# Bombardier Service Bulletin 84-32-114

Copy: Revision B ("FAA-2015-3986 SB 84-32-114B"), 26 pages: PDF https://openairdocs.org/files/sha256/a9/60/a96099f53a23740b1893a0a6c1c4bce4bf94fd0767819718dfaa26820f3ec9ce; text https://openairdocs.org/service-documents/bombardier/sb-84-32-114/file/a96099f53a23.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-3986; AD 2016-16-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-32-114
- Latest revision known: 84-32-114, Revision B, dated February 3, 2015 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-32-114

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-16-15](https://openairdocs.org/ad/2016-16-15.md), effective Sep 23, 2016: Revisions A and B

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-32-114/proposed.md).

## Text (26 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-3986; AD 2016-16-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘B’ 03 Feb 2015
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
Landing Gear - - - Retrofit - - - Redress Gear Harness Routing to Address
Interference with Stabilizer Brace - - - ModSum 4- - - 126562
This page transmits Revision ‘B’ of Service Bulletin 84- - -32- - -114, pages 1
thru 22 dated 03 Feb 2015.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- t h eDescription section is revised to add additional information
--- t h eCompliance section is revised to add Airworthiness Directive number
--- t h e Material Price and Availability section is revised to add kits
8MK4615- - -006/- - -007/- - -009/- - -051 and a Note
--- t h eReferences section is revised to convey the latest revision of this service
bulletin and related engineering documentation
--- t h eParts Required Per Aircraft section is revised to add additional parts to kit
8MK4615- - -001, add kits 8MK4615- - -006/- - -007/- - -009/- - -051
--- t h eACCOMPLISHMENT INSTRUCTIONS section is revised to add additional
steps and Notes
- - - steps (1) (f) & (g) in the Procedure section are revised to show correct Views
--- s t e p ( 2 ) ( g ) i n t h eProcedure section is revised to show the correct flagnote
The Compliance in the previous issue of this service bulletin is not affected
by this revision. Additional rework to the aircraft is introduced by this
revision.

### Page 2

Remove the previous issue of Service Bulletin 84- - -32- - -114 and replace with
attached.
Previous issue(s) of Service Bulletin 84- - -32- - -114:
Initial issue - - - Pages 1 thru 22 dated 06 Jun 2013
Revision ‘A’ - - - Pages 1 thru 22 dated 18 Sep 2013

### Page 3

D
S.B. 84- - -32- - -114
Page 1 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 3211 NUMBER: 84- - -32- - -114
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Landing Gear - - - Retrofit - - - Redress Gear Harness Routing to
Address Interference with Stabilizer Brace - - - ModSum 4- - - 126562
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4411.
NOTE: If ModSum IS4Q2400028 was previously accomplished on aircraft
Serial Numbers 4001 and 4003 thru 4089, no further action is required.
NOTE: If ModSum IS4Q2400029 was previously accomplished on aircraft
Serial Numbers 4090 thru 4411, no further action is required.
Production: ModSum 4- - -123798 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Numbers 4412 thru 4452.
ModSum 4- - -126562 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Numbers 4453 and
subsequent.

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 2 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None
B. Reason
Problem: The clearance between the MLG stabilizer brace and the nacelle A- - -Frame
can be insufficient for some harness routings. With the insufficient
clearance, there is a potential interference between the MLG stabilizer
brace, electrical harness and nacelle A- - -Frame possibly causing damage
to all three components.
Solution: This service bulletin introduces ModSum 4- - -126562.
The ModSum redresses the MLG electrical harness to improve the
clearance between the MLG electrical harness, stabilizer brace and
nacelle A- - -Frame.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- - - nose landing gear lock is engaged
- - - main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- - - pressure in the No. 1, 2 & 3 hydraulic systems are depleted
- - - all aircraft electrical power systems are selected to OFF
- - - aircraft is lifted on jacks
- - - LH and RH MLG stabilizer struts are removed as required for access
- - - LH and RH MLG forward doors are removed
- - - work platforms or ladders are set up and properly grounded
- - - LH and RH MLG electrical harness are reworked per drawings 8Z9552 and 8Z9553

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 3 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
- - - clearance between the stabilizer brace and electrical harnesses on both LH and
RH nacelles is measured
- - - LH and RH nacelle A- - -Frames and MLG stabilizer braces are checked for signs
of chafing
- - - LH and RH MLG forward doors are installed
- - - operational test of the landing gear primary extension and retraction system is
done
- - - close out.
D. Compliance
Bombardier Inc. highly recommends that ModSum 4- - -126562 be incorporated at
the earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
Transport Canada Airworthiness Directive CF- - -2014- - -45.
ModSum IS4Q2400028 or IS4Q2400029 is equivalent to ModSum 4- - -126562.
There is no need to incorporate ModSum 4- - -126562 if ModSums IS4Q2400028 or
IS4Q2400029 has already been incorporated.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
O r g a n i z a t i o n N o : D A O # 9 3 --- Q --- 0 2 .
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 4 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
F. M a n p o w e r
It will take an estimated 12 man- - -hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.50
Procedure 10.00
T e s t/R T S 1.00
Close- - -Out 0.50
For any on- - -site labor assistance, please speak with a Fleet Services representative for
a quote. The Fleet Services group can be contacted via the Q Series T echnical Help
Desk by telephone at 416- - -375- - -4000 or email at: thd.qseries@aero.bombardier.com.
G. Material - - - Price and Availability
The ModKits required to do this service bulletin are listed in the table below:
Operators should submit a purchase orde r through the Customer Accounts Service
T eam (CAST) at Bombardier Aerospace Regional Aircraft division specifying aircraft
serial number(s) to:
Bombardier Aerospace
Customer Accounts Services T eam (Mail Stop N11- - -32)
123 Garratt Blvd.
To r o n t o
Ontario
Canada M3K- - -1Y5
Facsimile: (416) 375- - -3060
T elephone: (416) 375- - -3920
Facsimile:
International: (416) 375- - -3334
European: (416) 373- - -5966
Americas East: (416) 373- - -5964
Americas West: (416) 373- - -5965
T elephone:

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 5 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
International: (416) 375- - -3706
European: (416) 373- - -3704
Americas East: (416) 375- - -3700
Americas West: (416) 373- - -5888
E- - -mail addresses:
International: cast.international@aero.bombardier.com
European: cast.europe@aero.bombardier.com
Americas East: cast.americaseast@aero.bombardier.com
Americas West: cast.americaswest@aero.bombardier.com
Kit Number Description
8MK4615- - -001 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, LH Nacelle - - - See NOTE 1
8MK4615- - -002 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, RH Nacelle - - - See NOTE 2
8MK4615- - -003 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, LH Nacelle - - - See NOTE 3
8MK4615- - -004 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, RH Nacelle - - - See NOTE 4
8MK4615- - -005 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, LH Nacelle - - - See NOTE 4
8MK4615- - -006 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, RH Nacelle - - - See NOTE 4
8MK4615- - -007 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, LH Nacelle - - - See NOTE 4
8MK4615- - -009 K i t --- R e w o r k --- E l e c C o n d u i t A s s e m b l y, L / G
Harness, LH Nacelle - - - See NOTE 3
8MK4615- - -051 D e l t a K i t --- S e e N O T E 5
NOTE 1: Applicable to aircraft serial numbers 4001 thru 4027.
NOTE 2: Applicable to aircraft serial numbers 4001 thru 4089.
NOTE 3: Applicable to aircraft serial numbers 4028 thru 4089.

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 6 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE 4: Applicable to aircraft serial numbers 4090 thru 4411.
NOTE 5: For any unconsumed 8MK4615- - -003/- - -004/- - -005 kits, operators
only need to order delta kit 8MK4615- - -051.
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1- - -84- - -4....................
Wiring Diagrams Manual PSM 1- - -84- - -2W............................
ModSums Manual PSM 1- - -84- - -12..................................
L. References
Revision ‘B’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4615 1 E
8Z9552 1 E
8Z9552 2 D
8Z9552 3 C
8Z9553 1 E
8Z9553 2 D
8Z9553 3 B
8Z9553 4 B
ModSum 4Q126562 Rev. ‘F’

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 7 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
ModSum 4- - -126562 Rev. ‘F’
ModSum 4Y123798 Rev. ‘B’
ModSum 4- - -123798 Rev. ‘B’
ModSum IS4Q2400028 Rev. ‘B’
ModSum IS4Q2400029 Rev. ‘A’
PCA 44059 Revision 1 (for internal reference only)
Transport Canada Airworthiness Directive CF- - -2014- - -45
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4615- - -001, for aircraft serial numbers 4001 thru 4027.
Modification Kit 8MK4615- - -002, for aircraft serial numbers 4001 thru 4089.
(2) Detailed Kit Content:
Quantity Per Kit
--- 0 0 2 --- 0 0 1
Part Number Description Remarks
2 B0816035AA3N750 Tie Mount
5 B0816019- - -001 Strap Tie Down
1 8Z9553 R e w o r k --- L d g G e a r
Harness LH Nacelle
Drawing Only
1 8Z9552 R e w o r k --- L d g G e a r
Harness RH Nacelle
Drawing Only
44 TR04AI Tinel- - -Lock Ring See NOTE 1
6f t . 6f t . MIL- - -I- - -19166 Fibreglass T ape
44 202A121- - -3/42 Boot HT Shrink See NOTE 1
11 B0204046CRA3- - -20 Clickbond Standoff See NOTE 2
1 CSP255- - -8Z9553- - -051 Label
1 CSP255- - -8Z9552- - -051 Label
11 MS21919WDE12 Clamp
6f t 6f t 3C- - -CML- - -1NSNJ- - -0006Conduit See NOTE 1
11 B0816035CR3TT Cable Tie Mount

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 8 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
Quantity Per Kit
--- 0 0 2 --- 0 0 1
RemarksDescriptionPart Number
88 M39029/56- - -351 Pin, Contact
65 B0816035CR3T Cable Tie Mount See NOTE 3
6f t . 6f t . DSC230- - -7HT Spiral Wrap
1f t . 1f t . MS21266- - -2N Grommet Edging
11 MS21919WDE10 Clamp
11 NAS1801- - -3- - -10 Screw
11 NAS1801- - -3- - -16 Screw
61 B0816038- - -002 Connector Ring
13 12 B0816019- - -003 Tie Strap
NOTE 1: If required. Replace the conduit assembly with these parts.
NOTE 2: Acceptable to use substitute part CB3001CRA3- - -20.
NOTE 3: Acceptable to use substitute part CB3019CR3T , CSP458- - -1 or
B0816033- - -002.

### Page 11

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 9 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
(3) Modification Kit 8MK4615- - -003, for aircraft serial numbers 4028 thru 4089.
Modification Kit 8MK4615- - -004, for aircraft serial numbers 4090 thru 4411.
Modification Kit 8MK4615- - -005, for aircraft serial numbers 4090 thru 4411.
(4) Detailed Kit Content:
Quantity Per Kit
--- 0 0 5 --- 0 0 4 --- 0 0 3
Part Number Description Remarks
11 8Z9553 R e w o r k --- L d g G e a r
Harness LH Nacelle
Drawing Only
1 8Z9552 R e w o r k --- L d g G e a r
Harness RH Nacelle
Drawing Only
444 TR04AI T i n e l --- L o c k R i n g See NOTE 1
6f t . 6f t 6f t . MIL- - -I- - -19166 Fibreglass T ape
444 202A121- - -3/42 Boot HT Shrink See NOTE 1
1 B0204046CRA3- - -20 Clickbond Standoff See NOTE 2
11 CSP255- - -8Z9553- - -051 Label
1 CSP255- - -8Z9552- - -051 Label
6f t . 6f t . 6f t . 3C- - -CML- - -1NSNJ- - -0006Conduit See NOTE 1
111 B0816035CR3TT Cable Tie Mount
888 M39029/56- - -351 Pin, Contact
41 B0816035CR3T Cable Tie Mount See NOTE 3
6f t . 6f t . 6f t . DSC230- - -7HT Spiral Wrap
1f t . 1f t . 1f t . MS21266- - -2N Grommet Edging
111 MS21919WDE10 Clamp
222 MS21919WDE7 Clamp
111 NAS1801- - -3- - -20 Screw
111 NAS43DD3- - -40FC Spacer
122 B0816038- - -002 Connector Ring
444 B0305091- - -5 Clamp
71 5 7 B0816019- - -003 Tie Strap
444 CSP458- - -1 Tie Mount
NOTE 1: These parts are required if the conduit assembly is replaced.
NOTE 2: Acceptable to use substitute part CB3001CRA3- - -20.
NOTE 3: Acceptable to use substitute part CB3019CR3T , CSP458- - -1 or
B0816033- - -002.

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 10 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
(5) Modification Kit 8MK4615- - -006, for aircraft serial numbers 4090 thru 4411.
Modification Kit 8MK4615- - -007, for aircraft serial numbers 4090 thru 4411.
Modification Kit 8MK4615- - -009, for aircraft serial numbers 4028 thru 4089.
(6) Detailed Kit Content:
Quantity Per Kit
--- 0 0 9 --- 0 0 7 --- 0 0 6
Part Number Description Remarks
2 B0816035AA3N750 Tie Mount
5 B0816019- - -001 Strap Tie Down
111 B0305091- - -9 Clamp
333 B0305091- - -6 Clamp
11 8Z9553 R e w o r k --- L d g G e a r
Harness LH Nacelle
Drawing Only
1 8Z9552 R e w o r k --- L d g G e a r
Harness RH Nacelle
Drawing Only
444 TR04AI Tinel- - -Lock Ring See NOTE 1
6f t . 6f t 6f t . MIL- - -I- - -19166 Fibreglass T ape
444 202A121- - -3/42 Boot HT Shrink See NOTE 1
1 B0204046CRA3- - -20 Clickbond Standoff See NOTE 2
11 CSP255- - -8Z9553- - -051 Label
1 CSP255- - -8Z9552- - -051 Label
6f t . 6f t . 3C- - -CML- - -1NSNJ- - -0006Conduit See NOTE 1
111 B0816035CR3TT Cable Tie Mount
888 M39029/56- - -351 Pin, Contact
41 B0816035CR3T Cable Tie Mount See NOTE 3
6f t . DSC230- - -7HT Spiral Wrap
1f t . MS21266- - -2N Grommet Edging
111 MS21919WDE10 Clamp
222 MS21919WDE7 Clamp
111 NAS1801- - -3- - -20 Screw
111 NAS43DD3- - -40FC Spacer
212 B0816038- - -002 Connector Ring
77 1 5 B0816019- - -003 Tie Strap
444 CSP458- - -1 Tie Mount
NOTE 1: These parts are required if the conduit assembly is replaced.

### Page 13

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 11 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE 2: Acceptable to use substitute part CB3001CRA3- - -20.
NOTE 3: Acceptable to use substitute part CB3019CR3T , CSP458- - -1 or
B0816033- - -002.
(7) Modification Kit 8MK4615- - -051, for any unconsumed
8MK4615- - -003/- - -004/- - -005 kits.
(8) Detailed Kit Content:
Quantity Per Kit
--- 0 5 1
Part Number Description Remarks
1 B0305091- - -9 Clamp
3 B0305091- - -6 Clamp
(9) In addition to the above part(s), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in
either Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter
51 or, for 400 Series Aircraft, in Consumable Products Manual (CPM) PSM
1 --- 8 4 --- 1 8 .
Product ID No. Qty. Per Aircraft Description Specifications*
05- - -03 As Required Adhesive, Modified
Epoxy
DHMS A6.12
DOD- - -A- - -82720
06- - -01 As Required Sealant, T empera-
ture Resistant
DHMS S3.01
SAE AMS- - -S8802A
ASTMD412
B M S 3 --- 1 1 G
MIL- - -STD- - -1916
*NOTE: Refer to CPM PSM 1- - -84- - -18 for the list of approved alternative
consumable products under each Product Id No., any of which
can be used unless a note states otherwise.

### Page 14

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 12 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
(1) Make sure the nose gear ground lock is engaged.
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(3) Set wheel chocks in front and behind the landing gear tires.
(4) Deplete hydraulic pressure in the No. 1, 2 & 3 systems (refer to AMM TASKs
29- - -00- - -00- - -863- - -802 and 29- - -00- - -00- - -863- - -804).
(5) Install a warning sign on the external hydraulic connection.
(6) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K s 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(7) Lift the aircraft on jacks (refer to applicable instructions in AMM T ask
07- - -10- - -00- - -582- - -801).
(8) Remove the LH and RH MLG stabilizer struts as required for access (refer to
applicable instructions in AMM TASK 32- - -11- - -16- - -000- - -801).
(9) Remove the LH and RH MLG forward doors (refer to applicable instructions in
AMM TASK 32- - -12- - -11- - -000- - -801).
(10) Set up work platforms or ladders as required to gain access to the stabilizer
brace in the No. 1 and/or No. 2 wheel well. Make sure that the work platforms or
ladders are electrically grounded.
B. Procedure
NOTE: The rework is limited to the tasks that follow:
- - - The repair of the conduit assembly that may be damaged due to MLG
stabilizer brace interference on harness.
- - - Rerouting the conduit assembly to eliminate fouling condition on the
nacelle A- - -Frame.

### Page 15

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 13 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE: Existing cable routing may vary between aircraft due to modification
configuration.
(1) Rework the LH MLG electrical wiring harness as follows (refer to drawing
8Z9553):
(a) Disconnect the conduit assembly 82440848 on ends 3261- - -J24 & 3261- - -J22
and conduit assembly 82440845 on ends 3261- - -J21 & 3261- - -J23 (refer to
drawing 8Z9553 sheet 1 to 4).
(b) Undo the clippings of the conduit assembly on area shown on drawing
8Z9553 sheet 2 VIEW B- - -B and VIEW A. Keep hardware for re- - -installation as
the conduit will be rerouted (refer to drawing 8Z9553 sheet 2 VIEW W- - -W).
(c) Do an inspection of the conduit assembly for the conditions that follow and
rectify as necessary per the Wiring Diagram Manual Chapters
20- - -12- - -10- - -201, 20- - -15- - -04- - -201 and 20- - -15- - -10- - -401.
1 Foreign object damage (FOD).
2 Damage due to sharp bends and kinking and deterioration.
3 Condition of overbraid for cracking.
4 Sign of damage to the overbraid due to fouling structures.
5 Chafing.
(d) If the inspection is satisfactory, re- - -install the electrical conduit assembly per
drawing 8Z9553.
NOTE: Make sure the cables are kept below the reference line as shown by
flagnote 15 in dwg 8Z9553 sheet 2 VIEW B- - -B or sheet 3 VIEW B- - -B or
sheet 4 VIEW B1- - -B1 or VIEW B2- - -B2 as applicable, then continue to
section (f).
(e) If conduit is damaged, replace the damaged conduit on conduit assembly as
follows:
1 Disassemble conduit (refer to drawing 8Z9553 sheet 1 DETAIL G and
applicable instructions in Wiring Diagram Manual T ask
20- - -15- - -10- - -401).
2 Do an inspection of the two connectors, two 90 _ connector backshells,
two straight adaptors and one Y- - -transition for condition and keep them
for re- - -installation if they are in good condition (refer to drawing 8Z9552
sheet 1 flagnote 6).

### Page 16

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 14 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE: The components are considered to be in good condition if they have
minimal paint chaffing, level 1 corrosion or less and no impact damage.
R e f e r t o Q --- S e r i e s C P C M a n u a l ( P S M --- 1 G E N --- 5 ) .
NOTE: The connectors, 90 _ connector backshells, straight adaptors and
Y- - -transition may show sign of deterioration but not due to MLG stabilizer
brace interference on harness. These parts have to be procured by the
customer if replacement parts are nece ssary for re- - -installation (refer to
drawing 8Z9552 sheet 1 flagnote 13). Contact the Bombardier Aerospace
T echnical Help Desk for part information if required.
3 Remove wires from connectors 3261- - -J24 and 3261- - -J22 (refer to
drawing 8Z9553 sheet 1 flagnote 7 and applicable instructions in Wiring
Diagram Manual Chapter 20 Wiring Standard Practices).
4 Rework conduit assembly 82440848 on connectors 3261- - -J24 and
3261- - -J22 (refer to drawing 8Z9553 sheet 1 flagnote 8 and applicable
instructions in Wiring Diagram Manual T ask 20- - -15- - -10- - -401), adaptors
connectors that are used to terminate the overbraid and individual
wireshield that protects the EMI and HIRF during removal and
installation as follows:
a Replace damaged overbraid conduit.
b Reterminate wiring (refer to drawing 8Z9553 sheet 1 flagnote 8 and
WIRING DIAGRAM).
c Install adapters, tinel ring, conduit and heat shrink boots (refer to
applicable instructions in WDM T ask 20- - -15- - -10- - -401).
d Complete assembly of the conduit assembly and re- - -install (refer
to drawing 8Z9553).
NOTE: Similar repair procedure can be done on conduit assembly 82440845
(3261- - -J21 & 3261- - -J23) if required. Contact the Bombardier Aerospace
T echnical Help Desk for part information if required.
NOTE: Make sure the cables are kept below the reference line as shown by
flagnote 15 in dwg 8Z9553 sheet 2 VIEW B- - -B or sheet 3 VIEW B- - -B or
s h e e t 4 V I E W B 1 --- B 1 o r V I E W B 2 --- B 2 a s a p p l i c a b l e .
e Do a check of the inductance value of proximity sensors LGWOW2
(S02) and LGDLK2 (S08) (refer to applicable instructions in AMM
32- - -61- - -00- - -280- - -801).

### Page 17

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 15 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE: This check can be done before Close Out.
(f) Install edge grommet MS21266- - -2N (refer to flagnote 16 in dwg 8Z9553
s h e e t2V I E WB - - - B ,s h e e t3V I E WB - - - Ba n ds h e e t4V i e wB 1 - - - B 1&
B2- - -B2).
(g) Cover electrical cables and hydraulic lines with spiral wrap DSC230- - -7HT
as necessary (refer to flagnote 21 in dwg 8Z9553 sheet 2 VIEW S- - -S, sheet
3V I E WAa n ds h e e t4V i e wA ) .
(h) Do an electrical bonding through direct interface contact (refer to drawing
8Z9553 sheet 1 flagnote 9 and to applicable instructions in AMM T ask
5 1 --- 8 0 --- 0 0 --- 1 2 0 --- 8 0 1 a n d S R M Ta s k 5 1 --- 8 0 --- 0 0 --- 0 2 --- 0 1 ) .
(i) Bond with Epoxy adhesive (product ID No. 05- - -03). After cure, seal edge base
with sealant (Product ID No. 06- - -01) (refer to CPM PSM 1- - -84- - -18 and to
drawing 8Z9553 sheet 2 flagnote 10 and to applicable instructions in AMM
51- - -23- - -00- - -390- - -801).
(j) Install label (refer to drawing 8Z9553 sheet 1 flagnote 11 and to applicable
instructions in AMM 20- - -00- - -16- - -400- - -801).
(k) Dress up routing to make sure harness is firmly secured and not fouling on the
frame (refer to drawing 8Z9553 sheet 2 flagnote 12).
(2) Rework the RH MLG electrical wiring harness as follows (refer to drawing
8Z9552):
(a) Disconnect the conduit assembly 82440850 on ends 3261- - -J44 & 3261- - -J42
and conduit assembly 82440841 on ends 3261- - -J41 & 3261- - -J43 (refer to
drawing 8Z9552 sheet 1 to 3).
(b) Undo the clippings of the conduit assembly on area shown on drawing
8Z9552 sheet 2 VIEW B- - -B and VIEW A. Keep hardware for re- - -installation as
the conduit will be rerouted (refer to drawing 8Z9552 sheet 2 VIEW BX- - -BX).
(c) Do an inspection of the conduit assembly for the conditions that follow and
rectify as necessary per the Wiring Diagram Manual Chapters
20- - -12- - -10- - -201, 20- - -15- - -04- - -201 and 20- - -15- - -10- - -401.
1 Foreign object damage (FOD).
2 Damage due to sharp bends and kinking and deterioration.
3 Condition of overbraid for cracking.
4 Sign of damage to the overbraid due to fouling structures.
5 Chafing.
(d) If the inspection is satisfactory, re- - -install the electrical conduit assembly per
drawing 8Z9552.

### Page 18

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 16 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
NOTE: Make sure the cables are kept below the reference line as shown by
flagnote 15 in dwg 8Z9552 sheet 2 VIEW B- - -B or sheet 3 VIEW B- - -B,
VIEW B1- - -B1 and VIEW B2- - -B2 as applicable, then continue to section
(f).
(e) If conduit is damaged, replace the damaged conduit on conduit assembly as
follows:
1 Disassemble conduit (refer to drawing 8Z9552 sheets 1 and 2 DETAIL G
and applicable instructions in Wiring Diagram Manual T ask
20- - -15- - -10- - -401).
2 Do an inspection of the two connectors, two 90 _ connector backshells,
two straight adaptors and one Y- - -transition for condition and keep them
for re- - -installation if they are in good condition (refer to drawing 8Z9552
sheet 1 flagnote 6).
NOTE: The components are considered to be in good condition if they have
minimal paint chaffing, level 1 corrosion or less and no impact damage.
R e f e r t o Q --- S e r i e s C P C M a n u a l ( P S M --- 1 G E N --- 5 ) .
NOTE: The connectors, 90 _ connector backshells, straight adaptors and
Y- - -transition may show sign of deterioration but not due to MLG stabilizer
brace interference on harness. These parts have to be procured by the
customer if replacement parts are nece ssary for re- - -installation (refer to
drawing 8Z9552 sheet 1 flagnote 13). Contact the Bombardier Aerospace
T echnical Help Desk for part information if required.
3 Remove wires from connectors 3261- - -J44 and 3261- - -J42 (refer to
drawing 8Z9552 sheet 1 flagnote 7 and applicable instructions Wiring
Diagram Manual Chapter 20 Wiring Standard Practices).
4 Rework conduit assembly 82440850 on connectors 3261- - -J44 and
3261- - -J42 (refer to drawing 8Z9552 sheet 1 flagnote 8 and applicable
instructions in Wiring Diagram Manual (WDM) T ask 20- - -15- - -10- - -401),
adaptors connectors that are used to terminate the overbraid and
individual wireshield that protects the EMI and HIRF during removal and
installation as follows:
a Replace damaged overbraid conduit.
b Reterminate wiring (refer to drawing 8Z9553 sheet 1 flagnote 8 and
WIRING DIAGRAM).
c Install adapters, tinel ring, conduit and heat shrink boots (refer to
applicable instructions in WDM T ask 20- - -15- - -10- - -401).

### Page 19

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 17 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
d Complete assembly of the conduit assembly and re- - -install (refer
to drawing 8Z9552).
NOTE: Make sure the cables are kept below the reference line as shown by
flagnote 15 in dwg 8Z9552 sheet 2 VIEW B- - -B or sheet 3 VIEW B- - -B,
VIEW B1- - -B1 and VIEW B2- - -B2 as applicable.
e Do a check of the inductance value of proximity sensors RGWOW2
(S06) and RGDLK2 (S14) (refer to applicable instructions in AMM
32- - -61- - -00- - -280- - -801).
NOTE: Similar repair procedure can be done on conduit assembly 82440841
(3261- - -J41 & 3261- - -J43) if required. Contact the Bombardier Aerospace
T echnical Help Desk for part information if required.
NOTE: This check can be done before Close Out.
(f) Install edge grommet MS21266- - -2N (refer to flagnote 16 in dwg 8Z9552
sheet 2 VIEW B- - -B and sheet 3 View B- - -B).
(g) Cover electrical cables and hydraulic lines with spiral wrap DSC230- - -7HT
as necessary (refer to flagnote 25 in dwg 8Z9552 sheet 2 VIEW A and
sheet 3 View A).
(h) Do an electrical bonding through direct interface contact (refer to drawing
8Z9552 sheet 1 flagnote 9 and to applicable instructions in AMM T ask
5 1 --- 8 0 --- 0 0 --- 1 2 0 --- 8 0 1 a n d S R M Ta s k 5 1 --- 8 0 --- 0 0 --- 0 2 --- 0 1 ) .
(i) Bond with Epoxy adhesive (product ID No. 05- - -03). After cure, seal edge base
with sealant (Product ID No. 06- - -01) (refer to CPM PSM 1- - -84- - -18 and to
drawing 8Z9552 sheet 2 flagnote 10 and to applicable instructions in AMM
51- - -23- - -00- - -390- - -801).
(j) Install label (refer to drawing 8Z9552 sheet 1 flagnote 11 and to applicable
instructions in AMM 20- - -00- - -16- - -400- - -801).
(k) Dress up routing to make sure harness is firmly secured and not fouling on the
frame (refer to drawing 8Z9552 sheet 2 flagnote 12).
(3) Measure the clearance between the stabi lizer brace and electrical harnesses on
both LH and RH nacelles as follows:
(a) Re- - -install the LH and RH MLG stabilizer struts as required (refer to applicable
instructions in AMM TASK 32- - -11- - -16- - -400- - -801).

### Page 20

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 18 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
(b) With the LH and RH MLG forward doors still removed from aircraft, do the
Operational T est of the Landing Gear Primary Extension and Retraction
System (refer to applicable instructions in AMM TASK
32- - -31- - -00- - -710- - -801).
(c) Retract the landing gear and leave in the up and locked position (refer to
applicable instructions in AMM T ask 32- - -31- - -00- - -867- - -801).
(d) Inspect the reworked area in the LH and RH nacelles and do a clearance
check between the MLG stabilizer brace and electrical harnesses (refer to
Figure 1 Sheets 1 to 3 and Figure 2). Make sure there is 0.100 in. (2.54 mm)
minimum clearance between the MLG stabilizer brace and electrical
harnesses.
(4) Check for signs of contact on LH and RH nacelle A- - -Frames and MLG stabilizer
braces (refer to Figure 1). If damage caused by contact was found, contact the
Q Series T echnical Help Desk by telephone at 416- - -375- - -4000 or email at:
thd.qseries@aero.bombardier.com for approved disposition/action.
(5) Extend the landing gear (refer to applicable instructions in AMM T ask
32- - -31- - -00- - -867- - -801).
(6) Install the LH and RH MLG forward doors (refer to applicable instructions in
AMM TASK 32- - -12- - -11- - -400- - -801).
(7) Do the operational test of the landing gear primary extension and retraction
system (refer to applicable instructions in AMM 32- - -31- - -00- - -710- - -801).
C. Close Out
(1) Lower the aircraft on jacks and remove the jacks (refer to applicable instructions
in AMM T ask 07- - -10- - -00- - -582- - -801).
(2) Remove all tools and equipment from the work area.
(3) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 21

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 19 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
Nacelle A- - - Frame and MLG Stabilizer Brace
Figure 1 (Sheet 1)
STABILIZER BRACE
A --- F R A M E
APPLICABLE ON A/C 4056 AND SUBS (POST MS 4- - -113159)
AND FIGURE 2) FOR SIGNS OF CHAFING.

### Page 22

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 20 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
A --- F R A M E
STABILIZER BRACE
Nacelle A- - - Frame and MLG Stabilizer Brace
Figure 1 (Sheet 2)
DURING MLG SWING,
CHECK FOR CLEARANCE
IN THIS AREA.
APPLICABLE ON A/C 4003 THRU 4055 (POST MS 4- - -113305)
F
F
AND FIGURE 2) FOR SIGNS OF CHAFING.

### Page 23

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 21 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
Nacelle A- - - Frame and MLG Stabilizer Brace
Figure 1 (Sheet 3)
x
0.100 IN.
(2.54 MM)
MINIMUM
0.100 IN.
(2.54 MM)
MINIMUM
0.100 IN.
(2.54 MM)
MINIMUM
0.100 IN.
(2.54 MM)
MINIMUM
AND FIGURE 2) FOR SIGNS OF CHAFING.
(MLG STABILIZER BRACE P/N 46400- - -25 AND PREV) (MLG STABILIZER BRACE P/N 46400- - -27 AND SUBS)
(MLG STABILIZER BRACE P/N 46400- - -27 AND SUBS) (MLG STABILIZER BRACE P/N 46400- - -25 AND PREV)
(AIRCRAFT SERIAL NUMBERS 4001 THRU 4055) (AIRCRAFT SERIAL NUMBERS 4056 THRU 4411)
(AIRCRAFT SERIAL NUMBERS 4056 THRU 4411)(AIRCRAFT SERIAL NUMBERS 4001 THRU 4055)

### Page 24

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 1 4
S.B. 84- - -32- - -114
Page 22 of 22
06 Jun 2013
JR
Revision ‘B’ 03 Feb 2015
Nacelle A- - - Frame and MLG Stabilizer Brace - - - Clearance Check
Figure 2
1

### Page 25

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 26

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
