# Bombardier Service Bulletin 84-28-12

Copy: Revision A ("U.S. DOT/FAA - SB 84-28-12A"), 24 pages: PDF https://openairdocs.org/files/sha256/01/f6/01f617a6532d579fc00c8a252d76e8109ab2fb640dc0faeadc4f96713a6ea876; text https://openairdocs.org/service-documents/bombardier/sb-84-28-12/file/01f617a6532d.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0146; AD 2015-02-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-28-12
- Latest revision known: 84-28-12, Revision A, dated June 20, 2013 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-28-12

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-02-25](https://openairdocs.org/ad/2015-02-25.md), effective Mar 17, 2015: Revision A

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-28-12/proposed.md).

## Text (24 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0146; AD 2015-02-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘A’ 20 Jun 2013
DHC-8 (DASH 8)
SERVICE BULLETIN 84-28-12
Fuel - Fuel Tank System Design Left and Right Side (SFAR 88) -
Replacement of Fitting p/n 82822074-951 - ModSum 4-126537
This page transmits Revision ‘A’ of Service Bulletin 84-28-12, pages 1 thru
20, dated 20 Jun 2013.
This service bulletin is re-issued in its entirety for the reasons that follow:
- the References section is revised to convey the latest revision of the service
bulletin
- the Parts Required Per Aircraft section is revised to add a NOTE in step (2)
that indicates acceptable alternatives for the consumable materials
- step 3.B.(6) in the Accomplishment Instructions section is revised to change
“view A-A” to “view C-C” and to delete the text “51-80-00-760-801” at the end
of the step.
The Compliance in the previous issue(s) of this service bulletin is not
affected by this revision. No additional rework to the aircraft is introduced by
this revision.
Remove the initial issue of Service Bulletin 84-28-12 and replace with
attached.
Previous issue(s) of Service Bulletin 84-28-12:
Initial issue - Pages 1 thru 20 dated 23 Jul 2012

### Page 2

(No text on this page.)

### Page 3

D
S.B. 84-28-12
Page 1 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2810 NUMBER: 84-28-12
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fuel - Fuel Tank System Design Left and Right Side (SFAR 88) -
Replacement of Fitting p/n 82822074-951 - ModSum 4-126537
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4063 thru
4118.
NOTE: The instructions in this Service Bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None

### Page 4

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 2 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
B. Reason
This service bulletin is issued as a result of FAA certification requirement
Special Federal Aviation Regulation 88 (SFAR 88) to enhance fuel tank
system safety.
Problem: An operator of a DHC 8 Q400 aircraft has reported finding a fitting p/n
82822074-951 installed through the rear spar (left and right side at station
X-76.829) instead of fitting 82822074-007 or 82822074-005. The issue was
discovered during incorporation of SB 84-57-09 (ModSum 4-126330).
Fitting p/n 82822074-951 (installed by ModSum 4Y121542 and
82822074NIEO273101) does not comply with FAA certification
requirements given in the SFAR 88 regulations.
Solution: This service bulletin introduces ModSum 4-126537.
The ModSum replaces existing fittings p/n 82822074-951 with new fittings
p/n 82822074-009.
The new fittings are designed to enhance fuel tank system safety and
comply with SFAR 88 requirements.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- lock pins are installed thru each main gear and main gear door mechanism
- the nose gear ground lock is engaged
- affected left and/or right side fuel tank is defueled as required
- all aircraft electrical power is selected to the OFF position
- electrically grounded work platforms or ladders are set-up around and/or under the
left (and/or right) wing rear spar at approx. stn Y102D X-76.829
- left and/or right side fuel tank access panels are removed for access
- on the rear spar (left and right hand side) the refuel control solenoid valve is located
and removed from fitting p/n 82822074-951
- existing fitting(s) p/n 82822074-951 and related shroud, gasket and o-rings are
removed. The shroud is kept and remaining items are discarded

### Page 5

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 3 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
- protective finish is removed from certain areas of the rear spar. The reworked areas
are treated with Alodine 1132
- new fittings p/n 82822074-009, o-rings and kept shrouds are installed
- an electrical bonding test from fitting 82822074 -009 to adjacent aircraft structure is
done
- the fitting assembly 82822074-009 is sealed using DHMS S3.01 sealant to the rear
spar
- an operational test of the level control shutoff valve is done
- Close-Out
D. Compliance
Bombardier Inc. recommends that ModSum 4-126537 be incorporated at the
earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
An Airworthiness Directive from Transport Canada is pending.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
F. Manpower
It will take an estimated 8.50 man-hours to complete this Service Bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up *2.00
Procedure *4.00
Test / RTS 0.50
Close-Out 2.00

### Page 6

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 4 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
*T ime to defuel aircraft and cure times of sealant not included.
NOTE: Many MAN-HOURS would be saved if this SB is accomplished
concurrently with SB 84-57-09.
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the
Q Series Technical Help Desk by telephone at 416-375-4000 or
email at : thd.qseries@aero.bombardier.com
G. Material - Price and Availability
The part(s) detailed in Paragraph(s) 2.A. may be obtained from any Bombardier
Aerospace Regional Aircraft authorized parts source. The price and availability will
be quoted at the time of order.
H. Tooling - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Maintenance Manual PSM 1-84-2................................
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................

### Page 7

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 5 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
L. References
Revision ‘A’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4626 1 -
8Z9626 1 -
ModSum 4Q126537 Rev. ‘B’
ModSum 4-126537 Rev. ‘B’
ModSum 4-126330 Rev. ‘E’ (SB 84-57-09)
PCA 40933 issue 3 (for internal reference only)
Transport Canada Airworthiness Directive Pending
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Detailed Parts List for 8MK4626-001:
Quantity
Per Aircraft
Part Number Description Remarks
4 MS29513-020 O-Ring
2 MS29513-014 O-Ring
2 MS29513-013 O-Ring
2 MS29512-08 O-Ring
2 82822032-101 Gasket
2 82822074-009 Fitting Assembly
NOTE: This service bulletin is self-contained (illustrated). No drawings will be
supplied.

### Page 8

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 6 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
(2) In addition to the above part(s), the following material(s) are required for
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in
either Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter
51 or, for 400 Series Aircraft, in Consumable Products Manual PSM 1-84-18.
Part Number Qty. Per Aircraft Description Remarks
07-29A 1T u b e Alodine 1132 Touch-N Prep Pen
(592939)
06-01A 2C a r t r i d g e s Sealant Class B
Type II (DHMS
S3.01)
Temperature-Resist-
ant Integral Fuel-
Tanks
04-14 AR Petroleum Jelly ¾
Petrolatum
B0816019-003. 2 Tiedown strap
MS20995C32 A/R Lock Wire
NOTE: Refer to CPM PSM 1-84-18 for the list of approved consumable products
under each Product ID No., any of which can be used unless a note
states otherwise.
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None

### Page 9

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 7 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non-indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
------- O-Ring 4 D DIS MS29513-020 S
------- O-Ring 2 D DIS MS29513-014 S
------- O-Ring 2 D DIS MS29513-013 S
O-Ring 2 D DIS MS29512-08 S
------- Gasket 2 D DIS 82822032-101 S
82822074-951 Fitting
Assembly
2 C DIS 82822074-009 X
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
D Existing p/n number and new p/n are the same
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.

### Page 10

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 8 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate on
part that this service bulletin has been accomplished.
R Part number after rework.
S Existing p/n number and new p/n are the same
X The old part and the new part are similar in appearance but only the new part
is SFAR 88 compliant.
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
The procedure that follows gives the instructions to replace existing fitting
82822074-951. The existing fitting is part of the refuel control solenoid valve assembly
and is installed through the left & right side rear spar at approx. stn Y102D X-76.829.
The instructions to replace an existing fitting 82822074-951 in the left side rear spar are
given. The instructions to replace an existi ng fitting in the right side rear spar are the
same.
WARNING: OBEY ALL THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK
ON THE FUEL SYSTEM AND/OR A FUEL SYSTEM COMPONENT. IF
YOU DO NOT YOU CAN CAUSE INJURIES TO PERSONS AND/OR
DAMAGE TO EQUIPMENT.
(1) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(2) Make sure the nose gear ground lock is engaged.
(3) Connect ground hydraulic power to the number 1 system (refer to AMM TASK
12-00-16-490-801). Set the pressure to 3000 psi (20684 kPa) and a flow rate of
2.5 gal/min. (9.5 L/min.).
WARNING: MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT ON OR
NEAR THE FLAPS OR ANY OTHER FLIGHT CONTROL. ACCIDENTAL
MOVEMENT OF THE FLIGHT CONTROLS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.

### Page 11

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 9 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
(4) Make sure the area around each flap is clear then lower flaps to the 35 ˚ position.
(5) Remove the ground hydraulic power (refer to AMM TASK 12-00-16-090-801).
(6) Pressure defuel the aircraft (refer to AMM TASK 12-10-28-650-802).
(7) Make sure to de-energize the aircraft electrical system (refer to AMM TASK
24-00-00-861-802).
(8) Set up work platforms or ladders around and/or under the left (and/or right) wing
to permit access to the refuel control sole noid valve on rear spar (at approx. stn
Y102D X-76.829) and wing fuel access pane l 522AT (622AT right side) (refer to
TASK 06-41-00-992-808 for access panel location). Make sure that the work
platforms or ladders are electrically grounded (refer to Figure 1).
(9) Make sure to obey the fuel system safety precautions (refer to AMM TASK
28-00-00-910-801).
(10) Obey the electrical/electronic safety precautions (refer to AMM TASK
24-00-00-910-801).
(11) Obey the electrostatic discharge safety precautions (refer to AMM TASK
24-00-00-910-802).
CAUTION: M A K ES U R EA L LF U E LI SD R A I N E DF R O MT H EF U E LT A N KB E F O R E
YOU REMOVE FUEL TANK ACCESS PANELS. IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE WING STRUCTURE.
(12) Drain remaining fuel from the applicable fuel tank using the water drains (refer to
AMM TASK 28-11-00-680-801).
(13) Remove the left (and/or right side) wing fuel access panel that follow using
applicable instructions in AMM TASK 57-11-01-000-801.
ACCESS DESIGNATION
522AT (and/or 622AT right wing) Wet Bay Fuel Access Panels
(14) Remove the fuel fumes from the fuel tank (refer to AMM TASK
28-10-00-840-802).

### Page 12

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 10 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
(15) Remove the inboard flap closure panel that follows (refer to applicable
instructions in AMM TASK 57-51-01-000-801).
ACCESS DESIGNATION
531AB Flap Closure Panel (left side)
631AB Flap Closure Panel (right side)
B. Procedure
(1) Gain access to the refuel control solenoid valve located on the aft side of the
rear spar at approx. stn Y102D X-76.829 (refer to Figure 1 Sheets 1, 2 & 3).
(2) Remove and retain the refuel control solenoid valve from existing fitting using
applicable instructions in AMM TASK 28-23-11-000-801. Make sure to discard
the existing o-rings.
(3) Remove the parts that follow (refer to Figure 2 & 3):
- shroud 82822077-005 (make sure to disconnect the drain line from the shroud
prior to removal)
- fitting 82822074-951 (discard)
- gasket 82822032-101 (discard)
- o-rings MS29512-08, MS29513-013, MS29513-014 and MS29513-020 (discard)
(4) Remove protective finish from the mating surface on the aft side of the rear spar
(dry side) to agree with applicable instructions given in the SRM PSM 1-84-3
51-26-10-02-01. The four rework areas are indicated with hash marks on the aft
side of the rear spar shown on Figure 5 VIEW E-E.
(5) Touch-up the reworked areas on the rear spar with a layer of alodine 1132 (refer
to applicable instructions in SRM 51-21-10-02-02. Make sure to allow alodine to
dry.

### Page 13

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 11 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
(6) Install the new parts that follow to agree with the detail views given on Figure 2
SECTION view C-C. Make sure to lubricate the o-rings with petrolatum before
installation.
- gasket 82822032-101
- fitting 82822074-009
- shroud 82822077-005
- new o-rings MS29512-08, MS29513-013, MS29513-014 and MS29513-020.
(7) Re-attach the drain line to the shroud and secure with a tiedown strap p/n
B0816019-003.
(8) Install the refuel control solenoid valve (previously removed) to fitting
82822074-009 (refer to Figure 2 and applicable instructions in AMM TASK
28-23-11-400-801).
Make sure to install lockwire from solenoid valve to one of the bolts on the fitting
(refer Figure 4 and applicable instructions in AMM TASK 20-10-30-400-801).
(9) Re-Identify installation as 8Z9626-001 (refer to applicable instructions in AMM
TASK 20-00-01-910-801).
(10) Do an electrical bonding test from fitting 82822074-009 to aircraft structure.
Reading to be less than 20 milliohms (see Flagnote 2 on Figure 2 and refer
to SRM TASK 51-80-00-02-01).
(11) Connect the electrical connector to the refuel control solenoid valve.
(12) Make sure to fillet profile seal fitting assembly 82822074-009 and aft face of rear
spar at location depicted (see Flagnote 1 on Figure 2) refer to applicable
instructions in SRM PSM 1-84-3 Chapter 51-23-20-02-01.

### Page 14

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 12 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
C. Close Out
(1) Install the left (and/or right side) wing access panels that follow (refer to
applicable instructions in AMM TASK 57-11-01-400-801.
ACCESS DESIGNATION
522AT (and/or 622AT right wing) Wet Bay Fuel Access Panels
(2) Do an operational test of the level control shutoff valve (refer to AMM TASK
28-24-00-710-802).
(3) Do a visual check for any signs of leakage at the rework site. Rectify as
required.
(4) Install the inboard flap closure panels that follows (refer to applicable
instructions in AMM TASK 57-51-01-400-801).
ACCESS DESIGNATION
531AB Flap Closure Panel (left side)
631AB Flap Closure Panel (right side)
(5) Remove all tools, equipment and unwanted materials from the work area.
(6) On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applic able logbook(s). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.

### Page 15

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 13 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Locator View
Figure 1 Sheet 1

### Page 16

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 14 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Locator View
Figure 1 Sheet 2

### Page 17

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 15 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Locator View
Figure 1 Sheet 3
VIEW LOOKING FWD
ON REAR SPAR
FUEL TANK ACCESS
PANEL 522AT (622AT)

### Page 18

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 16 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Figure 2
MS29512-08
O-RING
O-RING
MS29513-020
O-RING
MS29513-014
O-RING
MS29513-013
FITTING
WAS 82822074-951
NOW 82822074-009
GASKET
82822032-101
SHROUD
82822077-005
REFUEL CONTROL
D
D
DRAIN LINE
TIEDOWN STRAP
B0816019-003
ELECTRICAL BONDING BY DIRECT CONTACT
P E RS R MC H A P T E R5 1 - 8 0 - 0 0 - 0 2 - 0 12
NOTES:
FILLET PROFILE SEAL WITH DHMS S3.01
CLASS B TYPE II SEALANT PER SRM
51-23-20-02-01
1
2
REAR SIDE OF REAR SPAR
Fitting & Solenoid Valve - Installation
FOR O-RING INSTLN
DETAILS SEE FIGURE 3

### Page 19

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 17 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
O-Ring & Gasket - Location
Figure 3
O-RING
MS29513-013
O-RING
MS29513-020
O-RING
MS29513-014
MS29512-08
O-RING
GASKET
82822032-101

### Page 20

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 18 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Figure 4
Rework Location - VIEW D-D
NOTES:
FITTING ASSEMBLY
82822074-009
LOCK WIRE
MS20995C32

### Page 21

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 19 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
Figure 5
VIEW E-E
Rework Location - VIEW E-E

### Page 22

SERVICE BULLETIN 84-28-12
S.B. 84-28-12
Page 20 of 20
23 Jul 2012
NB
Rev. ‘A’ 20 Jun 2013
This Page Intentionally Blank
1

### Page 23

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 24

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
