# Bombardier Service Bulletin 84-32-140

Copy: Revision B ("84-32-140B"), 14 pages: PDF https://openairdocs.org/files/sha256/ce/99/ce99c270efca8859907c8205f76ba4299c28d4acb80c200bba748e194a256782; text https://openairdocs.org/service-documents/bombardier/sb-84-32-140/file/ce99c270efca.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2020-0975; AD 2021-11-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-32-140
- Latest revision known: 84-32-140, Revision B, dated January 30, 2018 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-32-140

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-11-04](https://openairdocs.org/ad/2021-11-04.md), effective Jul 9, 2021: Revisions A and B

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-32-140/proposed.md).

## Text (14 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2020-0975; AD 2021-11-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T x L t r S B 8 4 --- 3 2 --- 1 4 0
Page 1 of 2
Revision ‘B’ 30 Jan 2018
NB
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
Landing Gear - - - MLG Downlock Stabilizer Brace Lock Link Rigging Change to
Address MLG Unintended Unlocking - - - ModSum 4- - - 903379
This page transmits Revision ‘B’ of Service Bulletin 84- - -32- - -140, pages 1 thru 10,
dated 30 Jan 2018.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- t h eEffectivity section is revised to show that the SB is also applicable on aircraft
without PSEU 30145- - -0602 installed
--- t h eCompliance section is revised to add the Transport Canada AD number
--- t h eReferences section is revised to convey the latest revision of the service
bulletin and add the Transport Canada Airworthiness AD number.
The Compliance in the previous issue(s) of this service bulletin is not affected by
this revision. No additional rework to the aircraft is introduced by this revision.
Remove the previous revision of Service Bulletin 84- - -32- - -140 and attached VSB,
and replace with attached.
Previous issue(s) of Service Bulletin 84- - -32- - -140:
Initial issue - - - Pages 1 thru 10 dated 05 Aug 2016
Revision ‘A’ - - - Pages 1 thru 10 dated 12 Jun 2017

### Page 2

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
T x L t r S B 8 4 --- 3 2 --- 1 4 0
Page 2 of 2
Revision ‘B’ 30 Jan 2018
NB
This Page Intentionally Blank
1

### Page 3

D
S.B. 84- - -32- - -140
Page 1 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 3211 NUMBER: 84- - -32- - -140
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Landing Gear - - - MLG Downlock Stabilizer Brace Lock Link Rigging
Change to Address MLG Unintended Unlocking - - - ModSum 4- - - 903379
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4001 and
4003 thru 4534 without PSEU 30145- - -0601 or 30145- - -0602
installed and with any of the MLG brace stabilizer assemblies
that follow installed:
P/N 46400- - -15 P/N 46400- - -25
P/N 46400- - -17 P/N 46400- - -27
P/N 46400- - -21 P/N 46400- - -29
P/N 46400- - -23
Spares Affected:
None

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 2 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
B. Reason
Problem: Cases of main landing gear fold ing soon after landing with the three gear
indicating down and locked have been reported.
Cause: Upon investigation, it was found that the folding of the landing gear was
the result of extreme vibration levels. These vibrations are subsequently
transferred through the landing gear resulting in movement in the
horizontal brace where the MLG downlock sensors and downlock actuator
are located. The sensors see a “false reading” (FAR) condition and the
Solenoid Sequence Valve (SSV) removes hydraulic pressure from the
downlock actuator.
After further investigation, it was determined that the new Lock Link
overcenter dimension introduced by Service Bulletins 84- - -32- - -112 (VSB
46400- - -32- - -102) or 84- - -32- - -120 (VSB 46400- - -32- - -109) may have
contributed to the inadvertent landing gear unlocking when impacting
foreign objects or encountering excessive vibration levels and downlock
sensor reading low inductance when in NEAR position.
Solution: This service bulletin introduces ModSum 4- - -903379. The modsum
reworks the stabilizer brace assembly thru Goodrich service bulletin
46400- - -32- - -127 to reduce the lock link overcenter and to rig the downlock
sensors to smaller target gaps.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - nose landing gear lock is engaged
- - - main landing gear doors are opened and locked
- - - main landing gear lock pins are installed thru each main gear
- - - hydraulic pressure system is depleted
- - - aircraft electrical power is removed
- - - aircraft is lifted on jacks
- - - work platforms or ladders are positioned as required to gain access to the stabilizer
brace in the No. 1 and/or No. 2 wheel well and properly grounded
- - - main landing gear lock pins are removed

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 3 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
- - - the proximity sensors are loosened and backed out
- - - MLG Stabilizer Brace Assembly is reworked per Goodrich Service Bulletin
- - - the proximity sensors are pushed in and tightened
- - - rigging and inductance value check of the proximity sensors are done
- - - retraction and extension of landing gear is done
- - - aircraft is lowered from jacks
- - - close out.
D. Compliance
Bombardier Inc. highly recommend incorporation of ModSum 4- - -903379 at the
earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
Transport Canada Airworthiness Directive CF- - -2016- - -31R1 has been issued.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
# 9 3 --- Q --- 0 2 .
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F. M a n p o w e r
It will take an estimated 5.50/6.50* man- - -ho urs to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 2.00
Procedure 1.00/2.00*
T e s t/R T S 2.00
Close- - -Out 0.50

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 4 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
* I fs t o ps h i mi sr e p l a c e d .
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure tim e, part fabrication, tool acquisition or lost
time.
G. Material - - - Price and Availability
Refer to the attached Goodrich Service Bulletin 46400- - -32- - -127.
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected
K. Publications Affected
Aircraft Maintenance Manual PSM 1- - -84- - -2.........................
ModSums Manual PSM 1- - -84- - -12..................................
L. References
Revision ‘B’ of this service bulletin was prepared to the related data that follows:
ModSum 4N903379 Rev. ‘D’
ModSum 4- - -903379 Rev. ‘F’
ModSum 4N168092 Rev. ‘B’
ModSum 4N126651 Rev. ‘C’
ModSum 4N168128 Rev. ‘A’

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 5 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
Goodrich Service Bulletin 46400- - -32- - -127 dated Jul 25/16
Transport Canada Airworthiness Directive CF- - -2016- - -31R1
PCA 46055 Revision 0 (for internal reference only)
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
Refer to the attached Goodrich Service Bulletin 46400- - -32- - -127.
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None
D. Existing Parts Accountability
Refer to the attached Goodrich Service Bulletin 46400- - -32- - -127.
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of Bombardier in the CRC at
1- - -844- - -272- - -2720 (1- - -844- - -CRC- - -CRC0) or email at thd.qseries@aero.bombardier.com
for analysis and to get an approved disposition to complete this service bulletin.
A . J o b S e t --- U p
(1) Engage the nose gear ground lock (refer to AMM TASK 10- - -11- - -00- - -400- - -801).
(2) Open and lock the main landing gear doors (refer to applicable instructions in
AMM TASK 32- - -00- - -00- - -840- - -801).
(3) Install the lock pins on the main landing gear (refer to AMM TASK
10- - -11- - -00- - -400- - -802).

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 6 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
(4) Deplete all hydraulic pressure in the No. 1, No. 2 and No. 3 system (refer to
AMM TASK 29- - -00- - -00- - -863- - -802 and TASK 29- - -00- - -00- - -863- - -804).
(5) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(6) Install a warning sign on the external hydraulic connection.
(7) Install a warning sign on the hydraulic PTU Control Switch (on main instrument
panel).
(8) Lift the aircraft on jacks (refer to AMM TASK 07- - -10- - -00- - -582- - -801).
(9) Set up the work platforms or ladders as required to gain access to main landing
gear stabilizer brace assemblies. Make sure the work platforms or ladders are
electrically grounded.
(10) Remove the lock pins on the main landing gear (refer to AMM TASK
10- - -11- - -00- - -000- - -802).
B. Procedure
WARNING: MAKE SURE THAT THERE IS NO PRESSURE IN THE HYDRAULIC
SYSTEM. IF YOU DO NOT DO THIS YOU CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT .
(1) Loosen and back out the proximity sensors LGDLK1/2 (RGDLK1/2) (refer to
Figure 1 and to applicable instructions in AMM TASK 32- - -61- - -06- - -000- - -802).
NOTE: Do not remove the proximity sensors.
(2) Push up at the apex of the forward and aft link assemblies to break the
overcenter lock position.
(3) Rework the MLG stabilizer brace assembly to agree with all of the details given
in the attached Goodrich Service Bulletin 46400- - -32- - -127.
(4) Push in and tighten the proximity sensors LGDLK1/2 (RGDLK1/2) (refer to Figure
1 and to applicable instructions in AMM TASK 32- - -61- - -06- - -400- - -802).

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 7 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
(5) Check the gap of the LH and RH MLG downlock proximity sensors LGDLK1,
LGDLK2, RGDLK1 and RGDLK2 (Refer to Figure 1). The gap should be 0.035 to
0.040 inch.
(6) If the sensor gap is not within 0.035 to 0.040 inch, adjust the gap to 0.035 to
0.040 inch (refer to the applicable instructions in AMM TASK
32- - -61- - -06- - -830- - -801).
(7) Do a check of the the inductance of the proximity sensors (refer to the applicable
instructions in AMM TASK 32- - -61- - -00- - -280- - -801).
(8) If the inductance exceeds 8.522 mH, incrementally increase the target gap to
bring the inductance to 8.522- - -8.422mH range. Make sure that the resultant
sensor gap is not more than 0.045 inch.
(9) Do a retraction and extension of the landing gear (refer to AMM TASK
32- - -31- - -00- - -867- - -801).
(10) Do a visual check to see that the main landing gear is fully retracted. Make sure
that nothing hangs loose, binds or touches the other components. Make sure
that there is sufficient clearance aro und all the components especially between
the A- - -Frame and Stabilizer Brace and the doors are fully closed.
(11) Make sure to re- - -identify the stabili zer brace assembly nameplate as described
in the attached Goodrich Service Bulletin 46400- - -32- - -127 using the vibropeen
method.
(12) Repeat above steps (1) to (11) to do the rework on opposite MLG stabilizer
brace.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) Lower the aircraft from the jacks (refer to AMM TASK 07- - -10- - -00- - -582- - -801).
(3) Unlock and close the landing gear doors (refer to AMM TASK
3 2 --- 0 0 --- 0 0 --- 8 4 0 --- 8 0 2 ) .

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 8 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
(4) On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applic able logbook(s). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.

### Page 11 (OCR)

SERVICE BULLETIN 84-32-140
10  LEmo
— 13
-20
LEGEND
1. Hydraulic hose.
2. Hydraulic hose.
3. Lock actuator.
10. Stabilizer brace.
21  13. Downlock proximity sensor.
14. Downlock proximity sensor.
20. Harness assembly.
21. Harness assembly.
25. Bonding jumper.
31. Forward lock link assembly.
32. Aft lock link assembly.
13
14
20
21 32
MLG Stabilizer Brace
Figure 1
05 Aug 2016  S.B. 84-32-140
Revision 'B' 30 Jan 2018  Page 9 of 10
NB

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 0
S.B. 84- - -32- - -140
Page 10 of 10
05 Aug 2016
NB
Revision ‘B’ 30 Jan 2018
This Page Intentionally Blank
1

### Page 13

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 14

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
