# Bombardier Service Bulletin 700-53-5010

Copy: No revision named ("SB 700-53-5010 Basic"), 14 pages: PDF https://openairdocs.org/files/sha256/8f/7a/8f7ae6f6d16878aa9bda193068235b15108d3d197eb5f89275a7dcd178d099b4; text https://openairdocs.org/service-documents/bombardier/sb-700-53-5010/file/8f7ae6f6d168.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0796; AD 2018-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-53-5010
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-53-5010

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2018-25-07](https://openairdocs.org/ad/2018-25-07.md), effective Jan 15, 2019: No revision named

## Text (14 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0796; AD 2018-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/REWORK — BELLY FAIRINGS — INSPECT FORWARD AND
MIDDLE ACCESS PANEL (181BB) AND (183BB) FOR DRAINAGE HOLE BLOCKAGE,
AND IF NECESSARY REMOVE SEALANT
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 750 flight hours or 20 months,
whichever comes first, from this Service
Bulletin release date (Basic Issue)
EFFECTIVITY: A/C Serial No. 9386, 9401 and 9445 to 9737
MANPOWER: PART A: 1 man−hour
PART B: 5 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS NOYES
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
SERVICE BULLETIN SUMMARY
www.cic.bombardier.com
MODEL BD−700−1A11 (BD−700)
ATA 53−61
FUSELAGE
Basic Issue: May 17/2017 700−53−5010
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/REWORK — BELLY FAIRINGS — INSPECT FORWARD AND
MIDDLE ACCESS PANEL (181BB) AND (183BB) FOR DRAINAGE HOLE BLOCKAGE,
AND IF NECESSARY REMOVE SEALANT
1. PLANNING INFORMATION
A. Effectivity
BD−700−1A11 aircraft, Serial No. 9386, 9401 and 9445 to 9737.
All other subsequent BD−700−1A11 aircraft are scheduled for the modification in
production (Ref.: Modification Summary 700T810087).
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent action
changes to make sure that this bulletin can be completed.
B. Reason
1. Condition:
The fluid drainage gaps between the fairing and access panels 181BB and
183BB may be obstructed with sealant.
2. Evidence:
The aerodynamic sealant applied on the panel contours obstructs the gaps
provided for the evacuation of fuel/hydraulic fluids from the belly fairing in the
event of a system leakage. As a result, any fluid leakage will be retained inside
the belly fairing and therefore not be observed during daily inspection.
SERVICE BULLETIN
www.cic.bombardier.com
MODEL BD−700−1A11 (BD−700)
ATA 53−61
FUSELAGE
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2017 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: May 17/2017 700−53−5010
Page 1 of 11
This Service Bulletin is available at:

### Page 3

3. Objective/Benefit:
The drain channels allow detection of local fuel/hydraulic fluid leakage. They
prevent the accumulation of flammable fluids in the belly fairing, and the
potential subsequent ignition of these accumulated fluids. This Service Bulletin
is released to inspect the aerodynamic sealant and, if necessary, locally remove
the sealant to allow for drainage.
C. Description
This Service Bulletin gives instructions in PART A, to :
− Inspect the aerodynamic sealant of access panels 181BB and 183BB.
This Service Bulletin gives instructions in PART B, to:
− Remove access panels 181BB and 183BB,
− Locally remove the sealant at the location of the 12 drain gaps,
− Install access panels 181BB and 183BB,
− Apply aerodynamic sealant as per engineering drawing, and
− Check the aerodynamic smoothness of access panels 181BB and 183BB.
D. Compliance
Recommended in less than 750 flight hours or 20 months, whichever comes first
from this Service Bulletin release date (Basic Issue).
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA in
accordance with established procedures.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 2 of 11

### Page 4

F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−5002.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
3. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
PART A: 1 man−hour is necessary to do this special check.
Bombardier Aerospace does not pay for the labor to do PART A of this Service
Bulletin.
PART B: 5 man−hours are necessary to do this rework.
The labor required to do PART B of this Service Bulletin is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 750 flight hours or 20 months,
whichever comes first from this Service Bulletin release date (Basic Issue).
G. Material − Cost and Availability
No kit or parts are necessary to do this special check/rework. For material data,
refer to Paragraph 3.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 3 of 11

### Page 5

H. Tooling
The equipment and tools listed below are necessary to do this special
check/rework:
GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Sealant Gun
Commercially Available − Wrench, Torque 15 to 25
lbf in (1.70 to 2.82 Nm)
NOTES: 1. Refer to the Global 5000 Featuring Global Vision Flight Deck
Illustrated Tool and Equipment Manual (ITEM) to make sure that you
use the correct equipment configuration.
2. Refer to the Liability Statement for the GVFD for acceptable GSE
equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI), C−01692,
Rev. −−.
− Bombardier Aerospace, Modification Summary, 700T810087, Rev. A3.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
− Bombardier Aerospace, Drawing GS298−0001, NIEO R130270.
− Global 5000 Featuring Global Vision Flight Deck BD−700 Aircraft Maintenance
Manual (AMM), Chapters 6 and 51.
− Global 5000 Featuring Global Vision Flight Deck BD−700 Structural Repair
Manual (SRM), Chapter 51.
L. Other Publications Affected
None.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 4 of 11

### Page 6

M. Equivalent Service Bulletin
− For the Global Express and Global Express XRS BD−700−1A10 aircraft, use
SB 700−53−051.
− For the Global 5000 BD−700−1A11 aircraft, use SB 700−1A11−53−026.
− For the Global 6000 BD−700−1A10 aircraft, use SB 700−53−6009.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 5000
BD−700−1A11 Featuring Global Vision Flight Deck Aircraft Maintenance
Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck Aircraft
Maintenance Manual (AMM), Chapter 6.
A. Aircraft Setup
No setup required.
B. PART A − Inspection of Sealant
(1) Check the aerodynamic sealant around access panels 181BB and 183BB.
(2) If the access panels 181BB and 183BB do not have aerodynamic sealant at
the locations indicated in Figure 1, Section C−C, you have met the intent of this
Service Bulletin. Continue to Paragraph 2.E. Recording, and make an entry in
the aircraft log book for PART B as N/A.
(3) If the access panels 181BB or 183BB have aerodynamic sealant on all edges
as indicated in Figure 1, Section D−D, do PART B of this Service Bulletin.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 5 of 11

### Page 7

exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
SSB5361_002
ACCESS PANEL 181BB ACCESS PANEL 183BB
SEALING
PAD
SEALING
PAD
NO AERODYNAMIC SEAL APPLIED
(TYP AFT EDGE OF PANEL 181BB)
(TYP ALL EDGES OF PANEL 183BB)
AERODYNAMIC SEAL APPLIED
(NOT APPLICABLE TO PANEL 183BB)
SECTION − SECTION −
Aerodynamic Sealant
Figure 1
C. PART B − Rework − Removal of Aerodynamic Sealant
(1) Remove access panels 181BB and 183BB. Refer to
AMM 53−61−19−000−801.
(2) Remove all traces of sealant from access panels 181BB and 183BB. Refer to
SPM Chapter 51−23−00.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 6 of 11

### Page 8

(3) Locally remove the sealant from the aircraft structure at the four locations of
the drain gaps, aft of access panel 181BB. Refer to Figure 2. Refer to SPM
Chapter 51−23−00.
(4) Locally remove the sealant from the aircraft structure at the eight locations of
the drain gaps, aft and forward of access panel 183BB. Refer to Figure 2.
Refer to SPM Chapter 51−23−00.
exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
FSB5361_001
ACCESS PANEL 181BB ACCESS PANEL 183BB
DRAIN GAP LOCATIONS
Drain Locations
Figure 2
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 7 of 11

### Page 9

(5) Install access panel 181BB. Refer to AMM 53−61−19−400−801 and Drawing
GS298−0001, NIEO R130270 page 2.
NOTE: Omit aerodynamic sealant along the aft edge of access panel 181BB.
(6) Install access panel 183BB. Refer to AMM 53−61−19−400−801 and Drawing
GS298−0001, NIEO R130270 page 3.
NOTE: Do not apply aerodynamic sealant around access panel 183BB.
D. Close−out
(1) Do a check of the aerodynamic smoothness of the access panels 181BB and
183BB. Refer to SRM Chapter 51–14–04.
(2) Remove all tools, equipment and unwanted materials from the work area.
E. Recording
When any PART of this Service Bulletin is completed, make an entry in the aircraft
log and send the attached Incorporation Notice to Bombardier Business Aircraft
Customer Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
No parts required.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Ergonomic
Sealant
Removal Tool
− − As Necessary
for PART B
Code: A
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 8 of 11

### Page 10

DESCRIPTION PART
NO./NAME
SPECIFICATION QUANTITY SUPPLIER
(SEE
NOTE)
Sealing
Compound
− MIL−PRF−81733
Type II, Class 1,
Grade A Pro
Seal 870 B
As Necessary
for PART B
Code: A
Scraper,
Non−Metallic
− − As Necessary
for PART B
Code: B
Spatula (tool
to fair
material)
− − As Necessary
for PART B
Code: B
Tape,
Masking
− − As Necessary
for PART B
Code: B
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
PRC−Desoto International
5676 Timberlea Blvd.
Mississauga, Ontario
Canada, L4W 4M6
Tel.: (905) 629−7999
www.ppgaerospace.com
Code: B
Commercially Available
D. Publications
No publications required.
MODEL BD−700−1A11 (BD−700)
Basic Issue: May 17/2017 700−53−5010
Page 9 of 11

### Page 11 (OCR)

BOMBARDIER
GLOBAL 5000
FEATURING GLOBAL VISION FLIGHT DECK
MODEL BD-700-1A11 (BD-700)
5 IDENTIFIER  X R130270  NIEO  8 SHEET  5 IDENTIFIER  EO Г  NIEO X R130270
ENGINEERING ORDER (EO)  4 DRAWING NUMBER  3 MS CODE  DH  GS298-0001  4 DRAWING NUMBER  3 MS CODE  GS298-0001
DH
APPLY AERODYNAMIC  SEALING ALONG LH, RH AND  FORWARD EDGES OF ACCESS  PANEL GS297-0583 F.NO. 293.  GS297-0582  F NO. 293.
ITEM 183 REF
BOMBARDIER  OMIT AERODYNAMIC SEALING  ALONG AFT EDGE OF ACCESS  PANEL GS297-0582 F.NO. 293.  BT0204-02 MW REV 2004-09
GS298-0001 - Installation of Belly Fairing
(Sheet 1 of 1, Rev. NEO R130270)
Basic Issue: May 17/2017  700-53-5010
Page 10 of 11

### Page 12 (OCR)

BOMBARDIER
GLOBAL 5000
FEATURING GLOBAL VISION FLIGHT DECK
MODEL BD-700-1A11 (BD-700)
5 IDENTIFIER  EO  X R130270  NIEO  8 SHEET  5 IDENTIFIER  EO  NIEO X R130270
ENGINEERING ORDER (EO)  4 DRAWING NUMBER  3 MS CODE  DH  GS298-0001  OMIT AERODYNAMIC SEALING  AROUND PERIPHERY OF ACCESS  PANEL GS297-0122 F.NO. 178.  4 DRAWING NUMBER  3 MS CODE  GS298-0001
DH
GS297-0122  ENO. 178.
CErRIL ON LE
® E
BOMBARDIER  BT0204-02 MW REV 2004-09
GS298-0001 - Installation of Belly Fairing
(Sheet 1 of 1, Rev. NIEO R130270)
Basic Issue: May 17/2017  700-53-5010
Page 11 of 11

### Page 13

700−53−5010 Basic May 17/2017
SPECIAL CHECK/REWORK — BELLY FAIRINGS — INSPECT FORWARD
AND MIDDLE ACCESS PANEL (181BB) AND (183BB) FOR DRAINAGE
HOLE BLOCKAGE, AND IF NECESSARY REMOVE SEALANT
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 14

SERVICE BULLETIN INCORPORATION SHEET − "700−53−5010"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
700−53−5010 BASIC
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
