# Bombardier Service Bulletin 84-28-15

Copy: No revision named ("SB 84-28-15"), 20 pages: PDF https://openairdocs.org/files/sha256/eb/d4/ebd4992754a82536f9f501a6fcff516710122bc2b9ea4bd5be6413791117f60e; text https://openairdocs.org/service-documents/bombardier/sb-84-28-15/file/ebd4992754a8.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-28-15
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-28-15

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-17-25](https://openairdocs.org/ad/2015-17-25.md), effective Oct 7, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-28-15/proposed.md).

## Text (20 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0583; AD 2015-17-25 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

D
S.B. 84-28-15
Page 1 of 18
17 Aug 2012
MG
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 2812 NUMBER: 84-28-15
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fuel System - Center Wing - Engine Fuel Feed Installation - Introduction of
New Tube to Eliminate Fouli ng Condition - ModSum 4-113762
1. PLANNING INFORMATION
NOTE: This service bulletin supercedes Bombardier Service Bulletin 84-28-09 for
operators who have not ordered ModKit 8MK4429-001.
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003, 4004, 4006, 4008 thru 4417.
Production: ModSum 4-113762 will be installed before delivery on
applicable DHC-8 Aircraft Models 401 and 402 at Serial
Number 4418 and subsequent.
Spares Affected:
None

### Page 2

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 2 of 18
17 Aug 2012
MG
B. Reason
Problem: Operators have reported a fouling condition between engine fuel feed line
82822143-003 and the wing structure at station Y-157.825 (right side fuel
tank).
Other locations have been reported with inadequate clearance between
the fuel pipe and structure. In the event of a lightning strike, a spark could
be produced at the fouling interface between pipe and structure.
Solution: This service bulletin introduces ModSum 4-113762 which replaces five
existing fuel lines (two in the left wing and three in the right wing and
supporting brackets) with new fuel lines and supporting brackets.
The new fuel lines and brackets are designed to include different
geometric angles to make sure contact with the wing structure is
eliminated and adequate clearance is maintained. In addition, teflon
tubing is wrapped around one motive flow line and scavenge lines in each
fuel tank (left and right side) at specific locations as part of the modification.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- aircraft is put into standard configuration for maintenance
- aircraft electrical power is removed
- the nose landing gear lock is engaged
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- the fuel tanks are drained
- the engines are supported then specific fu el tank access panels (center and outer
wing) are removed
- r e s i d u a lf u e li sm o p p e du pa n dt h et a n ki sv e n t e d
- five existing fuel feed tube assemblies, four existing brackets, cushion clamps and
related hardware are removed
- five new fuel feed lines and new brackets are installed and secured using kept
hardware
- the reworked ribs in each wing are re-identified with a new part number
- teflon sleeves are installed around a motive fuel line in each outer wing tank
- the new lines are pressure tested

### Page 3

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 3 of 18
17 Aug 2012
MG
- close out.
D. Compliance
Bombardier Inc. highly recommend that ModSum 4-113762 be incorporated at the
earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
Transport Canada Airworthiness Directive Pending.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
F. Manpower
It will take an estimated 35.00 man-hour s to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS MAN-HOURS TO
RWK LEFT WING
MAN-HOURS TO
RWK RIGHT WING
Job Set-Up *2.00 n/a n/a
Procedure /Test/
RTS
n/a 14.00 15.00
Close-Out **4.00 n/a n/a
* time required to defuel and vent fuel tank not included
** cure time for sealant not included.
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com
G. Material - Price and Availability
ModKit 8MK4497-001 is available through the Customer Accounts Service Team at

### Page 4

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 4 of 18
17 Aug 2012
MG
Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial number(s) to:
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920
Kit Number Description
8MK4497-001 Retrofit Kit - Engine Fuel Feed Line
H. Tooling - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Maintenance Manual PSM 1-84-2................................
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
L. References
The initial issue of this service bulletin was prepared to the engineering drawings
and related data that follows:
DRAWING SHEET REV

### Page 5

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 5 of 18
17 Aug 2012
MG
DRAWING REV SHEET
8MK4497 1 -
8Z9214 1 -
8Z9609 1 -
8Z6836 1 A
ModSum 4Q113762 Rev. ‘B’
ModSum 4-113762 Rev. ‘B’
Bombardier Service Bulletin 84-28-09 (ModSum 4-113643)
Bombardier Service Bulletin 84-28-13 (ModSum 4-113745)
Bombardier Service Bulletin 84-28-14 (ModSum 4-113754)
PCA 44006 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive Pending.
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4497-001, Retrofit Kit - Engine Fuel Feed Line
(2) Detailed Kit Content:
Quantity Per Kit
-001
Part Number Description Remarks
1 8Z9214 Retrofit drawing
1 8Z9609 Retrofit drawing
1 8Z6836 Structural Provisions drawing
1 8Z6836-001 Rework-Structural Provisions
1 82822139-005 Tube Assembly
1 82822140-003 Tube Assembly

### Page 6

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 6 of 18
17 Aug 2012
MG
Quantity Per Kit
-001
RemarksDescriptionPart Number
1 82822142-005 Tube Assembly
1 82822143-003 Tube Assembly
1 82822144-005 Tube Assembly
12 MS29513-214 Packing, O-Ring
2 MS29513-215 Packing, O-Ring
4 DSC411-12-0032 Teflon Hose
2 DSC411-6-0026 Teflon Hose
4 B0305078-10 Clamp
4 B0305078-04 Clamp
(3) In addition to the above part(s), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in
either Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter
51 or, for 400 Series Aircraft, in Consumable Products Manual PSM 1-84-18.
Part Number Qty. Per
Aircraft
Description Remarks
DHMS C4.06 10 oz. Coating, Corrosion Preventative
for Aircraft Integral Fuel Tanks
Type 1, Class A,
Grade A or Grade B,
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are

### Page 7

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 7 of 18
17 Aug 2012
MG
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non-indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
82822139-003 Tube Assy Eng Feed
(LH side)
1 A SAL 82822139-005 S
82822140-001 Tube Assy Eng Feed
(LH side)
1 A SAL 82822140-003 S
82822142-003 Tube Assy Eng Feed
(RH side)
1 A SAL 82822142-005 S
82822143-001 Tube Assy Eng Feed
(RH side)
1 A SAL 82822143-003 S
82822144-001 Tube Assy Eng Feed
(RH side)
1 A SAL 82822144-005 S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate on
part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.

### Page 8

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 8 of 18
17 Aug 2012
MG
3. ACCOMPLISHMENT INSTRUCTIONS
NOTE: The operator has the option of reworking the left side and right side fuel
tanks at different times or reworking bo th left side and right side fuel tanks
at the same time.
A. Job Set-Up
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALLY
RETRACT. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE
TO THE EQUIPMENT.
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE LANDING GEAR
DOORS. MAKE SURE YOU DISCONNECT THE LANDING GEAR
DOORS. IF YOU DO NOT DO THIS THE LANDING GEAR DOORS WILL
CLOSE WHEN YOU APPLY THE HYDRAULIC PRESSURE. THIS CAN
CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.
WARNING: OBEY ALL THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK
ON THE FUEL SYSTEM AND/OR A FUEL SYSTEM COMPONENT. IF
YOU DO NOT YOU CAN CAUSE INJURIES TO PERSONS AND/OR
DAMAGE TO EQUIPMENT.
(1) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(2) Make sure the nose gear ground lock is engaged.
WARNING: YOU MUST REMOVE THE FUEL FROM THE FUEL TANK IN AN OPEN
AREA. IF YOU DO NOT DO THIS, YOU CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.
(3) Refer to AMM TASK 28-10-00-840-801 and prepare fuel tank for access. Make
sure fuel or fuel vapors are not present before working on aircraft or in the fuel
tanks.

### Page 9

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 9 of 18
17 Aug 2012
MG
(4) Refer to AMM TASK’ 24-00-00-861-802, TASK 24-00-00-910-801 and placard and
select all aircraft electrical power to OFF. Obey all relevant WARNINGS and
CAUTIONS.
(5) Set up work platforms and/or ladders to permit access to the fuel tank access
panels between wing stations Y-42.000 and Y-317.019 left and right side wing.
Make sure that the work platforms or ladders are electrically grounded.
(6) Refer to AMM TASK 28-00-00-910-801 and make sure to obey the fuel system
safety precautions.
(7) Refer to AMM TASK 24-00-00-910-801 and make sure to obey the
electrical/electronic safety precautions.
(8) Refer to AMM TASK 24-00-00-910-802 and obey the electrostatic discharge
safety precautions.
CAUTION: MAKE SURE THAT THE FUEL TANKS ARE DRAINED BEFORE YOU
REMOVE THE ACCESS PANELS. IF YOU DO NOT DO THIS, YOU CAN
CAUSE DAMAGE TO THE WING STRUCTURE.
CAUTION: MAKE SURE THAT YOU DO NOT MOVE THE AIRCRAFT BEFORE YOU
INSTALL THE FUEL ACCESS PANELS. THIS IS NECESSARY TO
PREVENT DAMAGE TO THE WING AND THE WING BOX STRUCTURE.
(9) Refer to Figure 1, the applicable instructions in AMM TASK 57-11-01-000-801
and the table below and remove the left and/or right wing wet bay fuel tank
access panels.
ACCESS DESIGNATION
523AT (left wing) and/or 623AT (right wing) Wet Bay Fuel Access Panels
522BT (left wing) and/or 622BT (right wing) Wet Bay Fuel Access Panels
522CT (left wing) and/or 622CT (right wing) Wet Bay Fuel Access Panels
(10) Refer to Figure 1, the applicable instructions in AMM TASK 57-21-01-000-801
and the table below and remove the outer wing fuel tank access panels.
ACCESS DESIGNATION
524AT (left wing) and/or 624AT (right wing) Outer Wing Fuel Access Panels
524CT (left wing) and/or 624CT (right wing) Outer Wing Fuel Access Panels

### Page 10

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 10 of 18
17 Aug 2012
MG
(11) Use cotton cloths or a natural sponge to soak up the remaining fuel.
(12) Refer to the applicable instructions in AMM TASK 28-10-00-840-802 and remove
fuel fumes from tank(s).
CAUTION: KEEP A CONTINUOUS FLOW OF VENTILATING AIR THROUGH A
FUEL TANK WHEN WORK IS BEING DONE INSIDE THE TANK.
B. Procedure
NOTE: The Procedure section is divided into two parts. PART 1 gives the
instructions to rework the left side fuel tanks. PART 2 gives the
instructions to rework the right side fuel tanks.
Part 1 - Rework of the Left Side Fuel Tank
(1) Refer to applicable instructions in AMM TASK 28-21-06-000-801 and Figure 3
and locate and remove engine fuel feed line 82822139-003 and 82822140-001
(including related cushion clamps and h ardware). Keep related cushion clamps
and related hardware.
(2) Remove and discard the preformed O-rings from the fuel line couplings.
(3) Cap all open fuel lines. Send the removed fuel lines to stores to determine
disposition.
(4) Install new replacement bracket 85714430-003 to rib at station Y-136.300 in the
left fuel tank as follows:
(a) Refer to Figure 3-Flag Note 1 and locate, carefully remove and discard one
existing bracket from rib 85713370-001 at station Y-136.300.
(a) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B,
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(b) Refer to drawing 8Z6836, VIEW LOOKING RIB ASSY INBD AT
Y102D-Y136.30 LH and VIEW A and install new replacement bracket
85714430-003 to rib at station Y-136.300 using two solid rivets
B0205016AD5-7S.
(c) In a suitable area next to new bracket 85714430-003 re-identify rib
85713370-001 as 8Z6836-1 using an indelible marker.

### Page 11

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 11 of 18
17 Aug 2012
MG
(5) Install new replacement bracket 85714527-001 to rib at station Y-157.825 in the
left fuel tank as follows:
(a) Refer to Figure 3-Flag Note 2 and at station Y-157.825 locate, carefully
remove and discard one existing bracket from rib 85713380-001.
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B,
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Refer to drawing 8Z6836, VIEW LOOKING RIB ASSY INBD AT
Y102D-Y157.825 LH and VIEW C and install new replacement bracket
85714527-001 to rib at station Y-157.825 using two solid rivets
B0205016AD5-8S.
(d) In a suitable area next to new bracket 85714527-001 re-identify rib
85713380-001 as 8Z6836-3 using an indelible marker.
NOTE: Make sure that the fuel lines installed in the step below have a minimum
clearance of no less that 0.125 inch from adjacent structure.
(6) Refer to AMM TASK 28-21-06-400-801 and drawing 8Z9609-ASSY -001 and
install / route new fuel feed lines 82822139-005 and 82822140-003. Secure the
fuel feed lines using kept clamps, screws and washers. Make sure to install new
preformed O-rings MS29513-214 at each coupling B030508A16 during
assembly.
(7) If any discrepancy exists record the condition then contact the ‘‘Toronto Help
Desk at telephone number (416) 375-4000 or facsimile (416) 375-4539’’ or
E-mail: thd.qseries@aero.bombardier.com for a corrective action .
NOTE: Fuel lines designed with a protective teflon sleeve installed around the
tube adjacent to wing structure are not required to achieve the minimum
clearance requirement of no less that 0.125 inch from adjacent structure.
(8) Refer to drawing 8Z9214-ASSY-001 SHN-VIEW LKG DOWN and DETAIL A and
install and secure one teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent to rib 85713802 at approx.
station Y-245.019. Install clamp 1.50 inches from the end of the teflon hose.
Refer to AMM TASK 20-10-01-430-801 and tighten the clamp fastener.
(9) Refer to drawing 8Z9214-ASSY-001-VIEW LKG DOWN and DETAIL A and install
and secure one teflon hose DSC411-12-0032 and one clamp B0305078-10
around scavenge fuel line adjacent rib 85713806 at approx. station Y-317.019.
Install clamp 1.50 inches from the end of the teflon hose. Refer to AMM TASK
20-10-01-430-801 and tighten the clamp fastener.

### Page 12

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 12 of 18
17 Aug 2012
MG
(10) Refer to drawing 8Z9609-ASSY -001-VIEW B and install and secure one teflon
hose DSC411-6-0026 and two clamps B0305078-04 to motive flow line
82822065 at approx. station Y-117.500 as shown.
(11) Refer to the applicable instructions in AMM TASK 28-21-00-780-801 and do a
pressure test of the left side fuel feed lines. Make sure a 0.125 inch (1/8 inch)
clearance between fuel line and wing structure is kept during pressure test.
(12) Go to the Close Out section and install the left wet bay and outer wing fuel tank
access panels OR go to PART 2 and rework the right side fuel tanks.
Part 2 - Rework of the Right Side Fuel Tank
(1) Refer to Figure 4 and remove and discard cushion clamps and related hardware
that secures existing fuel feed line 82822143-001 to adjacent scavenge line at
approx. Y-150.00.
(2) Refer to applicable instructions in AMM TASK 28-21-06-000-801 and Figure 4
and locate and remove engine fuel feed lines 82822142-003, 82822143-001 and
82822144-001 (including related cushion clamps and hardware). Keep related
cushion clamps and related hardware.
(3) Cap all open fuel lines. Send the removed fuel lines to stores to determine
disposition.
(4) Install new replacement bracket 85714428-003 to rib at station Y-136.300 in the
right side fuel tank as follows:
(a) Refer to Figure 4-Flag Note 1 and locate, carefully remove and discard one
existing bracket from rib p/n 85713370-002 at station Y-136.300.
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Refer to drawing 8Z6836-VIEW LOOKING RIB ASSY INBD AT
Y102D-136.30 LH and VIEW B and install new bracket 85714428-003 to rib
85713370-002 at station Y-136.300 using solid rivets B0205016AD5-7S.
(d) In a suitable area next to new bracket 85714428-003 re-identify rib
85713370-002 as 8Z6836-2 using an indelible marker.
(5) Install new replacement bracket 85714426-003 to rib at station Y-157.825 in the
right side fuel tank as follows:
(a) Refer to Figure 4-Flag Note 2 and locate, carefully remove and discard one
existing bracket from rib 85713380-002 at station Y-157.825.

### Page 13

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 13 of 18
17 Aug 2012
MG
(b) Deburr the vacated rivet holes and treat with a layer of alodine and touch
up with a layer of DHMS C4.06 Type 1, Class A, Grade A or Grade B
(Coating, Corrosion Preventative for Aircraft Integral Fuel Tanks).
(c) Refer to drawing 8Z6836-VIEW LOOKING RIB ASSY INBD AT
Y102D-157.825 LH and VIEW D and install new bracket 85714426-003 to
rib at station Y-157.825 using two solid rivets B0205016AD5-8S.
(d) In a suitable area next to new bracket 85714526-003 re-identify rib
85713380-002 as 8Z6836-4 using an indelible marker.
NOTE: Make sure that fuel lines installed in the steps below have a minimum
clearance of no less that 0.125 inch from adjacent structure.
(6) Refer to AMM TASK 28-21-06-400-801 and drawing 8Z9609-ASSY -003 and
install / route new fuel feed lines 82822142-005, 82822143-003, 82822144-005.
Secure the fuel feed lines using kept clamps, screws and washers. Make sure to
install new O-rings MS29513-214 at each coupling B030508A16 during
assembly.
(7) If any discrepancy exists record the condition then contact the ‘‘Toronto Help
Desk at telephone number (416) 375-4000 or facsimile (416) 375-4539’’ or
E-mail: thd.qseries@aero.bombardier.com for a corrective action.
(8) Install and secure one Teflon hose DSC411-6-0026 and two clamps
B0305078-04 around tube assembly 82822065 (motive flow) at approx. station
Y-117.500 to agree with detail views gi ven on drawing 8Z9609 ASSY -002, detail
VIEW B and NOTES 7, 8 and 9.
NOTE: Fuel lines designed with a protective teflon sleeve installed around the
tube adjacent to wing structure are not required to achieve the minimum
clearance requirement of no less that 0.125 inch from adjacent structure.
(9) Refer to drawing 8Z9214-ASSY-002 OPP-VIEW LKG DOWN and DETAIL A and
install and secure one teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent to rib 85713802 at approx.
station Y-245.019. Install clamp 1.50 inches from the end of the teflon hose.
Refer to AMM TASK 20-10-01-430-801 and tighten the clamp fastener.
(10) Refer to drawing 8Z9214-ASSY-002 OPP-VIEW LKG DOWN and DETAIL A and
install and secure one teflon hose DSC411-12-0032 and one clamp
B0305078-10 around scavenge fuel line adjacent rib 85713806 at approx. station
Y-317.019. Install clamp 1.50 inches from the end of the teflon hose. Refer to
AMM TASK 20-10-01-430-801 and tighten the clamp fastener.

### Page 14

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 14 of 18
17 Aug 2012
MG
(11) Do a pressure test of the fuel feed lines (right side) to agree with applicable
instructions in AMM TASK 28-21-00-780-801. Make sure a 0.125 inch (1/8 inch)
clearance between fuel line and wing structure is kept during pressure test.
C. Close Out
(1) Make sure to remove all debris and unwanted material(s) from the fuel tanks.
(2) Refer to AMM TASK 57-11-01-400-801 and the table below and install the left
and/or right wing wet bay fuel tank access panels.
ACCESS DESIGNATION
523AT (left wing) and/or 623AT (right wing) Wet Bay Fuel Access Panels
522BT (left wing) and/or 622BT (right wing) Wet Bay Fuel Access Panels
522CT (left wing) and/or 622CT (right wing) Wet Bay Fuel Access Panels
(3) Refer to AMM TASK 57-21-01-400-801 and the table below and install the outer
wing fuel access panels.
ACCESS DESIGNATION
524AT (left wing) and/or 624AT (right wing) Outer Wing Fuel Access Panels
524CT (left wing) and/or 624CT (right wing) Outer Wing Fuel Access Panels
(4) Remove all tools and equipment from the work area.
(5) On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applic able logbook(s). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.

### Page 15

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 15 of 18
17 Aug 2012
MG
Location of Rework
Figure 1
REWORK-LEFT HAND WING
REWORK-RIGHT HAND WING

### Page 16

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 16 of 18
17 Aug 2012
MG
Removal and Installation of Fuel Access Panels
Figure 2
LH SIDE SHOWN, RH SIDE OPPOSITE
EXCEPT AS NOTED
523AT (LHS)
623AT (RHS)
522CT (LHS)
622CT (RHS)
524AT (LHS)
624AT (RHS)
524CT (LHS)
624CT (RHS)
YW - -42.000
522BT (LHS)
622BT (RHS)

### Page 17

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 17 of 18
17 Aug 2012
MG
Removal of Existing Clipping and Fuel Feed Lines - Left Side Fuel Tank
Figure 3
AC
CL
82822139-003
ENG FUEL FEED LINE
REMOVE EXISTING
REMOVE EXISTING BRACKET.
INSTALL NEW BRACKETS AT SAME LOCATION
1
NOTES:
RIB
85713370-001
2
1 2
85713380-001
RIB
Y- -42.00
Y- -117.500
Y- -136.300
Y- -157.820
Y- -191.200
LEFT WING TOP VIEW SHOWN.
REAR SPAR
REMOVE EXISTING
ENG FUEL FEED LINE
82822140-001

### Page 18

SERVICE BULLETIN 84-28-15
S.B. 84-28-15
Page 18 of 18
17 Aug 2012
MG
Removal of Existing Clipping and Fuel Feed Lines - Right Side Fuel Tank
Figure 4
Y-173.200
Y-157.825
Y-136.300
Y-25.258
ENG FUEL FEED LINE
REMOVE EXISTING
82822143-001
ENG FUEL FEED LINE
REMOVE EXISTING
82822144-001
ENG FUEL FEED LINE
REMOVE EXISTING
82822142-003
Y-117.500
1 2
NOTES:
1 2 REMOVE EXISTING BRACKET.INSTALL NEW BRACKETS AT SAME LOCATION
RIB
85713370-001 RIB85713380-002EXISTING CLIPPING
EXISTING FUEL FEED LINE
EXISTING SCAVENGE LINE
RIGHT WING TOP VIEW SHOWN.
REMOVE AND DISCARD
1

### Page 19

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 20

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
