# Bombardier Service Bulletin 84-32-142

Copy: No revision named ("SB 84-32-142"), 10 pages: PDF https://openairdocs.org/files/sha256/07/c9/07c9b6141d89b3953c03da11dc79803cd8212b1364d7277a545ca83e56ad0913; text https://openairdocs.org/service-documents/bombardier/sb-84-32-142/file/07c9b6141d89.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2016-7422; AD 2016-13-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-32-142
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-32-142

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2017-23-01](https://openairdocs.org/ad/2017-23-01.md), effective Dec 19, 2017: No revision named
- [AD 2016-13-14](https://openairdocs.org/ad/2016-13-14.md), effective Jul 20, 2016: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-32-142/proposed.md).

## Text (10 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2016-7422; AD 2016-13-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

D
S.B. 84- - -32- - -142
Page 1 of 10
04 May 2016
MG
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 3231 NUMBER: 84- - -32- - -142
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Landing Gear - - - Primary Extension and Retraction - - - MLG Retraction
Actuator Rod End Cracking - - - Special Inspection and Rectification
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4325.
Spares Affected:
Bombardier Inc. DHC- - -8- - -400 Series, Models - - -400, - - -401 and - - -402,
equipped with MLG Retract Actuator Rod End P/N P3A2750 or P3A2750- - -1.
B. Reason
Problem: Cracks may be found on the rod end of the MLG retraction actuator.

### Page 2

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 2 of 10
04 May 2016
MG
Solution: Do an inspection of the rod end of the MLG retraction actuator for the
affected part number. If the part number is found, do a fluorescent dye
penetrant inspection on the rod end for cracks. Replace the rod end if
cracks are found.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - a record search is done to determine if the part number of the rod ends of the MLG
retraction actuators is P3A6460
- - - if the record search cannot determine that the part number of the rod ends are
P3A6460, a visual inspection of the rod ends is done. No further action is required if
rod ends P3A6460 are installed
- - - if a visual inspection has to be done, aircraft electrical power is removed
- - - the nose landing gear lock is engaged
- - - the main landing gear lock pins are installed thru each main gear and main gear door
mechanism
- - - access is gained to the main landing gear retraction actuator in the left and right hand
nacelles
- - - the rod ends are disconnected at the shock strut and a fluorescent dye penetrant
inspection is done on the rod ends for cracks
- - - the rod ends are replaced before next flight if cracks are found
- - - an operational test of the MLG is done if any of the rod ends have been replaced
- - - close out.
D. Compliance
Bombardier Inc. highly recommend that this special inspection and rectification
service bulletin be incorporated at the earliest opportunity unless otherwise directed
by the operator’s airworthiness authority.
A Transport Canada Airworthiness Directive Pending.

### Page 3

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 3 of 10
04 May 2016
MG
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
# 9 3 --- Q --- 0 2 .
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F. M a n p o w e r
It will take an estimated 3.00 man- - -hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.25
Procedure 2.00
T e s t/R T S 0.50
Close- - -Out 0.25
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure tim e, part fabrication, tool acquisition or lost
time.
G. Material - - - Price and Availability
None
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 4 of 10
04 May 2016
MG
K. Publications Affected
ModSum Manual PSM 1- - -84- - -12...................................
L. References
The initial issue of this service bulletin was prepared to the engineering drawings and
related data that follows:
B o m b a r d i e r S e r v i c e B u l l e t i n 8 4 --- 3 2 --- 8 2
PCA 46233 Revision 0 (for internal reference only)
Transport Canada Airworthiness Directive Pending.
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) The following material(s) are required for the completion of this service bulletin
and may be procured as single items from Bombardier Aerospace Regional
Aircraft or purchased directly from industry sources.
Each consumable product listed in the table below is given its own unique
Product ID Number. The number is used to identify a particular recommended
product, the specifications and the trade names any of which can be used
unless specified otherwise (refer to PSM 1- - -84- - -18 Consumable Products
Manual).
Consumable
Product ID
Number
Qty. Per
Aircraft
Description
04- - -03 A/R Synthetic Grease
05- - -16 A/R Putty, General Purpose, Non- - -Hardening
07- - -01A A/R F13 Coating- - -Compound, Corrosion Preventative
14- - -06 AR Lockwire- - -0.032 in. (0.8mm)
14- - -143 A/R Ta p e , P r o t e c t i v e

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 5 of 10
04 May 2016
MG
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None
D. Existing Parts Accountability
None
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
(1) Do a record search for evidence that rod end P3A6460 is installed on the left and
right hand MLG retraction actuators. No further action is required if rod end
P3A6460 is installed on both sides, go to C. Close Out .
(2) If the record search does not find evidence of rod end P3A6460 being installed
on both sides, refer to the steps that follow and do a visual inspection of the rod
end.
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 6 of 10
04 May 2016
MG
(3) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K ’ S 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(4) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(5) Make sure the nose gear ground lock is engaged.
(6) Set wheel chocks in front and behind the landing gear tires.
(7) Refer to Figure 1 and set up the work platforms or ladders as required to gain
access to the main landing gear (MLG) retraction actuator located in the left and
right hand nacelle. Make sure the work platforms or ladders are electrically
grounded.
B. Procedure
(1) Refer to Figure 1, Figure 2 and do a visual inspection on the rod end of the MLG
retraction actuator for evidence of p art number ‘P3A6460’ stamped on the rod
end. No further action is required if part number ‘P3A6460’ is found.
(2) If rod end ‘P3A6460’ is not installed, repeat the visual inspection on the rod end
of the MLG retraction actuator for the opposite nacelle. No further action is
required if part number ‘P3A6460’ is found.
(3) If part number ‘P3A6460’ is not installed, refer to the steps below and do the
fluorescent dye penetrant inspection on the rod end for cracks.
( a ) R e f e r t o t h e a p p l i c a b l e s t e p s i n A M M T A S K 3 2 --- 3 1 --- 1 1 --- 0 0 0 --- 8 0 1 a n d
disconnect the rod end from the shock strut.
NOTE: If a fluorescent dye penetrant inspection is done, make sure the
threads, jam nut and rod end bearing are masked for protection.
(b) Refer to Figure 3 and Nondestructive T esting Manual PSM 1- - -84- - -7A, TASK
51- - -00- - -01- - -230- - -801 and do a fluorescent dye penetrant inspection on the
rod end for cracks. If cracks are not found, refer to the applicable steps in AMM
TASK 32- - -31- - -11- - -400- - -801 and connect the rod end to the shock strut..

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 7 of 10
04 May 2016
MG
(c) If cracks are found, refer to AMM TASK 07- - -10- - -00- - -582- - -801 and put the
aircraft on jacks. Refer to AMM TASK 32- - -31- - -11- - -000- - -803, TASK
3 2 --- 3 1 --- 1 1 --- 4 0 0 --- 8 0 3 a n d r e p l a c e t h e r o d e n d b e f o r e n e x t f l i g h t .
(4) Repeat steps B.(3)(a) thru B.(3)(c) for the opposite MLG if part number ‘P3A6460’
was not installed.
C. Close Out
(1) If the record search confirmed that rod end P3A6460 was installed on the MLG
retraction actuators of both nacelles, go to step C.(5).
( 2 ) I f a n y o f t h e r o d e n d ( s ) w e r e r e p l a c e d , r e f e r t o A M M T A S K 3 2 --- 3 1 --- 0 0 --- 7 1 0 --- 8 0 1
and do an operational test of the main landing gear.
(3) If the aircraft was placed on jacks, refer to AMM TASK 07- - -10- - -00- - -582- - -801 and
lower the aircraft and remove the jacks.
(4) Remove all tools and equipment from the work area.
(5) On incorporation of this special inspection and rectification service bulletin, make
an entry that conforms to local regula tory requirements in the applicable
logbook(s). Enter component serial numbers if applicable. Enter this ModSum
number only after complete and functional incorporation of all work defined in
this service bulletin.

### Page 8 (OCR)

SERVICE BULLETIN 84-32-142
MLG RETRACTION
ACTUATOR
ROD END
(SEE FIGURE 2)
Location of MLG Retraction Actuator - Rod End
Figure 1
04 May 2016  S.B. 84-32-142
Page 8 of 10
MG

### Page 9 (OCR)

SERVICE BULLETIN 84-32-142
57605-8196469
PART NUMBER
Location of Part Number on Rod End
Figure 2
04 May 2016  S.B. 84-32-142
Page 9 of 10
MG

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 3 2 --- 1 4 2
S.B. 84- - -32- - -142
Page 10 of 10
04 May 2016
MG
Location on Rod End - - - Crack Inspection
Figure 3
LOCATION ON
ROD END TO BE
INSPECTED FOR
CRACKS
ON BOTH SIDES
ON BOTH SIDES
1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
