# Bombardier Service Bulletin 700-53-7547

Copy: No revision named ("Bombardier Inc. Service Bulletin 700-53-7547 Basic Issue"), 16 pages: PDF https://openairdocs.org/files/sha256/d3/94/d394ffc00877722f99f22d49264f0778d858bb321833cf0364d9fa9353ba9dbf; text https://openairdocs.org/service-documents/bombardier/sb-700-53-7547/file/d394ffc00877.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1485; AD 2023-03-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-53-7547
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-53-7547

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-03-08](https://openairdocs.org/ad/2023-03-08.md), effective Apr 3, 2023: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-53-7547/proposed.md).

## Text (16 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1485; AD 2023-03-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/MODIFICATION – AFT FUSELAGE SKIN AND ACCESS PANELS –
INSPECT FOR MISSING RIVETS AT AFT FUSELAGE STRINGER 19
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 70020 to 70039, 70041, 70046 and 70047
MANPOWER: 5 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
AIRWORTHINESS LIMITATIONS (AWL) NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: NA
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−2A12 (BD−700)
ATA 53−42
FUSELAGE
Basic Issue: Jul 21/2021 700−53−7547
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/MODIFICATION – AFT FUSELAGE SKIN AND ACCESS PANELS –
INSPECT FOR MISSING RIVETS AT AFT FUSELAGE STRINGER 19
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. For any technical issues, contact CSE, Technical Support, Global Express
by e−mail at SRPSA@aero.bombardier.com.
A. Effectivity
BD−700−2A12 aircraft Serial No. 70020 to 70039, 70041, 70046 and 70047.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
In the aft fuselage LH panel assembly, three rivets are missing on stringer 19
attaching to skin between FS945.75 and FS961.45 (FWD engine mount frame).
Due to missing rivets, skin may be subjected to inter−rivet buckling condition
repeatedly, resulting in visible aircraft damage.
2. Objective/Benefit:
The objective is to inspect for rivets, damages, do any repair if necessary, and if
found missing rivets, install the rivets or fasteners attaching stringer 19 and skin
between FS945.75 and FS961.45.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−2A12 (BD−700)
ATA 53−42
FUSELAGE
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2021 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jul 21/2021 700−53−7547
Page 1 of 13
This Service Bulletin is available at:

### Page 3

C. Description
This Service Bulletin gives instructions to:
− Get access to aft fuselage skin,
− Inspect for missing rivets,
− Inspect for damages,
− Repair any damage if necessary, and
− If necessary, install the rivets or fasteners.
D. Compliance
Specified Time Compliance
Recommended before 2,500 flight cycles or within 36 months from this Service
Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−7502.
2. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
5 man−hours are necessary to do this modification.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 2 of 13

### Page 4

The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 2,500 flight cycles or within
36 months from its release date (Basic Issue).
G. Material − Cost and Availability
No kits are necessary to do this modification. For material data, refer to
Paragraph 3.
The parts in Paragraph 3.B. are necessary to do this modification.
The parts are available at no cost if:
− ordered during new aircraft warranty period, and
− a no−charge purchase order is sent to Bombardier Aviation in less than 2,500
flight cycles or within 36 months from its release date (Basic Issue).
Smart Parts does not pay for this recommended Service Bulletin at any time.
H. Tooling
The equipment and tool listed below is necessary to do this modification.
GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Torque Wrench
NOTES: 1. Refer to the Global 7500 Illustrated Tool and Equipment Publication
(ITEP) to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEP for the G7500 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the AMP, WM, Chapter 20,
then the tools called in the AMP, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 3 of 13

### Page 5

K. References
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−70583,
Rev. −−.
− Bombardier Aviation, Drawing G05360001, Rev. D.
− Bombardier Aviation, Drawing G05362000, Rev. AC.
− Global 7500 Aircraft Maintenance Publication (AMP), Chapters 12, 20, 24, 51,
52, and 53.
− Global 7500, Aircraft Structure Repair Publication (ASRP), Chapter 51.
L. Other Publications Affected
None.
M. Equivalent Service Bulletins
None.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 7500
BD−700−2A12, Aircraft Maintenance Publication (AMP) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 7500 BD−700−2A12 Aircraft Maintenance Publication (AMP),
Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
BD700−A−J24−00−00−00AAA−012A−A.
(2) Obey all oil−system safety precautions. Refer to
BD700−A−J12−14−00−00AAA−012A−A.
(3) Open the aft equipment−compartment door (185KL). Refer to
BD700−A−J52−41−01−00AAA−540A−A.
(4) Get access to aft fuselage skin at stringer 19 between FS945.75 and
FS961.45. Refer to Figure 1.
B. Modification
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and get an approved disposition to complete this Service Bulletin.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 4 of 13

### Page 6

(1) Inspect for rivets, Part No. B0205020AD5−6S (qty 3) on the stringer 19, Part
No. G05362149–101. The rivets are common to Outer Mold Line (OML) skin
between FS945.75 and forward engine mount frame FS961.45.
(a) If the rivets, Part No. B0205020AD5−6S (qty 3), are installed, no further
action is necessary. Go to Paragraph 2.D. (Close−out).
(b) If the rivets, Part No. B0205020AD5−6S (qty 3), are found missing, do the
steps that follow.
(2) For general repair procedures, refer to ASRP
BD700−A−J51−70−04−00AAA−663A−A.
(3) Do a detail visual inspection of the skin, Part No. G05362101−105, stringer 19,
Part No. G05362149−101. Do a detail visual inspection of adjacent fasteners
from inside and outside within 6.00 in. (152.40 mm) radius around missing
rivets. Refer to Figure 1, Detail D and E.
NOTE: Use a magnifier and a flashlight as inspection aids.
(a) If damages are found, submit an SRPSA for analysis and request for
disposition.
(4) Make sure that there are no deformation, gap between stringer and skin,
cracks, lose or additional missing fasteners and other signs of damage.
(a) If damages are found, submit an SRPSA for analysis and request for
disposition.
(b) If no damages are found, do step (5) for solution 1 or step (6) for
solution 2.
(5) Install the rivets, Part No. B0205020AD5−6S (qty 3) per solution 1 as follow;
(a) Remove the aft fairing, Part No. G05384000−001 (185GB). Refer to
BD700−A−J53−67−41−00AAA−520A−A.
(b) Install the rivets, Part No.B0205020AD5−6S (qty 3) per document listed in
Paragraph 1.K. Refer to ASRP BD700−A−J51−42−08−00AAA−078A−A
and Figure 1, Detail F.
(c) Install the aft fairing, Part No.G05384000−001 (185GB). Refer to
BD700−A−J53−67−41−00AAA−720A−A.
(6) Install the fasteners per solution 2 as follows:
(a) Drill pilot holes at two places on stringer 19, Part No. G05362149−101,
through skin, Part No. G05362101−105, and through aft fairing, Part No.
G05384000−001. Refer to Figure 1, Detail H. Drill from inside and make
sure the minimum edge distance is achieved per ASRP
BD700−A−J51−40−04−00AAA−078A−A.
NOTE: Make sure to protect skin with stainless plate between skin and
fairing before trimming.
(b) Trim aft fairing, Part No. G05384000−001. Refer to ASRP
BD700−A−J51−75−11−11AAA−659A−A and Figure 1, Detail J.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 5 of 13

### Page 7

(c) Do an inspection of the skin. If damages are found, submit an SRPSA for
analysis and request for disposition.
(d) With sealant (06−002), wet install the bolts, Part No. B0206002AG5−3
(qty 2) and the nuts, Part No. B0203013−08 (qty 2). Refer to ASRP
BD700−A−J51−42−36−00AAA−078A−A and AMP
BD700−A−J51−23−13−00AAA−690B−A. Make sure the bolts head are
outside and the nuts are inside. Refer to Figure 1, Detail K.
(e) Torque the nuts Part No. B0203013−08 (qty 2) from 15 to 25 lbf·in (1,70 to
2,82 Nm). Refer to BD700−A−J20−50−00−00AAA−711A−A.
(f) Touch up with primer (09−009) and apply top coat on the nuts, Part No.
B0203013−08 (qty 2). Refer to ASRP
BD700−A−J51−01−06−00AAA−257A−A.
(g) Touch up with primer (09−009) and apply top coat on the bolts, Part No.
B0206002AG5−3 (qty 2). Refer to ASRP
BD700−A−J51−01−06−00AAA−257A−A.
(h) Seal the trimmed edge of fairing by applying Hysol EA956 A/B and cure
per manufacturer.
(i) Apply the sealant (06−001) for an aerodynamic seal to the aft fairing, Part
No. G05384000−001. Refer to BD700−A−J51−23−37−00AAA−690B−A.
(j) Apply a layer of epoxy primer (09−009) on sealant and one layer of
polyurethane top coat (09−143). Refer to ASRP
BD700−A−J51−01−06−00AAA−257A−A and
BD700−A−J51−01−08−00AAA−257A−A.
C. Testing
No testing required.
D. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Close the aft equipment−compartment door (185KL). Refer to
BD700−A−J52−41−01−00AAA−740A−A.
E. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Aviation Customer Services
(BACS).
For information, corrections, comments and/or feedback regarding Service Bulletins
released on the Customer Portal, please contact the Service Bulletin Group at the
following email address:
bbad_SBgroup@aero.bombardier.com
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 6 of 13

### Page 8

3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
The parts that follow are necessary to do this Service Bulletin and are available
from Bombardier Aviation Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PART
NO.
INSTRUCTIONS
- DISPOSITION
B0203013−08
(See Note 5)
2 NUT, SELF
LOCKING
− −
B0205020AD5−6S
(See Note 4)
3 RIVET
SOLID
DOMED
CSK HD
− −
B0206002AG5−3
(See Note 5)
2 BOLT,
SHEAR,
FLUSH HD
− −
NOTES: 1. The part numbers for the items listed above are subject to change
without revision to this Service Bulletin. In case of discrepancy
between this list and any other list, the Illustrated Parts Data
Publication prevails and shall be used to determine the latest part
number.
2. Due to the lead−time for obtaining parts, operators are advised to
order the parts six (6) weeks in advance before scheduling the
incorporation of this Service Bulletin. Please contact Parts Services,
in Montreal, for delivery lead times and confirmation of prices.
3. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
4. Rivets are necessary for solution 1.
5. Fasteners are necessary for solution 2.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aviation does not pay
for these consumables.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 7 of 13

### Page 9

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER
Cleaning
Solvent
(DS−108)
(07−002) − As Necessary Code: A
Epoxy primer,
green
44GN072
(Base) /
44GN072CAT
(Catalyst)
(09−009)
(See Note 3)
BAMS 565−001 GR
B, CAT 2, TY 2 As Necessary Code: A
Sealant
Pro−Seal 870
B
(06−002)
(See Note 3)
MIL−PRF−81733
TYPE IV, CL 1, GR
A
As Necessary Code: A
Sealant
Pro−Seal 870
C
(06−001)
(See Note 3)
MIL−PRF−81733
TYPE II, CL 1, GR A As Necessary Code: A
Enamel coating
PG−21 series
(base) / PH−63
(hardener)
(09−143)
(See Note 3)
BAMS 565−002,
CLASS 20 OR 33 As Necessary Code: B
Adhesive,
Epoxy
Loctite EA 956
Aero Hysol EA 956 A/B As Necessary Code: C
Wiper Cloth (05−442)(See Note 3) − As Necessary Code: D
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
3. Refer to PART No.s listed in AMP
BD700−A−J51−31−00−00AAA−070A−A for details.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 8 of 13

### Page 10

SUPPLIERS ADDRESSES BY CODES
Code: A
PRC−Desoto International
5676 Timberlea Blvd.
Mississauga, Ontario
Canada, L4W 4M6
Tel.: (905) 629−7999
Fax.: (905) 629−7009
www.ppgaerospace.com
Code: B
Hentzen Coatings, Inc
6937 W mil Rd
Milwaukee
WI − 53218−1225
United States
www.hentzen.com
Code: C
Henkel Corporation Aerospace
2850 Willow Pass Road
P. O. Box 312
Bay Point, CA 94565 USA
Tel.: 925.458.8000
Fax: 925.458.8030
www.henkel−adhesives.com
Code: D
Commercially Available
D. Publications
None.
MODEL BD−700−2A12 (BD−700)
Basic Issue: Jul 21/2021 700−53−7547
Page 9 of 13

### Page 11

C
A
STR20L
FS833.00
STR6L
FS1016.66
STR19L
A
FWD
B
C
FS961.45
FS945.75
SB700−53−7547_001
FS961.45
FS945.75
STR19L
B0205020AD5−6S
(MISSING RIVETS)
G05362000−003
(AFT FUSELAGE
PANEL ASSEMBLY)
B
FS961.45
FS945.75
FWD
F
D
EG
H
MODEL BD−700−2A12 (BD−700)
Installation of Rivets and Fasteners on STR 19L between FS945.75 and FS961.45
Figure 1 (Sheet 1 of 4)
Basic Issue: Jul 21/2021 700−53−7547
Page 10 of 13

### Page 12

SB700−53−7547_002
K
FS961.45
FS945.75
STR19L
6.00 in
(152.40 mm)
FS945.75
FS961.45
STR19L
6.00 in
(152.40 mm)
FS945.75
FS961.45
STR19L
B0205020AD5−6S
(MISSING RIVETS)
G05362000
(AFT FUSELAGE
PANEL ASSEMBLY)
G05384000
(AFT FAIRING
ASSEMBLY)
FS961.45
FS945.75
STR19L
G05362000−003
(AFT FUSELAGE
PANEL ASSEMBLY)
D
F
E
G
J
B0205020AD5−6S
(RIVETS)
(QTY 3)
MODEL BD−700−2A12 (BD−700)
Installation of Rivets and Fasteners on STR 19L between FS945.75 and FS961.45
Figure 1 (Sheet 2 of 4)
Basic Issue: Jul 21/2021 700−53−7547
Page 11 of 13

### Page 13

SB700−53−7547_003
3.245 in
(82.42 mm)1.082 in
(27.48 mm) 1.082 in(27.48 mm) 0.35 in(8.89 mm)
INSTALLED
HI−LITE
INSTALLED
RIVET
INSTALLED
RIVET
G05362149−101
(STRINGER 19)
PILOT HOLE
G05362000
(AFT FUSELAGE
PANEL ASSEMBLY)
H
FWD
NOTES
1
2
Cut aft fairing 0.312 in (7.92 mm) corner radius maximum centered with pilot holes.
G05362000
(AFT FUSELAGE
PANEL ASSEMBLY)
G05384000
(AFT FAIRING
ASSEMBLY)
FAIRING
ATTACHMENT
HOLE
INSTALLED
HI−LITE
B0206002AG5−3
(BOLT) INSTALLED
RIVET
SOLUTION 2
J
The full maximum corner radius is 0.312 in (7.92 mm) for two places.
Ensure to achieve minimum edge distance (ED) = 0.80 in (20.32 mm) between edge of radius fairing
and centre of existing attaching fairing screw.
3
2
Cut perpendicular to EOP, two places.
3
L
0.312 in
(7.92 mm)
RADIUS
1
MODEL BD−700−2A12 (BD−700)
Installation of Rivets and Fasteners on STR 19L between FS945.75 and FS961.45
Figure 1 (Sheet 3 of 4)
Basic Issue: Jul 21/2021 700−53−7547
Page 12 of 13

### Page 14

INSTALLED
HI−LITE
INSTALLED
RIVET
INSTALLED
RIVET
G05362149−101
(STRINGER 19)
G05362000
(AFT FUSELAGE
PANEL ASSEMBLY)
B0203013−08
(NUT)
K
FWD
G05362000
(AFT FUSELAGE
PANEL ASSEMBLY)
G05384000
(AFT FAIRING
ASSEMBLY)
INSTALLED
HI−LITE
INSTALLED
RIVET
SOLUTION 2
L
NOTE
4 Fill aft fairing trimmed area with gap and aerodynamic sealant, smooth surfaces, touch−up
primer and topcoat.
SB700−53−7547_004
4
MODEL BD−700−2A12 (BD−700)
Installation of Rivets and Fasteners on STR 19L between FS945.75 and FS961.45
Figure 1 (Sheet 4 of 4)
Basic Issue: Jul 21/2021 700−53−7547
Page 13 of 13

### Page 15

700−53−7547 Basic Jul 21/2021
SPECIAL CHECK/MODIFICATION – AFT FUSELAGE SKIN AND ACCESS
PANELS – INSPECT FOR MISSING RIVETS AT AFT FUSELAGE
STRINGER 19
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 16

SERVICE BULLETIN INCORPORATION SHEET − "700−53−7547"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−53−7547 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
