# Bombardier Service Bulletin 84-26-11

Copy: Revision A ("U.S. DOT/FAA - SB-84-26-11-RA"), 20 pages: PDF https://openairdocs.org/files/sha256/4f/95/4f95f9124b60965d194629d615fc1ac08eb526a4090151dfe66f44dd9c4e7f1e; text https://openairdocs.org/service-documents/bombardier/sb-84-26-11/file/4f95f9124b60.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1155; AD 2013-09-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-26-11
- Latest revision known: 84-26-11, Revision A, dated January 25, 2012 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-26-11

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-09-04](https://openairdocs.org/ad/2013-09-04.md), effective Aug 2, 2013: Revision A

## Text (20 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1155; AD 2013-09-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘A’ 25 Jan 2012
DHC-8 (DASH 8)
SERVICE BULLETIN 84-26-11
Fire Protection - Aft Nacelle Bracket Modification to Prevent Fire
Detection Wire Chafing - ModSum 4-113717
This page transmits Revision ‘A’ of Service Bulletin 84-26-11, pages 1 thru
16, dated: 25 Jan 2012.
This service bulletin is re-issued in its entirety for the reasons that follow:
- the Material - Price and Availability section is revised to show correct kit
number
- the References section is revised to convey the latest revision of the service
bulletin and engineering documentation
- the MATERIAL INFORMATION section is revised to show correct kit
number
The Compliance in the previous issue of this service bulletin is not affected
by this revision. No additional rework to the aircraft is introduced by this
revision.
Remove previous issue of Service Bulletin 84-26-11 and replace with
attached.
Previous issues of Service Bulletin 84-26-11:
Initial issue - Pages 1 thru 16 dated 19 Dec 2011

### Page 2

(No text on this page.)

### Page 3

D
S.B. 84-26-11
Page 1 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2611 NUMBER: 84-26-11
SUBJECT: Fire Protection - Aft Nacelle Bracket Modification to Prevent Fire
Detection Wire Chafing - ModSum 4-113717
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003, 4004, 4006, 4008 thru 4382.
Production: ModSum 4-113717 will be installed before delivery on
applicable DHC-8 Aircraft at Serial Number 4383 thru 4429.
Production: Equivalent Production ModSum 4-170047 will be installed
before delivery on applicable DHC-8 Aircraft at Serial Number
4430 and subsequent.
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None

### Page 4

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 2 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
B. Reason
Problem: It has been discovered that chafing between the main landing gear yoke
assembly and the fire detection wire can occur.
Solution: This service bulletin provides instructions to install a new bracket and
secure the fire detection wire in the aft nacelle.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- aircraft electrical power is removed
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- safety stands are placed around the main landing gear
- main landing gear (MLG) yoke and the fire detection wires are inspected for
chafing and damages
- existing bracket supporting fire detection wire is removed
- new brackets are installed
- close out.
D. Compliance
Bombardier Inc. recommends incorpora tion of ModSum 4-113717 at the earliest
opportunity unless otherwise directed by the operator’s airworthiness authority.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).

### Page 5

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 3 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
F. Manpower
It will take an estimated 3.00 man-hours to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 0.25
Procedure 2.00
Test / RTS 0.50
Close-Out 0.25
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com
G. Material - Price and Availability
ModKit 8MK4581-003 is available through the Customer Accounts Service Team at
Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial number(s) to:
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920
Kit Number Description
8MK4581-003 Mod Kit, Nacelle-Structures
Provisions-Fire Detection Sys
H. Tooling - Price and Availability
None

### Page 6

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 4 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
L. References
Revision ‘A’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4581 1 A
8Z9351 1 C
ModSum 4Q113717 Rev. ‘H’
ModSum 4-113717 Rev. ‘H’
Service Letter DH8-400-SL-32-030
PCA 43636 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive pending
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4581-003
(2) Detailed Kit Content:
Quantity Per Kit
-003
Part Number Description Remarks
12 B0205016AD4-3S Rivet
2 82624229-104 Bracket
4 B0205016AD4-4S Rivet
4 208236 Clamp, Hinged
4 324351 Grommet
2 82624229-103 Bracket

### Page 7

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 5 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
(1) Placard and select all aircraft electrical power to OFF. Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK’S 24-00-00-861-802 and
24-00-00-910-801).
(2) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set up the work platforms or ladders as required to gain access to the LH & RH
nacelle inboard and outboard panels. Ma ke sure the work platforms or ladders
are electrically grounded.
B. Procedure
(1) Do a detailed visual inspection of the fire detector wire. If there is any damage
noted on detector wire at location shown in Figure 7, discard the detector and
replace with new detector.
(2) Do a detailed visual inspection of the MLG yoke in the location shown in Figure
7. If chafing on MLG yoke with limitation as shown in Figure 8 is found, do the
necessary repair per Figure 9. If limitation of chafing as shown in Figure 8
Section A-A is exceeded, contact Q Series Help Desk
(thd.qseries@aero.bombardier.com) for further instructions.
(3) Carefully remove fire detection wire from existing bracket supporting the fire
detection wire on the LH and RH outboard and inboard nacelle panels. Refer to
Figures 1, 2 & 4.
(4) On the LH nacelle outboard panel and RH nacelle inboard panel, locate bracket
82624211 as shown in Figure 3, remove two existing rivets and install bracket
82624229-103 to same hole location using rivets B0205016AD4-4S.

### Page 8

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 6 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
(5) On the LH nacelle inboard panel and RH nacelle outboard panel, install bracket
82624229-104 using rivets B0205016AD4-3S as per dimensions shown in Figure
5.
(6) Install new hinged clamp 208236 to new brackets 82624229-103 &
82624229-104 using rivets B0205016AD4-3S. Refer to Figures 3 & 5.
(7) Install new grommet 324351 to fire detection wire. Refer to Figure 3 & 5.
(8) Carefully install fire detection wire to new bracket assembly. Refer to Figure 3 &
5.
NOTE: Make sure fire detection wire routing maintains a minimum bend radius of
R1.00 inches.
(9) Do an operational test of the nacelle fire detection system. Refer to Maintenance
Manual Task 26-11-00-710-801.
(10) Do an operational test of the landing gear primary extension and retraction
system to make sure clearance is maintained between the gear and detection
wire. Refer to Maintenance Manual Task 32-31-00-710-801.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 9

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 7 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Work Location
Figure 1
FIRE DETECTION SYSTEM
LH NACELLE
FIRE DETECTION SYSTEM
RH NACELLE

### Page 10

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 8 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Panel
Figure 2

### Page 11

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 9 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Panel
Figure 3
RIVET
B0205016AD4-3S
RIVET
B0205016AD4-4S
GROMMET
324351
BRACKET
82624229-103
CLAMP, HINGED
208236

### Page 12

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 10 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Panel
Figure 4

### Page 13

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 11 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Panel
Figure 5
A L LD I M E N S I O N SA R EG I V E NI NI N C H E S
RIVET
B0205016AD4-3S
RIVET
B0205016AD4-3S
GROMMET
324351
BRACKET
82624229-104
CLAMP, HINGED
208236
0.490
0.620
0.620
1.26

### Page 14

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 12 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Panel
Figure 6
CLAMP, HINGED
208236
GROMMET
324351
BRACKET
82624229-103
A L LD I M E N S I O N SA R EG I V E NI NI N C H E S

### Page 15

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 13 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
Nacelle Fire Detection Wire Contact Locations on MLG Yoke
Figure 7
FIRE DETECTION WIRE
INSPECTION AREA
FIRE DETECTION WIRE
INSPECTION AREA
YOKE
INSPECTION AREA
YOKE
INSPECTION AREA
View looking aft within nacelle with MLG extended

### Page 16 (OCR)

SERVICE BULLETIN 84-26-11
Typical tour locations, inboard/outboard yoke legs, port and starboard nacelles
* Up
„Outb'd
Fwd
Location of damage
9.0" / 10.0"
Measured from the
centerline of the lug to the
centre of the damage.
Length of chamfer must be:
Minimum: 20 X the maximum depth,
Maximum: 3.50"
Smoothly chamfer edge of the
Yoke to remove all damage.
Note: Damage and repair shown
on the fwd outb'd edge. Damage
and repair may also be located
on the aft outb'd, fwd inb'd and
View Looking on LH MLG Yoke  aft inb'd corners.
Smoothly chamfer edge Yoke to
remove all damage.
Outb'd
0.170" max.  * Fwd
0.170" max.
Figure 8
S.B. 84-26-11
Page 14 of 16
JR

### Page 17 (OCR)

SERVICE BULLETIN 84-26-11
General notes:
1. Blend and polish to remove damage as shown below, to the limits as specified in
Figure 8. Blend the minimum amount to remove all damage.
Blend out all damage as shown.
Blend the minimum amount to remove all damage.
20x min. - 3.50" max.
× = Depth of Blendout
2. All blended surfaces are to be smooth and free of nicks. Maintain surface finish equal
to or better than the original surface finish.
3. After blending away all the damage inspect the entire repair area using
fluorescent penetrant dye per ASTM E1417, Type 1, Sensitivity Level 3, Defects
onto to exceed MIL-STD-1907 Grade "A" Limits (or equivalent method).
4. Mask as required and locally flap peen reworked area per MIL-R-81841 at Almen
Intensity 0.008A - 0.012A, and 200% coverage.
5. Solvent clean rework area per CMM 32-11-04 requirements.
6. All bare metal is to be finished with alodine and epoxy primer.
7. Apply alodine in accordance with the instructions of the MIL-C-5541, Class 1A
requirements.
8. Apply epoxy prime in accordance with the instructions of MIL-PRF-23377.
Application per MIL-F-18264.
9. Finish external surface of the repair area with impact resistant topcoat in
accordance with the instructions of MIL-PRF-85285, Colour Gray NO 16473.
Application per MIL-F-18264.
10. Rubber stamp SB 84-26-11 on the Yoke Assembly adjacent to the rework area and
adjacent to the assembly part number. Apply a layer of clear coat lacquer over the
stamping.
11. Record the part number, serial number, TSN, and CSN of the Yoke Assy and forward
to Goodrich Engineering.
Figure 9
19 Dec 2011  S.B. 84-26-11
Revision 'A' 25 Jan 2012  Page 15 of 16
JR

### Page 18

SERVICE BULLETIN 84-26-11
S.B. 84-26-11
Page 16 of 16
19 Dec 2011
Revision ‘A’ 25 Jan 2012
JR
This Page Intentionally Blank
2

### Page 19

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 20

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
