# Bombardier Service Bulletin 84-26-12

Copy: Revision B ("Service Bulletin 84-26-12B"), 16 pages: PDF https://openairdocs.org/files/sha256/c3/7a/c37ad1c1381420afd6cd4c60b6278dd35a76985bc387bf80c1ceab87c55fa1bb; text https://openairdocs.org/service-documents/bombardier/sb-84-26-12/file/c37ad1c13814.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1003; AD 2013-16-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-26-12
- Latest revision known: 84-26-12, Revision B, dated October 12, 2012 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-26-12

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2013-16-25](https://openairdocs.org/ad/2013-16-25.md), effective Oct 4, 2013: Revisions A and B

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-26-12/proposed.md).

## Text (16 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-1003; AD 2013-16-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘B’ 12 Oct 2012
DHC-8 (DASH 8)
SERVICE BULLETIN 84-26-12
Fire Protection - Fire Detection - Replacement of Fire/Overheat Detector
P/N 10-1096 or 10-1096-01 or 10-1096-02 (Post SB 84-26-10A) with
10-1096-02 - Propeller Electronic Control - ModSum 4-113732
This page transmits Revision ‘B’ of Service Bulletin 84-26-12, pages 1 thru
12 dated: 12 Oct 2012.
This service bulletin is re-issued in its entirety for the reasons that follow:
-- the Effectivity section is revised to add aircraft serial numbers 4392 thru
4399 and Production cut-in at serial number 4400.
-- the References section is revised to convey the latest revision of the service
bulletin and engineering documentation
The Compliance recommendation in the previous issue of this service
bulletin is not affected by this revision. No further rework to the aircraft is
introduced by this revision.
Remove the previous issue of this Service Bulletin and replace with
attached.
Previous issues of Service Bulletin 84-26-12:
Initial issue - Pages 1 thru 12 dated 12 Oct 2011
Revision ‘A’ - Pages 1 thru 12 dated 13 Dec 2011

### Page 2

(No text on this page.)

### Page 3

D
S.B. 84-26-12
Page 1 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2621 NUMBER: 84-26-12
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fire Protection - Fire Detection - Replacement of Fire/Overheat
Detector P/N 10-1096 or 10-1096-01 or 10-1096-02 (Post SB
84-26-10A) with 10-1096-02 - Propeller Electronic Control - ModSum
4-113732
1. PLANNING INFORMATION
NOTE: This service bulletin supercedes Service Bulletin 84-26-10.
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4001 thru
4399.
Production: ModSum 4-113732 will be installed before delivery on
applicable DHC-8 Aircraft at Serial Number 4400 and
subsequent.
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.

### Page 4

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 2 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
Spares Affected:
Part Number Description
10-1096 or 10-1096-01 or
10-1096-02 (post SB 84-26-10A,
with s/n that has all numeric char-
acters)
Fire/Overheat Detector
B. Reason
Kidde Aerospace and Defense has modifi ed the Fire/Overheat Detector (APD -
Advance Pneumatic Detector) internal desig n to eliminate false fire indication after
fire has been extinguished.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- aircraft electrical power is removed
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- existing Fire/Overheat Detector P/N 10-1096 or 10-1096-01 or 10-1096-02 (post
SB 84-26-10A, with s/n that has all numeric characters) on both Propeller
Electronic Control is replaced with P/N 1096-02 that has serial number of three
alpha characters followed by four numeric characters
- an operational test of the nacelle fire detection system is done
- close out.
D. Compliance
Bombardier Inc. recommends incorpora tion of ModSum 4-113732 at the earliest
opportunity unless otherwise directed by the operator’s airworthiness authority.
Transport Canada Airworthiness Directive Pending.
E. Approval
The technical content of this service bulletin has been approved under the

### Page 5

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 3 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
F. Manpower
It will take an estimated 3.5 man-hours to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 0.50
Procedure 2.00
Test / RTS 0.50
Close-Out 0.50
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com
G. Material - Price and Availability
The part detailed in Paragraph 2.A. may be obtained from any Bombardier
Aerospace Regional Aircraft authorized parts source. The price and availability will
be quoted at the time of order.
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920
H. Tooling - Price and Availability
None
I. Weight and Balance
None

### Page 6

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 4 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
J. Electrical Load Data
Not affected
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
L. References
Revision ‘B’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
ModSum 4-113732 Rev. ‘B’
ModSum 4K113732 Rev. ‘B’
PCA 42588 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive Pending
Kidde Aerospace Service Bulletin 10-1096-26-487 Rev 2 Dec 1/11
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
Quantity
Per Aircraft
Part Number Description Remarks
2 10-1096-02 Fire/Overheat Detector
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None

### Page 7

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 5 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non-indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
10-1096
or
10-1096-01
or
10-1096-02
(post SB 84-26-10A,
with s/n that has all
numeric characters)
Fire/Overheat
Detector
2 B SAL 10-1096-02 with
s/n of three alpha
and four numeric
characters
S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate on
part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.

### Page 8

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 6 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
(1) Placard and select all aircraft electrical power to OFF. Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK’S 24-00-00-861-802 and
24-00-00-910-801).
(2) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set up work platforms or ladders as required to gain access to left and right
engines. Make sure the work platforms or ladders are electrically grounded.
B. Procedure
(1) Remove existing left and right propeller electronic control advance pneumatic
detector (Fire/Overheat Detector P/N 10-1096 or 10-1096-01 or 10-1096-02 with
s/n that has all numeric characters). Re fer to Figure 1, Maintenance Manual Task
26-11-03-000-801 and enclosed Kidde Aerospace Service Bulletin
10-1096-26-487.
(2) Install on the left and right propeller electronic control advance pneumatic
detector (Fire/Overheat Detector P/N 10-1096-02 that has serial number of three
alpha characters followed by four numeric characters). Refer to Maintenance
Manual Task 26-11-03-400-801 and enclosed Kidde Aerospace Service Bulletin
10-1096-26-487.
NOTE: Refer to enclosed Figures 1 & 2 for serial number reference.
(3) Do the operational test of the Nacelle Fire Detection System. Refer to
Maintenance Manual Task 26-11-00-710-801.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 9

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 7 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
Figure 1
Serial Number Identification of Existing Detector (for reference only)

### Page 10

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 8 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
Figure 2
Serial Number Identification of New Detector (for reference only)

### Page 11 (OCR)

SERVICE BULLETIN 84-26-12
Kidde Aerospace & Defense
SERVICE BULLETIN
FIRE PROTECTION - FIRE DETECTION - REPLACEMENT OF
FIRE/OVERHEAT DETECTORS, P/NS 10-1096, 10-1096-01, 10-1096-02
Transmittal Sheet
This page transmits Revision 2 of the Service Bulletin dated Dec 1/11.
The purpose of the revision is instruct operators to return all removed detectors to Kidde Aerospace &
Revision 1 dated Sep 26/11 clarified the numeric configuration of the detector serial numbers.
INFORMATION SUBJECT TO EXPORT CONTROL LAWS
Export Control Castical Number 9SE991
F-50724  10-1096-26-487
Aug 12/11
Rev. 2 Dec 1/11
12 Oct 2011  S.B. 84-26-12
Revision 'B' 12 Oct 2012  Page 9 of 12
JR

### Page 12 (OCR)

SERVICE BULLETIN 84-26-12
Kidde Aerospace & Defense
SERVICE BULLETIN
FIRE PROTECTION - FIRE DETECTION - REPLACEMENT OF
FIRE/OVERHEAT DETECTORS, P/NS 10-1096, 10-1096-01, 10-1096-02
1. PLANNING INFORMATION
A. Effectivity
(1) Fire/overheat detector P/N 10-1096, 10-1096-01 or 10-1096-02, serial num-
bers beginning with "11" followed by four unique numbers, used on Bombar-
dier Aerospace Dash 8 400 aircraft.
B. Reason
(1) The detector may not reset after exposure to the flame test of TSO-C11e.
C. Description
(1) This service bulletin provides the instructions to remove fire/overheat detector
10-1096, 10-1096-01 or 10-1096-02 and install new replacement fire/over-
heat detector, P/N 10-1096-02. The replacement detector serial numbers will
consist of three alpha characters followed by four numeric characters.
D. Approval
(1) This service bulletin has been reviewed and accepted by Bombardier Aero-
space.
E. Manpower
(1) Refer to Bombardier Cover Service Bulletin 84-26-12.
F. Material - Cost and Availability
(1) Refer to Bombardier Cover Service Bulletin 84-26-12.
G. Tooling
(1) No special tools are required.
H. Weight and Balance
(1) Not Affected.
I. Electrical Load Data
(1) Not Affected.
J. References
(1) Bombardier Aerospace Aircraft Maintenance Manual (AMM) PSM 1-84-2.
Aug 12/11  10-1096-26-487
Rev. 2 Dec 1/11  Page 1 of 2
12 Oct 2011  S.B. 84-26-12
Revision 'B' 12 Oct 2012  Page 10 of 12
JR

### Page 13 (OCR)

SERVICE BULLETIN 84-26-12
Kidde Aerospace & Defense
SERVICE BULLETIN
FIRE PROTECTION - FIRE DETECTION - REPLACEMENT OF
FIRE/OVERHEAT DETECTORS, P/NS 10-1096, 10-1096-01, 10-1096-02
(2) Bombardier Aerospace Aircraft Illustrated Parts Catalog (AIPC) PSM 1-84-4.
(3) 4K113713, 84-26-08 and 4K113699, 84-26-09.
K. Other Publications Affected
(1) Kidde Aerospace & Defense Abbreviated Component Maintenance Manual
(ACMM) 26-10-03.
2. ACCOMPLISHMENT INSTRUCTIONS
A. Remove the fire/overheat detector 10-1096, 10-1096-01 or 10-1096-02 with serial
number that has all numeric characters as specified in Bombardier Aerospace
Aircraft Maintenance Manual PSM 1-84-2.
B. Install replacement fire/overheat detector P/N 10-1096-02 that has serial number
of three alpha characters followed by four numeric charactersas specified in
Bombardier Aerospace Aircraft Maintenance Manual PSM 1-84-2.
C. Return the removed detector to:
Kidde Aerospace & Defense
4200 Airport Dr NW
Building B
Wilson, NC 27896 USA
3.  MATERIAL INFORMATION
A. No additional materials are necessary to accomplish this Service Bulletin.
Aug 12/11  10-1096-26-487
Rev. 2 Dec 1/11  Page 2 of 2
12 Oct 2011  S.B. 84-26-12
Revision 'B' 12 Oct 2012  Page 11 of 12
JR

### Page 14

SERVICE BULLETIN 84-26-12
S.B. 84-26-12
Page 12 of 12
12 Oct 2011
Revision ‘B’ 12 Oct 2012
JR
This Page Intentionally Blank
5

### Page 15

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 16

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
