# De Havilland Canada Service Bulletin 84-32-164

Copy: Revision A ("SB 84-32-164A"), 17 pages: PDF https://openairdocs.org/files/sha256/7e/d0/7ed0acde0ba4163e0a1ac8b50738cee52f3ff511625156be4fb28510fd20bad9; text https://openairdocs.org/service-documents/bombardier/sb-84-32-164/file/7ed0acde0ba4.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0394; AD 2022-13-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md) (issued as De Havilland Canada)
- Type: Service bulletin (Service Bulletin)
- Number: 84-32-164
- Latest revision known: 84-32-164, Revision A, dated May 13, 2021 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-32-164

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2022-13-08](https://openairdocs.org/ad/2022-13-08.md), effective Aug 10, 2022: Revision A

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-32-164/proposed.md).

## Text (17 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0394; AD 2022-13-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Tx Ltr SB 84- - - 32- - - 164
P a g e1o f2
Revision ‘A’ 13 May 2021
JV
DHC - - -8 (DASH 8)
SERVICE BULLETIN 84 - - -32 - - -164
L a n d i n g G e a r --- N o s e W h e e l S t e e r i n g --- H y d r a u l i c M o t o r --- L o s s o f
Configuration Control - - - Motor Jam due to Wear - - -ModSum 4 - - -114018
This page transmits Revision ‘A’ of Service Bulletin 84- - - 32- - - 164, pages 1 thru 8,
dated 13 May 2021.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- T h eReference section is revised to convey the latest revision of the service
bulletin and engineering documentation.
- - - Revised theDescription, Manpower , Job Set- - -Upand Procedure sections.
The Compliance in the previous issue of this service bulletin is not affected by this
revision. No additional rework to the aircraft is introduced by this revision.
Remove the initial issue of Service Bulletin 84- - -32- - -164 and replace with attached.
Previous issue of Service Bulletin 84- - - 32- - - 164:
Initial issue - - - Pages 1 thru 8 dated 20 Apr 2020
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 1 of 17

### Page 2

SERVICE BULLETIN 84- - -32- - -164
Tx Ltr SB 84- - - 32- - - 164
P a g e2o f2
Revision ‘A’ 13 May 2021
JV
This Page Intentionally Blank
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 2 of 17

### Page 3

S.B. 84- - - 32- - - 164
P a g e1o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
SERVICE BULLETIN
ATA SYSTEM: 3221 NUMBER: 84- - -32- - -164
DE HAVILLAND AIRCRAFT OF CANADA LIMITED (DHC) CONSIDERS
THIS SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT : Landing Gear - - - Nose Wheel Steering - - - Hydraulic Motor - - - Loss of
Configuration Control - - - Motor Jam due to Wear - - - ModSum 4 - - -114018
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC - - - 8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4622.
Related ModSum Title
4N114018 Landing Gear - - - Nose Wheel Steering - - - Hydraulic
Motor - - - Loss of Configuration Control - - - Motor
Jam due to Wear
Production: ModSum 4- - - 114018 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4623 and
subsequent.
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 3 of 17

### Page 4

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e2o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery on the aircraft or as
changed by DHC Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this
bulletin can be completed.
Spares Affected:
Refer to the enclosed UTC Aerospace Systems Service Bulletin
47200- - - 32- - - 146
B. Reason
Problem: De Havilland Aircraft of Canada Limited has identified a condition that
could lead to loss of aircraft directional control and runway excursion. The
nosewheel steering hydraulic motor piston rod shoes can wear and with
sufficient wear , can compromise the piston shoe retention feature and
dislodge when exposed to sufficient case pressure resulting in a jammed
condition.
The motor supplier initiated a change in shoe design on the RS1267
steering motor to improve retention and prevent wear . The supplier did not
change the part number of the motor during this product improvement.
Solution: This service bulletin provides the instructions to do an inspection of the
nose wheel steering motor serial number. The discrepant serial number
range is specified in the enclosed UTC Aerospace Systems Service
Bulletin 47200- - - 32- - - 146. If the motor serial number falls within the
discrepant range it will be removed and replaced with a RS1267- - -5 motor.
If the motor serial number falls outside the discrepant range it will be
re- - - labeled as RS1267- - - 5 motor. The incorporation of the RS1267- - - 5
motor will roll the part numbers of the gearbox assembly and the dressed
shock strut assembly as per the enclosed UTC Aerospace Systems
Service Bulletin 47200- - - 32- - - 146.
This service bulletin also introduces a new steering motor P/N RS1267- - - 5
to prevent the steering motor jam and restores configuration control.
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 4 of 17

### Page 5

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e3o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - Aircraft electrical power is removed
- - - The Nose Landing Gear (NLG) lock is engaged
- - - The Main Landing Gear (MLG) lock pins are installed thru each main gear and main
gear door mechanism
- - - Jacking of the NLG
- - - Remove the NLG Aft Doors connecting rods
- - - Retract the NLG
- - - Identify the steering motor part number and serial number on the nameplate
- - - if the steering motor part number and serial number is on the list in Section 1A, Part
A of VSB 47200- - - 32- - - 146, or serial number is 379 and subsequent, re- - - identify the
steering motor and extend the NLG
- - - If the steering motor part number or serial number are not in the list in Section 1A, Part
A of VSB 47200- - - 32- - - 146, the motor must be removed
- - - Extend the NLG via the Alternate extension
- - - Remove the steering motor and return to Collins Customer Services for corrective
action
- - - Install a new steering motor
- - - Retract the NLG
- - - Re- - -identify the gearbox assembly and dressed shock strut assembly
- - - Extend the NLG via the Alternate extension
- - - Install the NLG Aft Doors connecting rods
- - - Lower the Aircraft
- - - The operational test of the nose wheel steering system is done
- - - Close out.
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 5 of 17

### Page 6

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e4o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
D. Compliance
De Havilland Aircraft of Canada Limited highly recommends that ModSum 4- - - 114018
be incorporated at the earliest opportunity unless otherwise directed by the operator’s
airworthiness authority.
A Transport Canada Airworthiness Directive Pending.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
#19- - - Q - - - 01.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F . Manpower
It will take an estimated 7.00 man- - -hours to complete this service bulletin without the
replacement of the steering motor. The breakdown of the man- - -hours is shown in the
table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 3.00
Procedure 3.00
T e s t/R T S 0.00
Close- - -Out 1.00
It will take an estimated 11.00 man- - -hours to complete this service bulletin with the
replacement of the steering motor. The breakdown of the man- - -hours is shown in the
table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 3.00
Procedure 6.00
T e s t/R T S 1.00
Close- - -Out 1.00
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 6 of 17

### Page 7

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e5o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure time, part fabrication, tool acquisition or lost
time.
G. Material - - - Price and Availability
Refer to the enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146.
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected
K. Publications Affected
Aircraft Illustrated Parts Catalog P S M 1 --- 8 4 --- 4......................
ModSums Manual P S M 1 --- 8 4 --- 1 2..................................
L. References
Revision ’A’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
83220400 1 AN
ModSum 4- - - 114018 Rev. ‘C’
PCA 47618 Revision 1 (for internal reference only)
ADR SHAR- - - 20- - - 22540933 (for internal reference only)
ADR ALAC - - - 20- - - 29441010 (for internal reference only)
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 7 of 17

### Page 8

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e6o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
Transport Canada Airworthiness Directive Pending
UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146 dated Mar 30/2020.
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
Refer to the enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146.
B. Parts Required to Modify Spares
Refer to the enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146.
C. Special T ools and Equipment Required
None
D. Existing Parts Accountability
Refer to the enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146.
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of DHC in the CRC at 1 (844)
272- - - 2720 (1 (844) CRC - - - CRC0) or email at thd@dehavilland.comfor analysis and to get an
approved disposition to complete this service bulletin.
A . J o b S e t --- U p
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 8 of 17

### Page 9

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e7o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK 24- - - 00- - - 00- - - 861- - - 802 and TASK
24- - - 00- - - 00- - - 910- - - 801).
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set wheel chocks in front and behind the landing gear tires.
(5) Jack the aircraft at the NLG using the fuselage jacking point. (refer to the
applicable instructions in AMM TASK 07- - - 10- - - 00- - - 582- - - 801).
B. Procedure
(1) Remove the NLG Aft Doors connecting rods only at the shock strut and secure
the doors from damage (refer to AMM TASK 32- - - 22- - - 06- - - 000- - - 801)
(2) Retract the NLG. (refer to the applicable instructions in AMM TASK
32- - - 31- - - 00- - - 867- - - 802).
(3) Identify the steering motor part number and serial number as noted on the
nameplate and do the applicable steps that follow:
(a) If the steering motor part number and serial number is on the list in
Section 1A, Part A of VSB 47200- - - 32- - - 146, or serial number is 379 and
subsequent, re- - -identify the steering motor from P/N RS1267- - -3 to P/N
RS1267- - - 5 by replacing the label in situ. While the NLG is in the up and
locked position with doors disconnected, re- - -identify the gearbox and
shock strut assembly (refer to the enclosed UTC Aerospace Systems
service bulletin 47200- - - 32- - - 146), proceed to step 10.
(b) If the steering motor part number or serial number is not in Section 1A, Part
A of VSB 47200- - - 32- - - 146, it must be removed, while the NLG is in the up
and locked position with doors disconnected remove the cotter pin on the
lower bolt of the steering motor and proceed to step 4 (this cotter pin is
hard to access when the gear is extended).
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 9 of 17

### Page 10

SERVICE BULLETIN 84- - -32- - -164
S.B. 84- - - 32- - - 164
P a g e8o f8
JV
20 Apr 2020
Revision ’A’ 13 May 2021
(4) Extend the NLG via the Alternate extension (refer to AMM TASK
32- - - 31- - - 00- - - 867- - - 802).
(5) Remove the steering motor (refer to AMM TASK 32- - - 51- - - 31- - - 000- - - 801) and
return it to Collins - - - Customer Services for corrective action (refer to the
enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146)
(6) Install the new steering motor P/N RS1267- - -5 (refer to AMM TASK
32- - - 51- - - 31- - - 400- - - 801).
(7) Retract the NLG. (refer to the applicable instructions in AMM TASK
32- - - 31- - - 00- - - 867- - - 802).
(8) Install the cotter pin that was removed in step 3 (b).
(9) Re- - -identify the gearbox assembly and dressed shock strut assembly (refer to the
enclosed UTC Aerospace Systems Service Bulletin 47200- - - 32- - - 146).
NOTE: T o re- - -identify the gearbox assembly and dressed shock strut the NLG
must be in the retracted position.
(10) Extend the NLG via the Alternate extension (refer to AMM TASK
32- - - 31- - - 00- - - 867- - - 802).
(11) Install the NLG Aft Doors connecting rods (refer to the AMM TASK
32- - - 22- - - 06- - - 400- - - 801)
(12) Do the operational test of the nose wheel steering system (refer to AMM TASK
32- - - 51- - - 00- - - 710- - - 801), if the steering motor was replaced.
(13) Do the Close Out.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum make an entry that conforms to local regulatory
requirements in the applicable logbook(s). If only part of this ModSum is
completed, use only this service bulletin number as reference and detail exact
limit of work completed. Enter component serial numbers if applicable. Enter this
ModSum number only after complete and functional incorporation of all work
defined in this service bulletin.
1
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 10 of 17

### Page 11

Landing Systems - Landing Gear
Goodrich Aerospace Canada Ltd 
1400 South Service Road West 
Oakville, Ontario L6L 5Y7 
Canada  
Tel: +1 905 825 1515 
Fax: +1 905 825 1583 
www.customers.utcaerospacesystems.com 
CAGE: 02121
SERVICE BULLETIN
Page 1 of 7
Mar 30/20
EXPORT CLASSIFICATION
U.S. Export Classification: EAR ECCN - 9E991   EIPA Export Classification: NSCanR
PROPRIETARY INFORMATION
THIS DOCUMENT IS THE PROPERTY OF UTC AEROSPACE SYSTEMS. YOU MAY NOT POSSESS, USE, COPY OR DISCLOSE THIS DOCUMENT OR ANY 
INFORMATION IN IT, FOR ANY PURPOSE, INCLUDING WITHOUT LIMITATION, TO DESIGN, MANUFACTURE OR REPAIR PARTS, OR OBTAIN ANY 
GOVERNMENT APPROVAL TO DO SO, WITHOUT UTC AEROSPACE SYSTEM'S EXPRESS WRITTEN PERMISSION. NEITHER RECEIPT NOR POSSESSION OF 
THIS DOCUMENT ALONE, FROM ANY SOURCE, CONSTITUTES SUCH PERMISSION. POSSESSION, USE, COPYING OR DISCLOSURE BY ANYONE WITHOUT 
UTC AEROSPACE SYSTEM'S EXPRESS WRITTEN PERMISSION IS NOT AUTHORIZED AND MAY RESULT IN CRIMINAL AND/OR CIVIL LIABILITY.
47200-32-146
LANDING GEAR - NOSE WHEEL STEERING - HYDRAULIC MOTOR – LOSS OF 
CONFIGURATION CONTROL - MOTOR JAM DUE TO WEAR
1. PLANNING INFORMATION
A. Effectivity
Part A
All Dressed NLG Shock Strut Assemblies with steering motor PN RS1267-3 serial 
numbers 379 and Sub installed or the following serial number motors which have been 
upgraded during shop visit:
49W2T 49W4D 49W4W 081021 0160 0219 0296 0343
49W3L 49W4F 49W4Y 0084 0167 0223 0300 0348
49W3M 49W4G KX97D 0097 0169 0247 0307 0357
49W3N 49W4J KX97H 0103 0170 0255 0317 0364
49W3P 49W4K KX9WU 0110 0171 0260 0321 0370
49W3R 49W4L 0008 0114 0175 0276 0326 0371
49W3T 49W4M 0041 0141 0176 0277 0327
49W3W 49W4P 0062 0145 0185 0278 0329
49W4B 49W4R 0072 0152 0198 0281 0331
49W4C 49W4T 0073 0157 0203 0285 0340
 
Part B
All Dressed NLG Shock Strut Assemblies with steering motor PN RS1267-1, RS1267-1 
MOD SB 32-13, RS1267-2, RS1267-2 MOD SB 32-13 or RS1267-3 with serial number 
not listed in Part A installed.
B. Concurrent Requirements
None.
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 11 of 17

### Page 12

Page 2/7
Mar 30/20
UTC AEROSPACE SYSTEMS PROPRIETARY 
U.S. Export Classification: EAR ECCN - 9E991 
EIPA Export Classification: NSCanR
47200-32-146
C. Reason
Part A
The motor supplier initiated a change in shoe design on the RS1267 steering motor to 
improve retention and prevent wear, Excessive wear on the shoes can lead to a motor 
jam. The supplier did not change the part number of the motor during this product 
improvement. This SB will re-identify those steering motors by serial number that need to 
be re-identified with a new part number. 
Part B
Product improvement introducing a new steering motor RS1267-5 to prevent steering 
motor jam and restores configuration control. 
D. Description
Part A
Carry out re-identification of the steering motor RS1267-3 to RS1267-5 if the motor is on 
the list of serial numbers published in this Service Bulletin, also re-identify the gearbox 
assembly and dressed shock strut assembly.
Part B
Replace all RS1267-1, RS1267-1 MOD SB 32-13, RS1267-2, RS1267-2 MOD SB 32-13 
and RS1267-3 steering motors not identified in part A with new RS1267-5 and re-identify 
the gearbox assembly and dressed shock strut assembly.  
E. Compliance
Goodrich Aerospace Canada Ltd recommends incorporation of this bulletin at operator’s 
earliest convenience.
F. Approval
The technical content of this Service Bulletin has been reviewed and accepted by De 
Havilland Aircraft of Canada Limited.
G. Manpower
NA
H. Weight and Balance
NA
I. Electrical Load Data
NA
J. Software Accomplishment Summary
Does not apply.
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 12 of 17

### Page 13

Page 3/7
Mar 30/20
UTC AEROSPACE SYSTEMS PROPRIETARY 
U.S. Export Classification: EAR ECCN - 9E991 
EIPA Export Classification: NSCanR
47200-32-146
K. References
Goodrich Landing Gear Component Maintenance Manual 32-21-04  
After Market Process Specification (AMPS) Goodrich CMM 20-00-01  
DHC Aircraft Maintenance Manual (AMM) PSM 1-84-2  
Modsum 4N114018 
Rockwell Collins SB NOSEWHEEL POWER STEERING UNIT-32-501 
Rockwell Collins SB NOSEWHEEL POWER STEERING UNIT-32-1
L. Other Publications Affected
Goodrich Landing Gear Component Maintenance Manual 32-21-04
M. Interchangeability of Parts
Steering Motor RS1267-5 replaces steering motor PN RS1267-1, RS1267-1 MOD SB 32-
13, RS1267-2, RS1267-2 MOD SB 32-13 and RS1267-3 and is one way 
interchangeable.
2. MATERIAL INFORMATION
A. Material Cost & Availability
Part A Nameplate PN CW30-101014-1 is a available FOC from:
Collins - Customer Services 
1400 South Service Road  
Oakville, ON,  
L6L5Y7  
Canada
Part B Hydraulic motor PN RS1267-1, RS1267-1 MOD SB 32-13, RS1267-2, RS1267-2 
MOD SB 32-13 and RS1267-3 is returned for FOC upgrade to:
Collins - Customer Services 
4115 Corporate Center Drive  
Monroe, NC,  
28119-1313  
USA
B. Material Required for each component
Part A
NOTE:
FIG/
ITEM 
NO
NEW PART NO.
QTY 
PER 
UNIT
KEYWORD OLD PART NO. DISPOSITION
1-30A CW30-101014-1 1 Nameplate 310089-1 Discard
Fig/Item numbers refer to figure 1 in this SB
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 13 of 17

### Page 14

Page 4/7
Mar 30/20
UTC AEROSPACE SYSTEMS PROPRIETARY 
U.S. Export Classification: EAR ECCN - 9E991 
EIPA Export Classification: NSCanR
47200-32-146
Part B
NOTE:  Fig/Item numbers refer to CMM 32-21-04 IPL Figure-Item number
FIG/
ITEM 
NO
NEW PART NO.
QTY 
PER 
UNIT
KEYWORD OLD PART NO. DISPOSITION
1-1532 RS1267-5 1 Hydraulic Motor RS1267-1, 
RS1267-1 MOD 
SB 32-13, 
RS1267-2, 
RS1267-2 MOD 
SB 32-13 and 
RS1267-3
Return to Collins 
for upgrade
1-1533 4248-0001-2 1 Jumper Cable 4248-0001-2 Reuse
1-1534 MS24665-132 2 Cotter Pin MS24665-132 Discard
1-1535 MS17825-5 2 Nut MS17825-5 Discard
1-1536 AN960-516L 2 Washer AN960-516L Reuse
1-1537 MS20002C5 4 Washer MS20002C5 Reuse
1-1538 NAS6605D15 2 Bolt NAS6605D15 Reuse
1-1539 NAS6605H8 2 Bolt NAS6605H8 Reuse
MS20995C32 AR Safety Wire MS20995C32 Discard
C. Accomplishment instructions
Part A
Procedure (Refer Figure 1)
NOTE: Item numbers in parenthesis ( ) refer to CMM 32-21-04 IPL Figure-Item number.
NOTE: Item numbers in parenthesis [ ] refer to Figure 1 of this SB.
(1) Identify the serial number on the nameplate [1-30].
(2) If serial number is within the range given in Para 1.A. Part A. do the following:
(a) Remove the nameplate PN 310089-1 [1-30] from steering motor (1-1532).
CAUTION: MAKE SURE ALL INFORMATION FROM THE OLD NAMEPLATE IS 
TRANSPOSED TO THE NEW NAMEPLATE.
(b) Install new nameplate PN CW30-101014-1 [1-30A] in the new position on to 
steering motor (1-1532), (Ref figure 1 sheet 2) (Refer to AMPS 6001 type 1).
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 14 of 17

### Page 15

Page 5/7
Mar 30/20
UTC AEROSPACE SYSTEMS PROPRIETARY 
U.S. Export Classification: EAR ECCN - 9E991 
EIPA Export Classification: NSCanR
47200-32-146
(3) If serial number is not within the range given Para 1.A. Part A. do the Part B below.
Part B (Refer Figure 1)
NOTE: Item numbers in parenthesis ( ) refer to CMM 32-21-04 IPL Figure-Item number.
NOTE: Item numbers in parenthesis [ ] refer to Figure 1 of this SB.
Procedure
(1) Identify the serial number on the nameplate [1-30].
(2) If PN’s listed are not in the serial number range given in Para 1.A. Part A. do the 
following:
(3) Remove the steering motor (1-1532), (Refer to AMM Task 32-51-31-000-801). Return 
the steering motor for upgrade to:
Collins - Customer Services 
4115 Corporate Center Drive  
Munroe, NC,  
28119-1313  
USA
(4) Install the new steering motor RS1267-5 (Refer to AMM Task 32-51-31-400-801).
3. RE-IDENTIFICATION
NOTE: Item numbers in parenthesis ( ) refer to CMM 32-21-04 IPL Fig-Item Number.
NOTE: Item numbers in parenthesis [ ] refer to Figure 1 of this SB.
NOTE: Re-identification to be carried out using the vibro engrave method (Ref. AMPS 1600).
(1) Re-identify the gearbox assembly PN 0080-0035-3 as 0080-0035-3 SB1 on nameplate 
[1-20].
(2) Re-identify the gearbox assembly PN 0080-0035-5 as 0080-0035-7 on nameplate [1-
20].
(3) Re-Identify Power Steering Unit PN 47181-3 as 47181-3A on nameplate [1-20].
(4) Re-Identify Power Steering Unit PN 47181-1003 and 47181-5 as 47181-7 on 
nameplate [1-20].
(5) Re-identify dressed shock strut 47200-33 as 47200-35 on nameplate (1-15, 1A-20).
(6) For all other dressed shock struts record the incorporation of this Service Bulletin and 
date of accomplishment on the nameplate (1-15, 1A-20).
(7) Record incorporation of this SB and date accomplished on nameplate (1-15, 1A-20).
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 15 of 17

### Page 16 (OCR)

DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146RO_MAR30/20  Page 16 of 17
UTC Aerospace Systems
NAMEPLATE
(1-15, 1A-20)
PARTIAL VIEW ON ARROW A
NAMEPLATE
[1-20]
GEARBOX
(1-1531)
DETAIL B
SE_0400_47200-32-146401
Nameplate Locations
Figure 1 (Sheet 1 of 2)
UTC AEROSPACE SYSTEMS PROPRIETARY  47200-32-146  Page 6 of 7
U.S. Export Classification: EAR ECCN - 9E991  Mar 30/20
EIPA Export Classification: NSCanR

### Page 17

Page 7 of 7
Mar 30/20
UTC AEROSPACE SYSTEMS PROPRIETARY 
U.S. Export Classification: EAR ECCN - 9E991 
EIPA Export Classification: NSCanR
47200-32-146
 
Nameplate Locations
 Figure 1 (Sheet 2 of 2)
DHC Merged Document SB84-32-164A_13 May 2021 & UTC AEROSPACE SYSTEMS VSB 47200-32-146R0_MAR30/20
Page 17 of 17

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
