# Bombardier Service Bulletin 8-27-111

Copy: No revision named ("U.S. DOT/FAA - SB 8-27-111"), 18 pages: PDF https://openairdocs.org/files/sha256/30/a6/30a62a85ad8910ddd6ba7af3a62b097ce9daec69109a9c8a1f85c43ee8829b98; text https://openairdocs.org/service-documents/bombardier/sb-8-27-111/file/30a62a85ad89.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1311; AD 2013-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 8-27-111
- Page: https://openairdocs.org/service-documents/bombardier/sb-8-27-111

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-22-04](https://openairdocs.org/ad/2013-22-04.md), effective Dec 5, 2013: No revision named

## Text (18 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1311; AD 2013-22-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

D
S . B . 8 --- 2 7 --- 1 1 1
Page 1 of 16
15 Jun 2011
JR
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2730 NUMBER: 8- - -27- - -111
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGES OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Flight Controls - - - Addition of Bushing in Brake Pedal Bell Crank - - -
Rudder Control - - - ModSum 8Q113007
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 102, 103, 106, 201, 202, 301, 311,
314 and 315 Serial Numbers 003 thru 672.
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None

### Page 2

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 2 of 16
15 Jun 2011
JR
B. Reason
Problem: During maintenance, an operator found that the LH & RH pilot brake pedal
bellcrank had exhibited excessive wear in the tie rod attachment clevis
hole.
Solution: This service bulletin provides instructions to add a steel bushing to the rod
attachment clevis hole, or replace with new bellcrank containing steel
bushing.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- - - aircraft is put into standard configuration for maintenance
- - - aircraft electrical power is removed
- - - the nose landing gear lock is engaged
- - - the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- - - pilot & co- - -pilot brake pedal bellcranks are inspected
- - - pilot & co- - -pilots bellcranks are either re- - -worked to install steel bushing or
replaced
- - - close out.
D. Compliance
Bombardier Inc. highly recommend that ModSum 8Q113007 be incorporated at
the earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
O r g a n i z a t i o n N o : D A O # 9 3 --- Q --- 0 2 .
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).

### Page 3

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 3 of 16
15 Jun 2011
JR
F. M a n p o w e r
The following is the man- - -hours required to complete the ACCOMPLISHMENT
INSTRUCTIONS in this service bulletin. The breakdown of man - - -hours is shown in
the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.50
Procedure (Inspection) 1.00
Procedure (Bushing Installation) 4.00
Procedure (Bellcrank Replacement) 16.00
T e s t/R T S 2.00
Close- - -Out 0.50
For any on- - -site labor assistance, please speak with a Fleet Services representative for
a quote. The Fleet Services group can be contacted via the Q Series T echnical Help
Desk by telephone at 416- - -375- - -4000 or email at: thd.qseries@aero.bombardier.com
G. Material - - - Price and Availability
ModKit 8MK4453- - -001 is available through the Customer Accounts Service T eam
at Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial number(s) to:
Bombardier Aerospace
Customer Accounts Services T eam (Mail Stop N11- - -32)
123 Garratt Blvd.
To r o n t o
Ontario
Canada M3K- - -1Y5
Facsimile: (416) 375- - -3060
T elephone: (416) 375- - -3920
Kit Number Description
8MK4453- - -001 Retrofit Kit - - -Bellcrank Assembly - - - Pedal Assembly
Rudder Controls

### Page 4

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 4 of 16
15 Jun 2011
JR
H. T ooling - - - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1- - -8- - -4 and....................
P S M 1 --- 8 2 --- 4
P S M 1 --- 8 3 --- 4
Modifications Manual PSM 1- - -813- - -12...............................
L. References
The initial issue of this service bulletin was prepared to the engineering drawings
and related data that follows:
DRAWING SHEET REV
8MK4453 1 A
8Z6930 1 D
ModSum 8Q113007 Rev. ‘C’
PCA 6753 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive Pending
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4453- - -001
(2) Detailed Kit Content:

### Page 5

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 5 of 16
15 Jun 2011
JR
Quantity Per Kit
--- 0 0 1
Part Number Description Remarks
4 MS24665- - -163 Cotter Pin
4 NAS6603CD13 Bolt
8 82710297- - -101 Bushing
1 8Z6930 Retrofit Bellcrank Assembly Drawing
1 8MK4453 Retrofit Kit Drawing
(3) In addition to the above parts, the following material is required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in either
Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter 51.
Part Number Qty. Per Aircraft Description Remarks
MS20995C32 as required Lockwire
F19 as required P r i m e r --- Ty p e I I MIL- - -PRF- - -23377
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None
D. Existing Parts Accountability
None

### Page 6

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 6 of 16
15 Jun 2011
JR
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS (refer to AMM Chapter 24).
(2) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Remove access panels 121AL and 122AR from the nose fuselage. Refer to
Maintenance Manual Chapter 06- - -40- - -10 (S100/300) and 06- - -40- - -00 (S200).
B. Procedure
(1) Insert rig pins A, B, C and D in the LH and RH rudder output levers and rudder
forward quadrants. Refer to Maintenance Manual Chapter 27- - -20- - -00.
(2) Disconnect control rod assembly 82710795- - -001 or 82710024- - -003 (four
places). Retain hardware, discard cotter pin. Refer to Figure 1.
Part A - - - Inspection
(1) Determine length of clevis holes on each bellcrank. If length is less than or equal
to 0.218 inches from edge to edge (see Figure 6 for reference) then crack check
using Liquid Penetrant Inspection (LPI). Refer to ASTM E1417.
(2) If crack is found, replace with new bellcrank (refer to Part C. Bellcrank
Replacement), otherwise rework the bellcrank (refer to Part B Bushing
Installation (In- - -Situ)).
(3) If length is greater than 0.218 inches replace with new bellcrank (refer to Part C
Bellcrank Replacement).
Part B - - - Bushing Installation (In- - - Situ)
(1) Disconnect rod assembly 82710274- - -001 (two places) from bellcranks on pilots
side. Retain hardware, discard cotter pin. Refer to Figure 1.
(2) Disconnect cable assembly 82700570- - -001/- - -003 from bellcranks on co- - -pilots
side. Retain hardware, discard cotter pin. Refer to Figure 2.
NOTE: In order to remove the clevis pins from the co- - -pilots bellcranks the cable
tension must be released by temporarily moving the brake control
assembly levers on the pilots side forward.

### Page 7

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 7 of 16
15 Jun 2011
JR
(3) Open the hole on original center in bellcrank assembly as shown in section
A- - -A/B- - -B of Figures 4 & 5 using a reamer 0.250 inches diameter with a 0.187
inches pilot.
NOTE: Reamer should not be longer than 2 inches and to be used with an angle
drill.
NOTE: Alternatively, bushing installation ma y be conducted outside the aircraft.
Follow the applicable instructions in Part C to remove the bellcrank from
the aircraft and to install the reworked bellcrank into aircraft.
NOTE: If original hole is damaged, bellcrank may be re- - -used only if hole
enlargement (to the size shown in section A- - -A/B- - -B) is sufficient to repair
the damage and edge distance as shown in Figure 4 can be maintained.
Otherwise bellcrank requires replacement. Replace with
82710813- - -003/- - -004 and 82710814- - -003/- - -004. For aircraft without
ModSum 8Q101218 installed also use 82710813- - -003/- - -004 and
82710814- - -003/- - -004.
(4) Deburr holes. Make sure edge distance is 0.310± 0.030 inches. Refer to Figures
4&5 .
(5) Refer to Figures 4 & 5 wet install bushings 82710297- - -101 into bellcrank
assembly using F19 primer. Refer to AMM 20- - -12- - -04 for applicable instruction.
(6) Re- - -identify bellcrank assembly 82710813- - -001/- - -002 as 8Z6930- - -051/- - -053
and 82710814- - -001/- - -002 as 8Z6930- - -055/- - -057. Refer to Maintenance Manual
C h a p t e r 2 0 --- 1 5 --- 0 4 .
(7) Re- - -identify bellcrank assembly 82710022- - -001/- - -002 as 8Z6930- - -059/- - -061
and 82710029- - -001/- - -002 as 8Z6930- - -063/- - -065 for aircraft without ModSum
8Q101218 installed. Refer to Maintenance Manual Chapter 20- - -15- - -04.
(8) Connect control rod assembly 82710795- - -001 or 82710024- - -003 (four places) to
reworked bellcranks using kept hardware and new bolt NAS6603CD13 and new
cotter pin MS24665- - -163. Refer to Figure 1. If bolt doesn’t fit, ream bushing to
0.190/0.192 inches diameter.
(9) Connect rod assembly 82710274- - -001 (two places) to reworked bellcranks on
pilots side using kept hardware and new cotter pin MS24665- - -153. Refer to
Figure 1.
(10) Connect cable assembly 82700570- - -001/- - -003 to reworked bellcranks on
co- - -pilots side using kept hardware and new cotter pin MS24665- - -153. Refer to
Figure 2.
Part C - - - Bellcrank Replacement
(1) On the flight compartment floor, remove and retain all the screws securing the
rudder pedal cover to the floor. Leave cover in place.

### Page 8

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 8 of 16
15 Jun 2011
JR
(2) Disconnect rod assembly 82710274- - -001 (two places) from bellcranks on pilots
side. Retain hardware, discard cotter pin. Refer to Figure 1.
(3) Disconnect cable assembly 82700570- - -001/- - -003 from bellcranks on co- - -pilots
side. Retain hardware, discard cotter pin. Refer to Figure 2.
(4) Disconnect rudder force sensor 9000934- - -1 or rod assembly 82710028- - -003
(four places) from the rudder control pedal assembly. Retain hardware, discard
cotter pin. Refer to Figure 1.
(5) Remove microswitch support bracket 82710812. Retain hardware and shim if
present. Be careful not to damage microswitches. Refer to Figure 3.
(6) Index mark rudder control pivot assembly mounting flange and fitting on both
sides.
(7) Remove pivot assembly fitting 82710021- - -101. Retain hardware. Refer to Figure 2.
(8) Remove and retain hardware from the pivot assembly mounting flange. Refer to
Figure 2.
(9) While holding the pivot tube assembly gently twist the assembly and slightly
move it aft until it clears the rudder pedal assembly mounting brackets.
(10) Rotate the pivot tube mounting flange in a clockwise and anti- - -clockwise
direction while moving towards the inboard until tube as moved enough to
remove the bellcrank.
NOTE: As you move the pivot tube inboard be sure to support the teflon spacers
and bushings.
(11) Remove affected bellcrank and replace with a new bellcrank containing steel
bushing.
(12) Rotate the pivot tube mounting flange in a clockwise and anti- - -clockwise
direction while moving towards the outboard until its fully through.
(13) While holding the pivot tube assembly gently twist the assembly and slightly
move it forward until it positions itself on the rudder pedal assembly mounting
brackets.
(14) Install pivot assembly fitting 82710021- - -101 using kept hardware. Refer to
Figure 2.
(15) Secure pivot assembly mounting flange to the rudder pedal assembly mounting
brackets using kept hardware.
(16) Install microswitch support bracket 82710812 and shim 82710602- - -953, if
originally present, using kept hardware. Refer to Figure 3.
(17) Connect rudder force sensor 9000934- - -1 or rod assembly 82710028- - -003 (four
places) to the rudder control pedal assembly using kept hardware and new
cotter pin MS24665- - -153. Refer to Figures 1 & 2.

### Page 9

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 9 of 16
15 Jun 2011
JR
(18) Connect cable assembly 82700570- - -001/- - -003 to the bellcranks on co- - -pilots
side using kept hardware and new cotter pin MS24665- - -163. Refer to Figure 2.
(19) Connect rod assembly 82710274- - -001 (two places) to the bellcranks on pilots
side using kept hardware and new cotter pin MS24665- - -163. Refer to Figure 1.
(20) On the flight compartment floor secure the rudder pedal cover to the floor using
kept hardware.
(21) Connect control rod assembly 82710795- - -001 or 82710024- - -003 (four places) to
bellcranks using kept hardware and new bolt NAS6603CD13 and new cotter pin
MS24665- - -163. Refer to Figure 1.
(22) Identify the installation as 8Z6930- - -001 & 8Z6930- - -002 and 8Z6930- - -003 &
8Z6930- - -004 for aircraft without ModSum 8Q101218 installed.
Refer to Maintenance Manual Chapter 20- - -15- - -04.
C. Close Out
(1) Do the Return to Service Procedure as follows:
(d) Remove rig pins A, B, C and D.
(e) Move the pedal adjustment mechanism fully forward and operate the
rudder pedals forward and aft.
Check for full and free movement of the rudder pedals.
For aircraft equipped with force sensors 9000934- - -1, check for clearance
between the sensor harness and the adjacent components.
Inspect for clearance as follows:
(f) Minimum clearance of 0.12 inches (3.05 mm) between the harness and
surrounding components.
(g) Minimum clearance of 0.375 inches (9.53 mm) between the force sensor
and surrounding components except the fitting assembly and the aft rod
end bearing of the force sensor.
(h) Move the pedal adjustment mechanism fully aft and operate the rudder
pedals forward and aft.
Check for full and free movement of the rudder pedals.
For aircraft equipped with force sensors 9000934- - -1, check for clearance
between the sensor harness and the adjacent components.
Inspect for clearance as follows:
1 Minimum clearance of 0.12 inches (3.05 mm) between the harness
and surrounding components.
2 Minimum clearance of 0.375 inches (9.53 mm) between the force
sensor and surrounding components except the fitting assembly and
the aft rod end bearing of the force sensor.

### Page 10

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 10 of 16
15 Jun 2011
JR
(i) Apply full pilot brake travel to each pedal for a minimum of 25 cycles. Make
sure the system has full and free movement.
(j) Apply full co- - -pilot brake travel to each pedal for a minimum of 25 cycles.
Make sure the system has full and free movement.
NOTE: Make sure the brake linkages go back to their initial position after each
brake application. The co- - -pilot brake lever will touch the structural stop.
(k) Check and if necessary, adjust the brake position switch. Refer to
Maintenance Manual T ask 27- - -20- - -03- - -400- - -802 (Series 200) or Chapter
27- - -20- - -03 Section 4 (Series 300).
(2) Remove all tools and equipment from the work area.
(3) Install access panels 121AL and 122AR to the nose fuselage. Refer to
Maintenance Manual Chapter 06- - -40- - -10 (Series 100/300) or 06- - -40- - -00 (Series
200).
(4) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 11

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 11 of 16
15 Jun 2011
JR
Pilots Pedals
Figure 1
BOLT NAS1801- - -3D10
WASHER AN960D10L
LOCK WIRE MS20995C32
8Z6930- - -061 (Pre MS)
8Z6930- - -053
BOLT NAS1103- - -3
NUT MS21042- - -3
WASHER AN960D10L
CONTINUED ON FIGURE 2
8Z6930- - -059
(Pre MS)
8Z6930- - -051
BOLT NAS1303- - -7D
NUT MS14144L3
WASHER AN960D10L
COTTER PIN
MS24665- - -163
BOLT NAS1103- - -3
NUT MS21042- - -3
WASHER AN960D10L
RUDDER PEDAL ASSEMBL Y (TYP)
MOUNTING BRACKET
ROD ASSEMBL Y
82710274- - -001
RUDDER FORCE SENSOR
9000934- - -1 (TYP)
OR
ROD ASSEMBL Y
82710028- - -003 (TYP)
CONTROL ROD ASSEMBL Y (TYP)
82710795- - -001 or 82710024- - -003
(TYP)

### Page 12

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 12 of 16
15 Jun 2011
JR
C o --- P i l o t s P e d a l s
Figure 2
FROM FIGURE 1
BOLT NAS1801- - -3D10
WASHER AN960D10L
LOCK WIRE MS20995C32
8Z6930- - -063 (Pre MS)
8Z6930- - -055
BOLT NAS1303- - -3
NUT MS21042- - -3
WASHER AN960D10L
8Z6930- - -065
(Pre MS)
8Z6930- - -057
PIN MS20392- - -2C11
COTTER PIN MS24665- - -153
WASHER AN960D10L
BOLT NAS1303- - -3
NUT MS21042- - -3
WASHER AN960D10L
CABLE ASSEMBL Y
82700570- - -001
CABLE ASSEMBL Y
82700570- - -003
PIVOT ASSEMBL Y
MOUNTING FLANGE (TYP)
PIVOT ASSEMBL Y
FITTING (TYP)
82710021- - -101

### Page 13

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 13 of 16
15 Jun 2011
JR
Detail C and D
Figure 3
BOL T
NAS6603CD13
NUT
MS14144L3
WASHER
AN960D10L
COTTER PIN
MS24665- - -163
NOTE: Tighten nut to ensure positive
clamp- - -up of bearing inner race.
8Z6930- - -059 (Pre MS)
8Z6930- - -051
8Z6930- - -063 (Pre MS)
8Z6930- - -055
8Z6930- - -061 (Pre MS)
8Z6930- - -053
8Z6930- - -065 (Pre MS)
8Z6930- - -057
MICROSWITCH
SUPPORT BRACKET
82710812
ROD ASSEMBL Y
P/N 82710795- - -001 or P/N 82710024- - -003

### Page 14

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 14 of 16
15 Jun 2011
JR
Bushing Installation
Figure 4
BUSHING
82710297- - -101
(one on each lug)
(Pre MS)
(Pre MS)
0.310 ± 0.030 2 PLCS
EDGE DISTANCE

### Page 15

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 15 of 16
15 Jun 2011
JR
Bushing Installation
Figure 5
(Pre MS)
(Pre MS)
BUSHING
82710297- - -101
(one on each lug)
2
0.310 ± 0.030 2 PLCS
EDGE DISTANCE

### Page 16

S E R V I C E B U L L E T I N 8 --- 2 7 --- 1 1 1
S . B . 8 --- 2 7 --- 1 1 1
Page 16 of 16
15 Jun 2011
JR
Edge to edge length reference
Figure 6
1

### Page 17

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 18

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
