# Bombardier Service Bulletin 84-54-20

Copy: Revision C ("FAA-2015-3986 SB 84-54-20C"), 30 pages: PDF https://openairdocs.org/files/sha256/c6/81/c6816871876fc1191fa36ffa406fd01bfb775739b4a0587ab652c6efa2489b73; text https://openairdocs.org/service-documents/bombardier/sb-84-54-20/file/c6816871876f.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-3986; AD 2016-16-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-54-20
- Latest revision known: 84-54-20, Revision C, dated March 5, 2015 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-54-20

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-16-15](https://openairdocs.org/ad/2016-16-15.md), effective Sep 23, 2016: Revisions A, B and C

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-54-20/proposed.md).

## Text (30 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-3986; AD 2016-16-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Revision ‘C’ 05 Mar 2015
D H C --- 8 ( D A S H 8 )
S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
Nacelles - - - A- - - Frame - - - Retrofit - - - Flanges Trimmed for Clearance to
Retracted MLG Stabilizer Brace - - - ModSum 4- - - 113776
This page transmits Revision ‘C’ of Service Bulletin 84- - -54- - -20, pages 1 thru
26, dated 05 Mar 2015.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- t h eCompliance section is revised to add the reference to AD CF- - -2014- - -45
Part II
--- t h eReferences section is revised to convey the latest revision of the service
bulletin and engineering documentation
--- t h eACCOMPLISHMENT INSTRUCTIONS section is revised to move the
J o b S e t --- U pinstructions that are applicable only to the rework to
Procedure section P a r t --- B --- R e w o r k
--- t h eProcedures section is revised to change the AMM TASK reference in
step (j) from 32- - -31- - -00- - -710- - -301 to 32- - -31- - -00- - -710- - -801.
The Compliance in the previous issue(s) of this service bulletin is not
affected by this revision. No additional rework to the aircraft is introduced by
this revision.
Remove the previous revision of Service Bulletin 84- - -54- - -20 and replace
with attached.
Previous issue(s) of Service Bulletin 84- - -54- - -20:
Initial issue - - - Pages 1 thru 24 dated 25 Apr 2013
Revision ‘A’ - - - Pages 1 thru 24 dated 09 Apr 2014
Revision ‘B’ - - - Pages 1 thru 26 dated 02 Oct 2014

### Page 2

(No text on this page.)

### Page 3

D
S . B . 8 4 --- 5 4 --- 2 0
Page 1 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 5420 NUMBER: 84- - -54- - -20
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
URGE OPERATORS TO PROMPTL Y EVALUATE THE CONTENTS
SUBJECT : Nacelles - - - A- - - Frame - - - Retrofit - - - Flanges Trimmed for Clearance to
Retracted MLG Stabilizer Brace - - - ModSum 4- - - 113776
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC- - -8 Aircraft Models 401 and 402 Serial Numbers 4056
thru 4426.
NOTE: If ModSum IS4Q5450003 was previously accomplished, no further
action is required.
NOTE: It is highly recommended that this Service Bulletin be accomplished
concurrently with service bulletin 84- - -32- - -114.
Production: ModSum 4- - -123818 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Numbers 4427 thru 4454,
4456, 4457, 4459, 4460 and 4463.
ModSum 4- - -170073 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4455.
ModSum 4- - -170060 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Numbers 4458, 4461,
4462, 4464 and subsequent.

### Page 4

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 2 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
NOTE: The instructions in this service bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
Spares Affected:
None
B. Reason
Problem: There is insufficient clearan ce between the main landing gear (MLG)
stabilizer brace and nacelle A- - -Frame. Impact between the MLG stabilizer
brace and nacelle A- - -Frame may lead to reduced structural integrity of the
nacelle A- - -Frame and MLG stabilizer brace.
Solution: This service bulletin introduces ModSum 4- - -113776.
The ModSum reworks the nacelle A- - -Frame flanges to improve the
clearance between the MLG stabilizer brace and the nacelle A- - -Frame.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
follow:
- - - nose landing gear lock is engaged
- - - main landing gear lock pins are installed thru each main gear and main gear
door mechanism
- - - aircraft is lifted on jacks
- - - main landing gear forward doors are removed
- - - pressure in the No. 1, 2 & 3 hydraulic systems is depleted
- - - all aircraft electrical power systems are selected to OFF
- - - work platforms or ladders are set up and properly grounded
- - - main landing gear stabilizer struts, and harnesses if necessary, are removed

### Page 5

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 3 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
- - - LH and RH nacelle A- - -Frame flanges are reworked and inspected
- - - reworked areas are flap peened and re- - -finished with alodine, F19 epoxy primer
and F24 polyurethane enamel
- - - fluorescent penetrant inspection or high frequency eddy current inspection of
the reworked and adjacent areas is done
- - - flap peen of the reworked area is done
- - - expose surfaces are cleaned and treated
- - - removed harnesses and tie mounts are re- - -installed
- - - clearance between nacelle A- - -Frame and MLG stabilizer brace in the reworked
a r e a si sm e a s u r e d
- - - Bombardier T echnical Help Desk is contacted if clearance is not within limits
- - - LH and RH A- - -Frame assemblies are re- - -identified and coated if clearance is
within limits
- - - landing gear is extended
- - - main landing gears forward doors are re- - -installed
- - - aircraft is lowered and jacks are removed
- - - close out.
D. Compliance
Bombardier Inc. highly recommends that ModSum 4- - -113776 be incorporated at
the earliest opportunity unless otherwise directed by the operator’s airworthiness
authority.
Transport Canada Airworthiness Directive CF- - -2014- - -45 Part II.
E. Approval
The technical content of this service bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
O r g a n i z a t i o n N o : D A O # 9 3 --- Q --- 0 2 .

### Page 6

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 4 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
F. M a n p o w e r
It will take an estimated 21 man- - -hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.50
Procedure 20.00
T e s t/R T S 0.00
Close- - -Out 0.50
For any on- - -site labor assistance, please speak with a Fleet Services representative for
a quote. The Fleet Services group can be contacted via the Q Series T echnical Help
Desk by telephone at 416- - -375- - -4000 or email at: thd.qseries@aero.bombardier.com.
G. Material - - - Price and Availability
T h eM o d K i tr e q u i r e dt od ot h i ss e r v i c eb u l l e t i ni sl i s t e di nt h et a b l eb e l o w .
Operators should submit a purchase orde r through the Customer Accounts Service
T eam (CAST) at Bombardier Aerospace Regional Aircraft division specifying aircraft
serial number(s) to:
Bombardier Aerospace
Customer Accounts Services T eam (Mail Stop N11- - -32)
123 Garratt Blvd.
To r o n t o
Ontario
Canada M3K- - -1Y5
Facsimile: (416) 375- - -3060
T elephone: (416) 375- - -3920

### Page 7

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 5 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
Facsimile:
International: (416) 375- - -3334
European: (416) 373- - -5966
Americas East: (416) 373- - -5964
Americas West: (416) 373- - -5965
T elephone:
International: (416) 375- - -3706
European: (416) 373- - -3704
Americas East: (416) 375- - -3700
Americas West: (416) 373- - -5888
E- - -mail addresses:
International: cast.international@aero.bombardier.com
European: cast.europe@aero.bombardier.com
Americas East: cast.americaseast@aero.bombardier.com
Americas West: cast.americaswest@aero.bombardier.com
Kit Number Description
8DK4205- - -001 D r a w i n g K i t --- N a c e l l e , A --- F r a m e
The part(s) and material(s) detailed in Paragraph 2.A. may be either furnished or
fabricated from the operator’s existing stock, purchased as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources. DK parts are to be manufactured and approved locally (refer to disclaimer
in the related text or illustration). In some cases, an equivalent to the DK part may
be available from Bombardier under the production part number shown as
reference in Parts Required Per Aircraft.
H. T ooling - - - Price and Availability
Part Number Description Remarks
85414787- - -115- - -76 Marking T ool

### Page 8

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 6 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Dash 8 Illustrated Parts Catalogue PSM 1- - -84- - -4....................
ModSums Manual PSM 1- - -84- - -12..................................
L. References
Revision ‘C’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8DK4205 1 --- ---
8Z9566 1 A
ModSum 4Q113776 Rev. ‘D’
ModSum 4- - -113776 Rev. ‘D’
ModSum 4Y123798 Rev. ‘B’
ModSum 4- - -123798 Rev. ‘B’
ModSum 4Y123818 Rev. ‘H’
ModSum 4- - -123818 Rev. ‘H’
ModSum 4Q126562 Rev. ‘F’
ModSum 4- - -126562 Rev. ‘F’

### Page 9

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 7 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
ModSum 4D170073 Rev. ‘A’
ModSum 4- - -170073 Rev. ‘A’
ModSum 4D170060 Rev. ‘D’
ModSum 4- - -170060 Rev. ‘D’
ModSum IS4Q5450003 Rev. ‘C’
S e r v i c e B u l l e t i n 8 4 --- 3 2 --- 1 1 4
ModSum IS4Q2400028 Rev. ‘B’
ModSum IS4Q2400029 Rev. ‘A’
All Operator Message (AOM) 389
PCA 44059 Revision 3 (for internal reference only)
Transport Canada Airworthiness Directive CF- - -2014- - -45
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Drawing Kit 8DK4205- - -001
(2) Detailed Kit Content:
Quantity Per Kit
--- 0 0 1
Part Number Description Remarks
--- 8Z9566 Retrofit Drawing Drawing Only
--- 8DK4205 Kit Drawing Only

### Page 10

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 8 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
NOTE: This service bulletin is self- - -contained (illustrated). No drawings will be
supplied.
NOTE: Operators who would like the drawings to be supplied to them should
follow the instructions given in AOM 389.
(3) In addition to the above part(s), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in
either Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter
51 or, for 400 Series Aircraft, in Consumable Products Manual PSM
1 --- 8 4 --- 1 8 .
Part No/
Product ID No.
Qty. Per Aircraft Description Remarks
05- - -11
or 05- - -23
or 05- - -34
As Required Adhesive, Epoxy
Adhesive, Acrylic
DHMS CA6.09
Fastweld #10
CB200 or
CB200- - -40
07- - -02 1/4 Pint Primer, Chromated
Epoxy
DHMS C4.01 or
MIL- - -PRF- - -23377
07- - -08 1/4 Pint Coating, Polyure-
thane Enamel (F24)
MIL- - -PRF- - -85285
DHMS C4.04 T ype 4
07- - -21 1/2 Ounce Coating, Chemical
Conversion
MIL- - -C- - -5541
13- - -65 As Required Fluorescent Pene-
trant
ASTM- - -E- - -1417
NOTE: Refer to CPM PSM 1- - -84- - -18 for the list of approved alternative
consumable products under each Product ID No., any of which can be
used unless a note states otherwise.

### Page 11

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 9 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
Reference Description Remarks
--- Eddy Current instrument Phasec
2200 (Hocking) or equivalent
Commercially available
--- Calibration T est Standard, Hocking,
P/N (CTS) SRS 0824A or equivalent
Commercially available
NOTE: The above tools/equipment are only necessary if a high frequency eddy
current (HFEC) inspection is done.
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non- - -indented parts and the quantity
p e rn e x th i g h e ra s s e m b l yf o ri n d e n t e dp a r t s .
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
85414787- - -107 or
85414787- - -109 or
85414787- - -111 or
85414787- - -113 or
85414787- - -115
A --- F r a m e ( L H ) 1 A RWK 8Z9566- - -001 R
85414787- - -108 or
85414787- - -110 or
85414787- - -112 or
85414787- - -114 or
85414787- - -116
A --- F r a m e ( R H )
1
A RWK 8Z9566- - -002 R

### Page 12

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 10 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Inst allation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate
on part that this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.
3. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
NOTE: If ModSum IS4Q5450003 is previously accomplished, no further rework is
necessary.
(1) Make sure the nose gear ground lock is engaged.
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.

### Page 13

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 11 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
B. Procedure
P a r t A ---Inspection
(1) Inspect the LH and RH A- - -frames and the upper surface stabilizer brace lug as
follows:
(a) Do a detailed visual inspection of the A- - -frame (refer to Figure 2, Sheet 1)
and of the upper surface of stabilizer brace lug (refer to Figure 3, Sheet 2
and Figure 4).
(b) If damage is found, contact the Q Series T echnical Help Desk by telephone at
416- - -375- - -4000 or email at: thd.qseries@aero.bombardier.com for approved
repair.
P a r t B ---Rework
(1) Jack the aircraft (refer to AMM TASK 07- - -10- - -00- - -582- - -801).
(2) Remove the LH and RH MLG forward doors (refer to AMM TASK
32- - -12- - -11- - -000- - -801).
(3) Deplete hydraulic pressure in the No. 1, 2 & 3 systems (refer to AMM TASKs
29- - -00- - -00- - -863- - -802 and 29- - -00- - -00- - -863- - -804).
(4) Install a warning sign on the external hydraulic connection.
(5) Placard and select all aircraft electrical power to OFF . Obey all relevant
W A R N I N G S a n d C A U T I O N S ( r e f e r t o A M M T A S K s 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2 a n d
24- - -00- - -00- - -910- - -801).
(6) Set up work platforms or ladders as required to gain access to the stabilizer
brace in the No. 1 and/or No. 2 wheel well (refer to Figure 1). Make sure that the
work platforms or ladders are electrically grounded.
(7) Remove the LH and RH MLG Stabilizer struts (refer to AMM TASK
32- - -11- - -16- - -000- - -801).

### Page 14

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 12 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
(8) If necessary, remove the MLG harnesses to gain access to the rework area (refer
to Figure 5). If a harness tie mount is installed on the rework area, mark/record
the position and remove it before doing PART B- - -Rework of this service bulletin
(refer to Figure 5).
(9) Rework the LH and RH A- - -Frame flanges as follows (refer to Figure 2):
(a) Mark intersection point of flanges as shown in Figure 2 Sheet 2 DETAILS E and
F . Mark flange trim locations as shown in Figure 2 Sheet 1 DETAIL A from this
point.
NOTE: For ease of marking, the use of marker tool P/N
85414787- - -115- - -76 is acceptable.
(b) Remove material from A- - -Frame (refer to Figure 2 Sheet 3 SECTION B- - -B,
Sheet 4 DETAILS G and H, Sheet 5 SECTION C- - -C, Sheet 6 Section D- - -D and
Figure 5).
(c) Finish edges (refer to applicable instructions in SRM 51- - -14- - -00) and deburr
and clean cut metal edges (refer to applicable instructions in SRM
51- - -26- - -00).
(d) Inspect reworked area and adjacent area for cracks using FPI (preferred
method) per ASTM- - -E- - -1417 using T ype 1 Method C Level 3 Form d or using
HFEC inspection (alternate method) per PSM 1- - -84- - -7A NDT Manual Part 6
51- - -00- - -01. If crack is found, contact the Q Series T echnical Help Desk by
telephone at 416- - -375- - -4000 or email at: thd.qseries@aero.bombardier.com for
approved disposition/action.
(e) If fluorescent penetrant inspection (FPI) of the reworked area and adjacent
area will be done, perform etching of the area to be inspected per SRM
51- - -20- - -00.
(f) Flap peen reworked areas per MIL- - -R- - -81841 or equivalent. Make sure the
intensity is 0.006A to 0.008A.

### Page 15

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 13 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
(g) Clean and treat exposed surfaces with Alodine (Product ID No. 07- - -21) and
then apply epoxy primer (Product ID No. 07- - -02) and polyurethane enamel
(Product Id No. 07- - -08) on all applicable rework areas (refer to CPM PSM
1- - -84- - -18 for approved alternatives and to applicable instructions in AMM
TASKs 51- - -25- - -16- - -390- - -801, 51- - -25- - -26- - -370- - -801 and
51- - -25- - -31- - -370- - -801).
(h) Re- - -install harnesses and the harness tie mount that was removed to the
recorded location. Attached tie mount with adhesive 05- - -11 or 05- - -23 or
05- - -34 (refer to AMM TASK 20- - -10- - -08- - -400- - -802 and Figure 5)
NOTE: Harnesses can be rerouted per SB 84- - -32- - -114 or ModSum
IS4Q2400028 (A/C 4056- - -4089) or ModSum IS4Q2400029 (A/C
4090- - -4411).
(i) Remove all tools, equipment and unwanted materials from the nacelle work
area.
(j) Measure the clearance between the nacelle A- - -Frame and MLG stabilizer
brace assembly in the reworked area as follows (refer to Figure 3 and Figure
4):
1 Re- - -install the LH and RH MLG stabilizer struts (refer to AMM TASK
32- - -11- - -16- - -400- - -801).
2 With the LH and RH forward doors still removed from aircraft, do the
Operational T est of the Landing Gear Primary Extension and Retraction
System (refer to AMM TASK 32- - -31- - -00- - -710- - -801). Swing the landing
gear up and leave in the up and locked position.
3 With the MLG in retracted position, measure the clearance between the
A- - -frame and MLG stabilizer brace assembly in the reworked areas
(refer to Figure 3 per flagnote 1 in VIEW A and SECTIONs C- - -C and
D --- D .

### Page 16

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 14 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
NOTE: If the clearance limit to the harness cannot be met, re- - -dress the
harness routing per SB 84- - -32- - -114 (or ModSum IS4Q2400028 on
aircraft s/n’s 4056 thru 4089 or ModSum IS4Q2400029 on aircraft
4090 thru 4411) and ModSum 4Y123798 on aircraft s/n’s 4412 thru
4426.
(k) If the minimum clearance is less than 0.100 in. (2.54 mm), contact the Q Series
T echnical Help Desk by telephone at 416- - -375- - -4000 or email at:
thd.qseries@aero.bombardier.com for approved disposition/action.
(l) If the clearance is equal or more than 0.100 in. (2.54 mm), re- - -identify the LH
A- - -Frame as 8Z9566- - -001 and RH A- - -Frame as 8Z9566- - -002 with indelible
marking. After the identification mark ings have dried, apply a clear coat (no
color) of polyurethane enamel (Product ID No. 07- - -08) (refer to CPM PSM
1- - -84- - -18 and to applicable instructions in AMM TASK
51- - -25- - -31- - -370- - -801).
(m) Extend the landing gear (refer to applicable instructions in AMM T ask
32- - -31- - -00- - -867- - -801).
(n) Re- - -install the MLG forward doors (refer to AMM TASK
32- - -12- - -11- - -400- - -801) and rig the doors (refer to AMM TASK
32- - -12- - -11- - -830- - -801).
(o) Lower the aircraft on jacks and remove the jacks (refer to applicable
instructions in AMM T ask 07- - -10- - -00- - -582- - -801).
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.
THE DESIGN OF THE PART IN THIS DRAWING HAS BEEN APPROVED BY DE HAVILLAND INC. FOR MANUFACTURE BY OR ON BEHALF OF
THE RECIPIENT . THE RECIPIENT IS RESPONSIBLE FOR (A) PROP ER MANUFACTURE OF THE PART USING THE SPECIFIED MATERIALS
AND FOR INCORPORATION OF THE MODIFICATION, ALL IN ACCORD ANCE WITH THE DRAWING AND RELATED INSTRUCTIONS, AND (B)
APPROVAL OF THE FINAL INSTALLATION BY THE RELEVANT AIRWORT HINESS AUTHORITY . DE HAVILLAND INC. AND BOMBARDIER INC.
(BOMBARDIER AEROSPACE REGIONAL AIRCRAFT) DISCLAIM ANY RE SPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION LOSS OF USE, LOSS OF REVENUE OR LOSS OF PROFIT , ARISING FROM SUCH MANUFACTURE,
INCORPORATION AND INSTALLATION.

### Page 17

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 15 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 1
AREA OF RETROFIT

### Page 18

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 16 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 1)
NOTE: All dimesions are in inches.
DETAILED VISUAL INSPECTION FOR DAMAGE

### Page 19

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 17 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 2)
NOTE: All dimesions are in inches.

### Page 20

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 18 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 3)
NOTE: All dimesions are in inches.
G
H

### Page 21

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 19 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 4)
NOTE: All dimesions are in inches.
DETAIL G
DETAIL H

### Page 22

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 20 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 5)
NOTE: All dimesions are in inches.

### Page 23

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 21 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
R e t r o f i t --- N a c e l l e A --- F r a m e
Figure 2 (Sheet 6)
NOTE: All dimesions are in inches.

### Page 24

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 22 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
STABILIZER BRACE
A --- F R A M E
Nacelle A- - - Frame and MLG Stabilizer Brace - - - Clearance Measurement
Figure 3 (Sheet 1)
WITH THE MAIN LANDING GEAR RETRACTED, MEASURE THE CLEARANCE
BETWEEN THE NACELLE A- - -FRAME AND MLG STABILIZER BRACE.

### Page 25

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 23 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
STABILIZER BRACE
P/N 46400- - -25 SHOWN
WITH THE MAIN LANDING GEAR RETRACTED, MEASURE THE CLEARANCE
BETWEEN THE NACELLE A- - -FRAME AND MLG STABILIZER BRACE.
Nacelle A- - - Frame and MLG Stabilizer Brace - - - Clearance Measurement
Figure 3 (Sheet 2)
STABILIZER BRACE
P/N 46400- - -27 SHOWN
0.100 IN. (2.54 MM) MIN
0.100 IN. (2.54 MM) MIN
(MINIMAL DISTANCE BETWEEN
STOP BRACKET AND A- - -FRAME)
(MINIMAL DISTANCE BETWEEN STABILIZER
BRACE STRUCTURE AND A- - -FRAME)
DETAILED VISUAL
INSPECTION FOR DAMAGE
DETAILED VISUAL
INSPECTION FOR DAMAGE
SECTION
C --- C
SECTION
D --- D
SECTION
C --- C
SECTION
D --- D

### Page 26

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 24 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
Nacelle A- - - Frame and MLG Stabilizer Brace - - - Clearance Measurement
Figure 4
INSPECTION AREA
( A --- F R A M E A N D M L G
STABILIZER BRACE) CLEARANCE BETWEEN MLG
BRACE ASSEMBL Y AND A- - -FRAME
MINIMUM 0.100 IN. (2.54 MM)
DARK AREA SHOWING
MATERIAL TO BE REMOVED
NOTE: If clearance limit to the harnesses cannot be met. redress the harness routing
per SB 84- - -32- - -114 or ModSum IS4Q2400028 (a/c 4056 thru 4089) or ModSum
IS4Q2400029 (a/c 4090 thru 4411).

### Page 27

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 25 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
Trimmed Nacelle A - - - Frame
Figure 5
2 34
IF NECESSARY , REMOVE WIRING HARNESS TO GAIN ACCESS TO THE REWORK AREA.2
IF A HARNESS TIE MOUNT IS INSTALLED ON THE REWORK AREA, MARK/RECORD THE3 POSITION AND REMOVE IT BEFORE REWORK.
AFTER REWORK, RE- - -INSTALL HARNESS TIE MOUNT TO THE RECORDED LOCATION.4 ATTACHED TIE MOUNT WITH ADHESIVE 05- - -11, OR 05- - -23 OR 05- - -34 (REFER TO AMM
TASK 20- - -10- - -08- - -400- - -802). HARNESSES CAN BE REROUTED PER SB 84- - -32- - -114 OR
IS4Q2400028 (A/C 4056- - -4089) OR IS4Q2400029 (A/C 4090- - -4411).

### Page 28

S E R V I C E B U L L E T I N 8 4 --- 5 4 --- 2 0
S . B . 8 4 --- 5 4 --- 2 0
Page 26 of 26
25 Apr 2013
Revision ‘C’ 05 Mar 2015 NB
This Page Intentionally Blank
1

### Page 29

Jan 2009
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
- - - Q SERIES DASH 8 AIRCRAFT
To : CMDB Focal
Facsimile: (1) 416 375 4538
E- -mai l: cmdb.requests@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

### Page 30

Feb 2009
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - Q SERIES DASH 8 AIRCRAFT
To : SB Focal (T oronto), Bombardier Aerospace Commercial Aircraft
Phone: (1) 416 375 4078 Facsimile: (1) 416 375 4538
E- -mai l: syed.rizvi@aero.bombardier .com
From:
Company:
Phone: Extn:
Facsimile: Date:
E- -mai l:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Fax this sheet to (1) 416 375 4538 or Email PDF to:
syed.rizvi@aero.bombardier.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
