# Bombardier Service Bulletin 84-26-19

Copy: No revision named ("SB-84-26-19A"), 22 pages: PDF https://openairdocs.org/files/sha256/05/94/0594518243986bd16a97c44ddfaced8adba51778594a1ec06157fd74c4f0192b; text https://openairdocs.org/service-documents/bombardier/sb-84-26-19/file/059451824398.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0702; AD 2020-02-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-26-19
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-26-19

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-02-10](https://openairdocs.org/ad/2020-02-10.md), effective Mar 12, 2020: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-26-19/proposed.md).

## Text (22 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2019-0702; AD 2020-02-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T x L t r S B 8 4 --- 2 6 --- 1 9
Page 1 of 2
Revision ‘A’ 11 Feb 2019
BM
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
Fire Protection - - - FIre Detection System - - - Nacelles and Auxiliary Power Unit
(APU) - - - Advanced Pneumatic Detectors (APD) - - - Special Inspection, T esting
and Rectification
This page transmits Revision ‘A’ of Service Bulletin 84- - -26- - -19, pages 1 thru 18,
dated 11 Feb 2019.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- s e c t i o nA. Effectivity is revised from 4001, 4003 and subsequent to 4001, 4003
thru 4588.
--- s e c t i o nL. References is revised to convey the latest revision of the service bulletin
and existing engineering documentation.
The Compliance in the previous issue of this service bulletin is not affected by this
revision. No additional rework to the aircraft is introduced by this revision.
Remove the initial issue of Service Bulletin 84- - -26- - -19 and replace with attached.
Previous issue(s) of Service Bulletin 84- - -26- - -19:
Initial issue - - - Pages 1 thru 18 dated 24 Oct 2018

### Page 2

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
T x L t r S B 8 4 --- 2 6 --- 1 9
Page 2 of 2
Revision ‘A’ 11 Feb 2019
BM
This Page Intentionally Blank

### Page 3

D
S . B . 8 4 --- 2 6 --- 1 9
Page 1 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2610 NUMBER: 84- - -26- - -19
BOMBARDIER AEROSPACE CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Fire Protection - - - Fire Detection System - - - Nacelles and Auxiliary
Power Unit (APU) - - - Advanced Pneumatic Detectors (APD) - - - Special
Inspection, T esting and Rectification
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4588 with Advanced Pneumatic Detector (APD) part
numbers and applicable serial numbers listed in T able 1
installed.
Part Number Serial number
10- - -1096 All Serial Numbers
10- - -1096- - -01 All Serial Numbers
10- - -1096- - -02 Serial numbers before AEM9907
10- - -1097 All Serial Numbers

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 2 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
Part Number Serial number
10- - -1097- - -01 All Serial Numbers
10- - -1097- - -02 Serial Numbers before 17- - -0005
10- - -1098 All Serial Numbers
10- - -1098- - -01 Serial Numbers before 17- - -0110
10- - -1099 All Serial Numbers
10- - -1099- - -01 Serial Numbers before 17- - -0009
Ta b l e 1
Spares Affected:
Refer to enclosed Kiddie service bulletin 10- - -1096- - -26- - -511.
B. Reason
Problem: Supplier Kidde (UTAS), through an investigation, had disclosed to
Bombardier Aerospace that conditions may exist in their Advanced
Pneumatic Detector (APD) system where the sensor alarm may not be
correctly set during an overheat or fire event.
T o date, there have been no confirmed in- - -service occurrences of APD
failing to indicate as a consequence of this issue.
It has been discovered that an issue can develop where contamination can
cause the alarm switch from making electrical contact. This could delay the
unit in responding to an alarm condition or engine fire.
Cause: Through detailed investigation, K idde had discovered that contamination
in the form of black dots was found on the contact pin of APD pressure
switch. This contamination acts as an electrical insulator between the
contact pin and the diaphragm which results in an open electrical circuit
even when the switch closes to indicate a fire or overheat.
Solution: In order to determine that the alarm switch will make proper contact during
a fire event, the sensor tube of the detector must be heated above the
discrete alarm set point. This will result in alarm switch closure which can
then be checked with a digital multi- - -meter (DMM) or Aircraft Indication
Systems.

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 3 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
This service bulletin and the merged Kidde Aerospace & Defense Service
Bulletin 10- - -1096- - -26- - -511 provide the instructions to do the on- - -wing
test to determine the defective APD and replace as necessary.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
Part A gives the job set- - -up instructions.
- - - aircraft electrical power is removed
- - - the nose landing gear lock is engaged
- - - the main landing gear lock pins are installed thru each main gear and main gear door
mechanism
- - - access panels on the left and right nacelles and APU doors are opened
- - - APDs are checked for affected part and serial numbers
- - - if none of the affected APD part and serial numbers are found no further action is
required
- - - If any APDs installed at seven locations match the serial number and part number
listed in the T able 1, the ON AIRCRAFT TEST is done
- - - if the tests are passed, APD’s are secured properly
- - - the applicable operational tests are done
- - - if the test is failed, the affected APD(s) are replaced.
- - - the applicable operational tests are done
- - - close out.
D. Compliance
Bombardier Inc. recommends incorporation of this Service Bulletin at the earliest
opportunity unless otherwise directed by the operator’s airworthiness authority.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
# 9 3 --- Q --- 0 2 .

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 4 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F. M a n p o w e r
It will take an estimated 9.00* man- - -hour s to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 2.00
Procedure 3.00*
T e s t/R T S 2.00
Close- - -Out 2.00
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure tim e, part fabrication, tool acquisition or lost
time.
NOTE: * Estimated time may vary, if it is required to replace APD’s.
G. Material - - - Price and Availability
Refer to merged Kidde Aerospace & Defense Service Bulletin 10- - -1096- - -26- - -511
H. T ooling - - - Price and Availability
Refer to merged Kidde Aerospace & Defense Service Bulletin 10- - -1096- - -26- - -511
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected
K. Publications Affected
ModSums Manual PSM 1- - -84- - -12..................................

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 5 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
L. References
Revision ’A’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
Kidde Aerospace & Defense Service Bulle tin 10- - -1096- - -26- - -511 Rev 2 Oct 11/18
PCA 47056 Revision 00 (for internal reference only)
D H 8 --- 4 0 0 --- S L --- 2 6 --- 0 0 4 K I D D E A e r o s p a c e & D e f e n s e S E R V I C E I N F O R M A T I O N
LETTER (SIL) 2018- - -02
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
None
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
Refer to merged Kidde Aerospace & Defense Service Bulletin 10- - -1096- - -26- - -511
D. Existing Parts Accountability
Refer to enclosed Kiddie service bulletin 10- - -10- - -96- - -26- - -511.
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of Bombardier in the CRC at
1- - -844- - -272- - -2720 (1- - -844- - -CRC- - -CRC0) or email at thd.qseries@aero.bombardier.comfor
analysis and to get an approved disposition to complete this service bulletin.

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 6 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
A . J o b S e t --- U p
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K ’ S 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(2) Make sure the aircraft is in standard configuration for maintenance (refer to AMM
TASK 12- - -00- - -01- - -860- - -801)
(3) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(4) Make sure the nose gear ground lock is engaged.
(5) Set wheel chocks in front and behind the landing gear tires.
(6) Set up work platforms or ladders around the No.1 and No.2 nacelles. Make sure
that the work platforms or ladders are electrically grounded.
(7) Set up work platforms or ladders near APU compartment. Make sure that the
work platforms or ladders are electrically grounded.

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 7 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
B. PROCEDURE
NOTE: Parts A, B and C must be completed to meet the intent of this service
bulletin.
P a r t A --- L e f t H a n d N a c e l l e
(1) Refer to applicable instructions in AMM TASK 26- - -11- - -01- - -000- - -801 to gain
access to the Engine Primary Zone APD. (refer to Figure 1)
(2) Refer to applicable instructions in AMM TASK 26- - -11- - -03- - -000- - -801 to gain
access to the Propeller Electronic- - -Control APD. (refer to Figure 2)
(3) Refer to applicable instructions in AMM TASK 26- - -11- - -06- - -000- - -801 to gain
access to the MLG Primary Zone APD. (refer to Figure 3)
(4) If required, clean APDs using a chemical and/or abrasive cleaning method. (refer
to AMM TASK 26- - -10- - -00- - -110- - -801 and TASK 26- - -10- - -00- - -120- - -801)
(5) Inspect each Advance Pneumatic Detector (APD) installed on all three locations
to determine the serial number and part number is listed in the effectivity section
of the Kidde Aerospace & Defense Service Bulletin 10- - -1096- - -26- - -511.
NOTE: T o see the serial number and on the APD, it may be required to loosen
or remove the clamps that secure the APD.
(6) If the APD serial number and part number is not listed in the T able 1, no further
action is required.
(a) Make sure APD is secured properly. Do the applicable operational test (refer to
applicable AMM installation TASK listed in T able 2) and complete the Close Out.
(7) If the APD serial number and part number is listed in the T able 1 do the steps that
follow:
(a) Energize the electrical system. (refer to AMM TASK 24- - -00- - -00- - -861- - -801)
(b) Do the ON AIRCRAFT TEST (3.1) given in the Kidde Aerospace & Defense
Service Bulletin 10- - -1096- - -26- - -511.
(8) If the test is passed, re identify APD refer to enclosed Kiddie service bulletin

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 8 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
10- - -1096- - -26- - -511 and AMM TASK 20- - -00- - -01- - -910- - -801.
(a) Make sure APD is secured properly and do the operational test (refer AMM
TASK 26- - -11- - -00- - -710- - -801) and complete theClose - - - Out.
(9) If the test is failed, replace the APD (refer to applicable AMM TASK listed in T able
2. Do the applicable operational test (refer to applicable AMM installation TASK
listed in T able 2) and complete the Close Out.
(a) Return all failed APD(s) to Kidde Aerospace & Defense refer to enclosed Service
Bulletin 10- - -1096- - -26- - -511.
Part B - - - Right Hand Nacelle
(1) Refer to applicable instructions in AMM TASK 26- - -11- - -01- - -000- - -801 to gain
access to the Engine Primary Zone APD. (refer to Figure 1)
(2) Refer to applicable instructions in AMM TASK 26- - -11- - -03- - -000- - -801 to gain
access to the Propeller Electronic- - -Control APD. (refer to Figure 2)
(3) Refer to applicable instructions in AMM TASK 26- - -11- - -06- - -000- - -801 to gain
access to the MLG Primary Zone APD. (refer to Figure 3)
(4) If required, clean APDs using a chemical and/or abrasive cleaning method. (refer
to AMM TASK 26- - -10- - -00- - -110- - -801 and TASK 26- - -10- - -00- - -120- - -801)
(5) Inspect each Advance Pneumatic Detector (APD) installed on all three locations
to determine the serial number and part number is listed in the effectivity section
of the Kidde Aerospace & Defense Service Bulletin 10- - -1096- - -26- - -511.
NOTE: T o see the serial number and on the APD, it may be required to loosen
or remove the clamps that secure the APD.
(6) If the APD serial number and part number is not listed in the T able 1, no further
action is required.
(a) Make sure APD is secured properly and complete the Close Out
(7) If the APD serial number and part number is listed in the T able 1 do the steps that
follow:

### Page 11

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 9 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
(a) Energize the electrical system. (refer to AMM TASK 24- - -00- - -00- - -861- - -801)
(b) Do the ON AIRCRAFT TEST (3.1) given in the Kidde Aerospace & Defense
Service Bulletin 10- - -1096- - -26- - -511.
(8) If the test is passed, re- - -identify APD refer to enclosed Kiddie service bulletin
10- - -1096- - -26- - -511 and AMM TASK 20- - -00- - -01- - -910- - -801.
(a) Make sure APD is secured properly and do the operational test (refer AMM
TASK 26- - -11- - -00- - -710- - -801). and complete theClose - - - Out.
(9) If the test is failed, replace the APD (refer to applicable AMM TASK listed in T able
2. Do the applicable operational test (refer to applicable AMM installation TASK
listed in T able 2) and complete the Close Out.
(a) Return all failed APD(s) to Kidde Aerospace & Defense refer to enclosed Service
Bulletin 10- - -1096- - -26- - -511.
P a r t C --- A P U
(1) Refer to applicable instructions in AMM TASK 26- - -13- - -01- - -000- - -801 to gain
access to the APU compartment APD. (refer to Figure 4)
(2) If required, clean APD using a chemical and/or abrasive cleaning method. (refer
to AMM TASK 26- - -10- - -00- - -110- - -801 and TASK 26- - -10- - -00- - -120- - -801)
(3) Inspect the Advance Pneumatic Detector (APD) installed to determine the serial
number and part number is listed in the effectivity section of the Kidde Aerospace
& Defense Service Bulletin 10- - -1096- - -26- - -511.
NOTE: T o see the serial number and on the APD, it may be required to loosen
or remove the clamps that secure the APD.
(4) If the APD serial number and part number is not listed in the T able 1, no further
action is required.
(a) Make sure APD is secured properly and complete the Close Out.

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 10 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
(5) If the APD serial number and part number is listed in the T able 1 do the steps that
follow:
(a) Open and tag the circuit breakers that follow: (refer to applicable instructions in
AMM TASK 26- - -23- - -06- - -000- - -801)
CB PANEL AND CB NO NAME
LEFT DC (ESSENTIAL), J7 FIRE DET ENG 1VLV IND
LEFT DC (ESSENTIAL), K7 FIRE DET ENG 1 IND
RIGHT DC (ESSENTIAL), G7 FIRE DET APU IND
RIGHT DC (ESSENTIAL), H7 FIRE DET ENG 2 VLV IND
RIGHT DC (ESSENTIAL), J7 FIRE DET ENG 2 IND
RIGHT DC (ESSENTIAL), F2 BATTERY PWR - - - FIRE EXT CONT
AMP 1&2 ENG
RIGHT DC (ESSENTIAL), G2 BATTERY PWR - - - FIRE EXT CONT
AMP CARGO
RIGHT DC (ESSENTIAL), K1 BATTERY PWR - - - APU/CARGO MAN
EXT
(b) Disconnect the APU fire extinguisher bottle electrical connector from the
cartridge. Put a plastic cap on the electrical connector. Do not remove the
cartridge.
(c) Install a shunt plug or a non- - -conductive blanking cap on the electrical
connector on the cartridge.
(d) Remove the tags and close the circuit breakers that follow:
CB PANEL AND CB NO NAME
LEFT DC (ESSENTIAL), J7 FIRE DET ENG 1VLV IND
LEFT DC (ESSENTIAL), K7 FIRE DET ENG 1 IND

### Page 13

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 11 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
CB PANEL AND CB NO NAME
RIGHT DC (ESSENTIAL), G7 FIRE DET APU IND
RIGHT DC (ESSENTIAL), H7 FIRE DET ENG 2 VLV IND
RIGHT DC (ESSENTIAL), J7 FIRE DET ENG 2 IND
RIGHT DC (ESSENTIAL), F2 BATTERY PWR - - - FIRE EXT CONT
AMP 1&2 ENG
RIGHT DC (ESSENTIAL), G2 BATTERY PWR - - - FIRE EXT CONT
AMP CARGO
RIGHT DC (ESSENTIAL), K1 BATTERY PWR - - - APU/CARGO MAN
EXT
(e) Energize the electrical system. (refer to AMM TASK 24- - -00- - -00- - -861- - -801)
(f) Do the ON AIRCRAFT TEST (3.1) given in the Kidde Aerospace & Defense
Service Bulletin 10- - -1096- - -26- - -511.
(6) If the test is passed, re identify APD refer to enclosed Kiddie service bulletin
10- - -1096- - -26- - -511 and AMM TASK 20- - -00- - -01- - -910- - -801.
(a) Open and tag the circuit breakers that follow: (refer to applicable instructions in
AMM TASK 26- - -23- - -06- - -000- - -801)
CB PANEL AND CB NO NAME
LEFT DC (ESSENTIAL), J7 FIRE DET ENG 1VLV IND
LEFT DC (ESSENTIAL), K7 FIRE DET ENG 1 IND
RIGHT DC (ESSENTIAL), G7 FIRE DET APU IND
RIGHT DC (ESSENTIAL), H7 FIRE DET ENG 2 VLV IND
RIGHT DC (ESSENTIAL), J7 FIRE DET ENG 2 IND

### Page 14

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 12 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
CB PANEL AND CB NO NAME
RIGHT DC (ESSENTIAL), F2 BATTERY PWR - - - FIRE EXT CONT
AMP 1&2 ENG
RIGHT DC (ESSENTIAL), G2 BATTERY PWR - - - FIRE EXT CONT
AMP CARGO
RIGHT DC (ESSENTIAL), K1 BATTERY PWR - - - APU/CARGO MAN
EXT
(b) Reconnect electrical connector on APU fire extinguisher bottle. (refer to
applicable instructions in AMM TASK 26- - -23- - -06- - -400- - -801)
(c) Remove the tags and close the circuit breakers that follow:
CB PANEL AND CB NO NAME
LEFT DC (ESSENTIAL), J7 FIRE DET ENG 1VLV IND
LEFT DC (ESSENTIAL), K7 FIRE DET ENG 1 IND
RIGHT DC (ESSENTIAL), G7 FIRE DET APU IND
RIGHT DC (ESSENTIAL), H7 FIRE DET ENG 2 VLV IND
RIGHT DC (ESSENTIAL), J7 FIRE DET ENG 2 IND
RIGHT DC (ESSENTIAL), F2 BATTERY PWR - - - FIRE EXT CONT
AMP 1&2 ENG

### Page 15

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 13 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
CB PANEL AND CB NO NAME
RIGHT DC (ESSENTIAL), G2 BATTERY PWR - - - FIRE EXT CONT
AMP CARGO
RIGHT DC (ESSENTIAL), K1 BATTERY PWR - - - APU/CARGO MAN
EXT
(d) Make sure APD is secured properly and do the operational test (refer AMM
TASK 26- - -13- - -00- - -710- - -801) and complete theClose - - - Out.
(7) If the test is failed, replace the APD (refer to applicable AMM TASK listed in T able
2. Do the applicable operational test (refer to applicable AMM installation TASK
listed in T able 2) and complete the Close Out.
APD Location Removal AMM T ask Installation AMM T ask
Engine Primary Zone
(LH and RH Nacelle )
TASK
2 6 --- 1 1 --- 0 1 --- 4 0 0 --- 8 0 1
TASK
2 6 --- 1 1 --- 0 1 --- 4 0 0 --- 8 0 1
Propeller Electronic
Control (PEC)
(LH and RH Nacelle)
TASK
2 6 --- 1 1 --- 0 3 --- 0 0 0 --- 8 0 1
TASK
2 6 --- 1 1 --- 0 3 --- 4 0 0 --- 8 0 1
Main Landing Gear
Primary Zone
(LH and RH Nacelle)
TASK
2 6 --- 1 1 --- 0 6 --- 0 0 0 --- 8 0 1
TASK
2 6 --- 1 1 --- 0 6 --- 4 0 0 --- 8 0 1
APU APD TASK2 6 --- 1 3 --- 0 1 --- 0 0 0 --- 8 0 1 TASK2 6 --- 1 3 --- 0 1 --- 4 0 0 --- 8 0 1
Ta b l e 2

### Page 16

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 14 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
C. Close Out
(1) De- - -energize the electrical system. (refer to AMM TASK 24- - -00- - -00- - -861- - -802)
(2) Remove all tools and equipment from the work area.
(3) Close all the panels and doors that were opened and removed for the test.
(4) On completion of this service bulletin, make the following entry in the appropriate
logbooks: “Service Bulletin 84- - -26- - -19 {Fire Protection - - - Fire Detection System
- - - Nacelle and Auxiliary Power Unit (APU) - - - Advanced Pneumatic Detectors
(APD) - - - Special Inspection, T esting and Rectification} accomplished.”

### Page 17

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 15 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
Engine Primary Zone APD - - - Location
Figure 1
A
A
A
B
B
APD
GROMMET(TYP .)
SENSING ELEMENT(TYP .)
ELECTRICAL
CONNECTOR

### Page 18

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 16 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
Propeller Electronic Control (PEC) APD - - - Location
Figure 2
SENSING ELEMENT (TYP.)
APD
ELECTRICAL CONNECTOR
GROMMET (TYP .)

### Page 19

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 17 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
MLG Primary Zone APD - - - Location
Figure 3
B
C
B
A
C
(TYPICAL 38 PLACES)
GROMMET (TYP .)
SENSING ELEMENT (TYP .)
HINGED CLAMP
APD
ELECTRICAL
CONNECTOR

### Page 20

S E R V I C E B U L L E T I N 8 4 --- 2 6 --- 1 9
S . B . 8 4 --- 2 6 --- 1 9
Page 18 of 18
24 Oct 2018
BMRevision ‘A’ 11 Feb 2019
APU Compartment APD - - - Location
Figure 4
A
A
C
ADP
C
B
HINGED CLAMP
B
ELECTRICAL CONNECTOR
SENSING ELEMENT
GROMMET
1
1

### Page 21

May2018
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 22

May 2018
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
