# Bombardier Service Bulletin 84-28-13

Copy: No revision named ("SB 84-28-13"), 12 pages: PDF https://openairdocs.org/files/sha256/fa/1b/fa1b423a33e8a88d3c139415f661b529e918c1cf7d46fe369a0f2d63f5e7a5df; text https://openairdocs.org/service-documents/bombardier/sb-84-28-13/file/fa1b423a33e8.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-28-13
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-28-13

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-17-25](https://openairdocs.org/ad/2015-17-25.md), effective Oct 7, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-28-13/proposed.md).

## Text (12 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

D
S.B. 84-28-13
Page 1 of 10
17 Aug 2012
MG
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2812 NUMBER: 84-28-13
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fuel System - Center Wing - Removal of Clamps Between Engine
Feed and Scavenge System Lines on RHS - ModSum 4-113745
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4332 thru
4417.
NOTE: Serial Numbers 4001 thru 4331 are covered by Bombardier Service
Bulletin 84-28-09 (ModSum 4-113643).
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None

### Page 2

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 2 of 10
17 Aug 2012
MG
B. Reason
Problem: The existing clamp installation in the right hand side center wing fuel tank
(between the engine fuel feed line and the scavenge system line) is now
redundant after the engine fuel feed line revision that increased the space
between the two lines.
Solution: Remove and discard the existing clamp installation located between the
engine fuel feed line and the scavenge system line.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- the fuel tanks are drained, aircraft electrical power is removed and the engines are
supported
- access is gained to fuel tank access panel 622CT-right hand side
- access panel 622CT is removed, residual fuel is mopped up and the tank is vented
- the affected clamps and hardware are removed and discarded
- access panel 622CT-right hand side is installed
- close out.
D. Compliance
Bombardier Inc. highly recommend that ModSum 4-113745 be incorporated at the
earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
A Transport Canada Airworthiness Directive Pending.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.

### Page 3

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 3 of 10
17 Aug 2012
MG
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
F. Manpower
It will take an estimated 2.50 man-hours to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up *1.00
Procedure 0.50
Test / RTS not applicable
Close-Out 1.00
* time required to defuel and vent fuel tank not included
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com
G. Material - Price and Availability
The part(s) and material(s) detailed in Paragraph(s) 2.A. may be purchased as
single items from Bombardier Aerospace Regional Aircraft. DK parts are to be
manufactured and approved locally (refer to disclaimer in the related text or
illustration). In some cases, an equivalent to the DK part may be available from
Bombardier under the production part number shown as reference in Parts
Required Per Aircraft.
H. Tooling - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected

### Page 4

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 4 of 10
17 Aug 2012
MG
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
L. References
The initial issue of this service bulletin was prepared to the engineering drawings
and related data that follows:
DRAWING SHEET REV
8DK4195 1 -
ModSum 4Q113745 Rev. ‘B’
ModSum 4-113745 Rev. ‘B’
Bombardier Service Bulletin 84-28-09 Rev. ‘C’ (ModSum 4-113643)
Bombardier Service Bulletin 84-28-14 (ModSum 4-113754)
Bombardier Service Bulletin 84-28-15 (ModSum 4-113762)
PCA 44006 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive Pending.
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Drawing Kit 8DK4195-001, Rework - Fuel System Installation, Center Wing
(2) Detailed Kit Content:
Quantity Per Kit
-001
Part Number Description Remarks
1 -001 Rework drawing

### Page 5

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 5 of 10
17 Aug 2012
MG
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALLY
RETRACT. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE
TO THE EQUIPMENT.
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE LANDING GEAR
DOORS. MAKE SURE YOU DISCONNECT THE LANDING GEAR
DOORS. IF YOU DO NOT DO THIS THE LANDING GEAR DOORS WILL
CLOSE WHEN YOU APPLY THE HYDRAULIC PRESSURE. THIS CAN
CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.
WARNING: OBEY ALL THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK
ON THE FUEL SYSTEM AND/OR A FUEL SYSTEM COMPONENT. IF
YOU DO NOT YOU CAN CAUSE INJURIES TO PERSONS AND/OR
DAMAGE TO EQUIPMENT.
(1) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(2) Make sure the nose gear ground lock is engaged.
WARNING: YOU MUST REMOVE THE FUEL FROM THE FUEL TANK IN AN OPEN
AREA. IF YOU DO NOT DO THIS, YOU CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.

### Page 6

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 6 of 10
17 Aug 2012
MG
(3) Refer to AMM TASK 28-10-00-840-801 and prepare fuel tank for access. Make
sure no fuel or fuel vapors are present before working on aircraft or in the fuel
tanks.
(4) Refer to AMM TASK’ 24-00-00-861-802, TASK 24-00-00-910-801 and placard and
select all aircraft electrical power to OFF. Obey all relevant WARNINGS and
CAUTIONS.
(5) Refer to Figure 1 and set up work platforms and/or ladders to permit access to
the fuel tank access panel 622CT right hand side. Make sure that the work
platforms or ladders are electrically grounded.
(6) Refer to AMM TASK 28-00-00-910-801 and make sure to obey the fuel system
safety precautions.
(7) Refer to AMM TASK 24-00-00-910-801 and make sure to obey the
electrical/electronic safety precautions.
(8) Refer to AMM TASK 24-00-00-910-802 and obey the electrostatic discharge
safety precautions.
CAUTION: MAKE SURE THAT THE FUEL TANKS ARE DRAINED BEFORE YOU
REMOVE THE ACCESS PANELS. IF YOU DO NOT DO THIS, YOU CAN
CAUSE DAMAGE TO THE WING STRUCTURE.
CAUTION: MAKE SURE THAT YOU DO NOT MOVE THE AIRCRAFT BEFORE YOU
INSTALL THE FUEL ACCESS PANELS. THIS IS NECESSARY TO
PREVENT DAMAGE TO THE WING AND THE WING BOX STRUCTURE.
(9) Refer to Figure 1 and the applicable instructions in AMM TASK 57-11-01-000-801
and remove right wing access panel 622CT.
(10) Use cotton cloths or a natural sponge to soak up the remaining fuel.
(11) Refer to the applicable instructions in AMM TASK 28-10-00-840-802 and remove
fuel fumes from tank.
CAUTION: KEEP A CONTINUOUS FLOW OF VENTILATING AIR THROUGH A
FUEL TANK WHEN WORK IS BEING DONE INSIDE THE TANK.
B. Procedure
(1) Refer to Figure 2 and locate existing clamp installation between Y136.300 and
Y157.825.

### Page 7

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 7 of 10
17 Aug 2012
MG
(2) Remove and discard screw NAS1801-3-16, spacer NAS43DD3-32FC, clamp
MS21919WDF12, clamp MS21919WDF16, was her AN960D10L and self locking
nut MS21042L3.
C. Close Out
(1) Make sure to remove all debris and unwanted material(s) from the fuel tanks.
(2) Refer to AMM TASK 57-11-01-400-801 and install right wing access panel
622CT.
(3) Remove all tools and equipment from the work area.
(4) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 8

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 8 of 10
17 Aug 2012
MG
Plan View
Figure 1

### Page 9

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 9 of 10
17 Aug 2012
MG
Detail A
Figure 2
REMOVED AND DISCARDED:
SCREW NAS1801-3-16
SPACER NAS43DD3-32FC
CLAMP MS21919WDF12
CLAMP MS21919WDF16
WASHER AN960D10L
NUT, SELF LOCKING
MS21042L3
ENGINE FEED INSTALLATION
82822002
SCAVENGE MOTIVE
FLOW INSTALLA-
TION
82822012

### Page 10

SERVICE BULLETIN 84-28-13
S.B. 84-28-13
Page 10 of 10
17 Aug 2012
MG
This Page Intentionally Blank
1

### Page 11

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 12

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
