# Bombardier Service Bulletin 84-27-44

Copy: No revision named ("SB 84-27-44 Rev-B dated 11 Feb 2014"), 18 pages: PDF https://openairdocs.org/files/sha256/bf/84/bf84de32c826c10a04302724676f15846179e50f14ed9ce0ee41d6360891c0b2; text https://openairdocs.org/service-documents/bombardier/sb-84-27-44/file/bf84de32c826.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0144; AD 2014-19-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-27-44
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-27-44

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2014-19-02](https://openairdocs.org/ad/2014-19-02.md), effective Oct 24, 2014: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-27-44/proposed.md).

## Text (18 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0144; AD 2014-19-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘B’ 11 Feb 2014
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
Flight Controls - - - Rudder Control Surfaces - - - Fore Rudder - - - Special
Inspection for Correct Installation of Bearings
This page transmits Revision ‘B’ of Service Bulletin 84- - -27- - -44, pages 1 thru
16, dated 11 Feb 2014.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- t h ePLANNING INFORMATION section D. Compliance on page 3 is
revised to add Transport Canada Airworthiness Directive CF- - -2013- - -34.
--- t h ePLANNING INFORMATION section L. References on page 4 is revised
to show Revision ‘B’ of this service bulletin was prepared to the related data
that follows and also to add Transport Canada Airworthiness Directive
CF- - -2013- - -34.
--- t h eACCOMPLISHMENT INSTRUCTIONS section B. Procedure on page 8
NOTE is clarified.
--- t h eACCOMPLISHMENT INSTRUCTIONS section C. Close Out on page 9
step (5) is revised to correct the referenced task number. Was TASK
27- - -20- - -01- - -710- - -802 now TASK 27- - -20- - -00- - -710- - -802.
The Compliance in the previous issue of this service bulletin is not affected
by this revision. No additional rework to the aircraft is introduced by this
revision.
Remove Service Bulletin 84- - -27- - -44 Revision A and replace with attached.
Previous issue of Service Bulletin 84- - -27- - -44:
Initial issue - - - Pages 1 thru 14 dated 13 Apr 2009
Rev A - - - Pages 1 thru 16 dated 10 Jun 2009

### Page 2

(No text on this page.)

### Page 3

D
S . B . 8 4 --- 2 7 --- 4 4
Page 1 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2723 NUMBER: 84- - -27- - -44
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGES OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Flight Controls - - - Rudder Control Surfaces - - - Fore Rudder - - - Special
Inspection for Correct Installation of Bearings
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4166
thru 4175.
Production: A line check is done before delivery of DHC- - -8 Models 401
and 402 Serial Number 4176 and subsequent per Line Check
37422.
NOTE: The instructions in this Service Bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 2 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Spares Affected:
None
B. Reason
Problem: Bombardier production line inspection have reported that (upper and/or
lower) installed bearings in the fore rudder have migrated from their
housing on several aircraft.
Cause: The bearings had not been properly installed with adhesive (Loctite
Grade AA ) and sealed per engineering requirements.
Solution: A special inspection and if required rectification is accomplished to
confirm that affected bearings are correctly installed and sealed.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- - - #1 and #2 hydraulic systems are pressurized
- - - the flaps are set to greater than 5 degrees
- - - the rudder is swung full trailing- - -edge left and held
- - - #1 and #2 hydraulic systems are de- - -pressurized
- - - safety stands are placed behind the rudder
- - - access panels 323CR and 323BR are removed from the fore rudder
- - - rivets are drilled off and cover 85547207- - -103 is removed, if required, to proof
load test installed bearing
- - - PCU actuator rod is detached from existing fore rudder hinge bracket assembly
- - - existing bearings are then visually inspected and then proof load tested, if the
bearing passes proof load, no additional action is required
--- PA R T A INSPECTION of the Procedures section gives the instructions to
inspect the bearing for correct installation in the fore rudder
--- PA R T B RECTIFICATION of the Procedures section gives the instructions for
removal of bearings, inspection of the exi sting bore, installation of bearing with
adhesive Loctite Grade AA, proof load bearing test and the application of
sealant to the existing bearings in the fore rudder
- - - the PCU actuator rod is attached to the existing fore rudder hinge bracket
assembly using retained hardware
- - - cover 85547207- - -103 is installed to fore rudder with rivets

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 3 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
- - - previously removed access panels are installed with retained hardware
- - - an operational check of the rudder system is done
- - - close out.
D. Compliance
Bombardier Inc. recommend that the spe cial inspection/rectification be
incorporated at the earliest opportunity unless otherwise directed by the operator’s
airworthiness authority.
Transport Canada Airworthiness Directive CF- - -2013- - -34.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
O r g a n i z a t i o n N o : D A O # 9 3 --- Q --- 0 2 .
F. M a n p o w e r
PART A - - - Special Inspection for Correct Installation of Bearings - - - Fore Rudder
It will take an estimated 6.50 man- - -hours to complete PART A of the
ACCOMPLISHMENT instructions in this s ervice bulletin. The breakdown of man
- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 2.00
Procedure in Part A 1.50
T e s t/R T S 1.00
Close- - -Out 2.00
PART B - - - Rectification Procedure for Incorrect Installation of Bearing - - - Fore
Rudder
It will take an estimated 8.0 man- - -hours to complete PART B of the
ACCOMPLISHMENT instructions in this s ervice bulletin. The breakdown of man
- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 2.00
Procedure in Part B 3.00
T e s t/R T S 1.00
Close- - -Out 2.00

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 4 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
G. Material - - - Price and Availability
None
H. T ooling - - - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
None
L. References
Revision ‘B’ of this service bulletin was prepared to the related data that follows:
PCA 42445 Revision - - - (for internal reference only)
Transport Canada Airworthiness Directive CF- - -2013- - -34.
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
None
NOTE: This service bulletin is self- - -contained (illustrated). No drawings will be
supplied.
(1) The following materials are required for the completion of this service bulletin
and may be procured as single items from Bombardier Aerospace Regional
Aircraft or purchased directly from industry sources.
Addresses of manufacturers and suppliers not shown below are listed in 400
Series Aircraft, in Consumable Products Manual PSM 1- - -84- - -18.

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 5 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Part Number Qty. Per Aircraft Description Remarks
MIL- - -R- - -81533 1 Ounce Solvent Trichloroethane,
1,1,1 or
DHMS S5.01 Class 2 1 Ounce Solvent Dynamold, Spec
AMS 3167
MIL- - -S- - -22473 1 Ounce Sealant Loctite, Grade AA
Loctite 7387 1 Ounce Sealant,Activator Loctite, Activator,
Grade N
DHMS S3.01,T ype II,
Class B
1 Ounce Sealant PR1776M B1/2
or PR1776M B2
As Required Wiper Cloth White, Cotton
L i n t --- F r e e C l o t h
1M a r k e r Red Marker Martex Corp.
B0205018AD4- - -4S 8 Rivet
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
Part Number Description Remarks
Dillon Model U 30354- - -0058
or Equivalent Force Gage
Force Gage S e eN o t e1
C --- C l a m p
NAS43HT10- - -8 Spacer (Qty 1) S e eN o t e2
NAS43HT14- - -8 Spacer (Qty 1) S e eN o t e2
AN970- - -4 Washer
NOTE 1: Commercially available support hardware for proof loading may be
substituted for equivalent to suit individual force gage geometry.
NOTE 2: In the event that spacers listed are difficult to procure, operators are
permitted to locally manufacture spacers if required. Refer to Figure 6

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 6 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
for equivalent spacer dimensions and material specifications.
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE
MOVEMENT OF FLIGHT CONTROL SURFACES. MOVEMENT OF THE
FLIGHT CONTROL SURFACES CAN CAUSE INJURIES TO PERSONS
AND DAMAGE TO THE EQUIPMENT .
(1) Pressurize # 1 and # 2 hydraulic systems. Refer to Aircraft Maintenance Manual
PSM 1- - -84- - -2, TASK 29- - -00- - -00- - -863- - -801.
(2) Set flaps to greater than 5 degrees.
(3) Apply rudder pedal full trailing- - -edge left and hold.
(4) De- - -pressurize #1 and #2 hydraulic systems. Refer to Aircraft Maintenance
Manual PSM 1- - -84- - -2, TASK 29- - -00- - -00- - -863- - -802.
(5) Release rudder pedal and make sure no further pedal input is applied. The
rudder should remain in the deflected left position.
(6) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS detailed in Maintenance Manual PSM 1- - -84- - -2.
Refer to Aircraft Maintenance Manual PSM 1- - -84- - -2, TASK
24- - -00- - -00- - -861- - -802.
(7) Install workstands on both sides of the rudder to safely reach the center main
hinge fittings as required. Make sure the w orkstands are electrically grounded.
WARNING: BE SURE THAT THE HYDRAULIC PRESSURE IS OFF , AND THAT
THERE IS NO PRESSURE IN THE HYDRAULIC SYSTEM. IF YOU DO
NOT DO THIS YOU CAN INJURIES TO PERSONS AND DAMAGE TO
THE EQUIPMENT .
(8) Remove and retain fore rudder hinge bracket assembly access panels 323 CR
and 323 BR, (RHS) and mounting hardware. Refer to Figure 1.
(9) Carefully drill off rivets B0205018AD4- - -4S attaching cover 85547207- - -103 to fore
rudder. Do not elongate rivet holes or damage countersink. Remove cover
85547207- - -103 to allow proof load tool to access fore rudder hinge bracket
assembly 85547217- - -001 and - - -002. Refer to Figure 2.

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 7 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
NOTE: The skin consists of three parts, cover 85547207- - -103, Rib
85547208- - -103 and shim CSP 471- - -160- - -030- - -070- - -048.
(10) Disconnect each rudder PCU rod from the hinge bracket assembly as follows :
(a) Remove and discard the cotter pin MS24665- - -302. Refer to Figure 3.
(b) Remove and retain nut MS1414L6 and washer AN960D616L.
(c) Remove and retain the bolt NAS6706D14 from the end of the PCU actuator
rod and fore rudder hinge bracket assembly.
B. Procedure
NOTE: Instructions in PART A and PART B are given for upper hinge bracket
assembly 85547217- - -001. Repeat procedure in PART A and PART B for
lower bracket assembly 85547217- - -002.
PART A INSPECTION
(1) Set up proof load tester, Dillon Model U 30354- - -0058 or equivalent force gage
and C- - -clamp, to the fore rudder hinge bracket assembly 85547217- - -001. Refer
to Figure 5.
(2) Proof load existing bearing DSC8- - -6 in- - -situ to 132 lbs. Apply load by slowly
tightening C- - -Clamp. During proof load testing, any slippage or freeplay (relative
movement between the bearing and fitting) is deemed as unacceptable.
(3) If bearing fails proof load test, refer to PART B RECTIFICATION section.
NOTE: Make sure spacer, (support) NAS43HT10- - -8 or equivalent, contacts
bearing race only .
NOTE: Make sure spacer, (support) NAS43HT14- - -8 or equivalent, contacts fitting
85574217- - -001 and washer, (support) AN970- - -4 on C- - -Clamp.
(4) If existing bearing passes the proof load test, no further additional action is
required. Refer to C. Close Out section.
(5) Inspect area adjacent to the proof load tested bearings for a small red dot, if no
dot is present, identify area using a Dalo marker or equivalent paint marker.
Refer to Figure 5.
(6) If bearings have not been sealed, apply sealant DHMS S3.01, T ype II, Class B
between the outside circumference of the installed bearing (both sides) and fore
rudder hinge bracket assembly 85547217- - -001.

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 8 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
NOTE: Do not allow sealant to enter bearings.
PART B RECTIFICATION
(1) If existing bearing fails proof load test, remove bearing DSC8- - -6 from fore
rudder hinge bracket assembly 85547217- - -001.
(2) Carefully remove sealant (if applicable) with a plastic or phenolic scraper from
bearing and top/bottom surfaces of fore rudder hinge bracket assembly.
NOTE: Do not use metal scrapers to remove sealant. Metal scrapers will damage
the surface.
(3) Inspect bearing DSC8- - -6 for damage, corrosion and dimension conformity.
Outside diameter of bearing should be 0.8120 to 0.8125 inch diameter.
NOTE: The existing bearings DSC8- - -6 may be reused if no damage, corrosion
and dimensional non- - -conformity is evident.
(4) Inspect fitting bore of the fore rudder hinge bracket assembly 85547217- - -001 as
follows:
(a) Carefully inspect bore of the fore rudder hinge bracket assembly, using
flashlight and inspection mirror, for damage, corrosion and dimension
conformity.
(b) If damage, corrosion or dimensional non- - -conformity is evident, carefully
ream the inside diameter with a 0.8140 inch diameter reamer.
(c) If bore is worn or damaged beyond 0.8140 inch diameter, a repair
disposition (RD) will be required from Bombardier. Contact the T echnical
Help Desk department.
(5) Install new or existing DSC8- - -6 bearing into the fore rudder hinge bracket
assembly 85547217- - -001 with sealant MIL- - -S- - -22473 as follows:
(a) Solvent wipe the fitting bore of the fore rudder hinge bracket assembly and
bearings with a clean, cotton lint- - -free cloth dampened with solvent
MIL- - -R- - -81533 or solvent DHMS S5.01, Class 2. Refer to Structural Repair
Manual, PSM 1- - -84- - -3 , 51- - - 22 - - -40, Loctite Sealant Bonding procedure.
Refer to Figure 5.
NOTE: When cleaning sealed, grease lubricated bearings, make sure that no
solvent enters the sealed bearing and contaminates the lubricant.
NOTE: Handle all clean parts with clean lint- - -free cotton gloves.

### Page 11

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 9 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
(6) Proof load installed bearings to 132 pounds with Dillon Model U 30354- - -0058 or
equivalent force gage. Refer to Figure 5.
(7) Identify proof loading test by applying a small red dot adjacent to the bearing
using a Dalo marker or equivalent.
(8) Seal the outer circumference of the installed bearing DSC8- - -6 to fore rudder
hinge bracket assembly 85547217- - -001 (on both sides of installed bearing) with
sealant DHMS S3.01, T ype II, Class B. Refer to Figure 5.
NOTE: Do not allow sealant to enter bearings.
(9) Identify fore rudder hinge bracket assembly 85547217- - -001 with “SB
84- - -27- - -44” in a suitable area using a thin permanent marker.
C. Close Out
(1) Reconnect the rudder PCU rod to the hinge bracket. Install with retained bolt
NAS6706D14, retained washers AN960D616L (one under bolt head), retained
MS14144L6 nut and new cotter pin MS24665- - -302. Refer to Figure 3.
(2) Make sure the shim CSP 471- - -160- - -030- - -070- - -048 is installed between the rib
85547208- - -103 and cover 85547207- - -103. Install cover 85547207- - -103 with
rivets B0205018AD4- - -4S. Refer to Figure 2.
(3) Install access panels 323CR and 323BR with retained hardware.
(4) Remove all tools and equipment from the work area.
(5) Do the operational check of the rudder control system. Refer to Aircraft
Maintenance Manual, PSM 1- - -84- - -2, TASK 27- - -20- - -00- - -710- - -802.
(6) On completion of this service bulletin, make the following entry in the
appropriate logbooks: “Service Bulletin 84- - -27- - -44 Flight Controls - - - Rudder
Control Surfaces - - - Fore Rudder - - - Special Inspection for Correct Installation of
Bearings accomplished”.

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 10 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Fore Rudder Access Panels
Figure 1
FORE
RUDDER
mhwf1a01.cgm
COVER
85547207- - -103
323CL
323BL
323CR
323BR
(REFERENCE)
(REFERENCE)
ACCESS PANEL
ACCESS PANEL
Z107
110.031
ACCESS PANEL
ACCESS PANEL
Z107
124.031
D
B

### Page 13

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 11 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Removal/Installation of Cover
Figure 2
COVER
85547207- - -103
RIB
85547208- - -103
SHIM
CSP471- - -160- - -030- - -070- - -048
NOTE:
ACCESS PANEL
323CR
ACCESS PANEL
323BR
COVER 85547207- - -103 CONSISTS OF RIB 85547208- - -103
RIVET
B0205018AD4- - -4S
AND SHIM CSP471- - -160- - -030- - -070- - -048
(QTY 8 REQUIRED)
FORE RUDDER
HINGE LINE
D
Z107
110.031
124.031
Z107
ALL MEASUREMENTS ARE IN INCHES
NOTE:

### Page 14

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 12 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Removal/Installation of PCU Rudder Actuator Rod
Figure 3
BOL T
NAS6706D14
PCU ACTUATOR ROD
WASHER
AN960D616L
NUT
AN960D616L
WASHER
MS14144L6
COTTER PIN
MS24665- - -302
BEARING
D S C 8 --- 6
FORE RUDDER
HINGE BRACKET
ASSEMBL Y
85547217- - -001/- - -002
RUDDER PCU
B

### Page 15

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 13 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
Installation/Removal of Bearing DSC8- - - 6
Figure 4
BEARING
D S C 8 --- 6
BEARING
D S C 8 --- 6
FORE RUDDER
HINGE BRACKET
ASSEMBL Y
85547217- - -001
FORE RUDDER
FORE RUDDER
HINGE BRACKET
ASSEMBL Y
85547217- - -002
D
D

### Page 16

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 14 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
MIL- - -S- - -22473
FITTING
85547217- - -001/- - -002 BEARINGD S C 8 --- 6
INSTALL BEARING DSC8- - -6 WITH SEALANT
PROOF MARK WITH DALO
MARKER OR EQUIVALENT
BETWEEN FITTING AND THE OUTER CIRCUMFERENCE
OF THE INSTALLED BEARING DSC8- - -6 (BOTH SIDES)
APPL Y SEALANT DHMS S3.01, TYPE II, CLASS B
Proof Loading Bearing T est / Sealant Application
Figure 5
PROOF LOAD BEARING
DSC8- - -6 TO 132 POUNDS
FITTING
BEARING
D S C 8 --- 6
85547217- - -001/- - -002
DILLON MODEL U
30354- - -0058 FORCE
GAGE OR EQUIVALENT
C --- C L A M P
SPACER, (SUPPORT)
NAS43HT14- - -8 OR EQUIVALENT
WASHER, (SUPPORT)
AN970- - -4 OR EQUIVALENT
SPACER, (SUPPORT)
NAS43HT10- - -8 OR EQUIVALENT
PROOF LOAD BEARING TEST
APPLICATION OF ADHESIVE AND SEALANT TO BEARING
1

### Page 17 (OCR)

SERVICE BULLETIN 84-27-44
0.120
0.130
- OD
DIAMETER  OD  ID
DASH NUMBER.  MIN TO MAX
NIW  MAX  MIN  MAX
10  0.120  0.735  0.765  0.627  0.677
14  0.930  0.985  1.015  0.877  0.927
NOTE: 1. ALL DIMENSIONS IN INCHES
2. REMOVE ALL BURRS
3. SPACERS ARE SUPPORT HARDWARE FOR PROOF LOADING.
THEY ARE NOT PART OF THE AIRCRAFT.
4. LISTED DIMENSIONS ARE SUGGESTED DIMENSION TO SUIT
DILLON MODEL U FORCE GAGE. IF ALTERNATE FORCE GAGE
IS USED, OPERATORS ARE PERMITTED TO DEVIATE FROM
LISTED DIMENSIONS TO SUIT INDIVIDUAL FORCE GAGE
GEOMETRY.
MATERIAL
ALLOY STEEL TUBING
GENERAL CODE
NAS43HT - (DIAMETER DASH NUMBER) - (LENGTH DASH NUMBER)
Equivalent Spacer Dimensions and Material Specifications
Figure 6
13 Apr 2009  S.B. 84-27-44
Revision 'B' 11 Feb 2014  Page 15 of 16
MD

### Page 18

S E R V I C E B U L L E T I N 8 4 --- 2 7 --- 4 4
S . B . 8 4 --- 2 7 --- 4 4
Page 16 of 16
13 Apr 2009
Revision ‘B’ 11 Feb 2014
MD
This Page Intentionally Blank
1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
