# Bombardier Service Bulletin 84-32-122

Copy: Revision A ("SB 84-32-122 Rev A"), 18 pages: PDF https://openairdocs.org/files/sha256/ce/47/ce477e1140ad2f5178979f3ead0967559d1cd09509b00dccee5d8c4d795cd55e; text https://openairdocs.org/service-documents/bombardier/sb-84-32-122/file/ce477e1140ad.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-1050; AD 2015-17-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-32-122
- Latest revision known: 84-32-122, Revision A, dated October 4, 2013 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-32-122

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-17-08](https://openairdocs.org/ad/2015-17-08.md), effective Sep 29, 2015: Revision A

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-32-122/proposed.md).

## Text (18 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-1050; AD 2015-17-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘A’ 04 Oct 2013
DHC-8 (DASH 8)
SERVICE BULLETIN 84-32-122
Landing Gear - Nose Wheel Steering - Addition of Pull Down Resistors
to Pilot Hand Control (PHC) and Rudder Pedal Potentiometer - ModSum
4-126585
This page transmits Revision ‘A’ of Service Bulletin 84-32-122, pages 1 thru
14 dated 04 Oct 2013.
This service bulletin is re-issued in its entirety for the reasons that follow:
-t h e References section is revised to convey the latest revision of the service
bulletin and engineering documentation
-t h e Figures 3 and 4 are revised to add a NOTE stating that the figures were
taken from drawing 8Z9652 and to refer to the drawing for additional details.
The Compliance in the previous issues of this service bulletin is not affected
by this revision. No additional rework to the aircraft is introduced by this
revision.
Remove the previous revision of Service Bulletin 84-32-122 and replace with
attached.
Previous issue(s) of Service Bulletin 84-32-122:
Initial issue - Pages 1 thru 14 dated 28 Aug 2013

### Page 2

(No text on this page.)

### Page 3

D
S.B. 84-32-122
Page 1 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 3251 NUMBER: 84-32-122
SUBJECT: Landing Gear - Nose Wheel Steering - Addition of Pull Down
Resistors to Pilot Hand Control (PHC) and Rudder Pedal
Potentiometer - ModSum 4-126585
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service: DHC-8 Aircraft Models 401 and 402 Serial Numbers 4001 and
4003 thru 4448.
Production: ModSum 4-123898 will be installed before delivery on
applicable DHC-8 Aircraft at Serial Numbers 4449 and
subsequent.
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None

### Page 4

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 2 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
B. Reason
Problem: The possibility of uncommanded, un-annunciated and erratic steering
exists with the potential to cause runway/taxiway excursion.
Cause: If there is open circuit between the Pilot Hand Control (PHC) Potentiometer
and the Steering Control Unit (SCU) and/or between the Rudder Pedal
Potentiometer and the SCU, the fault may not detected and not
annunciated on the caution warning panel. With an open circuit in the
wiring between the PHC or Rudder and SCU, the nosewheel may rotate at
a high rate. It may rotate left or right over a 40 ˚ a n g l ef o rt h eP H Ca n d8˚
for the Rudder and remain at that angle with the nose wheel not going into
free castor mode.
The root of the problem is inherent to the design of the SCU and test
has shown it takes excessive time for an open circuit to be detected by
the SCU. The voltage drop in the SCU circuitry may not be sufficiently
fast enough before the nose wheel rotates to a severe angle. A
sustained open circuit between the SCU and PHC or Rudder
potentiometer may cause an uncommanded, un-annunciated hard over
steering event. This may lead to loss of directional control and potential
taxiway/runway excursion. The intermittent steering may also occur and
is manifested by erratic steering input signal.
Solution: This service bulletin incorporates ModSum 4-126585.
The ModSum installs a pull-down resistor that effectively trips the PHC or
rudder range monitor, reverting to fail safe free-castor mode, in the event
there is an open circuit between the PHC and rudder pedal potentiometers
and the SCU.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- all aircraft electrical power systems are selected to OFF
- the nose landing gear lock is engaged

### Page 5

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 3 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
- the main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- access panels 112AR and 122AR are removed
- flight crew oxygen cylinder is removed as necessary
- existing wires from connector pins of connector ends 3251-P1 and 9811-P2 are
removed
- continuity and resistance checks between pins are done before installation of new
harnesses
- new wire harnesses are installed
- continuity and resistance checks of wire harnesses between connector ends
3251-P1 and 9811-P2 are done
- functional test (open circuit test) of the nose wheel steering control system is done
- flight crew oxygen cylinder is installed if removed
- access panels 112AR and 122AR are installed
- close out.
D. Compliance
Bombardier Inc. recommends incorpora tion of ModSum 4-126585 at the earliest
opportunity unless otherwise directed by the operator’s airworthiness authority.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).

### Page 6

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 4 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
F. Manpower
It will take an estimated 5.5 man-hours to complete this service bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK MAN-HOURS
Job Set-Up 1.00
Procedure 3.00
Test / RTS 1.00
Close-Out 0.50
For any on-site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series Technical
Help Desk by telephone at 416-375-4000 or email at:
thd.qseries@aero.bombardier.com.
G. Material - Price and Availability
The ModKit required to do this service bulletin are listed in the table below:
Operators should submit a purchase orde r through the Customer Accounts Service
Team (CAST) at Bombardier Aerospace Regional Aircraft division specifying aircraft
serial number(s) to:
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K-1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920
Facsimile:
International: (416) 375-3334

### Page 7

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 5 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
European: (416) 373-5966
Americas East: (416) 373-5964
Americas West: (416) 373-5965
Telephone:
International: (416) 375-3706
European: (416) 373-3704
Americas East: (416) 375-3700
Americas West: (416) 373-5888
E-mail addresses:
International: cast.international@aero.bombardier.com
European: cast.europe@aero.bombardier.com
Americas East: cast.americaseast@aero.bombardier.com
Americas West: cast.americaswest@aero.bombardier.com
Kit Number Description
8MK4664 Rework Kit - NWS Addition of Resistor
H. Tooling - Price and Availability
None
I. Weight and Balance
A/C Type and Model Weight (Lb) Arm (Inches)
Moment
(Inches x Lb)
x 0.001
DHC-8 Model 401/402 +0.37 -108.70 -0.04
J. Electrical Load Data
Not affected

### Page 8

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 6 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
K. Publications Affected
Maintenance Manual PSM 1-84-2................................
Wiring Diagrams Manual PSM 1-84-2W............................
Dash 8 Illustrated Parts Catalogue PSM 1-84-4....................
ModSums Manual PSM 1-84-12..................................
Weight and Balance Manual (Imperial) PSM 1-84-8................
Weight and Balance Manual (Metric) PSM 1-84-8M..................
L. References
Revision ‘A’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4664 1 --
8Z9652 1 A
ModSum 4Q126585 Rev. ‘B’
ModSum 4-126585 Rev. ‘B’
ModSum 4Y123898 Rev. ‘B’
ModSum 4-123898 Rev. ‘B’
PCA 44578 Revision 0 (for internal reference only)
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4664-001

### Page 9

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 7 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
(2) Detailed Kit Content:
Quantity Per Kit
-001
Part Number Description Remarks
3 B0816063-003 Solder Sleeve See NOTE below
14 B0816063-002 Solder Sleeve See NOTE below
23 B0816063-001 Solder Sleeve See NOTE below
1 8Z9652-013 Cable Assy
1 8Z9652-011 Cable Assy
NOTE: These are additional sleeves included in the kit which may be used in the
event existing sleeves are damaged during disassembly.
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
(1) Placard and select all aircraft electrical power to OFF. Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASKs 24-00-00-861-802 and
24-00-00-910-801).
(2) Make sure the nose gear ground lock is engaged.
(3) Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(4) Set wheel chocks in front and behind the landing gear tires.

### Page 10

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 8 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
(5) Remove access panels 112AR and 122AR (refer to AMM TASK 06-41-00-992-801
for locations and to AMM TASK 53-11-00-000-801 for applicable instructions).
(6) For better access, remove the flight crew oxygen cylinder as necessary (refer to
AMM TASK 35-11-01-000-801 or TASK 35-11-01-000-802).
B. Procedure
(1) Locate connector ends 3251-P1 at the lower right side of the nose compartment
bay and 9811-P2 at RHS fwd pressure bulkhead (refer to Figure 2).
(2) Remove clamps. tie wraps and straps from existing wiring harnesses as
necessary.
(3) Remove the shield pigtails from backshell of connectors 3251-P1 and 9811-P2
and the wires from connector pins of connector 3251-P1 and 9811-P2 as follows
(refer to applicable instructions in WDM 20-12-10-201 and Figure 3):
From Pin Wire Code To Pin
3251-P1 35 W20A-22-6/BLK 9811-P2 A-
3251-P1 34 W20A-22-6/WHT 9811-P2 B-
3251-P1 36 W20A-22-6/RED 9811-P2 C-
3251-P1 27 W21A-22-6/BLK 9811-P2 D-
3251-P1 28 W21A-22-6/WHT 9811-P2 E-
3251-P1 29 W21A-22-6/RED 9811-P2 F-
(4) Tape and stow connector end 3251-P1 wire pins 27, 28, 29, 34, 35, 36 and
shield pigtail and connector end 9811-P2 wire pins A, B, C, D, E, F and shield
pigtail for future use.
NOTE: Do not damage or cut wire pins as they will be used for future
re-installation.

### Page 11

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 9 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
(5) Before installation of the new cable assemblies, do continuity and resistance
checks between the connector pins with an ohmmeter to verify compliance with
the schematic wiring view shown on drawing 8Z9652, POST CONDITION NEW
WIRING.
NOTE: Continuity of a circuit is affected when a resistor is part of a circuit. When
checking continuity across a resistor the value of the resistor must be
observed. Per dwg 8Z9652, resistors R2 and R3 are at 2 megaohms +/-
1% tolerance.
(6) If the resistance exceeds 5 ohms from point to point (open circuit), recheck the
new and reworked wiring to make sure it is terminated to the correct connection,
check the wiring for mechanical damage, loose connector parts, bent pins and
corrosion. Correct the deficiency.
(7) Prior to installation of the new cable assemblies do an electrical continuity
measurement from shield pigtail at 9811-P2 to shield pigtail at 3251-P1 using a
low resistance digital multimeter (four wire bonding meter). Reading should be
less than 100 milliohms. If the reading exceeds 100 milliohms check the shield
continuity across shield splices of the wire.
(8) Insert new cable assembly pins to appropriate connector ends (refer to Figures
2 and 4 and applicable instructions in WDM 20-12-10-201).
NOTE: The individual wire shields are grounded by placing the jumper wire from
the solder sleeves, around the grounding adaptor ring of the backshell
per WDM 20-15-10-401.
(9) Reinstall clamps, tie wraps and straps as necessary to secure the wiring
harnesses (refer to applicable instructions in WDM 20-12-10-201).
NOTE: It is acceptable to increase clamp size to accommodate new cable
assemblies. Do not tie wrap or clamp over the middle of resistors R2 and
R3 due to longer flexible tube and make sure the splices are placed
against rigid surface or area. It is permissible to have end of tube under
clamp.

### Page 12

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 10 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
(10) After installation, do continuity and resistance checks of the wire harnesses
between connector ends 3251-P1 and 9811-P2 with an ohmmeter to verify
compliance with the schematic wiring view shown on Figure 4, POST
CONDITION NEW WIRING.
NOTE: Continuity of a circuit is affected when a resistor is part of a circuit. When
checking continuity across a resistor the value of the resistor must be
observed. Per dwg 8Z9652, resistors R2 and R3 are at 2 megaohms +/-
1% tolerance.
(11) If the resistance exceeds 5 ohms from point to point (open circuit), recheck the
new and reworked wiring to make sure it is terminated to the correct connection,
check the wiring for mechanical damage, loose connector parts, bent pins and
corrosion. Correct the deficiency.
C. Close Out
(1) Do the functional test (open circuit test) of the nose wheel steering control
system in accordance with the instructions given in drawing 8Z9652.
(2) If removed, install the flight crew oxygen cylinder (refer to AMM TASK
35-11-01-400-801 or TASK 35-11-01-400-802).
(3) Install access panels 112AR and 122AR (refer to AMM TASK 06-41-00-992-801
for locations and to AMM TASK 53-11-00-400-801 for applicable instructions).
(4) Remove all tools and equipment from the work area.
(5) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.

### Page 13

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 11 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
Area of Retrofit
Figure 1

### Page 14

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 12 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
8Z9652-013
8Z9652-011
Area of Retrofit
Figure 2

### Page 15

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 13 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
Existing Wiring Diagram
Figure 3
NOTE: This Figure was taken from Drawing 8Z9652. Refer to the drawing
for additional details.

### Page 16

SERVICE BULLETIN 84-32-122
S.B. 84-32-122
Page 14 of 14
28 Aug 2013
NB
Revision ‘A’ 04 Oct 2013
New Wiring Diagram
Figure 4
NOTE: This Figure was taken from Drawing 8Z9652. Refer to the drawing
for additional details.

### Page 17

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 18

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
