# Bombardier Service Bulletin 8-32-156

Copy: No revision named ("U.S. DOT/FAA - Service Information - 3"), 10 pages: PDF https://openairdocs.org/files/sha256/f5/8d/f58dd9f11a8a2cf1b3a8a920329a7b813aa8985ba9ff4ab6d2a4cb2751e97ba2; text https://openairdocs.org/service-documents/bombardier/sb-8-32-156/file/f58dd9f11a8a.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-0422; AD 2012-15-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 8-32-156
- Page: https://openairdocs.org/service-documents/bombardier/sb-8-32-156

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2012-15-16](https://openairdocs.org/ad/2012-15-16.md), effective Sep 12, 2012: No revision named

## Text (10 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-0422; AD 2012-15-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

D
S . B . 8 --- 3 2 --- 1 5 6
Page 1 of 8
26 Feb 2010
JR
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 3200 NUMBER: 8- - -32- - -156
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGES OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Landing Gear - - - Nose Landing Gear - - - Replacement of Pushrod
Assembly to Substitute T4 with a T6 - - - ModSum 8Q101335
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 201, 202, 301, 311, 314 and 315
Serial Numbers 552 thru 588.
Spares Affected:
The following is a list of spares affected by this change. Review spares and
procurement systems to determine the existence of any listed parts. See
Paragraph 2.D., Existing Parts Accountability, for disposition.
Part Number Description Remarks
83232012- - -001 Pushrod - - - Nose
Landing Gear
Manufactured after
September 2000

### Page 2

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 2 of 8
26 Feb 2010
JR
B. Reason
Some pushrods may have been incorrectly manufactured with tubes having the
wrong heat treat condition using 6061- - -T4 instead of 6061- - -T6.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- - - the affected pushrod is removed, destroyed and discarded
- - - a new pushrod is installed. A functional test of the nose landing gear doors is
performed
D. Compliance
Bombardier Aerospace highly recommends that this modification be incorporated
at the operators earliest opportunity, unless otherwise directed by their
Airworthiness Authority.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
O r g a n i z a t i o n N o : D A O # 9 3 --- Q --- 0 2 .
F. M a n p o w e r
It will take an estimated 2 man- - -hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.00
Procedure 2.00
T e s t/R T S 0.00
Close- - -Out 0.00

### Page 3

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 3 of 8
26 Feb 2010
JR
G. Material - - - Price and Availability
ModKit 8MK4279- - -001 is available through the Customer Accounts Service T eam
at Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial number(s) to:
Bombardier Aerospace
Customer Accounts Services T eam (Mail Stop N11- - -32)
123 Garratt Blvd.
To r o n t o
Ontario
Canada M3K- - -1Y5
Facsimile: (416) 375- - -3060
T elephone : (416) 375- - -3920
Kit Number Description
8MK4279- - -001 Retrofit Kit- - -Pushrod Replacement,
Nose Landing Gear
H. Weight and Balance
None
I. Electrical Load Data
Not affected
J. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1- - -82- - -4 and....................
P S M 1 --- 8 3 --- 4
Modifications Manual PSM 1- - -813- - -12...............................

### Page 4

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 4 of 8
26 Feb 2010
JR
K. References
The initial issue of this service bulletin was prepared to the engineering drawings
and related data that follows:
DRAWING SHEET REV
8MK4279 1 A
ModSum 8Q101335 Rev. ‘B’
PCA 4522 Revision - - - - - - (for internal reference only)
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4279- - -001
(2) Detailed Kit Content:
Quantity Per Kit
--- 0 0 1
Part Number Description Remarks
1 8MK4279 Kit Drawing
2 MS24665- - -153 Cotter Pin
4 AN960- - -516 Washer
1 83232012- - -951 P u s h r o d --- N L G
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None

### Page 5

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 5 of 8
26 Feb 2010
JR
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non- - -indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
83232012- - -001 Pushrod 1 B DIS 83232012- - -951 S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate
on part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
(1) Either pull and clip circuit breakers required to isolate affected circuits or placard
and select aircraft electrical power to OFF . Obey all relevant WARNINGS and
CAUTIONS detailed in Maintenance Manual PSM 1- - -82- - -2 or PSM 1- - -83- - -2.
(2) Lock the nose landing gear doors. Refer to Maintenance Manual Chapter PSM
1 --- 8 2 --- 2 T A S K 3 2 --- 0 0 --- 0 0 --- 8 4 0 --- 8 0 1 o r P S M 1 --- 8 3 --- 2 C h a p t e r 3 2 --- 2 0 --- 2 1 .

### Page 6

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 6 of 8
26 Feb 2010
JR
WARNING: MAKE SURE THAT THE LOCKPINS ARE INSTALLED IN THE MAIN
LANDING GEAR. MAKE SURE THE NOSE GEAR LOCK IS ENGAGED.
IF THIS IS NOT DONE, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE
TO THE EQUIPMENT .
WARNING: BE SURE THAT THE HYDRAULIC PRESSURE IS OFF , AND THAT
THERE IS NO PRESSURE IN THE HYDRAULIC SYSTEM. IF YOU DO
NOT DO THIS YOU CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
B. Procedure
(1) Remove and discard pushrod 83232012- - -001 from the nose landing gear
forward door as follows: (Refer to Maintenance Manual PSM 1- - -82- - -2 TASK
3 2 --- 2 2 --- 1 1 --- 0 3 0 --- 8 0 1 o r P S M 1 --- 8 3 --- 2 C h a p t e r 3 2 --- 2 0 --- 2 1 f o r a c c e s s l o c a t i o n
and to drawing 8MK4279)
(a) Disconnect one end of the pushrod from the bellcrank by removing one
cotter pin MS24665- - -153, one nut MS14145L5, two washers AN960- - -516,
one bolt NAS1105- - -12D and one bushing NAS75- - -5- - -006. Keep all
hardware except for washers and cotter pin.
(b) Disconnect the other end of the pushrod from the door attachment bracket
by removing one cotter pin MS24665- - -153, one nut MS14145L5, two
washers AN960- - -516 and one bolt NAS1105- - -20D. Keep all hardware
except for washers and cotter pin.
(2) After removing each defective Pushrod (P/N 83232012- - -001) cut each part into
two pieces in a way that will render them UNSERVICEABLE, wire lock the two
pieces together. T ag the parts and dispose them as instructed by your Local
Airworthiness Authority.
(3) Install and rig new pushrod 83232012- - -951 to the nose landing gear forward
door as follows: (Refer to Maintenance Manual PSM 1- - -82- - -2 TASK
3 2 --- 2 2 --- 1 1 --- 8 3 0 --- 8 0 1 o r P S M 1 --- 8 3 --- 2 C h a p t e r 3 2 --- 2 0 --- 2 1 f o r r i g g i n g
instructions and to drawing 8MK4279)
(a) Connect one end of the pushrod to the door attachment bracket using one
nut MS14145L5, two new washers AN960- - -516 and one bolt
NAS1105- - -20D. T orque nut 40 to 80 inch pounds and lock with new cotter
pin MS24665- - -153.

### Page 7

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 7 of 8
26 Feb 2010
JR
(b) Connect the other end of the pushrod to the bellcrank by using one nut
MS14145L5, two new washers AN960- - -516, one bolt NAS1105- - -12D and
one bushing NAS75- - -5- - -006. T orque nut 50 to 70 inch pounds and lock
with new cotter pin MS24665- - -153.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) Perform a functional test of the Nose Landing Gear Doors per Maintenance
M a n u a l P S M 1 --- 8 2 --- 2 T A S K 3 2 --- 3 0 --- 0 0 --- 7 2 0 --- 8 0 1 o r P S M 1 --- 8 3 --- 2 C h a p t e r
32- - -20- - -21.
(3) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 8

S E R V I C E B U L L E T I N 8 --- 3 2 --- 1 5 6
S . B . 8 --- 3 2 --- 1 5 6
Page 8 of 8
26 Feb 2010
JR
This Page Intentionally Blank
1

### Page 9

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : Partner Data Co- - -Ordinator (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 3534 Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 10

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
