# Bombardier Service Bulletin 84-28-09

Copy: Revision D ("SB 84-28-09 RD"), 23 pages: PDF https://openairdocs.org/files/sha256/5d/03/5d036d8596fb73ed8051887b65dfec50e0395059479a0763e9d8abe6f091371e; text https://openairdocs.org/service-documents/bombardier/sb-84-28-09/file/5d036d8596fb.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-28-09
- Latest revision known: 84-28-09, Revision D, dated January 29, 2013 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-28-09

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-17-25](https://openairdocs.org/ad/2015-17-25.md), effective Oct 7, 2015: Revision D

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-28-09/proposed.md).

## Text (23 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘D’ 29 Jan 2013
DHC-8 (DASH 8)
SERVICE BULLETIN 84-28-09
Fuel System - Center Wing - Engine Fuel Feed - Introduction of New
Tube Assemblies To Eliminate Fouling Conditions - ModSum 4-113643
This page transmits Revision ‘D’ of Service Bulletin 84-28-09, pages 1 thru
18 dated 29 Jan 2013.
This service bulletin is re-issued in its entirety for the reasons that follow:
- deleted existing statements from page 1 of service bulletin
- modified existing statements on page 1, page 4 and page 6 of service
bulletin
- added new statement to page 1 of service bulletin
-t h e References section is revised to convey the latest revision of the service
bulletin and engineering documentation.
The Compliance in the previous issues of this service bulletin is not affected
by this revision. No additional rework to the aircraft is introduced by this
revision.
Remove the previous revision of Service Bulletin 84-28-09 and replace with
attached.
Previous issues of Service Bulletin 84-28-09:
Initial issue - Pages 1 thru 18 dated 22 Jun 2010
Revision ‘A’- Pages 1 thru 18 dated 01 Sep 2010
Revision ‘B’- Pages 1 thru 18 dated 14 Feb 2011
Revision ‘C’- Pages 1 thru 18 dated 17 Aug 2012

### Page 2

(No text on this page.)

### Page 3

D
S.B. 84-28-09
Page 1 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2812 NUMBER: 84-28-09
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fuel System - Center Wing - Engine Fuel Feed - Introduction of New
Tube Assemblies To Eliminate Fouling Conditions - ModSum 4-113643
Upon incorporation of SB 84-28-09, a fouling condition was identified due to the
post mod fuel pipe 82822144-003 (part of kit number 8MK4429-001).
In order to address this condition, Bombardier has issued Modsum 4-113754
(Bombardier Service Bulletin 84-28-14) which replaces pipe 82822144-003
introduced by SB 84-28-09.
-deleted-
-deleted-
If SB 84-28-09 is not incorporated or ModKit 8MK4429-001 has not been ordered
then it is required to incorporate SB 84-28-15 in lieu of SB 84-28-09 and SB
84-28-14.
All future installations will be accomplished using the latest issue of Service Bulletin
84-28-15.

### Page 4

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 2 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Model 402 Serial Number 4001, 4003, 4004,
4006, 4008 thru 4331.
Verification: ModSum 4-113643 has been installed on DHC-8 Aircraft
Model 402 Serial Number 4106.
Production: ModSum 4-113643 will be installed before delivery on
applicable DHC-8 Aircraft Models 401 and 402 at Serial
Number 4332 and subsequent.
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None
B. Reason
Problem: Operators of the Q400 aircraft have reported existence of a fouling
condition between engine fuel feed line (p/n 82822143) and the
feed-through hole in wing rib (p/n 85713381-109) at station Y-157.825
(right side fuel tank).
Other locations have been reported with inadequate clearance between
the fuel pipe and structure. In the event of a lightning strike a spark could
be produced at the fouling interface between pipe and structure.
Solution: This service bulletin introduces ModSum 4-113643.
The ModSum replaces five existing fuel lines (two in the left wing and three
in the right wing and supporting brackets) with new fuel lines and
supporting brackets.
The new fuel lines and brackets are designed to include different
geometric angles to ensure that when installed correctly contact with a
feed-through hole in a rib is eliminated and adequate clearance is
maintained. In addition, Teflon tubing is wrapped around one motive flow
line and scavenge lines in each fuel tank (left and right side) at specific
locations as part of the modification.

### Page 5

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 3 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- aircraft electrical power is removed
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- the fuel tanks are drained
- the engines are supported then specific fu el tank access panels (center and outer
wing) are removed
- r e s i d u a lf u e li sm o p p e du pa n dt h et a n ki sv e n t e d
- five existing fuel feed tube assemblies, four existing brackets, cushion clamps and
related hardware are removed
- new brackets, fuel feed lines are installed and secured using kept hardware
- the reworked ribs in each wing are re-identified with a new part number
- teflon sleeves are installed around a motive fuel line in each outer wing tank
- the new lines are pressure tested
- close out.
D. Compliance
Bombardier Inc. highly recommend that ModSum 4-113643 be incorporated at the
earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
A Transport Canada Airworthiness Directive Pending.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).

### Page 6

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 4 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
F. Manpower
It will take an estimated 35.00 man-hour s to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS MAN-HOURS TO
RWK LEFT WING
MAN-HOURS TO
RWK RIGHT WING
Job Set-Up *2.00 n/a n/a
Procedure /Test/
RTS
n/a 14.00 15.00
Close-Out **4.00 n/a n/a
* time required to defuel and vent fuel tank not included
** cure time for sealant not included.
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com
G. Material - Price and Availability
ModSum 4-113754 (Bombardier Service Bulletin 84-28-14) introduces a new
tube (part number 82822144-005) through Modification Kit 8MK4498-001, to
replace tube 82822144-003, which is part of the 8MK4429-001 kit. To use kit
8MK4429-001, it is required to replace tube part number 82822144-003 with
tube part number 82822144-005 obtained from kit 8MK4498-001 (SB 84-28-14).
ModKit 8MK4429-001 is available through the Customer Accounts Service Team at
Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial number(s) to:
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920

### Page 7

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 5 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
Kit Number Description
8MK4429-001 Engine Fuel Feed Line - Retrofit Kit
H. Tooling - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Maintenance Manual PSM 1-84-2................................
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
L. References
Revision ‘D’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4429 1 A
8Z6836 1 A
8Z9209 1 A
8Z9214 1 -
ModSum 4Q113643 Rev. ‘D’
ModSum 4-113643 Rev. ‘D’
Bombardier Service Bulletin 84-28-13 (ModSum 4-113745)

### Page 8

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 6 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
Bombardier Service Bulletin 84-28-14 (ModSum 4-113754)
Bombardier Service Bulletin 84-28-15 (ModSum 4-113762)
PCA 42939 Revision 4 (for internal reference only)
Transport Canada Airworthiness Directive Pending.
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
ModSum 4-113754 (Bombardier Service Bulletin 84-28-14) introduces a new
tube (part number 82822144-005) through Modification Kit 8MK4498-001, to
replace tube 82822144-003, which is part of the 8MK4429-001 kit. To use kit
8MK4429-001, it is required to replace tube part number 82822144-003 with
tube part number 82822144-005 obtained from kit 8MK4498-001 (SB 84-28-14).
(1) Modification Kit 8MK4429-001, Retrofit Kit - Engine Fuel Feed Line

### Page 9

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 7 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(2) Detailed Kit Content:
Quantity Per Kit
-001
Part Number Description
4 B0305078-04 Clamp
4 B0305078-10 Clamp
2 DSC411-6-0026 Teflon Hose
4 DSC411-12-032 Teflon Hose
4 B0205016AD5-8S Rivet, Solid
4 B0205016AD5-7S Rivet, Solid
1 85714430-003 Bracket Assy
1 85714428-003 Bracket Assy
1 85714527-001 Bracket Assy
1 85714426-003 Bracket Assy
14 MS29513-214 O-Ring
1 82822144-003 Tube Assy
1 82822143-003 Tube Assy
1 82822142-005 Tube Assy
1 82822140-003 Tube Assy
1 82822139-005 Tube Assy
1 8Z6836 Structural Provision Drawing
1 8Z9209 Retrofit Drawing
1 8Z9214 Retrofit Drawing

### Page 10

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 8 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non-indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
82822139-003 Tube Assy Eng
Feed (LH side)
1 A SAL 82822139-005 S
82822140-001 Tube Assy Eng
Fee (LH side)
1 A SAL 82822140-003 S
82822142-003 Tube Assy Eng
Feed (RH side)
1 A SAL 82822142-005 S
82822143-001 Tube Assy Eng
Feed (RH side)
1 A SAL 82822143-003 S
82822144-001 Tube Assy Eng
Feed (RH side)
1 A SAL 82822144-003 S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.

### Page 11

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 9 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate on
part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALLY
RETRACT. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE
TO THE EQUIPMENT.
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE LANDING GEAR
DOORS. MAKE SURE YOU DISCONNECT THE LANDING GEAR
DOORS. IF YOU DO NOT DO THIS THE LANDING GEAR DOORS WILL
CLOSE WHEN YOU APPLY THE HYDRAULIC PRESSURE. THIS CAN
CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.
WARNING: OBEY ALL THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK
ON THE FUEL SYSTEM AND/OR A FUEL SYSTEM COMPONENT. IF
YOU DO NOT YOU CAN CAUSE INJURIES TO PERSONS AND/OR
DAMAGE TO EQUIPMENT.
(1) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(2) Make sure the nose gear ground lock is engaged.
WARNING: YOU MUST REMOVE THE FUEL FROM THE FUEL TANK IN AN OPEN
AREA. IF YOU DO NOT DO THIS, YOU CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.

### Page 12

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 10 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(3) Refer to AMM TASK 28-10-00-840-801 and prepare fuel tank for access. Make
sure no fuel or fuel vapors are present before working on aircraft or in the fuel
tanks.
(4) Refer to AMM TASK’ 24-00-00-861-802, TASK 24-00-00-910-801 and placard and
select all aircraft electrical power to OFF. Obey all relevant WARNINGS and
CAUTIONS.
(5) Set up work platforms and/or ladders to permit access to the fuel tank access
panels between wing stations Y-42.000 and Y-317.019 left and right side wing.
Make sure that the work platforms or ladders are electrically grounded.
(6) Refer to AMM TASK 28-00-00-910-801 and make sure to obey the fuel system
safety precautions.
(7) Refer to AMM TASK 24-00-00-910-801 and make sure to obey the
electrical/electronic safety precautions.
(8) Refer to AMM TASK 24-00-00-910-802 and obey the electrostatic discharge
safety precautions.
CAUTION: MAKE SURE THAT THE FUEL TANKS ARE DRAINED BEFORE YOU
REMOVE THE ACCESS PANELS. IF YOU DO NOT DO THIS, YOU CAN
CAUSE DAMAGE TO THE WING STRUCTURE.
CAUTION: MAKE SURE THAT YOU DO NOT MOVE THE AIRCRAFT BEFORE YOU
INSTALL THE FUEL ACCESS PANELS. THIS IS NECESSARY TO
PREVENT DAMAGE TO THE WING AND THE WING BOX STRUCTURE.
(9) Refer to Figure 1, the applicable instructions in AMM TASK 57-11-01-000-801
and the table below and remove the left and/or right wing wet bay fuel tank
access panels.
ACCESS DESIGNATION
523AT (and/or 623AT right wing) Wet Bay Fuel Access Panels
522BT (and/or 622BT right wing) Wet Bay Fuel Access Panels
522CT (and/or 622CT right wing) Wet Bay Fuel Access Panels
(10) Refer to Figure 1, the applicable instructions in AMM TASK 57-21-01-000-801
and the table below and remove the outer wing fuel tank access panels.
ACCESS DESIGNATION
524AT (and/or 624AT right wing) Outer Wing Fuel Access Panels
524CT (and/or 624CT right wing) Outer Wing Fuel Access Panels

### Page 13

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 11 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(11) Use cotton cloths or a natural sponge to soak up the remaining fuel.
(12) Refer to the applicable instructions in AMM TASK 28-10-00-840-802 and remove
fuel fumes from tank(s).
CAUTION: KEEP A CONTINUOUS FLOW OF VENTILATING AIR THROUGH A
FUEL TANK WHEN WORK IS BEING DONE INSIDE THE TANK.
B. Procedure
NOTE: The Procedure section is divided into two parts. PART 1 gives the
instructions to rework the left side fuel tanks. PART 2 gives the
instructions to rework the right side fuel tanks.
Part 1 - Rework the Left Side Fuel Tank
(1) Refer to applicable instructions in AMM TASK 28-21-06-000-801 and Figure 2
and locate and remove the engine fuel feed lines that follow: (including related
cushion clamps and hardware). Keep related cushion clamps and related
hardware.
- 82822139-003 fuel feed line
- 82822140-001 fuel feed line
(2) Make sure to remove and discard the preformed O-rings from the fuel line
couplings.
(3) Make sure to put a cap on all open fuel lines. Route the removed fuel lines to
stores to determine disposition.
(4) Install new replacement bracket 85714430-003 to rib at station Y-136.300 in the
left fuel tank as follows:
(a) Refer to Figure 2 Flag Note 1 and locate and carefully remove and discard
one existing bracket from rib (p/n 85713370-001) at station Y-136.300.
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B,
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Refer to drawing 8Z6836, VIEW LOOKING RIB ASSY INBD AT Y-136.30 LH
and detail VIEW A and install new replacement bracket 85714430-003 to rib
at station Y-136.300 using two solid rivets B0205016AD5-7S.
(d) In a suitable area next to new bracket 85714430-003 re-identify rib
85713370-001 as 8Z6836-1 using an indelible marker.

### Page 14

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 12 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(5) Install new replacement bracket 85714527-001 to rib at station Y-157.825 in the
left fuel tank as follows:
(a) Refer to Figure 2 Flag Note 2 and at station Y-157.825 locate and carefully
remove and discard one existing bracket from rib (p/n 85713380-001).
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B,
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Refer to drawing 8Z6836, VIEW LOOKING RIB ASSY INBD AT Y157.825 LH
and detail VIEW C and install new replacement bracket 85714527-001 to
rib at station Y-157.825 using two solid rivets B0205016AD5-8S.
(d) In a suitable area next to new bracket 85714527-001 re-identify rib
85713380-001 as 8Z6836-3 using an indelible marker.
(6) Install / route the new fuel feed lines listed below to agree with all of the NOTES
and detail views given on drawing 8Z9209 ASSY VIEW -001. Secure the fuel feed
lines using previously removed clamps, screws and washers. Make sure to
install new preformed O-Rings MS29513-214 at each coupling B030508A16
during assembly.
- 82822139-005 fuel feed line
- 82822140-003 fuel feed line.
(7) Make sure that the fuel lines installed in the above steps have a minimum
clearance of no less that 0.125 inch from adjacent structure.
NOTE: If any discrepancy exists record the condition then contact the ‘‘Toronto
Help Desk at telephone number (416) 375-4000 or facsimile (416)
375-4539’’ or E-mail: thd.qseries@aero.bombardier.com for a corrective
action.
NOTE: Fuel lines designed with a protective Teflon sleeve installed around the
tube adjacent to wing structure are not required to achieve the minimum
clearance requirement given in the step above.
(8) Install and secure one Teflon hose DSC411-6-0026 and two clamps
B0305078-04 around tube assembly 82822065 (motive flow) at approx. station
Y-117.500 to agree with detail views gi ven on drawing 8Z9209 ASSY -001, detail
VIEW A and NOTES 7, 8 and 9.
(9) Install and secure one Teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent rib 85713802 at approx. station
Y-245.019 (refer to drawing 8Z9214, VIEW LOOKING DOWN, DETAIL A. and
NOTES 1 and 2).

### Page 15

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 13 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(10) Install and secure one Teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent rib 85713806 at approx. station
Y-317.019 (refer to drawing 8Z9214, VIEW LOOKING DOWN, DETAIL A. and
NOTES 1 and 2).
(11) Do a pressure test of the fuel feed lines (left side) to agree with applicable
instructions in AMM TASK 28-21-00-780-801.
(12) Refer to the Close Out section of this SB upon successful completion of the
pressure test (left side).
(13) Refer to PART 2 and rework the right side fuel tanks.
Part 2 - Rework The Right Side Fuel Tank
(1) Remove and discard cushion clamps and related hardware that secures existing
fuel feed line (p/n 82822143-001) to adjacent scavenge line at approx. Y-150.00
(refer to detail A on Figure 3).
(2) Locate and remove the engine fuel feed lines that follow: (including related
cushion clamps and hardware) (refer to applicable instructions in AMM TASK
28-21-06-000-801 and locations shown on Figure 3). Keep related cushion
clamps and hardware.
(3) Locate and remove the engine fuel feed lines that follow: (including related
cushion clamps and hardware) (refer to applicable instructions in AMM TASK
28-21-06-000-801 and locations shown on Figure 3). Keep related cushion
clamps and hardware.
- 82822142-003
- 82822143-001
- 82822144-001
(4) Make sure to put a cap on all open fuel lines. Route the removed fuel lines to
stores to determine disposition.
(5) Install new replacement bracket 85714428-003 to rib at station Y-136.300 in the
right side fuel tank as follows:
(a) Locate and carefully remove and discard one existing bracket from rib p/n
85713370-002 at station Y-136.300 (refer to Figure 3 Flag Note 1).
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Install new bracket 85714428-003 to rib p/n 85713370-002 at station
Y-136.300 using solid rivets B0205016AD5-7S (refer to drawing 8Z6836,
VIEW LOOKING RIB ASSY INBD AT Y-136.30 and detail VIEW B).

### Page 16

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 14 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(d) In a suitable area next to new bracket 85714428-003 re-identify rib
85713370-002 as 8Z6836-2 using an indelible marker.
(6) Install new replacement bracket 85714426-003 to rib at station Y-157.825 in the
right side fuel tank as follows:
(a) At station Y-157.825 locate and carefully remove and discard one existing
bracket from rib (p/n 85713380-002) (refer to Figure 3 Flag Note 2).
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Install new bracket 85714426-003 to rib at station Y-157.825 using two
solid rivets B0205016AD5-8S (refer to drawing 8Z6836 VIEW LOOKING RIB
ASSY INBD AT Y157.825 and detail VIEW D).
(d) In a suitable area next to new bracket 85714526-003 re-identify rib
85713380-002 as 8Z6836-4 using an indelible marker.
(7) Install / route the new fuel feed lines listed below to agree with all of the Notes
and detail views given on drawing 8Z 9209, ASSY VIEW -002. Secure the fuel
feed lines using previously removed clamps, screws and washers. Make sure to
use new O-Rings MS29513-214 at each co upling B030508A16 during assembly.
- 82822142-005 fuel feed line
- 82822143-003 fuel feed line
- 82822144-003 fuel feed line
(8) Make sure that fuel lines installed in the above steps have a minimum clearance
of no less that 0.125 inch from adjacent structure.
NOTE: Fuel lines designed with a protective Teflon sleeve installed around the
tube adjacent to wing structure are not required to achieve the minimum
clearance requirement given in the step above.
NOTE: If any discrepancy exists record the condition then contact the ‘‘Toronto
Help Desk at telephone number (416) 375-4000 or facsimile (416)
375-4539’’ or E-mail: thd.qseries@aero.bombardier.com for a corrective
action
(9) Install and secure one Teflon hose DSC411-6-0026 and two clamps
B0305078-04 around tube assembly 82822065 (motive flow) at approx. station
Y-117.500 to agree with detail views gi ven on drawing 8Z9209 ASSY -002, detail
VIEW A and NOTES 7, 8 and 9.
(10) Install and secure one Teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge tube assembly adjacent rib 85713802 at approx.
station Y-245.019 to agree with detail views given on drawing 8Z9214 VIEW A.
and NOTES 1 and 2.

### Page 17

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 15 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
(11) Install and secure one Teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent rib 85713806 at approx. station
Y-317.019 (refer to drawing 8Z9214, VIEW LOOKING DOWN, DETAIL A. and
NOTES 1 and 2).
(12) Do a pressure test of the fuel feed lines (right side) to agree with applicable
instructions in AMM TASK 28-21-00-780-801.
C. Close Out
(1) Make sure to remove all debris and unwanted material(s) from the fuel tanks.
(2) Install the left and/or right wing wet bay fuel tank access panels that follow, refer
to AMM TASK 57-11-01-400-801:
ACCESS DESIGNATION
523AT (and/or 623AT right wing) Wet Bay Fuel Access Panels
522BT (and/or 622BT right wing) Wet Bay Fuel Access Panels
522CT (and/or 622CT right wing) Wet Bay Fuel Access Panels
(3) Install the outer wing fuel access panels refer to AMM TASK 57-21-01-400-801.
ACCESS DESIGNATION
524CT (and/or 624CT right wing) Outer Wing Fuel Access Panels
524AT (and/or 624AT right wing) Outer Wing Fuel Access Panels
(4) Remove all tools and equipment from the work area.
(5) On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applic able logbook(s). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.

### Page 18

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 16 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
Removal and Installation of Fuel Access Panels
Figure 1
LH SIDE SHOWN, RH SIDE OPPOSITE
EXCEPT AS NOTED
523AT (LHS)
623AT (RHS)
522CT (LHS)
622CT (RHS)
524AT (LHS)
624AT (RHS)
524CT (LHS)
624CT (RHS)
YW - -42.000
522BT (LHS)
622BT (RHS)

### Page 19

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 17 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
Existing Clipping & Fuel feed Lines - Removal Left Side Fuel Tanks
Figure 2
AC
CL
82822139-003
ENG FUEL FEED LINE
REMOVE EXISTING
82822140-001
ENG FUEL FEED LINE
REMOVE EXISTING
REMOVE EXISTING BRACKET.
INSTALL NEW BRACKETS AT SAME LOCATION
1
NOTES:
RIB
85713370-001
2
1 2
85713380-001
RIB
Y- -42.00
Y- -117.500
Y- -136.300
Y- -157.820
Y- -191.200
LEFT WING TOP VIEW SHOWN.
REAR SPAR

### Page 20

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 18 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
Existing Clipping & Fuel feed Lines - Removal Right Side Fuel Tanks
Figure 3
Y-173.200
Y-157.825
Y-136.300
Y-25.258
ENG FUEL FEED LINE
REMOVE EXISTING
82822143-001
ENG FUEL FEED LINE
REMOVE EXISTING
82822144-001
ENG FUEL FEED LINE
REMOVE EXISTING
82822142-003
Y-117.500
1 2
NOTES:
1 2 REMOVE EXISTING BRACKET.INSTALL NEW BRACKETS AT SAME LOCATION
RIB
85713370-001 RIB85713380-002EXISTING CLIPPING
EXISTING FUEL FEED LINE
EXISTING SCAVENGE LINE
RIGHT WING TOP VIEW SHOWN.
REMOVE AND DISCARD

### Page 21

SERVICE BULLETIN 84-28-09
S.B. 84-28-09
Page 19 of 19
22 June 2010
Revision ‘D’ 29 Jan 2013 MG
This Page Intentionally Blank
1

### Page 22

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 23

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
