# Bombardier Service Bulletin 84-54-14

Copy: Revision K ("84-54-14K"), 30 pages: PDF https://openairdocs.org/files/sha256/bd/b6/bdb63e61c957e05e01fe347ce96c25f42c14dcb2658f913407eb07f93e4fdc47; text https://openairdocs.org/service-documents/bombardier/sb-84-54-14/file/bdb63e61c957.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2020-0099; AD 2020-11-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-54-14
- Latest revision known: 84-54-14, Revision K, dated August 7, 2018 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-54-14

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2020-11-13](https://openairdocs.org/ad/2020-11-13.md), effective Jul 14, 2020: Revisions J and K
- [AD 2010-23-04](https://openairdocs.org/ad/2010-23-04.md), effective Nov 22, 2010: Revision J

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-54-14/proposed.md).

## Text (30 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2020-0099; AD 2020-11-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘K’ 07 Aug 2018
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
Nacelles - - - Rear Spar Attachment Fitting P/N 85414663- - - *** - - - Special
Inspection and Rectification
This page transmits Revision ‘K’ of Service Bulletin 84- - -54- - -14, pages 1 thru
26, dated 07 Aug 2018.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- t h eEffectivity section has been revised from ‘4001 thru 4999’ to ‘4001,
4003, 4004, 4006, 4008 thru 4380’ and to add two notes
--- t h eReason section is revised to remove reference to SB 84- - -54- - -15 and
add reference to SB 84- - -54- - -16.
--- t h eDescription section is revised to remove reference to SB 84- - -54- - -15
and add reference to SB 84- - -54- - -16.
- - - components of theCompliance section are revised to reflect the changes in
the Effectivity section. Also, an AD statement is added
--- t h eManpower section is revised to remove reference to SB 84- - -54- - -15 and
add reference to SB 84- - -54- - -16.
--- t h eReferences section is revised to convey the latest revision of the service
bulletin and engineering documentation
- - - several locations inProcedure section are revised to remove reference to
S B 8 4 --- 5 4 --- 1 5 a n d a d d r e f e r e n c e t o S B 8 4 --- 5 4 --- 1 6 f o r f i t t i n g r e p l a c e m e n t
--- t h eClose Out section is revised to add a Note
The Compliance in the previous issue(s) of this service bulletin is affected
by this revision. Additional rework to the aircraft is introduced by this
revision.
Remove the previous revision of Service Bulletin 84- - -54- - -14 and replace
with attached.
Previous issue(s) of Service Bulletin 84- - -54- - -14:
Initial issue - - - Pages 1 thru 16 dated 16 Apr 2010
Revision ‘A’ - - - Pages 1 thru 16 dated 22 Apr 2010

### Page 2

Revision ‘B’ - - - Pages 1 thru 16 dated 11 Jun 2010
Revision ‘C’ - - - Pages 1 thru 16 dated 30 Jun 2010
Revision ‘D’ - - - Pages 1 thru 15 dated 05 Jul 2010
Revision ‘E’ - - - Pages 1 thru 22 dated 19 Aug 2010
Revision ‘F’ - - - Pages 1 thru 22 dated 20 Aug 2010
Revision ‘G’ - - - Pages 1 thru 22 dated 09 Sep 2010
Revision ‘H’ - - - Pages 1 thru 22 dated 10 Sep 2010
Revision ‘J’ - - - Pages 1 thru 24 dated 17 Sep 2010

### Page 3

D
S . B . 8 4 --- 5 4 --- 1 4
Page 1 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 5431 NUMBER: 84- - -54- - -14
BOMBARDIER AEROSPACE CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Nacelles - - - Rear Spar Attachment Fitting P/N 85414663- - - *** - - -
Special Inspection and Rectification
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003, 4004, 4006, 4008 thru 4380.
NOTE: For S/N 4003, 4004, 4006, 4008 thru 4380, if the fittings have been
replaced per SB 84- - - 54- - - 15 (refer to previous revisions of this SB)
fittings must be replaced per SB 84- - - 54- - - 16. No further inspections
are required when the SB 84- - - 54- - - 16 is accomplished. Please note
that SB 84- - - 54- - - 15 is now superceded by the SB 84- - - 54- - - 16.
NOTE: SB 84- - - 54- - - 16 is the terminating action to this SB 84- - - 54- - - 14.

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 2 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery on the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s). Before you do
this bulletin, examine all STC or equivalent action changes to make
sure this bulletin can be completed.
Spares Affected:
None
B. Reason
Problem: Operators of the Q400 aircraft have reported finding cracked rear spar
attachment fittings p/n 85414663 (refer to Figure 4 thru 7). Multiple cracks
were found during a normal visual inspection (refer to Figure 1).
Cause: The cause of the problem is related to Stress Corrosion Cracking (SCC).
Solution: This service bulletin gives the instructions to do a detailed visual inspection
and a conductivity test of each attachment fitting p/n 85414663 (qty. 2 per
nacelle, inboard and outboard side). If any attachment fitting is determined
to be cracked or the conductivity of any fitting is outside specified limits,
follow instructions contained within this SB. Replacement instructions are
a v a i l a b l e i n S B 8 4 --- 5 4 --- 1 6 .
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - aircraft electrical power is removed
- - - the nose landing gear lock is engaged
- - - the main landing gear lock pins are installed thru each main gear and main gear door
mechanism
- - - access panels are opened to gain accessto each attachment fitting p/n 85414663 (left
and right side in each nacelle)
- - - each attachment fitting (inboard and outboard) is located and is prepared (cleaned)
for inspection

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 3 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
- - - a detailed visual inspection is accomplished followed by a conductivity test (if
required) with specific attention required at zones identified on Figure 1, Sheet 1 and
Figure 2 in region of Note 1. All results to be recorded and passed to BA for evaluation
- - - if any attachment fitting is found to be cracked or the conductivity is outside specified
limits the fitting must be replaced. Replacement instructions are available in SB
84- - -54- - -16. Contact Bombardier Aerospace for additional instructions
- - - If the fitting is cracked, a ferry flight may be supported, but the conditions must be
reviewed by Bombardier on a case by case basis
- - - close out.
D. Compliance
Bombardier Inc. highly recommends that opera tors inspect their aircraft to determine
the condition of each rear spar attachment fitting p/n 85414663- - -*** (qty. 2
attachment fittings in each nacelle) as follows:
For S/N 4003, 4004, 4006, 4008 thru 4304 a detailed visual inspection and a
conductivity check are required within 100 flight hours upon receipt of this service
bulletin.
For S/N 4305 thru 4313 and 4316 thru 4380 a threshold detailed visual inspection is
required for A/C with a T .A.T . (T otal Airframe Time) of 1200 hours or greater.
For S/N 4003, 4004, 4006, 4008 thru 4380 if the fitting has been replaced thru SB
84- - -54- - -15, then the initial detailed visual inspection is not required for 1200 flight
hours from the time of replacement for that fitting only.
For S/N 4003, 4004, 4006, 4008 thru 4313 and 4316 thru 4380, after the first detailed
visual inspection, a repeat detailed visual inspection is required every 300 flight hours
for each fitting, including all fittings already replaced.
For S/N 4314 and 4315 a repeat detailed visual inspection is required every 300 flight
hours. A threshold detailed visual inspection does not apply to the fittings initially
installed on these aircraft. Threshold inspection is not applicable because
conductivity reading taken by Bombardier show reading between 38.0 % IACS but
less than 40.0 % IACS.
For S/N 4003, 4004, 4006, 4008 thru 4380, if the fittings have been replaced per SB
84- - -54- - -16, no further action is required.

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 4 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
For S/N 4003, 4004, 4006, 4008 thru 4380, if the fittings have been replaced per SB
84- - -54- - -15, fittings must be replaced per 84- - -54- - -16. No further inspections are
r e q u i r e d w h e n t h e S B 8 4 --- 5 4 --- 1 6 i s a c c o m p l i s h e d .
Transport Canada Airworthiness Directive CF- - -2010- - -30R1 has been issued.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
# 9 3 --- Q --- 0 2 .
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F. M a n p o w e r
It will take an estimated 3.0 man- - -hours to inspect / record the condition of all 4
attachment fittings p/n 85414663.
Manpower to replace each attachment fitting assembly p/n 85414663 is specified in
S e r v i c e B u l l e t i n 8 4 --- 5 4 --- 1 6 .
For any on- - -site labor assistance, please speak with a Fleet Services representative
for a quote. The Fleet Services group can be contacted via the Q Series T echnical
Help Desk by telephone at 416- - -375- - -4000 or email at
thd.qseries@aero.bombardier.com
G. Material - - - Price and Availability
None
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 5 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
J. Electrical Load Data
Not affected
K. Publications Affected
None
L. References
Revision ‘K’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
PCR 43228 Revision 1 (for internal reference only)
Transport Canada Airworthiness Directive CF- - -2010- - -30R1
PSM 1- - -84- - -7A Nondestructive T esting Manual
ModSum IS4Q5400012
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Detailed Parts List:
Quantity
Per Aircraft
Part Number Description
4 85414663- - -*** Attachment Assembly (fitting), Rear Spar
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
Refer to Page 9 of this service bulletin, Procedure to Measure the Conductivity of the

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 6 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Nacelle Fittings, Para B., C. and D.
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the quantity
that may be affected per aircraft for non- - -indented parts and the quantity per next
higher assembly for indented parts.
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
85414663- - -*** Attachment
Assembly (fitting),
Rear Spar No. 1
Nacelle
2 C DIS 85414663- - -*** S
85414663- - -*** Attachment
Assembly (fitting),
Rear Spar - - - No.2
Nacelle
2 C DIS 85414663- - -*** S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 7 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate
on part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of Bombardier in the CRC at
1- - -844- - -272- - -2720 (1- - -844- - -CRC- - -CRCO) or email at thd.qseries@aero.bombardier.comfor
analysis and to get an approved disposition to complete this service bulletin.
A . J o b S e t --- U p
WARNING: MAKE SURE THAT ALL HYDRAULIC AND ELECTRICAL POWER IS
OFF . MAKE SURE THAT LOCKPINS ARE INSTALLED IN THE DOOR
MECHANISMS AND THE MAIN LANDING GEAR BEFORE YOU DO
MAINTENANCE IN OR AROUND THE MAIN GEAR WHEEL. THE
DOOR MECHANISMS CAN ACCIDENTL Y CLOSE, THE LANDING
GEAR CAN ACCIDENTL Y RETRACT AND CONTROL SURFACES
COULD MOVE. INJURY TO PERSONNEL AND/OR DAMAGE TO
EQUIPMENT CAN OCCUR.
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K ’ S 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set wheel chocks in front and behind the landing gear tires.

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 8 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
(5) Make sure that the hydraulic system is de- - -pressurized.
(6) Position a ladder or a workstand behind the rear spar adjacent the left and right
side of the No.1 and or No.2 nacelle to permit access to each attachment fitting
p/n 85414663. Make sure the ladder or workstand is electrically grounded.
(7) Remove the access panels that follow (refer to AMM TASK 06- - -41- - -00- - -992- - -806
f o r l o c a t i o n o f p a n e l s a n d A M M T A S K 5 4 --- 2 1 --- 0 6 --- 0 0 0 --- 8 0 1 f o r r e m o v a l
instruction).
ACCESS DESIGNATION
413BL Panel, Access, Rear Spar
413BR Panel, Access, Rear Spar
423BL Panel, Access, Rear Spar
423BR Panel, Access, Rear Spar
B. Procedure
Part A - - - Inspection
(1) Locate each attachment fitting p/n 85414663 in the No.1 and No.2 nacelle. Clean
all debris and unwanted materials from ea ch attachment fitting before conducting
the inspection . Make sure that each fitting is clean and any visible fay sealant is
removed prior to inspection (refer to Figure 2, Sheet 1).
(2) Using adequate lighting and a magnifier lens (and/or optional use of borescope)
do a detailed visual inspection of each atta chment fitting as required (from within
the nacelle and externally thru the area of the removed access panel). Pay
special attention in areas of sloping strut attachment (refer to Figure 1 and area
marked as Figure 2, Sheet 1 in region of Note 1).
If there are any signs of cracking, remove and replace part in accordance with
SB 84- - -54- - -16 before next flight. Refer to Figure 3 thru Figure 7 for typical
crack locations. Inspections are not limited to typical crack locations, the
suspected part should be fully DVI inspected to the extent that is practical
without disassembly.

### Page 11

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 9 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
(3) For Aircraft Serial Numbers 4001 thru 4304, measure and record the conductivity
in accordance with the enclosed Procedure to Measure the Conductivity of the
Nacelle Fittings on each attachment fitting 85414663 as follows: (2 per nacelle, 4
per aircraft) (refer to Figure 2, Sheet 4 & 5). For Aircraft Serial Numbers 4305 thru
4999 electrical conductivity inspection is not required because conductivity
readings have been confirmed by Bombardier, and subsequently, it is not
necessary to repeat conductivity measurements.
PROCEDURE TO MEASURE THE CONDUCTIVITY OF THE NACELLE FITTINGS
A. Purpose
1.Conductivity measurements as required by SB 84- - -54- - -14
B. Equipment
1. Bombardier Aerospace used the following equipment for conductivity
measurements:
a) Instrument Phasec 2200, Eddy current with co nductivity measurement capability,
made by Hocking
b) Eddy current probe 47P001, 60kHz, made by Hocking
c) Cable 33A135, made by Hocking
d) Calibration standards (secondary) made by Fischer T echnology Inc. 45.33% IACS
and 28.71% IACS (”A ” standards)
e) Calibration standard (secondary) made by Fischer T echnology Inc. 39.54%IACS
(”B” standard)
f) DIGI TEMP 16 Level Thermometers, range 10- - -40 degrees C made by LCR
Hallcrest
g) Instrument instruction manual
C. Equivalent Equipment
1. Instruments
a) Conductivity meters or eddy current instruments, probes and cable combinations
with or without temperature sensor that meet the following requirements:
I. Measure conductivity at 60kHz
II. Display the conductivity as a numerical value to at least one decimal place
III. Can be calibrated using at least two conductivity standards (”A ” standards)
IV . Can measure a third standard within the accuracy specified by the conductivity
standard manufacturer (”B” standard)

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 10 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
NOTE: Conductivity meters with a temperature sensor are preferred.
These instruments are available free of charge from Bombardier Aerospace
T oronto, In - - - Service Engineering
2. Calibration standards
a) T wo ”A ” standards (secondary standards only) as follows:
I. One that has the conductivity equal to or less than 30% IACS. Calibration standards
with the conductivity in the range of 25% IACS to 30% IACS are preferred
II. The other standard must have the conductivity equal to or greater than 41% IACS.
Calibration standards with conductivity in the range of 41% IACS to 50% IACS are
preferred.
NOTE: The secondary standards are stand ards that are certified by the standards
manufacturer. The conductivity value of the standards must have a trueness of 0.35%
IACS or 1% of the measured conductivity value, whichever is less at 20 degrees C
b) One ”B” standard made of aluminum (secondary or Bombardier certified
standards) with conductivity between 37% IACS and 40% IACS
NOTE: Bombardier certified standards are certified by comparison to the secondary
standards. These standards are available free of charge from Bombardier Aerospace
T oronto, In - - - Service Engineering
NOTE: All equipment and calibration standards must have a valid certificate of
calibration
D. Preparation
1. Clean all inspection surfaces with approved materials and according to an
approved method until clean paint can be seen. Refer to Structural Repair Manual
(SRM), Ch 51 (PSM 1- - -84- - -3)
2. Inspect the paint. No flakes, bumps or obvious unevenness is allowed at the points
of measurement. Uneven surface, flakes and bumps in the paint may result in
erroneous results. These conditions may be removed by lightly abrading the
inspection surface using Scotch- - -Brite
NOTE: If improvement in the inspection surface cannot be achieved, remove the
paint.
3. If cracks are detected during preparation, remove and replace fitting in accordance
with SB 84- - -54- - -16.

### Page 13

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 11 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
E. Calibration
NOTE: Calibration must be done at the location of the part to be measured.
1. Calibrate the instrument as per the manuf acturer instruction manual using only ”A ”
standards
2. Check the conductivity value of the ”B” standard. The reading must be in the range
specified by the conductivity standards manufacturer. The conductivity value of the
standards must have a trueness of (0.35% IACS) or 1% of the measured value
whichever is less at 20 degrees C
3. Record the conductivity value of the ”B” standard
a) If the instrument, cable and probe combination can not measure standard ”B” with
the specified accuracy, the instrument shall not be used to measure conductivity
4. Verify that the part and the three calibr ation standards used are within 3 degrees C
using the instrument sensor, or the DIGI TEMP 16 Level Thermometer. The accuracy
o ft h et e m p e r a t u r eg a u g eu s e dm u s tb e+ / - - - 1d e g r e eCo rb e t t e r
a) Allow all standards and the part to sit together until they are within 3 degrees C of
each other and then measure the conductivity
b) If the part and calibration standards are within 3 degrees C, recheck the
conductivity value of the ”B” standard.
c) If the conductivity value of the ”B” standard is found within the specified accuracy,
the instrument is calibrated and ready for inspection.
d) If the conductivity value of the ”B” standard is not found within the specified
accuracy, redo the calibration.
e) With the equipment calibrated perform a lift off compensation only if the instrument
used does not have an automatic lift off compensation up to 0.5 mm (0.019 inch).
Refer to the Appendix at the end of this procedure
F . Inspection
NOTE: Perform the inspection immediately after the calibration.
1. Make sure that the instrument is calibrated as in Para E Calibration
2. Make sure that the inspection surface is prepared as in Para D Preparation
3. Measure the conductivity of the points specified in the SB, Figure 2, Sheet 4 & 5.
4. Immediately after taking a measurement, qualify the accuracy of the reading by
re- - -measuring the ”B” standard. The conductivity value of the ”B” standard must be
within +/- - -0.2% IACS of the value obtained during calibration. Record the
conductivity value of the ”B” standard on the reporting sheet
5. If the conductivity value of the ”B” standard is out of range, recalibrate the
instrument per Para. E and re- - -measure the inspection point again.
6. Record the conductivity value of each point measured as required by the SB

### Page 14

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 12 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
G. Reporting: (See Figure 2, Sheet 2 and Figure 2, Sheet 3)
1. Report to Bombardier Aerospace T oronto In Service Engineering the following:
a) Equipment used (Instrument, eddy current probe, cable and calibration standards)
b) Conductivity value and accuracy of each calibration standards used
c) T emperature gauge used (if not included in the instrument)
d) T emperature of the part and standards at the time of inspection
e) Conductivity value for each point measured as per the SB.
f) Conductivity value of the ”B” standard after each point measured.
APPENDIX
LIFT OFF COMPENSATION FOR INSTRUMENTS THAT DO NOT HAVE LIFT OFF
COMPENSATION INCLUDED
A. For coating thickness that is less than 0. 003”, no lift off compensation is required.
For coating thickness that is more than 0.003”, lift off compensation is done by adding
nonconductive material on the ”B” standard until it matches the coating thickness of
the part.
B. If the difference between the two readings (coated and uncoated) on the ”B”
standard is greater than 0.5% IACS, the instrument must not be used
C. If the difference between the two readings is less than or equal to 0.5% IACS, then
the difference value is a correction factor that must be added to the readings taken.
Results of Conductivity Measurements
(a) Record all conductivity readings taken on the fitting at points 1 through 6, 8 and
9 in Figure 2, Sheet 2 and Sheet 3. Identify the minimum conductivity and the
maximum conductivity from the list of all readings for each fitting.
(b) If the fitting is cracked, the fitting must be replaced before further flight. Refer to
SB 84- - -54- - -16. A ferry flight may be supported, but the conditions must be
reviewed on a case by case basis by Bombardier.
(c) If the minimum conductivity is less than 38.0% IACS, or the maximum
conductivity is greater than 45.0% IACS and if the fitting has no cracks, then
conduct daily repeat DVI inspections, and replace fitting within 300 flight hours.

### Page 15

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 13 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
(d) If the minimum conductivity is greater than or equal to 38.0% IACS and the
maximum conductivity is less than or equal to 45.0 % IACS and if the fitting has
no cracks, then conduct repeat DVI inspections every 300 flight hours.
(4) Conductivity readings obtained and inspections completed for aircraft fittings in
accordance with a previous revisions of this Service Bulletin are acceptable
provided conductivity readings have been accomplished in accordance with
MIL- - -STD- - -1537 and fittings and probes used were within 3 degrees Celsius of
each other in accordance with the standard. Aircraft fittings previously inspected
and found to have no cracks may use these readings for assessment in
accordance with criteria noted above in Result of Conductivity Measurements (a)
to (d) and proceed directly to repeat detailed visual inspections where required.
(5) All aircraft subject to 300 flight hour repeat visual inspection, beginning after
initial inspection.
C. Close Out
(1) Apply fay- - -sealant to each fitting and access panel. Refer to SRM 1- - -84- - -3 TASK
5 1 --- 2 3 --- 0 0 --- 0 0 --- 0 1 .
NOTE: Alteratively, it is acceptable to create a fay seal gasket for access
panels in lieu of Fay sealing (refer to ModSum IS4Q5400012).
(2) For any surfaces that were abraded for inspection or otherwise apply alodine,
p r i m e r a n d p a i n t . R e f e r t o S R M 1 --- 8 4 --- 3 T A S K s 5 1 --- 2 1 --- 1 0 --- 0 2 --- 0 1 ,
5 1 --- 2 5 --- 1 0 --- 0 2 --- 0 1 a n d 5 1 --- 2 5 --- 1 5 --- 0 2 --- 0 1 .
(3) Close the access panels that follow (refer to AMM TASK 06- - -41- - -00- - -992- - -806
for location of panels and TASK 54- - -21- - -06- - -400- - -801 for removal instruction).
ACCESS DESIGNATION
413BL Panel, Access, Rear Spar
413BR Panel, Access, Rear Spar
423BL Panel, Access, Rear Spar
423BR Panel, Access, Rear Spar
(4) Remove all tools and equipment from the work area.

### Page 16

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 14 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
(5) Submit all reported findings to: the ‘‘T oronto Help Desk at telephone number
(416) 375- - -4000 or facsimile (416) 375- - -4539’’ or E- - -mail:
thd.qseries@aero.bombardier.com for a corrective action. Return all removed
parts to Bombardier Aerospace.
Ship removed parts to :
Bombardier Commercial Aircraft
Attention: Anthony Assivero
Line Manager in Receiving/Shipping Inspection
123 Garratt BlvdT oronto, ON, M3K 1Y5
Canada
Note:
All parts need to be red tagged.
Removal tags need to be filled out with the following information:
1. Date of removal
2. Customer Name
3. A/C removed off
4. Part number
5. Serial number
6. Reason for removal
7. Flight hours and cycle, or time since new
(6) On completion of this service bulletin, make the following entry in the appropriate
logbooks: “Service Bulletin 84- - -54- - -14, Rear Spar Attachment Fitting Part
Number 85414663 - - - Special Inspection and Rectification accomplished. If only
part of this Service Bulletin is completed, detail the exact limit of work completed.
Enter component serial numbers if applicable in affected logbooks.

### Page 17

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 15 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Nacelle Attachment Assemblies - - - Locator View
Figure 1
NACELLE ATTACHMENT ASSEMBL Y
X
X
X
INSPECT INSIDE AND OUTSIDE OF FITTING
SLOPING STRUT ATTACHMENT AREAS,
ON BOTH FITTINGS OF EACH NACELLE

### Page 18 (OCR)

SERVICE BULLETIN 84-54-14
Nacelle Attachment Fitting Assy.  P/N 85414663  View Looking Inbd on RH Nacelle  Inbd Nacelle Attachment Fitting.  Note: Refer to Figure 2 Sheet 4 & 5 for locations  In the indicated area make sure that all sealant  is removed from the fitting and that the area is  clean before testing.
VIEW ON BACK FACE  Remove access panels  413BL, 413BR, 423BL, 423BR
Locations to record conductivity readings are num-  bered 1 thru 6, 8 and 9. All conductivity readings are to  be measured in accordance with enclosed Procedure  to Measure the Conductivity of the Nacelle Fittings.  Record conductivity values Refer to Figure 2 Shts 2 & 3  Measurement on  aft side of aft lug
Conductivity Locations
Figure 2 Sheet 1
16 Apr 2010  S.B. 84-54-14
Revision 'K' 07 Aug 2018  Page 16 of 26
MG/PM

### Page 19

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 17 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Conductivity Locations - - - No.1 Nacelle
Figure 2 Sheet 2
No. 1 Nacelle Outboard Fitting Assy No.1 Nacelle Inboard Fitting Assy
DATE:A/C S/N:
A/C HOURS:
A/C CYCLES:
TEMP OF PART
INSPECTION
TEMP OF PART
INSPECTION
EQUIPMENT USED TO
MEASURE CONDUCTIVITY :
CONDUCTIVITY VALUE/
A - - - STD ACCURACY :
TEMPERATURE GAUGE
USED:
CONDUCTIVITY READING IACS CONDUCTIVITY READING IACS
FITTINGREADING READINGB --- S T D READINGFITTING B --- S T DREADINGLOCATION LOCATION

### Page 20

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 18 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Conductivity Locations - - - No.2 Nacelle
Figure 2 Sheet 3
No. 2 Nacelle Outboard Fitting Assy No.2 Nacelle Inboard Fitting Assy
DATE:A/C S/N:
A/C HOURS:
A/C CYCLES:
TEMP OF PART
INSPECTION
TEMP OF PART
INSPECTION
EQUIPMENT USED TO
MEASURE CONDUCTIVITY :
CONDUCTIVITY VALUE/
A - - - STD ACCURACY :
TEMPERATURE GAUGE
USED:
CONDUCTIVITY READING IACS CONDUCTIVITY READING IACS
FITTINGREADING READINGB --- S T D READINGFITTING B --- S T DREADINGLOCATION LOCATION

### Page 21 (OCR)

SERVICE BULLETIN 84-54-14
FWD
Conductivity Locations  Figure 2 Sheet 4
16 Apr 2010  S.B. 84-54-14
Revision 'K' 07 Aug 2018  Page 19 of 26
MG/PM

### Page 22 (OCR)

SERVICE BULLETIN 84-54-14
FWD
Conductivity Locations  Figure 2 Sheet 5
16 Apr 2010  S.B. 84-54-14
Revision 'K' 07 Aug 2018  Page 20 of 26
MG/PM

### Page 23

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 21 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Fwd Sloping Strut, T ypical Crack Lo cation on Nacelle Attachment Fitting
Figure 3

### Page 24

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 22 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Fwd Sloping Strut, T ypical Crack Lo cation on Nacelle Attachment Fitting
Figure 4
Crack
Crack
Crack

### Page 25

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 23 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Nacelle Attachment Fitting, Inboard Side Crack Location
Figure 5
CRACK

### Page 26

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 24 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
Rear Spar Attachment Fitting - - - Depicting a Crack
Figure 6
CRACK

### Page 27

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 25 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
T ypical Crack Locations on P/N 85414564- - - 109/110
Figure 7
CRACKS
P/N 85414564- - -110
1
UP
FWD
V
V
1

### Page 28

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 1 4
S . B . 8 4 --- 5 4 --- 1 4
Page 26 of 26
16 Apr 2010
Revision ‘K’ 07 Aug 2018 MG/PM
This Page Intentionally Blank.

### Page 29

May2018
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 30

May 2018
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
