# Bombardier Service Bulletin 700-71-6501

Copy: No revision named ("SB 700-71-6501 Basic"), 29 pages: PDF https://openairdocs.org/files/sha256/b8/01/b80175ad8432c545fabcf08a0b3d0fecd924198302e1462204a67feae812df08; text https://openairdocs.org/service-documents/bombardier/sb-700-71-6501/file/b80175ad8432.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0560; AD 2021-21-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 700-71-6501
- Page: https://openairdocs.org/service-documents/bombardier/sb-700-71-6501

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-21-04](https://openairdocs.org/ad/2021-21-04.md), effective Dec 8, 2021: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-700-71-6501/proposed.md).

## Text (29 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0560; AD 2021-21-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK – FRONT AND REAR ENGINE MOUNT ASSEMBLIES –
INSPECTION OF BUSHINGS ON THE ENGINE MOUNT SYSTEM
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 9861, 9872, 60001 to 60004, 60009, and 60016
MANPOWER: Refer to Paragraph 1.F.
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS NOYES
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 71−23, 71−24
POWERPLANT
Basic Issue: Dec 14/2020 700−71−6501
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK – FRONT AND REAR ENGINE MOUNT ASSEMBLIES –
INSPECTION OF BUSHINGS ON THE ENGINE MOUNT SYSTEM1.
PLANNING INFORMATION
NOTE: Before you do this Service Bulletin, examine all STC, STA or equivalent
action changes to make sure that this Service Bulletin can be completed.
A. Effectivity
BD−700−1A10 aircraft, Serial No. 9861, 9872, 60001 to 60004, 60009, and 60016.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Evidence:
There have been reports that bushings were missing from the forward engine
mount system.
2. Objective/Benefit:
This Service Bulletin instructs to inspect the forward and aft engine mount
system for missing bushings and to verify the proper installation of the sliding
bushings. Continued operation of engine with bushings missing will result in
redistribution of load/stress in the engine mount system and may lead to the
damage of mount components.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−700−1A10 (BD−700)
ATA 71−23, 71−24
POWERPLANT
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2020 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Dec 14/2020 700−71−6501
Page 1 of 26
This Service Bulletin is available at:

### Page 3

C. Description
This Service Bulletin gives instructions in PART A to:
− Inspect at the upper and lower side of front mount beam for proper installation of
sliding bushing, Part No. BRR15811.
This Service Bulletin gives instructions in PART B to:
− Inspect at the thrust strut front location for proper installation of sliding bushing,
Part No. BRR15808.
This Service Bulletin gives instructions in PART C to:
− Inspect at the thrust strut aircraft pylon interface for proper installation of sliding
bushing, Part No. BRR15823.
This Service Bulletin gives instructions in PART D to:
− Inspect at the front mount beam interface with the aircraft pylon upper and lower
installation for proper installation of sliding bushing, Part No. BRR15804.
This Service Bulletin gives instructions in PART E to:
− Inspect at the rear mount beam interface with the aircraft pylon upper and lower
installation for proper installation of sliding bushing, Part No. BRR15841.
D. Compliance
Recommended in less than 750 flight hours or 15 months, whichever comes first
from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 2 of 26

### Page 4

F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 700−00−6502.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin
10.5 man−hours are necessary to do this Service Bulletin.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 750 flight hours or 15 months,
whichever comes first, from its release date (Basic Issue).
G. Material − Cost and Availability
No kit or parts are necessary to do this Service Bulletin.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
20X−10−01 S4933959−501 Tag, Circuit Breaker (Red
Ring)
71X−13−02 G700−711302−1 Protective Mats − Lower
Engine Cowl
Commercially available − Feeler Gauge
Commercially available − Wrench, Torque 125 to
250 lbf in (14.13 to 28.24
Nm)
NOTES: 1. Refer to the Global 6500 Illustrated Tool and Equipment Manual
(ITEM) to make sure that you use the correct equipment
configuration.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 3 of 26

### Page 5

2. Refer to the Liability Statement in the ITEM for the G6500 for
acceptable GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive (Pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI), C−01793,
Rev. −−.
− Rolls Royce, Engine Maintenance Manual (EMM), Chapters 70 and 71.
− Global 6500 BD−700 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 71
and 78.
− Global 6500 BD−700 Illustrated Tool and Equipment Manual (ITEM), Chapters
20 and 71.
L. Other Publications Affected
None.
M. Equivalent Service Bulletins
− For the Global Express and Global Express XRS BD−700−1A10 aircraft, use
Service Bulletin 700−71−005.
− For the Global 5000 BD−700−1A11 aircraft, use Service
Bulletin 700−1A11−71−005.
− For the Global 5000 BD−700−1A11 Featuring Global Vision Flight Deck aircraft,
use Service Bulletin 700−71−5005.
− For the Global 6000 BD−700−1A10 aircraft, use Service Bulletin 700−71−6005.
− For the Global 5500 BD−700−1A11 aircraft, use Service Bulletin 700−71−5501.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 4 of 26

### Page 6

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the Global 6500
BD−700−1A10 Aircraft Maintenance Manual (AMM) unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are from the
Global 6500 BD−700−1A10 Aircraft Maintenance Manual (AMM),
Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to OUT or LOCKED. Refer to AMM 24−00−00−863−801:
For the left engine:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
APU APU START BATT
ENGINE L FADEC CH A BATT
ENGINE L FADEC CH B BATT
ENGINE L ENG IGN 1 BATT
ENGINE L ENG IGN 2 BATT
ENGINE L ENG FUEL HPSOV BATT
ENGINE L ENG START A BATT
ENGINE L ENG START B BATT
THRUST REVERSER L T/R CTL VALVE BATT
THRUST REVERSER L T/R UPPER LOCK BATT
THRUST REVERSER L T/R LOWER LOCK BATT
THRUST REVERSER L T/R TQA LOCK BATT
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 5 of 26

### Page 7

SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
HYD HYD PUMP 1B AC 3
For the right engine:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
APU APU START BATT
ENGINE R FADEC CH A BATT
ENGINE R FADEC CH B BATT
ENGINE R ENG IGN 1 BATT
ENGINE R ENG IGN 2 BATT
ENGINE R ENG FUEL HPSOV BATT
ENGINE R ENG START A BATT
ENGINE R ENG START B BATT
THRUST REVERSER R T/R CTL VALVE BATT
THRUST REVERSER R T/R UPPER LOCK BATT
THRUST REVERSER R T/R LOWER LOCK BATT
THRUST REVERSER R T/R TQA LOCK BATT
HYD HYD PUMP 2B AC 2
(3) Open and tag the circuit breakers that follow to make sure the heaters do not
come on:
For the left engine:
LOCATION CB NO. NAME ZONE
CCBP H7 PITOT 1 HT A 222
CCBP F5 PITOT 1 HT B 222
CCBP F6 PITOT 3 HT 222
CCBP F4 L AOA HEAT 222
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 6 of 26

### Page 8

LOCATION CB NO. NAME ZONE
CCBP F3 TAT HT 1 222
For the right engine:
LOCATION CB NO. NAME ZONE
CCBP B1 PITOT 2 HT 222
CCBP F10 STBY PITOT HT 222
CCBP H9 R AOA HEAT A 222
CCBP F8 R AOA HEAT B 222
CCBP F9 TAT HT 2 222
(4) Open and tag the circuit breakers that follow:
For the left engine:
LOCATION CB NO. NAME ZONE
DCPC A1 FIREX CH A 130
DCPC A2 FIREX CH B 130
DCPC A3 L ENG FUEL SOV 130
For the right engine:
LOCATION CB NO. NAME ZONE
DCPC A1 FIREX CH A 130
DCPC A2 FIREX CH B 130
DCPC A4 R ENG FUEL SOV 130
(5) Open the access door (311BB).
WARNING: MAKE SURE THAT YOU DO A DEACTIVATION OF THE THRUST
REVERSER BEFORE YOU DO WORK ON THE ENGINE. THE
THRUST REVERSER CAN ACCIDENTALLY OPERATE. THIS CAN
CAUSE INJURY TO PERSONS OR DAMAGE TO THE EQUIPMENT.
(6) Obey all the thrust reverser safety precautions. Refer to
AMM 78−30−00−910−801.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 7 of 26

### Page 9

(7) Do the deactivation of the thrust reverser (for maintenance). Refer to
EMM BR700NG−A−78−30−00−01AAA−560A−A.
(8) Obey all engine safety precautions. Refer to AMM 71−00−00−910−801.
WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE DURING
OR AFTER AN ENGINE OPERATION. THE ENGINE PARTS STAY
HOT FOR APPROXIMATELY THREE HOURS AFTER THE ENGINE
STOPS. THIS CAN CAUSE INJURY TO PERSONS.
WARNING: BE CAREFUL IF YOU MUST DO WORK ON HOT COMPONENTS.
USE APPROVED GLOVES AND PROTECTIVE CLOTHING. IF YOU
DO NOT DO THIS, YOU CAN CAUSE INJURY TO PERSONS.
(9) Remove the pylon panel for thrust strut and front mount 412AB/422AB. Refer
to AMM 54−52−01−000−801.
(10) Remove the pylon panel for rear mount 412BB/422BB. Refer to
AMM 54−52−01−000−801.
(11) Remove the firebox lower access panel 432BT/442BT. Refer to
CMM 71−14−51 or 71−14−52.
(12) Open the lower cowl 432AB/442AB. Refer to AMM 71−10−00−010−801.
NOTE: Lower cowl need not to be removed but must be opened.
(13) Remove the upper cowl 432AT/442AT. Refer to AMM 71−10−00−010−801.
(14) Remove the firebox lid 432CT/442CT. Refer to CMM 71−14−51 or 71−14−52.
B. PART A — Inspection of Sliding Bushing (BRR15811) at the Upper and Lower
Side of Front Mount Beam
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the gap check at upper side of front mount beam as follows, refer to
Figure 1, Detail C and D:
(a) Using a feeler gauge, measure Gap A between front mount beam pin, Part
No. BRR15812 and the shouldered bushing installed on the front mount
beam (standard installation), or gap between the shouldered bushing
installed on the front mount beam and the washer Part No. BRR15810
(alternative installation), must be between 0.004 and 0.055 in (0.10 and
1.40 mm).
Record the results in Appendix (Table 1) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 8 of 26

### Page 10

(b) For Pre SB BR700−71−101976 aircraft, inspect the nut, Part No. AS54364
and bolt, Part No. AS53914 at the upper side of front mount beam for
missing or physical damage.
NOTE: If missing or physical damage found, fill out an SRPSA and send
it by E−mail at:
SRPSA@aero.bombardier.com
(c) Make sure that the bolt must not be free to turn with finger pressure.
NOTE: If bolt can be turned with finger pressure, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
(2) Do the gap check at lower side of front mount beam as follows, refer to
Figure 1, Detail C and D:
(a) Using a feeler gauge, measure Gap B between front mount beam pin, Part
No. BRR15812 and the shouldered bushing installed on the front mount
beam (standard installation), or gap between the shouldered bushing
installed on the front mount beam and the washer Part No. BRR15810
(alternative installation), must be between 0.004 and 0.055 in (0.10 and
1.40 mm).
Record the results in Appendix (Table 1) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
(b) For Pre SB BR700−71−101976 aircraft, inspect the nut, Part No. AS54364
and bolt, Part No. AS53914 at the lower side of front mount beam for
missing or physical damage.
NOTE: If missing or physical damage found, fill out an SRPSA and send
it by E−mail at:
SRPSA@aero.bombardier.com
(c) Make sure that the bolt must not be free to turn with finger pressure.
NOTE: If bolt can be turned with finger pressure, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
C. PART B – Inspection of Sliding Bushing (BRR15808) at the Thrust Strut Front
Location
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 9 of 26

### Page 11

(1) Do the gap check at the thrust strut front location as follows, refer to Figure 1,
Detail E and F:
(a) Using a feeler gauge, measure Gap C between the front mount beam pin,
Part No. BRR15809 and the shouldered bushing installed on the front
mount beam, must be between 0.008 and 0.050 in (0.20 and 1.30 mm).
Record the results in Appendix (Table 2) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
(b) For Pre SB BR700−71−101976 aircraft, inspect the nut, Part No. AS54364
and bolt, Part No. AS53912 at the thrust strut front location for missing or
physical damage.
NOTE: If missing or physical damage found, fill out an SRPSA and send
it by E−mail at:
SRPSA@aero.bombardier.com
(c) Make sure that the bolt must not be free to turn with finger pressure.
NOTE: If bolt can be turned with finger pressure, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
D. PART C — Inspection of Sliding Bushing (BRR15823) at the Thrust Strut
Aircraft Pylon Interface
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the gap check at the thrust strut aircraft pylon interface as follows, refer to
Figure 1, Detail E and G:
(a) Using a feeler gauge, measure the Gap D between the thrust strut pin,
Part No. BRR15824 and the shouldered bushing installed on the thrust
strut, must be between 0.008 and 0.055 in (0.20 and 1.40 mm).
Record the results in Appendix (Table 3) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 10 of 26

### Page 12

(b) For Pre SB BR700−71−101976 aircraft, inspect the nut, Part No. AS54364
and bolt, Part No. AS53912 at the thrust strut aircraft pylon interface for
missing or physical damage.
NOTE: If missing or physical damage found, fill out an SRPSA and send
it by E−mail at:
SRPSA@aero.bombardier.com
(c) Make sure that the bolt must not be free to turn with finger pressure.
NOTE: If bolt can be turned with finger pressure, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
E. PART D — Inspection of Sliding Bushing (BRR15804) at the Front Mount
Beam Interface with the Aircraft Pylon Upper and Lower Installation
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the gap check at the front mount beam Interface with the aircraft pylon
upper installation as follows, refer to Figure 1, Detail C and H:
(a) Using a feeler gauge, measure Gap E between the front mount beam pin,
Part No. BRR15805 and the shouldered bushing installed on the front
mount beam (standard installation) or gap between the washer Part No.
BRR15807 and the shouldered bushing installed on the front mount beam
(alternative installation), must be in between 0.008 and 0.048 in (0.20 and
1.20 mm).
Record the results in Appendix (Table 4) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
(2) Do the gap check at the front mount beam Interface with the aircraft pylon
lower installation as follows, refer to Figure 1, Detail C and H:
(a) Using a feeler gauge, measure Gap F between the front mount beam pin,
Part No. BRR15805 and the shouldered bushing installed on the front
mount beam (standard installation) or gap between the washer Part No.
BRR15807 and the shouldered bushing installed on the front mount beam
(alternative installation), must be in between 0.008 and 0.048 in (0.20 and
1.20 mm).
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 11 of 26

### Page 13

Record the results in Appendix (Table 4) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
F. PART E — Inspection of Sliding Bushing (BRR15841) at the Rear Mount
Beam Interface with the Aircraft Pylon Upper and Lower Installation
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the gap check at the rear mount beam Interface with the aircraft pylon
upper installation as follows, refer to Figure 1, Detail K and L:
(a) Using a feeler gauge, measure Gap G between the rear mount beam pin,
Part No. BRR15840 and the shouldered bushing installed on the rear
mount beam (standard installation) or gap between the washer Part No.
BRR15842 and the shouldered bushing installed on the rear mount beam
(alternative installation), must be between 0.004 and 0.071 in (0.10 and
1.80 mm).
Record the results in Appendix (Table 5) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
(2) Do the gap check at the rear mount beam Interface with the aircraft pylon lower
installation as follows, refer to Figure 1, Detail K and L:
(a) Using a feeler gauge, measure Gap H between the rear mount beam pin,
Part No. BRR15840 and the shouldered bushing installed on the rear
mount beam (standard installation) or gap between the washer Part No.
BRR15842 and the shouldered bushing installed on the rear mount beam
(alternative installation), must be between 0.004 and 0.071 in (0.10 and
1.80 mm).
Record the results in Appendix (Table 5) and send it to TS by E−mail at
tech.services.global.series@aero.bombardier.com.
NOTE: If the gap is not within acceptable limits, fill out an SRPSA and
send it by E−mail at:
SRPSA@aero.bombardier.com
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 12 of 26

### Page 14

G. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Install the firebox lid 432CT/442CT. Refer to CMM 71−14−51 or 71−14−52.
(3) Install the upper cowl 432AT/442AT. Refer to AMM 71−10−00−410−801.
(4) Close the lower cowl 432AB/442AB. Refer to AMM 71−10−00−410−801.
(5) Install the firebox lower access panel 432BT/442BT. Refer to CMM 71−14−51
or 71−14−52.
(6) Install the pylon panel for rear mount 412BB/422BB. Refer to
AMM 54−52−01−400−801.
(7) Install the pylon panel for thrust strut and front mount 412AB/422AB. Refer to
AMM 54−52−01−400−801.
(8) Do the activation of the thrust reverser (for maintenance). Refer to
EMM BR700NG−A−78−30−00−01AAA−760A−A.
(9) Close the access door (311BB).
(10) In the flight compartment, on the EMS CDU, set the circuit breakers that follow
to IN. Refer to AMM 24−00−00−863−802.
For the left engine:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
APU APU START BATT
ENGINE L FADEC CH A BATT
ENGINE L FADEC CH B BATT
ENGINE L ENG IGN 1 BATT
ENGINE L ENG IGN 2 BATT
ENGINE L ENG FUEL HPSOV BATT
ENGINE L ENG START A BATT
ENGINE L ENG START B BATT
THRUST REVERSER L T/R CTL VALVE BATT
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 13 of 26

### Page 15

SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
THRUST REVERSER L T/R UPPER LOCK BATT
THRUST REVERSER L T/R LOWER LOCK BATT
THRUST REVERSER L T/R TQA LOCK BATT
HYD HYD PUMP 1B AC 3
For the right engine:
SYSTEM NAME CIRCUIT BREAKER
NAME
BUS NAME
APU APU START BATT
ENGINE R FADEC CH A BATT
ENGINE R FADEC CH B BATT
ENGINE R ENG IGN 1 BATT
ENGINE R ENG IGN 2 BATT
ENGINE R ENG FUEL HPSOV BATT
ENGINE R ENG START A BATT
ENGINE R ENG START B BATT
THRUST REVERSER R T/R CTL VALVE BATT
THRUST REVERSER R T/R UPPER LOCK BATT
THRUST REVERSER R T/R LOWER LOCK BATT
THRUST REVERSER R T/R TQA LOCK BATT
HYD HYD PUMP 2B AC 2
(11) Remove the tags and close the circuit breakers that follow:
For the left engine:
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 14 of 26

### Page 16

LOCATION CB NO. NAME ZONE
DCPC A1 FIREX CH A 130
DCPC A2 FIREX CH B 130
DCPC A3 L ENG FUEL SOV 130
For the right engine:
LOCATION CB NO. NAME ZONE
DCPC A1 FIREX CH A 130
DCPC A2 FIREX CH B 130
DCPC A4 R ENG FUEL SOV 130
(12) Remove the tags and close the circuit breakers that follow:
For the left engine:
LOCATION CB NO. NAME ZONE
CCBP H7 PITOT 1 HT A 222
CCBP F5 PITOT 1 HT B 222
CCBP F6 PITOT 3 HT 222
CCBP F4 L AOA HEAT 222
CCBP F3 TAT HT 1 222
For the right engine:
LOCATION CB NO. NAME ZONE
CCBP B1 PITOT 2 HT 222
CCBP F10 STBY PITOT HT 222
CCBP H9 R AOA HEAT A 222
CCBP F8 R AOA HEAT B 222
CCBP F9 TAT HT 2 222
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 15 of 26

### Page 17

H. Recording
When this Service Bulletin is completed, make an entry in the aircraft log, send the
attached Incorporation Notice and the results Appendix Record Table to
Bombardier Business Aircraft Customer Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
No parts required.
C. Material
No consumables are required.
D. Publications
No publications required.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 16 of 26

### Page 18

APPENDIX — RECORD TABLE
SPECIAL CHECK – FRONT AND REAR ENGINE MOUNT ASSEMBLIES –
INSPECTION OF BUSHINGS ON THE ENGINE MOUNT SYSTEM
INSTRUCTIONS
Fill out the tables below. Refer to the instructions given in the Service Bulletin, and send this
Appendix to TS by E−mail at:
tech.services.global.series@aero.bombardier.com
TABLE 1
Record the gap between the shouldered bushing installed on the front mount beam
and the front mount beam pin (BRR15812), or the washer (BRR15810), as applicable.
*If the gap is not 0.004 and 0.055 in (0.10 and 1.40 mm), send an SRPSA to
SRPSA@aero.bombardier.com.
Location in* or mm* Comments
L/H Front
Mount
Beam
Upper side
(Gap A)
Lower side
(Gap B)
R/H Front
Mount
Beam
Upper side
(Gap A)
Lower side
(Gap B)
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 17 of 26

### Page 19

TABLE 2
Record the gap between the front mount beam pin (BRR15809) and the shouldered
bushing installed on the front mount beam.
*If the gap is not between 0.008 and 0.050 in (0.20 and 1.30 mm), send an SRPSA to
SRPSA@aero.bombardier.com.
Location in* or mm* Comments
L/H Thrust Strut Front
(Gap C)
R/H Thrust Strut Front
(Gap C)
TABLE 3
Record the gap between the thrust strut pin (BRR15824) and the shouldered bushing
installed on the thrust strut.
*If the gap is not between 0.008 and 0.055 in (0.20 and 1.40 mm), send an SRPSA to
SRPSA@aero.bombardier.com.
Location in* or mm* Comments
L/H Thrust Strut
Aircraft Pylon
Interface (Gap D)
R/H Thrust Strut
Aircraft Pylon
Interface (Gap D)
TABLE 4
Record the gap between the shouldered bushing installed on the front mount beam
and the front mount beam pin (BRR15805), or the washer (BRR15807), as applicable.
*If the gap is not between 0.008 and 0.048 in (0.20 and 1.20 mm), send an SRPSA to
SRPSA@aero.bombardier.com.
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 18 of 26

### Page 20

TABLE 4
Location in* or mm* Comments
L/H Front
Mount
Beam
interface
with the
Aircraft
Pylon
Upper
Installation
(Gap E)
Lower
Installation
(Gap F)
R/H Front
Mount
Beam
interface
with the
Aircraft
Pylon
Upper
Installation
(Gap E)
Lower
Installation
(Gap F)
TABLE 5
Record the gap between the shouldered bushing installed on the rear mount beam
and the rear mount beam pin (BRR15840), or the washer (BRR15842), as applicable.
*If the gap is not between 0.004 and 0.071 in (0.10 and 1.80 mm), send an SRPSA to
SRPSA@aero.bombardier.com.
Location in* or mm* Comments
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 19 of 26

### Page 21

TABLE 5
L/H Rear
Mount
Beam
interface
with the
Aircraft
Pylon
Upper
Installation
(Gap G)
Lower
Installation
(Gap H)
R/H Rear
Mount
Beam
interface
with the
Aircraft
Pylon
Upper
Installation
(Gap G)
Lower
Installation
(Gap H)
MODEL BD−700−1A10 (BD−700)
Basic Issue: Dec 14/2020 700−71−6501
Page 20 of 26

### Page 22

SB700−71−6501_001
FRONT MOUNT/ THRUST STRUT ASSEMBLY
2
3
(LH SHOWN, RH SIMILAR)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 1 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 21 of 26

### Page 23

Pre SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE FORWARD MOUNT BEAM
Post SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE FORWARD MOUNT BEAM
(ALTERNATIVE INSTALLATION)
AS54364
(NUT)
BRR15810
(WASHER)
FRONT MOUNT BEAM
BRR15813
(LINK ASSY)
BRR15812
(PIN)
AS53914
(BOLT)
BRR24405
(LINK ASSY)
BRR24405
(LINK ASSY)
KH77506
(BOLT)
SP9064
(COTTER PIN)
BRR15812
(PIN)
U781291
(NUT)
FRONT MOUNT BEAM
FRONT MOUNT BEAM
BRR15810
(WASHER)
BRR15810
(WASHER) BRR15812(PIN)
GAP A/ GAP B GAP A/ GAP B
GAP A/ GAP B
SB700−71−6501_002
(STANDARD INSTALLATION)
GAP
A
B
Range of the gap to be measured
Between 0.004 in. and 0.055 in. (0,10 mm and 1,40 mm)
Between 0.004 in. and 0.055 in. (0,10 mm and 1,40 mm)
U781291
(NUT)
SP9064
(COTTER PIN)
BRR15811
(SLIDING BUSHING)
BRR15811
(SLIDING BUSHING)
BRR15811
(SLIDING BUSHING)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 2 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 22 of 26

### Page 24

Pre SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE FORWARD MOUNT BEAM
TO THRUST STRUT
SB700−71−6501_003
BRR15809
(PIN)
FRONT MOUNT
BEAM
BRR15810
(WASHER)AS54364
(NUT)
THRUST STRUT
GAP C
Post SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE FORWARD MOUNT BEAM
TO THRUST STRUT
BRR15810
(WASHER)
U781291
(NUT)
SP90C4
(COTTER PIN)
THRUST STRUT
KH77506
(BOLT) BRR15809
(PIN)
FRONT MOUNT
BEAM
GAP C
AS53912
(BOLT)
GAP
C
Range of the gap to be measured
Between 0.008 in. and 0.050 in. (0,20 mm and 1,30 mm)
BRR15808
(SLIDING BUSHING)
BRR15808
(SLIDING BUSHING)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 3 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 23 of 26

### Page 25

Pre SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE THRUST STRUT TO AIRCRAFT PYLON
SB700−71−6501_004
AIRCRAFT PYLON
THRUST STRUT
AS54364
(NUT)
BRR15824
(PIN) BRR15810(WASHER)
AS53912
(BOLT)
GAP D
Post SB−BR700−71−101976 
STANDARD TYPICAL INTERFACE THRUST STRUT TO AIRCRAFT PYLON
GAP D
U781291
(NUT)
BRR15824
(PIN)
THRUST STRUT
BRR15810
(WASHER)
KH77506
(BOLT)
AIRCRAFT PYLON
SP90C4
(COTTER PIN)
GAP
D
Range of the gap to be measured
Between 0.008 in. and 0.055 in. (0,20 mm and 1,40 mm)
BRR15823
(SLIDING BUSHING)
BRR15823
(SLIDING BUSHING)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 4 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 24 of 26

### Page 26

REAR MOUNT ASSEMBLY
SB700−71−6501_005
TYPICAL INTERFACE FRONT MOUNT BEAM
SP90G6
(COTTER PIN)
U755248
(NUT)
SP90G6
(COTTER PIN)
BRR15807
(WASHER)
BRR15805
(PIN)
BRR15806
(BOLT)
BRR15805
(PIN)
BRR15806
(BOLT)
BRR15804
(SLIDING BUSHING)
U755248
(NUT)
FRONT MOUNT BEAM
GAP E/ GAP F
FRONT MOUNT BEAM
GAP E/ GAP F
GAP
E
F
Range of the gap to be measured
Between 0.008 in. and 0.048 in. (0,20 mm and 1,20 mm)
Between 0.008 in. and 0.048 in. (0,20 mm and 1,20 mm)
(ALTERNATIVE INSTALLATION)(STANDARD INSTALLATION)
BRR15804
(SLIDING BUSHING)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 5 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 25 of 26

### Page 27

TYPICAL INTERFACE REAR MOUNT BEAM − AIRCRAFT PYLON
GAP GGAP G
BRR15840
(PIN)
BRR16268
(BOLT)
BRR15842
(WASHER)
U755248
(NUT)
SP90G6
(COTTER PIN)
GAP H
U755248
(NUT)
SP90G6
(COTTER PIN)
BRR15842
(WASHER)
BRR16268
(BOLT)
BRR15840
(PIN)
SP90G6
(COTTER PIN)
U755248
(NUT)
BRR15842
(WASHER)
BRR16268
(BOLT)
BRR15840
(PIN)
REAR MOUNT
BEAM
REAR MOUNT
BEAM
BRR15840
(PIN)
BRR16268
(BOLT)
GAP H
SP90G6
(COTTER PIN)
U755248
(NUT)
BRR15842
(WASHER)
GAP
G
H
Range of the gap to be measured
Between 0.004 in. and 0.071 in. (0,10 mm and 1,80 mm)
Between 0.004 in. and 0.071 in. (0,10 mm and 1,80 mm)
SB700−71−6501_006
(ALTERNATIVE INSTALLATION)(STANDARD INSTALLATION)
BRR15841
(SLIDING BUSHING)
BRR15841
(SLIDING BUSHING)
BRR15841
(SLIDING BUSHING)
BRR15841
(SLIDING BUSHING)
MODEL BD−700−1A10 (BD−700)
Inspection of Sliding Bushings
Figure 1 (Sheet 6 of 6)
Basic Issue: Dec 14/2020 700−71−6501
Page 26 of 26

### Page 28

700−71−6501 Basic Dec 14/2020
SPECIAL CHECK – FRONT AND REAR ENGINE MOUNT ASSEMBLIES –
INSPECTION OF BUSHINGS ON THE ENGINE MOUNT SYSTEM
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 29

SERVICE BULLETIN INCORPORATION SHEET − "700−71−6501"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
700−71−6501 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
