Commercially Available − Cable, Tensionmeter
Commercially Available − Wrench, Torque
NOTES: 1. Refer to the Global Express or Global Express XRS Illustrated Tool
and Equipment Manual (ITEM) to make sure that you use the correct
equipment configuration.
2. Refer to the Liability Statement for the GX/XRS for acceptable GSE
equivalents.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 4 of 31

### Page 6

I. Weight and Balance
WEIGHT MOMENT
+0.54 pound (0.245 kg) +562.80 pound−inches (6.48 kgm)
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Modification Summary, R700T400669, Rev. H.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01706,
Rev. A.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
− Bombardier Aerospace, Structural Repair Manual (SRM), Chapter 51.
− Bombardier Aerospace, Kit Drawing KGC991−1543, Rev. G.
− Advisory Wire AW700−53−0585.
− Appendix 1 − Eddy Current Inspection Requirements (attached).
− Appendix 2− Rudder Quadrant Box − LH Channel Replacement − Fastener Call
Out (attached).
− Appendix 3 − Detailed Visual Inspection Requirements (attached).
− Global Express or Global Express XRS BD−700 Aircraft Maintenance Manual
(AMM), Chapters 6, 24, 26, 27, 33 and 36.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−53−027.
For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use SB 700−53−5011.
For the Global 6000 BD−700−1A10 aircraft, use SB 700−53−6010.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 5 of 31

### Page 7

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global Express
or Global Express XRS BD−700−1A10, Aircraft Maintenance Manual
(AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
Global Express or Global Express XRS BD−700−1A10, Aircraft
Maintenance Manual (AMM), Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all flight control safety precautions. Refer to AMM 27−00−00−910−801.
(3) Obey all fuel−system safety precautions. Refer to AMM 28−00−00−910−801.
(4) Open the Aft Equipment−Compartment Door 311BB.
(5) Remove the LH bleed duct, Part No. GG468−4065. Refer to
AMM 36−11−61−000−801.
(6) Remove the strut assembly, Part No. GD417−1530 at the lug attachments and
keep the attaching hardware for later installation.
(7) Remove the ECS duct rod assembly, Part No. GD437−1590, and keep the
attaching hardware for later installation.
(8) Remove the APU fuel line, Part No. GD428−1019, and keep the attaching
hardware for later installation. Refer to SPM−MM 20−30−00−910−808 and
AIPC 28−21−65−43.
(9) Disconnect the inboard connector of the tail strobe−light power supply, Part
No. 8ES456038−03, to prevent damage, and put the protective covers on the
connector and receptacle. Refer to AMM 33−44−01−000−802.
(10) If necessary for access and to prevent damage, remove the APU Discharge
Line, Part No. GD774−1009. Refer to AMM 26−21−29−000−801.
(11) If necessary, remove fairleads (qty 3), Part No. GD478−1001, from hydraulic
lines to allow for movement and keep the attaching hardware for later
installation.
B. Modification
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 6 of 31

### Page 8

(1) Remove the existing FWD upper half rib, Part No. GD417−1588−3, the existing
AFT lower half rib, Part No. GD417−1539−1, and the existing air system
support fitting, Part No. GD437−1585−1 as follows:
(a) As required for access inside the rudder quadrant box, carefully remove
the existing rivets common to the top skin of the rudder quadrant box and
the parts that follow: the FWD upper half rib, the AFT upper half rib and
the LH and RH side channels. Refer to Figure 1.
(b) Carefully lift the top skin and temporarily attach it to have access inside
the rudder quadrant box.
(c) Carefully remove the fasteners common to the LH channel of the rudder
quadrant box and the parts that follow: the existing FWD upper half rib,
Part No. GD417−1588−3, and the existing AFT lower half−rib, Part No.
GD417−1539−1. Refer to Figure 1.
(d) Carefully remove the remaining fasteners common to the existing air
system support fitting, Part No. GD437−1585−1, and the LH channel.
(e) Carefully remove the fasteners, common to the FWD upper half rib, Part
No. GD417−1588−3 and the parts that follow: the FWD lower half rib, Part
No. GD417−1589, and the feel unit brace, Part No. GD417−1543. Refer to
Figure 1.
(f) Carefully remove the fasteners, common to the AFT lower half−rib, Part
No. GD417−1539−1, and the parts that follow: the bottom skin of the
rudder quadrant box and the feel unit fitting, Part No. GD417−1523. Refer
to Figure 1.
(g) Carefully remove the fasteners common to the AFT lower half−rib, Part
No. GD417−1539−1, and AFT upper half−rib, Part No. GD417−1539.
Refer to Figure 1.
(2) Before you install the new parts, do an inspection of the discrepant area as
follows:
(a) Do a surface Eddy Current and bolt hole Eddy Current inspection of the
LH channel, Part No. GD417−1520. Refer to Appendix 1, Eddy Current
Inspection Requirements.
(b) Perform a detailed visual inspection at 10X magnification of the remaining
FWD and AFT half ribs, Part No. GD417−1589 and Part No.
GD417−1539, the bottom skin, Part No. GD417−1526, the top skin, Part
No. GD417−1525 and the LH channel, Part No. GD417−1520, in the local
area around the air system support fitting installation. Refer to Appendix 3,
Detailed Visual Inspection Requirements for areas to be inspected.
NOTE: Make sure there are no pulled or damaged fasteners and that all
fasteners are seated in place properly.
(3) If pulled or damaged fasteners are found, submit an SRPSA with all the
necessary details for an approved disposition. If any damage is found other
then on the LH channel, submit an SRPSA with all the necessary details for an
approved disposition.
(4) If no cracks are found in the LH channel, Part No. GD417−1520, continue to
Paragraph 2.C.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 7 of 31

### Page 9

(5) If a crack is found in the LH channel, Part No. GD417−1520, the LH channel
must be replaced, continue to Paragraph 2.D.
C. Replacement and Reinforcement of the Half Ribs
(1) Put the new FWD upper half rib, Part No. GD417−1588−3 and new AFT lower
half rib, Part No. GD417−1539−1, in position as follows:
(a) Put the new FWD upper half rib, Part No. GD417−1588−3, in position.
(b) Use existing fastener holes in the LH channel, feel unit brace and existing
FWD lower half rib to drill the fastener holes in the new FWD upper half
rib, Part No. GD417−1588−3, and temporarily attach with clecos. Maintain
a minimum 2D edge distance, except where noted. Refer to Figure 2 and
Figure 3.
NOTE: Do not drill the two lower holes from the LH channel in the new
FWD upper half rib. Refer to Figure 3.
(c) Put the new AFT lower half rib, Part No. GD417−1539−1, in position.
(d) Use existing fastener holes in the LH channel, existing AFT upper half rib,
bottom skin and feel unit fitting, to drill the fastener holes in the new AFT
lower half rib, Part No. GD417−1539−1, and temporarily attach with
clecos. Maintain a minimum 2D edge distance, except where noted. Refer
to Figure 3, Figure 4 and Figure 5.
(e) Lower the top skin on the rudder quadrant box and use the existing
fastener holes in the top skin, to drill the holes for Hi−Lites in the new
FWD upper half rib, Part No. GD417−1588−3, make sure to maintain a
minimum 1.8D edge distance and 3.9D pitch. Refer to Figure 6 and
SRM 51−42−36.
(f) Carefully lift the top skin and temporarily attach it to have access inside
the rudder quadrant box.
(2) Put the FWD back up fitting, Part No. GC417−0151−1, the AFT back up fitting,
Part No. GC417−0152−3, and the new air system support fitting, Part No.
GC437−0051−1, in position as follows:
(a) Put the FWD back up fitting, Part No. GC417−0151−1, in position. Refer to
Figure 2
(b) Transfer drill all the pilot holes from the FWD back−up fitting through the
LH channel, the new FWD upper half rib and the bottom skin, transfer drill
the three existing fastener holes from the FWD half−rib through the FWD
back−up fitting and secure in place with clecos. Maintain minimum 2D
edge distance, except where noted. Refer to Figure 2, Figure 5, and
Figure 7.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 8 of 31

### Page 10

(c) Put the air system support fitting, Part No. GC437−0051−1, in position and
transfer drill the pilot holes from the FWD back−up fitting. Make sure you
have minimum 2D edge distance. Refer to Figure 2 and Figure 7.
NOTES: 1. Make sure that the bottom of the air system support fitting is
positioned 0.150 ±0.02 in (3.81 ± 0.50mm) from the top of
the lower flange of the LH channel as shown in Figure 2.
2. Make sure that the air system support fitting is aligned to the
FWD backup fitting within ±0.020 in (0.51 mm) on each side
of the LH channel. Refer to Figure 7, section A−A.
3. Make sure that the air system support fitting is positioned so
that when its horizontal row of fasteners are installed, the
Hi−Lites head or collar edge will clear the radius of the air
system support fitting. Refer to Figure 7.
(d) Transfer drill the four existing holes from the LH channel through the air
system support fitting. Refer to Figure 7.
NOTE: Make sure that the holes are drilled so that the Hi−Lites head or
collar will clear the radius of the air system support fitting.
(e) Put the AFT back−up fitting, Part No. GC417−0152−3 in position. Refer to
Figure 4.
(f) Transfer drill the pilot holes from the AFT back−up fitting through the LH
channel and through the new AFT lower half rib and secure in place with
clecos. Maintain minimum 2D edge distance and 4−6D pitch, except
where noted. Refer to Figure 3 and Figure 4.
NOTE: Make sure that the holes common to the AFT back−up fitting and
the LH channel are drilled so that there will be a minimum
clearance of 0.060 in (1.52 mm) between the Hi−Lites head or
collar edge and the lightening hole radius on the LH channel.
(g) Transfer drill one hole common to the LH channel and the air system
support fitting through the AFT back−up fitting and secure in place with a
cleco. Maintain 2D minimum edge distance and 4D − 6D pitch.
(h) Drill one hole through the LH channel and the AFT back−up fitting, just
above the air system support fitting (second fastener from the bottom).
NOTE: Make sure that this hole common to the AFT back−up fitting and
the LH channel is drilled so that there will be a minimum
clearance of 0.060 in (1.52 mm) between the Hi−Lites head or
collar edge and the lightening hole radius on the LH channel.
Make sure the fastener head or collar clears the AFT back−up
fitting flange inner radius and the edge of the air system support
fitting. Refer to Figure 3 and Figure 7.
(i) Open all the holes common to the air system support fitting and the parts
that follow: FWD back−up fitting, the AFT back−up fitting and the LH
channel per SRM 51−42−00. Refer to Figure 3, Figure 7, and Table 1 for
fastener call−out.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 9 of 31

### Page 11

(j) Open all the holes common to the FWD back−up fitting and the parts that
follow: the bottom skin and the new FWD upper half rib, Part No.
GD417−1588−3 per SRM 51−42−00. Refer to Figure 2, Figure 5 and
Table 1 for fastener call−out.
(k) Open all the holes common to the AFT back−up fitting and the parts that
follow: the new AFT lower half rib and the LH channel per SRM 51−42−00.
Refer to Figure 3, Figure 4 and Table 1 for fastener call−out.
(l) Dismantle and deburr all the parts.
(m) At the FWD upper half−rib location, Touch up paint the two lower holes in
the LH channel per finish code A032, topcoat color White No. 17875.
Refer to SRM 51−01−04.
(3) Install the new FWD upper half rib, Part No. GD417−1588−3, the new AFT
lower half rib, Part No. GD417−1539−1, the FWD back up fitting, Part No.
GC417−0151−1, the AFT backup fitting, Part No. GC417−0152−3 and the new
air system support fitting, Part No. GC437−0051−1, as follows:
(a) Install the new FWD upper half rib, Part No. GD417−1588−3 as follows:
NOTE: Do not install the fasteners common to the top skin and the three
fasteners common to the FWD back up fitting at this time.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 2, Figure 3 and Table 1 for fastener call out.
(b) Install the new AFT lower half rib, Part No. GD417−1539−1 as follows:
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00, and SRM 51−42−00. Refer
to Figure 3, Figure 4, Figure 5 and Table 1 for fastener call out.
(c) Install the FWD back up fitting, Part No. GC417−0151−1, and the AFT
back up fitting, Part No. GC417−0152−3, as follows:
NOTE: Do not install the fasteners common to the air system support
fitting at this time.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 2, 3, 4, 5 and Table 1 for fastener call out.
(d) Fill the gap between the FWD back up fitting and the existing FWD lower
half−rib, Part No. GD417−1589, with sealant. Refer to Figure 2 and
SRM 51−23−00.
(e) Touch up paint all the fasteners installed inside the rudder quadrant box
per finish code A032, topcoat color White No. 17875. Refer to
SRM 51−01−04.
(f) Lower the top skin on the quadrant box and install as follows:
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 10 of 31

### Page 12

(i) Wet install all the fasteners common to the top skin of the rudder
quadrant box and the parts that follow: the LH and RH channels and
the FWD and AFT half ribs per SRM 51−23−00, and SRM 51−42−00.
Refer to Figure 6 and Table 1 for fastener call−out.
NOTE: For Hi−Lites installed common to the top skin and the FWD
half rib, maintain a minimum 1.8D and 3.9D pitch.
(g) Install the new air system support fitting, Part No. GC437−0051−1, as
follows:
NOTE: Before you install the new air system support fitting, Part No.
GC437−0051−1, fill the two redundant holes, in the LH channel at
the FWD half rib location, with sealant. Refer to SRM 51−23−00.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 7 and Table 1 for fastener call out.
(h) Fill the gap between the air system support fitting and the lightening hole
flange on the LH channel with sealant. Refer to Figure 7 and
SRM 51−23−00.
(i) Touch up paint all the fasteners installed per finish code A032, topcoat
color White No. 17875. Refer to SRM 51−01−04.
(j) Continue to Paragraph 2.E.
D. Replacement and Reinforcement of the Half Ribs and Replacement of the LH
Channel
NOTE: Due to the complexity of the installation and functions of the whole rudder
quadrant box assembly, quadrant position is crucial to keep a good
alignment. Bombardier Aerospace recommends that the replacement of
the LH channel, Part No. GD417−1520, be performed with the rudder
quadrant box assembly removed from the aircraft.
(1) Remove the rudder quadrant box assembly as follows:
(a) Install rig pins (26), (42) and (44) per Figure 401 of
AMM 27−21−27−000−801 to lock the quadrants.
(b) Loosen the four turnbuckles to allow for removal of the cables from the
quadrant.
(c) Remove the cables and move them away from rudder quadrant box to
prevent damage and temporarily secure in position.
(d) Remove the ECS duct support assembly, Part No. GD437−1426, and
keep the attaching hardware except the cotter pins for later installation.
Discard the cotter pins.
(e) Remove the linear feel unit, Part No. FE263−001. Refer to
AMM 27−21−01−000−802
(f) Remove any clamps that may be holding wires, piping or any other system
provision, to allow for the rudder quadrant box removal from the aircraft.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 11 of 31

### Page 13

(g) Carefully remove the rivets that attaches the rudder quadrant box to the
aircraft structure. Refer to SRM 51−42−00.
(h) Remove the rudder quadrant box from the aircraft and put on clean solid
work benches.
(2) Remove the top skin to have access inside the rudder quadrant box.
NOTE: Be careful not to damage the fastener holes.
(3) Remove bracket, Part No. GD477−1686 installed on the top skin and keep for
later installation.
(4) Put the new FWD upper half rib, Part No. GD417−1588−3, and the new AFT
lower half rib, Part No. GD417−1539−1, in position as follows:
(a) Put the new FWD upper half rib, Part No. GD417−1588−3, in position.
(b) Use existing fastener holes in the LH channel, feel unit brace and existing
FWD lower half rib to drill the fastener holes in the new FWD upper half
rib, Part No. GD417−1588−3, make sure to maintain a minimum 2D edge
distance, except where noted. Refer to Figure 2 and Figure 3.
NOTE: Do not drill the two lower holes from the LH channel in the new
FWD upper half rib. Refer to Figure 3.
(c) Put the new AFT lower half rib, Part No. GD417−1539−1, in position.
(d) Use existing fastener holes in the LH channel, existing AFT upper half rib,
bottom skin and feel unit fitting, to drill the fastener holes in the new AFT
lower half rib, Part No. GD417−1539−1, make sure to maintain a minimum
2D edge distance, except where noted. Refer to Figure 3, Figure 4 and
Figure 5.
(e) Put the top skin on the rudder quadrant box and use the existing fastener
holes in the top skin, to drill the holes for Hi−Lites in the new FWD upper
half rib, Part No. GD417−1588−3, make sure to maintain a minimum 1.8D
edge distance and 3.9D pitch. Refer to Figure 6 and SRM 51−42−36.
(5) Replace the cracked LH channel, Part No. GD417−1520, as follows:
(a) Draw a reference line on the quadrant fitting, Part No. GD417−1522 at the
LH channel bottom edge to give a vertical position of the quadrant fitting.
Refer to Figure 8.
(b) Carefully remove all the rivets that attaches the existing LH channel, Part
No. GD417−1520, to the rudder quadrant box.
(c) Keep for later installation, the bracket, Part No. GD777−1549 installed on
the lower skin common to the LH channel, that holds APU fire extinguisher
line.
(d) Remove the bracket, Part No. GD477−1698 that holds the fairleads for the
hydraulic lines from the cracked LH channel and keep for later installation.
(e) Remove the bracket, Part No. GD437−1599 that holds the ECS duct
support assembly and keep for later installation.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 12 of 31

### Page 14

(f) Put the new LH channel , Part No. GD417−1520−7S in position. Put the
rig pins through the channel and the rudder quadrant fitting, Part No.
GD417−1522, and use the reference line on the quadrant fitting to adjust
the final position of the quadrant fitting. Refer to Figure 9.
NOTE: Make sure the proper position of the LH Channel with the use of
the rig pins, and make sure that the LH and RH Quadrant
Bearing Housings, Part No. GD417−1501 and GD417−1524
respectively, are aligned. Also, make sure that the aft end of the
LH Channel’s bottom flange is aligned to the aft edge of the
bottom skin.
(g) Clamp the new LH channel in position.
(h) Remove the rudder quadrant from the rudder quadrant box, and keep the
attaching hardware except the cotter pins for later installation. Discard the
cotter pins.
(i) Transfer drill all the fastener holes from the top skin, the two bottom skins,
the quadrant fitting, the new half ribs and the internal structure common to
the new LH channel. Secure in place with clecos.
(j) Remove the top skin to get access inside the quadrant box.
(6) Put the FWD back−up fitting, Part No. GC417−0151−1, and the AFT back−up
fitting, Part No. GC417−0152−3 in position as follows:
(a) Put the FWD back up fitting, Part No. GC417−0151−1, in position. Refer to
Figure 2
(b) Transfer drill the pilot holes from the FWD back−up fitting through the new
FWD upper half rib, the new LH channel and the bottom skin, transfer drill
the three existing fastener holes from the FWD half−rib through the FWD
back−up fitting and secure in place with clecos. Maintain minimum 2D
edge distance, except where noted. Refer to Figure 2, Figure 5, and
Figure 7.
(c) Put the AFT back−up fitting, Part No. GC417−0152−3 in position. Refer to
Figure 4.
(d) Transfer drill the pilot holes from the AFT back−up fitting through the new
AFT lower half rib and the new LH channel, Part No. GD417−1520−7S,
secure in place with clecos. Maintain minimum 2D edge distance and
4−6D pitch, except where noted. Refer to Figure 3 and Figure 4.
NOTE: Make sure that the holes common to the AFT back−up fitting and
the LH channel are drilled so that there will be a minimum
clearance of 0.060 in (1.52 mm) between the Hi−Lites head or
collar edge and the lightening hole radius on the LH channel.
Refer to Figure 3 and Figure 7.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 13 of 31

### Page 15

(7) Put the new air system support fitting, Part No. GC437−0051−1, in position as
follows:
(a) Put the air system support fitting, Part No. GC437−0051−1, in position and
transfer drill the pilot holes from the FWD back−up fitting. Make sure you
have minimum 2D edge distance. Refer to Figure 2 and Figure 7.
NOTES: 1. Make sure that the bottom of the air system support fitting is
positioned 0.150 ±0.02 in (3.81 ± 0.50 mm) from the top of
the lower flange of the LH channel as shown in Figure 2.
2. Make sure that the air system support fitting is aligned to the
FWD backup fitting within ±0.020 in (0.51 mm) on each side
of the LH channel. Refer to Figure 7, section A−A.
3. Make sure that the air system support fitting is positioned so
that when its horizontal row of fasteners are installed, the
Hi−Lites head or collar edge will clear the radius of the air
system support fitting. Refer to Figure 7.
(b) Drill the four horizontal holes through the air system support fitting, the LH
channel and also through the AFT back−up fitting (1 location). Refer to
Figure 7.
NOTE: Make sure that the holes are drilled so that the Hi−Lites head or
collar will clear the radius of the air system support fitting.
(c) Drill one hole through the LH channel and the AFT back−up fitting, just
above the air system support fitting (second fastener from the bottom).
NOTE: Make sure that this hole common to the AFT back−up fitting and
the LH channel is drilled so that there will be a minimum
clearance of 0.060 in (1.52 mm) between the Hi−Lites head or
collar edge and the lightening hole radius on the LH channel.
Make sure the fastener head or collar clears the AFT back−up
fitting flange inner radius and the edge of the air system support
fitting. Refer to Figure 3 and Figure 7.
(d) Open all the holes common to the air system support fitting and the parts
that follow: FWD back−up fitting, the AFT back−up fitting and the LH
channel per SRM 51−42−00. Refer to Figure 3, Figure 7, and Table 1 for
fastener call−out.
(e) Open all the holes common to the FWD back−up fitting and the parts that
follow: the bottom skin and the new FWD upper half rib, Part No.
GD417−1588−3 per SRM 51−42−00. Refer to Figure 2, Figure 5 and
Table 1 for fastener call−out.
(f) Open all the holes common to the AFT back−up fitting and the parts that
follow: the new AFT lower half rib, Part No. GD417−1539−1, and the LH
channel per SRM 51−42−00. Refer to Figure 3, Figure 4 and Table 1 for
fastener call−out.
(g) Dismantle and deburr all the parts.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 14 of 31

### Page 16

(8) Install the new FWD upper half rib, Part No. GD417−1588−3, the new AFT
lower half rib, Part No. GD417−1539−1, the FWD back up fitting, Part No.
GC417−0151−1, the AFT backup fitting, Part No. GC417−0152−3, the new air
system support fitting, Part No. GC437−0051−1, and the new LH channel, Part
No. GD417−1520−7S, as follows:
(a) Install the new LH channel, Part No. GD417−1520−7S, as follows:
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Appendix 2 Parts and Fastener call out.
NOTES: 1. Make sure to install the bracket, Part No. GD777−1549
for the APU fire extinguisher line, that was removed
from the lower skin common to the LH channel.
2. Make sure to install the quadrant fitting, Part No.
GD417−1522 and the bracket assembly, Part No.
GD437−1599 that were previously removed from the
cracked LH Channel.
(b) Install the new FWD upper half rib, Part No. GD417−1588−3 as follows:
NOTE: Do not install the three fasteners common to the FWD back up
fitting at this time.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 2, Figure 3 and Table 1 for fastener call out.
(c) Install the new AFT lower half rib, Part No. GD417−1539−1 as follows:
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00, and SRM 51−42−00. Refer
to Figure 3, Figure 4, Figure 5 and Table 1 for fastener call out.
(d) Install the FWD back up fitting, Part No. GC417−0151−1, and the AFT
backup fitting, Part No. GC417−0152−3, as follows:
NOTE: Do not install the fasteners common to the air system support
fitting at this time.
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 2, 3, 4, 5 and Table 1 for fastener call out.
(e) Fill the gap between the FWD back up fitting and the existing FWD lower
half−rib, Part No. GD417−1589, with sealant. Refer to Figure 2 and
SRM 51−23−00.
(f) Touch up paint all the fasteners installed inside the rudder quadrant box
per finish code A032, topcoat color White No. 17875. Refer to
SRM 51−01−04.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 15 of 31

### Page 17

(g) Put the top skin in position on the quadrant box.
(h) Wet install all the fasteners common to the top skin of the rudder quadrant
box and the parts that follow: the LH and RH channels, the FWD and AFT
half ribs, and other internal structure of the rudder quadrant box per
SRM 51−23−00, and SRM 51−42−00. Refer to Table 1, Figure 6 and
Appendix 2 for Parts and Fastener call−out.
NOTES: 1. For Hi−Lites installed common to the top skin and the FWD
half rib, maintain a minimum 1.8D and 3.9D pitch.
2. Make sure to install the bracket assembly, Part No.
GD477−1686, that was previously removed from the top
skin.
(i) Install the new air system support fitting, Part No. GC437−0051−1, as
follows:
(i) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(ii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Figure 7 and Table 1 for fastener call out.
(j) Fill the gap between the air system support fitting and the lightening hole
flange on the LH channel with sealant. Refer to Figure 7 and
SRM 51−23−00.
(k) Install the bracket, Part No. GD477−1698 for the fairlead support that was
removed from the cracked LH channel. Refer to the removed LH channel
for position reference, and to Appendix 2 for fastener call out.
(l) Touch up paint all the fasteners installed per finish code A032, topcoat
color White No. 17875. Refer to SRM 51−01−04.
(m) Install the rudder quadrant box back in the aircraft as follows:
(i) Put the rudder quadrant box in position, secure in position with clecos
on the RH side, FWD top skin and AFT bottom skin.
(ii) On the LH side, at the FWD and AFT attachment point, transfer drill
existing fastener holes through the new LH channel, Part No.
GD417−1520−7S. Refer to Appendix 2 for fastener call out.
(iii) Detach the rudder quadrant box from the structure.
(iv) Deburr the fastener holes.
(v) Faying surface seal mating surfaces. Refer to SRM 51−23−00.
(vi) Put the rudder quadrant box in position.
(vii) Wet install fasteners per SRM 51−23−00 and SRM 51−42−00. Refer
to Appendix 2 for fastener call out.
(n) Install the rudder quadrant in the rudder quadrant box with the previously
removed hardware and new cotter pins.
(o) Install the linear feel unit, Part No. FE263−001. Refer to
AMM 27−21−01−400−802.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 16 of 31

### Page 18

(p) Install the ECS duct support assembly, Part No. GD437−1426 with the
previously removed hardware and the new cotter pins.
(q) Install the rudder control cables on the quadrant. Refer to
AMM 27−21−27−400−801.
NOTE: Make sure that you tension the cables for a minimum of 24 hours.
(r) Do the Functional Test of the Rudder Cable Tension. Refer to
AMM 27−21−27−720−801.
(s) Do the Functional Test of the Rudder Control System. Refer to
AMM 27−21−00−720−801.
(t) Install all the clamps that are holding wires, piping or any other system
provision, that were removed to allow the rudder quadrant box removal.
(u) Continue to Paragraph 2.E.
E. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) If removed for access, install the APU Discharge Line, Part No. GD774−1009.
Refer to AMM 26−21−29−400−801.
(3) Connect the connector of the tail strobe−light power supply, Part No.
8ES456038−03. Refer to AMM 33−44−01−400−802.
(4) Install the strut assembly, Part No. GD417−1530, with the previously removed
hardware and use a new cotter pin.
(5) Install the ECS duct rod assembly, Part No. GD437−1590, with the previously
removed hardware and use a new cotter pin.
(6) Install the LH bleed duct, Part No. GG468−4065. Refer to
AMM 36−11−61−400−801.
(7) Install the APU fuel line, Part No. GD428−1019, with the previously removed
hardware.
NOTE: Make sure to do bonding test of the APU fuel line. Refer to
SPM51−80−00−760−801
(8) If removed from hydraulic lines to allow for movement, install fairleads (qty 3),
Part No. GD478−1001, with the previously removed hardware.
(9) Start the APU. Refer to AMM 49−10−00−866−801.
(10) Operate the APU with no load for a minimum of two minutes.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 17 of 31

### Page 19

WARNING: BE CAREFUL WHEN YOU ARE BELOW THE APU ACCESS
DOORS OR NEAR THE APU DRAIN OPENINGS. VERY HOT
FLUIDS CAN COME OUT OF THE DRAIN OPENINGS. THIS CAN
OCCUR DURING AN APU START SEQUENCE, WHILE THE APU
OPERATES, OR AT THE APU SHUTDOWN (AND A SHORT TIME
AFTER). THIS CAN CAUSE INJURY TO PERSONS.
(11) Do a visual check for fuel leaks at the fuel line end connections. No fuel leaks
are permitted.
(12) Do a normal APU shutdown. Refer to AMM 49−10−00−866−802.
(13) Close the aft equipment−compartment door 311BB.
F. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
Kit 700K53−6010 is necessary to do this Service Bulletin and contains the parts
that follow:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
-
DISPOSITION
B0203013−08 41 Nut,
Self−Locking
− −
B0206001AG5−2 24 Hi−Lite − −
B0206001AG5−3 9 Hi−Lite − −
B0206001AG5−4 6 Hi−Lite − −
B0206001AG5−5 5 Hi−Lite − −
B0206001AG5−6 1 Hi−Lite − −
B0206016CY5 3 Collar − −
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 18 of 31

### Page 20

NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
-
DISPOSITION
GC417−0151−1 1 FWD
Back−Up
Fitting
− −
GC417−0152−3 1 AFT Back−Up
Fitting
− −
GC437−0051−1 1 Air System,
Support Fitting
Assembly
GD437−1585−1 Discard
GD417−1539−1S 1 Half−Rib AFT GD417−1539−1 Discard
GD417−1588−3S 1 Half−Rib,
FWD
GD417−1588−3 Discard
HST1094−5 1 Collar − −
MS20470AD4−4A 40 Rivet, Solid − −
MS20470AD4−5A 4 Rivet, Solid − −
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
The part that follows may be necessary to do this Service Bulletin and is available
from Bombardier Aerospace Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
GD417−1520−7S 1 LH Channel GD417−1520 Discard
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 19 of 31

### Page 21

DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Alodine 1200S MIL−DTL−81706 As Necessary Code: A
Compound
Sealing
CT:
B1/2=30 hours
B2=48 hours
B4=84 hours
Pro Seal 870
Class B
MIL−PRF−81733
Type II, Class 1,
Grade A
As Necessary Code: B
Compound
Sealing
CT:
C48=56 days
Pro Seal 870
Class C
MIL−PRF−81733
Type IV, Class 1,
Grade A
As Necessary Code: B
FR Primer BAMS 565−001 As Necessary Code: C
Polyurethane,
Topcoat
White Gloss
#17875 (Ref
Fed. Std 595)
BAMS 565−002 As Necessary Code: C
RTV Silicone Dow Corning
RTV 3145
MIL−A−46146 As Necessary Code: D
Tape,
Insulation,
MIL−I−19166 As Necessary Code: E
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 20 of 31

### Page 22

SUPPLIERS ADDRESSES BY CODES
Code: A
Henkel Corp.
One Henkel Way
Rocky Hill, CT 06067
U.S.A.
Tel.: 1−860−571−5100
www.henkel−northamerica.com
Code: B
PRC−Desoto International
5676 Timberlea Blvd.
Mississauga, Ontario
Canada, L4W 4M6
Tel.: (905) 629−7999
www.ppgaerospace.com
Code: C
Tempo Paint and Varnish Co.
205 Fenmar Dr.
Weston, Ontario
M9L 2X4
Canada
Tel.: (416) 746−2233
www.tempo−aerospace.com
Code: D
Dow Corning Corp.
2200 Salsburg Road W
Auburn, MI 48611
U.S.A.
www.dow.com
Code: E
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 21 of 31

### Page 23

TABLE 1 − FASTENER CALL OUT
ITEM
NO. PART NUMBER DESCRIPTION
1 B0206001AG5−2 HI−LITE, PIN
2 B0206001AG5−3 HI−LITE, PIN
3 B0206001AG5−4 HI−LITE, PIN
4 B0206001AG5−5 HI−LITE, PIN
5 B0206001AG5−6 HI−LITE, PIN
6 B0203013−08 NUT, SELF LOCKING
7 HST1094−5 COLLAR
8 MS20470AD4−4A RIVET, SOLID
9 MS20470AD4−5A RIVET, SOLID
10 B0206016CY5 COLLAR
MODEL BD−700−1A10 (BD−700)
Basic Issue: Oct 01/2018 700−53−052
Page 22 of 31

### Page 24 (OCR)

BOMBARDIER
GLOBAL EXPRESS
OMBARDIE
GLOBAL EXPRESSXR
MODEL BD-700-1A10 (BD-700)
LOCATION OF EXISTING
FWD UPPER HALF RIB GD417-1588-3
LOCATION OF EXISTING
AFT LOWER HALF RIB GD417-1539-1
Alliec
Signal
FLEr
OPE
FWD
GSB5340_001
Figure 1 - Removal of Half-Ribs
Basic Issue: Oct 01/2018  700-53-052
Page 23 of 31

### Page 25

GSB5340_011
NOTE
1 Maintain minimum 1.8D edge distance and 3.9D pitch. Pick−up existing fastener holes.
LEGEND
B0206001AG5−2 + B0203013−08
B0206001AG5−3 + B0203013−08
MS20470AD4−4A
MS20470AD4−5A
2
68
8
9
0.150 ± 0.02 in
(3.81 ± 0.50 mm)
FEEL UNIT FITTING
(GD417−1523)
1
6
FILL GAP WITH
SEALANT
1
FWD BACK−UP FITTING
(GC417−0151−1)
FEEL UNIT BRACE
(GD417−1543)
FWD LOWER
HALF RIB
(GD417−1589)
NEW FWD UPPER HALF RIB
(GD417−1588−3)
AIR SYSTEM
SUPPORT FITTING
(GC437−0051−1)
MODEL BD−700−1A10 (BD−700)
Figure 2 − Forward  Half−Ribs, View Looking Aft
Basic Issue: Oct 01/2018 700−53−052
Page 24 of 31

### Page 26

GSB5340_021
NOTES
If existing hole on LH channel is 0.160 − 0.164 in (4.064 − 4.165mm), install MS20470AD5−(*)A rivet, in lieu1
of MS20470AD4−(4)A, maintain 1.6D edge distance 3.7D pitch.
2 Do not drill holes and install fasteners.
3 Maintain minimum 0.060 in (1.52mm) clearance between fastener head or collar and lightening hole radius on
LH channel.
4 Maintain minimum 2D edge distance and 3.8D pitch.
LEGEND
MS20470AD4−4A
B0206001AG5−4 + B0203013−08
5 Make sure there is clearance between fastener head or collar and air system support fitting.
1
2
FORWARD BACK−UP
FITTING
(GC417−0151−1)
3
6
8
84
3
1
3
NEW AFT LOWER
HALF RIB
(GD417−1539−1)
AFT BACK−UP
FITTING
(GC417−0152−3)
NEW FWD UPPER
HALF RIB
(GD417−1588−3)
LH CHANNEL
(GD417−1520)
5
MODEL BD−700−1A10 (BD−700)
Figure 3 − LH Channel, View Looking Outboard
Basic Issue: Oct 01/2018 700−53−052
Page 25 of 31

### Page 27

GSB5340_031
LEGEND
MS20470AD4−4A
B0206001AG5−2 + B0203013−08
UP
LH
0.030 in
(0.76 mm)
MINIMUM
8
1
6
AFT BACK−UP
FITTING
(GC417−0152−3)
AFT UPPER HALF RIB
(GD417−1539)
0.065 ± 0.030 in
(1.65 ± 0.76 mm)
AIR SYSTEM
SUPPORT FITTING
(GC437−0051−1)
LH CHANNEL
(GD417−1520)
NEW AFT LOWER
HALF RIB
(GD417−1539−1)
BOTTOM SKIN
(GD417−1526)
MODEL BD−700−1A10 (BD−700)
Figure 4 − Aft Half−Ribs, View Looking Aft
Basic Issue: Oct 01/2018 700−53−052
Page 26 of 31

### Page 28

GSB5340_041
LEGEND
B0206001AG5−2 + B0203013−08
B0206001AG5−3 + B0203013−08
MS20470AD4−4A
B0206001AG5−3 + B0206016CY5
2
6
1
6
2
10
8
8
BL0.00
AFT
LH
FEEL UNIT FITTING
(GD417−1523)
NEW AFT LOWER
HALF−RIB
(GD417−1539−1)
AFT BACK−UP
FITTING
(GC417−0152−3)
AIR SYSTEM
SUPPORT FITTING
(GC437−0051−1)
FORWARD BACK−UP
FITTING
(GC417−0151−1)
BOTTOM SKIN
(GD417−1526)
MODEL BD−700−1A10 (BD−700)
Figure 5 − Bottom Skin, View Looking Up
Basic Issue: Oct 01/2018 700−53−052
Page 27 of 31

### Page 29

GSB5340_051
LEGEND
B0206001AG5−2 + B0203013−08
MS20470AD4−()A
NOTE
Maintain minimum 1.8D edge distance and 3.9D pitch.1
AFTLH
BL0.00
1
6
TOP SKIN
(GD417−1525) 1
NEW FWD UPPER
HALF RIB
(GD417−1588−3)
RH CHANNEL
(GD417−1598)
AFT UPPER
HALF RIB
(GD417−1539)
LH CHANNEL
(GD417−1520)
AIR SYSTEM
SUPPORT FITTING
(GC437−0051−1)
MODEL BD−700−1A10 (BD−700)
Figure 6 − Top Skin, View Looking Down
Basic Issue: Oct 01/2018 700−53−052
Page 28 of 31

### Page 30

3
6
5
7
GSB5340_061
LEGEND
B0206001AG5−5 + B0203013−08
B0206001AG5−4 + B0203013−08
B0206001AG5−6 + HST1094−5
FEEL UNIT FITTING
(GD417−1523)
1
1
NOTE
Make sure the fastener head or collar edge clears the fillet radius of the air system support fitting.1
LH CHANNEL
(GD417−1520)
4
6
FILL GAP
WITH SEALANT
AFT BACK−UP
FITTING
(GC417−0152−3)
NEW FWD UPPER
HALF RIB
(GD417−1588−3)AIR SYSTEMSUPPORT FITTING
(GC437−0051−1)
2
2
LH CHANNEL
(GD417−1520)
FWD BACK UP
FITTING
(GC417−0151−1)
AIR SYSTEM
SUPPORT FITTING
(GC437−0051−1)
NEW AFT LOWER
HALF RIB
(GD417−1539−1)
2 Make sure indicated edges of air system support and FWD back−up fitting are aligned within
±0.020 in (0.51 mm) on each side of LH channel as shown.
MODEL BD−700−1A10 (BD−700)
Figure 7 − Air Systems Support Fitting
Basic Issue: Oct 01/2018 700−53−052
Page 29 of 31

### Page 31 (OCR)

BOMBARDIER
GLOBAL EXPRESS
OMBARDIEI
GLOBAL EXPRESS×R
MODEL BD-700-1A10 (BD-700)
BEARING HOUSING
ASSEMBLY
(GD417-1501)
QUADRANT
LH CHANNEL  RUDDER QUADRANT  FITTING
(GD417-1520)  POSITION REFERENCE  (GD417-1522)
LINE
GSB5340_091
Figure 8 - Rudder Quadrant Position Reference Line
Basic Issue: Oct 01/2018  700-53-052
Page 30 of 31

### Page 32 (OCR)

BOMBARDIER
GLOBAL EXPRESS
OMBARDIE
GLOBAL EXPRESSXR:
MODEL BD-700-1A10 (BD-700)
BEARING HOUSING
ASSEMBLY
RUDDER  QUADRANT  (GD417-1501)
NEW LH CHANNEL  QUADRANT
(GD417-1520-7)  FITTING
(GD417-1522)
LH CHANNEL INSTALLATION
GSB5340_101
Figure 9 - LA Channel Installation
Basic Issue: Oct 01/2018  700-53-052
Page 31 of 31

### Page 33

700−53−052 Basic Oct 01/2018
MODIFICATION − AFT FUSELAGE − REPLACEMENT AND
REINFORCEMENT OF THE RUDDER QUADRANT BOX ASSEMBLY HALF
RIBS
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 34

SERVICE BULLETIN INCORPORATION SHEET − "700−53−052"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−53−052 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

### Page 35

APPENDIX 1 
Oct 01/ 2018 700-53-052 
 Page 1 of 5 
EDDY CURRENT INSPECTION REQUIREMENTS 
INSPECTION # 1 
 
INSPECT ALL FASTENER HOLES AS SHOWN ON THE LH CHANNEL GD417-1520 
(FIGURE 2) USING BOLT-HOLE EDDY CURRENT METHOD: 
 
PERFORM BOLT-HOLE EDDY CURRENT INSPECTION AS PER NDTM PART 1, 
SECTION 6E. 
 
FOR INSPECTION USE THE FOLLOWING EQUIPMENT OR EQUIVALENT: 
 
INSTRUMENT: PHASEC 3D OR NORTEC 600. 
PROBE BHEC: EC-NDT S06R2 0.115"- 0.135" (100KHZ - 2 MHZ)  
                          EC-NDT S06R2 0.156"- 0.187" (100KHZ - 2 MHZ) 
      NOTE: USE THESE PROB ES AS APPLICABLE DEPENDING ON HOLE 
DIAMETER. 
 
CALIBRATION BLOCK: NRK-3A 
MINIDRIVE: GE NO. 33A100 
CABLE: GE 33A103 
NOTE:  EXISTING AIR SYSTEMS SUPPOR T FITTING (GD437-1585), FWD HALF-
RIB (GD417-1588), AFT HALF-RIB (GD417-1539) AND THEIR 
ATTACHMENT FASTENERS MUST BE REMOVED PRIOR TO THIS 
INSPECTION.

### Page 36

APPENDIX 1 
Oct 01/ 2018 700-53-052 
 Page 2 of 5 
INSPECTION # 2 
 
PERFORM HIGH FREQUENCY EDDY CURRENT INSPECTION AROUND HOLES ON 
THE LH CHANNEL GD417-1520 (FIGURE 2) PER NDTM PART 1, SECTION 6D:  
 
MAKE A FULL CIRCULAR (360°) SCAN AROUND EACH HOLE AS INDICATED IN 
FIGURE 2.  
REPEAT THE SCAN FROM THE OPPOSITE SIDE OF THE LH CHANNEL WEB. 
 
FOR INSPECTION USE THE FOLLOWING EQUIPMENT OR EQUIVALENT: 
 
INSTRUMENT: PHASEC 3D OR NORTEC 600 
PROBE: PAB 4560-1.0/.083  
CALIBRATION BLOCK: SRS-0824A/7075T6 
 
NOTE:   WHEN SCANNING AROUND HO LES, MAKE SURE THAT PROBE TO 
HOLE DISTANCE IS LESS THAN 0.080" (2.0 MM) OR AS CLOSE AS 
POSSIBLE TO THE EDGE OF THE HOLE WITHOUT OBTAINING AN 
EDGE SIGNAL.  
 
 
NOTE:  EXISTING AIR SYSTEMS SUPPOR T FITTING (GD437-1585), FWD HALF-
RIB (GD417-1588), AFT HALF-RIB (GD417-1539) AND THEIR 
ATTACHMENT FASTENERS MUST BE REMOVED PRIOR TO THIS 
INSPECTION.

### Page 37

APPENDIX 1 
Oct 01/ 2018 700-53-052 
 Page 3 of 5 
 
INSPECTION # 3 
 
PERFORM HIGH FREQUENCY EDDY CURRENT INSPECTION SCANNING THE 
INDICATED SURFACE OF THE LH CHANNEL WEB GD417-1520 (FIGURE 3), PER 
NDTM PART 1, SECTION 6D: 
  
MAKE A SERIES OF PARALLEL SCANS PERPENDICULAR TO THE CRACK 
DIRECTION OF PROPAGATION. REFER TO FIGURE 3. (TWO PERPENDICULAR 
SCANS ARE REQUIRED TO COMPLETE THE INSPECTION OF THE AREA 
SHOWN IN FIGURE 3).  
 
START SCANNING FROM THE TANGENT POINT OF THE LOWER RADIUS.  
REPEAT THE SCAN FROM THE OPPOSITE SIDE OF THE LH CHANNEL WEB. 
 
FOR INSPECTION USE THE FOLLOWING EQUIPMENT OR EQUIVALENT: 
 
INSTRUMENT: PHASEC 3D OR NORTEC 600. 
PROBE: PAB 4560-1.0/.083  
CALIBRATION BLOCK: SRS-0824A/7075T6. 
NOTE:  EXISTING AIR SYSTEMS SUPPORT FITTING (GD437-1585), FWD HALF-
RIB (GD417-1588), AND THEIR ATTACHMENT FASTENERS MUST BE 
REMOVED PRIOR TO THIS INSPECTION.

### Page 38

APPENDIX 1 
Oct 01/ 2018 700-53-052 
 Page 4 of 5

### Page 39 (OCR)

BOMBARDIER
APPENDIX 1
_H CHANNE
D417-152
SUPPORT FITTING  EXISTING AIR SYSTEMS  OUTLINE OF
GD437-1585
' INSPECTION #2
TYPICAL
INSPECTLAN *1
FIGURE 2
IT AIR SOSTEN SUPPORT ENTING LOCATION  AFT
SUPPOR
CD417-1520
-1.5
• INSPECTION +3
TYPICAL CRACK LOCATION AND
DIRECTION CF PROPAGATION
FIGURE 3
AT AER SOSTENS SUPPORT FITTING LOCATION  - AF T
Oct 01/ 2018  700-53-052
Page 5 of 5

### Page 40

APPENDIX 2 
Oct 01/2018 700-53-052 
 Page 1 of 3 
RUDDER QUADRANT BOX – LH CHANNEL REPLACEMENT – FASTENER CALL OUT

### Page 41

APPENDIX 2 
Oct 01/2018 700-53-052 
 Page 2 of 3

### Page 42

APPENDIX 2 
Oct 01/2018 700-53-052 
 Page 3 of 3

### Page 43

APPENDIX 3 
Oct 01/2018 700-53-052 
 Page 1 of 4 
DETAILED VISUAL INSPECTION REQUIREMENTS

### Page 44

APPENDIX 3 
Oct 01/2018 700-53-052 
 Page 2 of 4

### Page 45

APPENDIX 3 
Oct 01/2018 700-53-052 
 Page 3 of 4

### Page 46

APPENDIX 3 
Oct 01/2018 700-53-052 
 Page 4 of 4

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
