# De Havilland Canada Service Bulletin 84-54-31

Copy: Revision C ("84-54-31 Rev C"), 38 pages: PDF https://openairdocs.org/files/sha256/00/ab/00ab026c2285aa07facbd1adb85be37387dfb2d7fb3ed01ecf685bacca869c41; text https://openairdocs.org/service-documents/bombardier/sb-84-54-31/file/00ab026c2285.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0514; AD 2022-01-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md) (issued as De Havilland Canada)
- Type: Service bulletin (Service Bulletin)
- Number: 84-54-31
- Latest revision known: 84-54-31, Revision C, dated March 15, 2021 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-54-31

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2022-01-02](https://openairdocs.org/ad/2022-01-02.md), effective Mar 3, 2022: Revisions A, B and C

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-54-31/proposed.md).

## Text (38 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0514; AD 2022-01-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

T x L t r S B 8 4 --- 5 4 --- 3 1
P a g e1o f2
Revision ‘C’ 15 Mar 2021
JV
DHC - - -8 (DASH 8)
SERVICE BULLETIN 84 - - -54 - - -31
Nacelle - - - MLG Pins Corrosion Issues - - - Apply Missing F19 Primer and F13
Corrosion Preventive Compound - - - ModSum 4 - - -113997
This page transmits Revision ‘C’ of Service Bulletin 84- - - 54- - - 31, pages 1 thru 34,
dated 15 Mar 2021.
This service bulletin is re- - -issued in its entirety for the reasons that follow:
--- T h eEffectivity section is revised to reflect the latest Production from 4600 and
subsequent to 4600 thru 4633 and added Production Modsum 4- - - 170096
--- T h eReferences section is revised to convey the latest revision of the service
bulletin
--- T h eParts Required Per Aircraft section is revised to add Consumable Product ID
number 07- - - 53 (Type 6 Class B Polyurethane Enamel) as an alternate to
Consumable Product ID number 07- - - 08 and revised theDetailed Kit Content
table.
--- T h eProcedure section is revised to add a note that production pins can replace
pins that are found to be corroded.
The Compliance in the previous issue(s) of this service bulletin is not affected by
this revision. No additional rework to the aircraft is introduced by this revision.
Remove the previous revision of Service Bulletin 84- - - 54- - -31 and replace with
attached.
Previous issue(s) of Service Bulletin 84- - - 54- - - 31:
Initial issue - - - Pages 1 thru 32 dated - - - 01 May 2019
Revision ’A’ - - - Pages 1 thru 32 dated - - - 15 Oct 2019
Revision ’B’ - - - Pages 1 thru 32 dated - - - 21 Feb 2020

### Page 2

SERVICE BULLETIN 84- - -54- - -31
T x L t r S B 8 4 --- 5 4 --- 3 1
P a g e2o f2
Revision ‘C’ 15 Mar 2021
JV
This Page Intentionally Blank
1

### Page 3

S . B . 8 4 --- 5 4 --- 3 1
Page 1 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
SERVICE BULLETIN
Customer
Support
ATA SYSTEM: 5400 N U M B E R : 8 4 --- 5 4 --- 3 1
DE HAVILLAND AIRCRAFT OF CANADA LIMITED (DHC) CONSIDERS
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
THIS SERVICE BULLETIN TO BE PARTICULARL Y SIGNIFICANT AND
SUBJECT : Nacelle - - - MLG Pins Corrosion Issues - - - Apply Missing F19 Primer and
F13 Corrosion Preventive Compound - - - ModSum 4 - - -113997
1. PLANNING INFORMA TION
NOTE: This service bulletin supercedes service bulletin 84- - -54- - -27
A. Effectivity
Aircraft Affected:
NOTE: Operators that have done SB 84- - -54- - -27 are required to do this service
bulletin.
In- - -Service: DHC - - - 8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4533 with the following nacelle pins:
85414799- - - 107 or 8Z10128- - - 101, 8Z10128- - - 105
85414799- - - 109 or 8Z10128- - - 103, 8Z10128- - - 107
85414800- - - 107 or 8Z10125- - - 101, 8Z10125- - - 105
85414800- - - 109 or 8Z10125- - - 103, 8Z10125- - - 107
85414794- - - 105 or 8Z10126- - - 101, 8Z10126- - - 105
85414794- - - 107 or 8Z10126- - - 103, 8Z10126- - - 107
85414567- - - 107 or 8Z10127- - - 101, 8Z10127- - - 105
85414567- - - 109 or 8Z10127- - - 103, 8Z10127- - - 107

### Page 4

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 2 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
In- - -Service: DHC - - - 8 Aircraft Model 402 Serial Numbers 4583, 4584, 4585,
4587, 4588 and 4590.
NOTE: The following aircraft have had pin 85414567- - - 109 reworked per the
following NCR’s and have to re- - -part mark the pin per the instructions
on this service bulletin.:
- - - 4583 reworked per NCR D118010674
- - - 4584 reworked per NCR D118010304
- - - 4585 reworked per NCR D118010288
- - - 4587 reworked per NCR D118010301 (LH) & D118010320 (RH)
- - - 4588 reworked per NCR D118009038
- - - 4590 reworked per NCR D118009771
NOTE: The original pins of Aircraft 4534- - - 4582, 4586, 4589 and 4591- - - 4599
have been confirmed to have a single coat of primer applied in
accordance with the drawing intent in the pre- - - Modsum 4- - - 113997
condition and do not require rework.
Production: ModSum 4- - - 113997 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4600 to 4633.
Production: ModSum 4- - - 170096 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4634 and
subsequent.
Spares Affected:
The following is a list of spares affected by this change. Review spares and
procurement systems to determine the existence of any listed parts.
Part Number Description
85414567- - - 107 Y oke Attachment Pin
85414567- - - 109 Y oke Attachment Pin
85414799- - - 107 Sidebrace Pin
85414799- - - 109 Sidebrace Pin
85414800- - - 107 Sidebrace Pin
85414800- - - 109 Sidebrace Pin
85414794- - - 105 Drag Strut Attachment Pin

### Page 5

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 3 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Part Number Description
85414794- - - 107 Drag Strut Attachment Pin
8Z10125- - - 101 Sidebrace Pin
8Z10125- - - 103 Sidebrace Pin
8Z10125- - - 105 Sidebrace Pin
8Z10125- - - 107 Sidebrace Pin
8Z10126- - - 101 Drag Strut Attachment Pin
8Z10126- - - 103 Drag Strut Attachment Pin
8Z10126- - - 105 Drag Strut Attachment Pin
8Z10126- - - 107 Drag Strut Attachment Pin
8Z10127- - - 101 Y oke Attachment Pin
8Z10127- - - 103 Y oke Attachment Pin
8Z10127- - - 105 Y oke Attachment Pin
8Z10127- - - 107 Y oke Attachment Pin
8Z10128- - - 101 Sidebrace Pin
8Z10128- - - 103 Sidebrace Pin
8Z10128- - - 105 Sidebrace Pin
8Z10128- - - 107 Sidebrace Pin
NOTE: Only spares purchased before April 6, 2016 are affected by this service
bulletin. If pins purchased before April 6, 2016 have been installed on
aircraft 4533 and subsequent, then these aircraft are also included in
the effectivity of this service bulletin. Installation of pins purchased
before April 6, 2016 on aircraft that are post MS 4- - - 113997 must be
reworked per this SB before being installed.
B. Reason
Problem: A vendor has disclosed that primer was not applied on certain MLG
attachment pins. A lack of primer can lead to premature corrosion and
structural degradation of the part. A structural failure of the part can lead
to asymmetrical landing gear configurations.
Service bulletin 84- - -54- - -27 applied the incorrect primer.

### Page 6

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 4 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Solution: A detailed visual inspection of the inner bore surface of the Y oke,
Sidebrace and Drag Strut attachment pins is performed for signs of
corrosion.
If no corrosion is found, two coats of F19 and one coat of F13 is applied.
If corrosion is found, the affected pin is removed, the corrosion is removed
and a fluorescent magnetic particle inspection is done for cracks. Two
coats of primer plus F13 is applied to the inner bore surface of the affected
pin if cracks are not found.
If crack indications are found, the affected pin is replaced before next flight.
NOTE: A product improvement was done to add a second coat of chromated
primer to production aircraft via Modsum 4- - - 113997. Unless stated
otherwise, pins that have a single coat of chromated primer conform to
the original intent of the part and are acceptable for continued service.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - Aircraft electrical power is removed
- - - The nose landing gear lock is engaged
- - - The main landing gear lock pins are installed thru each main gear and main gear door
mechanism
- - - Access is gained to the Y oke, Sidebrace and Drag Strut attachment pins located in the
left and right hand nacelle
- - - A detailed visual inspection of the inner bore of the attachment pins is done for signs
of corrosion.
- - - If corrosion is not found, two coats of primer and one coat of F13 is applied to the inner
surface of the pins
- - - If any corrosion is found, the aircraft is placed on jacks and the affected pins are
removed for rework

### Page 7

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 5 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
- - - If corrosion was removed, the inner surface of the affected pins are cleaned and
inspected by a fluorescent magnetic particle inspection (MPI) process for cracking.
If crack indications are not found, two coats of primer and F13 is applied to the inner
bore surface and the affected pins are installed. If crack indications are found, the
affected pins are replaced before next flight
- - - Close out.
D. Compliance
DeHavilland Aircraft of Canada highly recommend that ModSum 4- - - 113997 be
incorporated at the earliest opportunity unless otherwise directed by the operator’s
airworthiness authority.
A Transport Canada Airworthiness Directive is Pending.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
#93- - - Q - - - 02.
This Service Bulletin affects Airworthiness Limitations (AWLs) and/or Damage
T olerance Inspections (DTIs). Reference applicable Post/Pre ModSum 4- - - 113997 and
Service Bulletin 84- - - 54- - - 31 in the Maintenance Requirements Manual.
NOTE: Make sure to track cycles for parts removed and parts installed and
transfer cycles to rework parts.
F . Manpower
It will take an estimated 9.00 man- - -hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 0.50
Procedure 8.00
T e s t/R T S 0.00
Close- - -Out 0.50

### Page 8

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 6 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure time, part fabrication, tool acquisition or lost
time.
G. Material - - - Price and Availability
Kit Number Description
8DK4347- - - 001 Drawing Kit - - - MLG Pins, Nacelle
Drawing Kit(s) (DKs) listed in the table above are drawings only . No parts will be
supplied.
The part(s) and material(s) required are listed in Paragraph 2.A. The parts required
may be either furnished or fabricated from the operator’s existing stock, purchased as
single items from DHC or purchased directly from industry sources. DK parts are to
be manufactured and approved locally (refer to disclaimer in the related text or
illustration). In some cases, an equivalent to the DK part may be available from DHC
under the production part number shown as reference in Parts Required Per Aircraft.
See the contact information below.
DE HAVILLAND AIRCRAFT OF CANADA LIMITED
Material Services
123 Garratt Blvd.
T oronto
Ontario
Canada M3K- - -1Y5
DHC Phone Numbers :
North America:Toll Free: 1 (844) - - - CRC - - - CRC0 (1 (844) 272- - - 2720) or
Direct: 1 (514) 855- - - 8500
DHC Emails:
Parts: Europe, Middle East, Africa, and Russia: emear.parts@dehavilland.com
Americas and Rest of World: parts@dehavilland.com

### Page 9

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 7 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
If required the related 8DK drawings listed in the T able above can be requested by
writing to the email address that follows:
dwg.request@dehavilland.com
Follow the instructions per All Operator Message (AOM) 389.
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Negligible
J. Electrical Load Data
Not affected
K. Publications Affected
Aircraft Maintenance Manual P S M 1 --- 8 4 --- 2.........................
Structural Repair Manual P S M 1 --- 8 4 --- 3............................
Aircraft Illustrated Parts Catalog P S M 1 --- 8 4 --- 4......................
Maintenance Requirement Manual P S M 1 --- 8 4 --- 7....................
ModSums Manual P S M 1 --- 8 4 --- 1 2..................................
L. References
The Revision ‘C’ of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8DK4347 1 B
8Z8457 1 B
8Z8458 1 B
8Z8459 1 D
8Z8460 1 B

### Page 10

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 8 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
ModSum 4Q113997 Rev. ‘H’
ModSum 4- - - 113997 Rev. ‘H’
PCA 45581 Revision 2 (for internal reference only)
ADR ALAC - - - 20- - - 14332820
Transport Canada Airworthiness Directive is Pending.
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Drawing Kit 8DK4347- - - 001, MLG Pins, Nacelle
(2) Detailed Kit Content:
Quantity Per Kit
- - -001
Part Number Description Remarks
AR 85414800- - - 109 Pin see Note below
AR 85414800- - - 111 Pin (Production) see Note 1 be-
low
AR 85414799- - - 109 Pin see Note below
AR 85414799- - - 111 Pin (Production) see Note 1 be-
low
AR 85414794- - - 107 Pin see Note below
AR 85414794- - - 109 Pin (Production) see Note 1 be-
low
AR 85414567- - - 109 Pin see Note below
AR 85414567- - - 111 Pin (Production) see Note 1 be-
low
NOTE: These items are not included in the kit and may be required to install
kit. See drawings 8Z8457, 8Z8458, 8Z8459 and 8Z8560 for potential
requirements.

### Page 11

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 9 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
NOTE 1: These items are not included in the kit and may be required to install
kit. See drawings 8Z8457, 8Z8458, 8Z8459 and 8Z8560 for potential
requirements. Operators have the option to install the production part
numbers directly, no rework required.
The following listed drawings are required for the completion of this service bulletin
and can be requested by writing to the e- - -mail address that follows:
dwg.request@dehavilland.com
DRAWING SHEET
8DK4347 1
8Z8457 1
8Z8458 1
8Z8459 1
8Z8460 1
(3) In addition to the above part(s), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
DeHavilland Aircraft of Canada or purchased directly from industry sources.
Each consumable product listed in the table below is given its own unique
Product ID Number. The number is used to identify a particular recommended
product, the specifications and the trade names any of which can be used
unless specified otherwise (refer to PSM 1- - - 84- - - 18 Consumable Products
Manual).
Consumable
Product ID
Number
Qty. Per
Aircraft
Description Remarks
07- - - 02A 20 oz. F19 Primer DHMS C4.01
07- - - 08 10 oz. F24 Type 4, Class A Polyurethane
Enamel - - - Clear (No Colour), OR,
DHMS C4.04

### Page 12

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 10 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Consumable
Product ID
Number
RemarksDescriptionQty. Per
Aircraft
07- - - 53 10 oz. Type 6, Class B Polyurethane
Enamel - - - Clear (No Colour)
DHMS C4.04
07- - - 01A 10 oz. F13 T ype 1, Grade 3 Soft Film Corro-
sion Preventive Compound
DHMS C4.12
08- - - 12 10 oz. Solvent, Degreaser
(4) The parts listed in the table that follows are not shown in the Consumable
Products Manual and must be procured by the operator as single items from
DeHavilland Aircraft of Canada or purchased directly from industry sources.
Qty. Per Aircraft Parts Description Remarks
8 MS24665- - - 380 Cotter Pin
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
Refer to the EQUIPMENT REQUIRED section of the Special Detailed Inspection of
the Nacelle Pins, LH & RH of this service bulletin.
D. Existing Parts Accountability
- - - for Sidebrace Pins, refer to TABLE 1 of drawings 8Z8457 & 8Z8460
- - - for Drag Strut Pins, refer to TABLE 1 of drawing 8Z8458
- - - for MLG Yoke Pins, refer to TABLE 1 of drawing 8Z8459

### Page 13

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 11 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of DHC in the CRC at 1 (844)
272- - - 2720 (1 (844) CRC - - - CRC0) or email at thd@dehavilland.comfor analysis and to get an
approved disposition to complete this service bulletin.
Part A, for aircraft serial numbers 4001, 4003 - - - 4533 only
A . J o b S e t --- U p
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK’S 24- - - 00- - - 00- - - 861- - - 802 and
24- - - 00- - - 00- - - 910- - - 801).
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set wheel chocks in front and behind the landing gear tires.
(5) Set up the work platforms or ladders as required to gain access to the yoke, side
brace and drag strut attachment pins located in the left and right hand nacelle.
Make sure the work platforms or ladders are electrically grounded.

### Page 14

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 12 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
B. Procedure
(1) Rework Sidebrace Pins.
85414799- - - 107 or 8Z10128- - - 101, 8Z10128- - - 105
85414799- - - 109 or 8Z10128- - - 103, 8Z10128- - - 107
85414800- - - 107 or 8Z10125- - - 101, 8Z10125- - - 105
85414800- - - 109 or 8Z10125- - - 103, 8Z10125- - - 107
as follows:
(refer to Figure 2, Figure 3, Figure 4, Figure 5, drawings 8Z8460 & 8Z8457)
NOTE: If ordering new pins, order pin P/N 85414799- - - 109 and/or
85414800- - - 109, rework in accordance with this SB and part mark in
accordance with drawing 8Z8460 and/or 8Z8457.
NOTE 1: If ordering new production pin, order pin P/N 85414799- - - 111 and/or
85414800- - - 111, no rework is required, refer to drawing 8Z8460 and/or
8Z8457.
(a) Refer to the applicable steps in AMM TASK 32- - - 11- - - 16- - - 000- - - 801 and remove
& discard cotter pins to gain access to the inner bore surface of Sidebrace pins
(referenced above) located in the left and right hand nacelle.
(b) Refer to the applicable steps in AMM TASK 32- - - 11- - - 16- - - 000- - - 801 and remove
the lock swivel assembly from Sidebrace attachment pins (referenced above).
(c) Solvent clean inner surface of Sidebrace pins (referenced above) per SRM
T A S K 5 1 --- 2 6 --- 0 0 --- 0 2 --- 0 1 .
(d) Do a detailed visual inspection of the inner surface of Sidebrace pins
(referenced above) for signs of corrosion.
(e) If no corrosion is found, refer to SRM TASK 51- - - 25- - - 10- - - 02- - - 01 and apply two
coats of F19 Primer (CPM Product ID Number 07- - -02A) to the bore surface of
the affected pin(s) and proceed to step (h).
(f) If corrosion is found on any of the following pins 8Z10128- - - 105, 8Z10128- - - 107,
8Z10125- - - 105, 8Z10125- - - 107 replace the pin with a serviceable pin (P/N
8Z8460- - - xxx and/or 8Z8457- - - xxx, where xxx is the part dash number per
drawing 8Z8460 and/or 8Z8457).

### Page 15

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 13 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
(g) If corrosion is found in any other pin(s), refer to the steps that follow and do the
rework of the pin(s).
1 Refer to AMM T A S K 0 7 --- 1 0 --- 0 0 --- 5 8 2 --- 8 0 1 o r A M MTASK
07- - - 10- - - 00- - - 582- - - 805 and put the aircraft on jacks.
2 Refer to the applicable steps in AMM TASK 32- - - 11- - - 16- - - 000- - - 801 and
remove the affected pin(s).
3 Refer to AMM TASK 51- - - 27- - - 00- - - 910- - - 801 and clean the inner surface of
the affected pin(s) with solvent 08- - - 12.
4 Refer to the applicable steps in the REWORK INSTRUCTIONS of drawing
8Z8460 & 8Z8457 and remove the corrosion.
NOTE: If depth of rework to remove corrosion exceeds 0.005 inches, replace
the pin with a serviceable pin (P/N 8Z8460- - - xxx and/or 8Z8457- - - xxx,
where xxx is the part dash number per drawing 8Z8460 and/or
8Z8457).
5 After corrosion removal, refer to the pages that follow and do theSPECIAL
DETAILED INSPECTION OF THE NACELLE PINS, LH & RH on any
affected Sidebrace pin(s).
a If any crack indications are found, the pin must be replaced before
next flight.
b Replace the pin with a serviceable pin (P/N 8Z8460- - -xxx and/or
8Z8457- - - xxx, where xxx is the part dash number per drawing 8Z8460
and/or 8Z8457).
c If crack indications are not found, refer to SRM TASK
5 1 --- 2 5 --- 1 0 --- 0 2 --- 0 1 a n d a p p l y t w o c o a t s o f F 1 9 P r i m e r ( C P M
Product ID Number 07- - -02A) to the bore surface of the affected
pin(s).
(h) After the application of epoxy primer, refer to the applicable steps in the
REWORK INSTRUCTIONS of drawings 8Z8460 & 8Z8457 and part mark the
reworked pin(s) accordingly.

### Page 16

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 14 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
(i) Refer to the applicable steps in AMM TASK 32- - - 11- - - 16- - - 400- - - 801 and install
either a new/reworked pin(s) or reworked (existing) pin(s) in accordance with
the above steps using a new cotter pin.
(j) Apply one coat of F13 Corrosion Preventive Compound (CPM Product ID
Number 07- - - 01A) to the bore surface of the affected pin(s).
(k) Refer to the applicable steps in AMM TASK 32- - - 11- - - 16- - - 400- - - 801 and install
the lock swivel assembly to the Sidebrace attachment pins (referenced above).
Install nuts and washers (if removed) and cotter pins P/N MS24665- - - 380.
(2) Rework Drag Strut Attachment Pins.
85414794- - - 105 or 8Z10126- - - 101, 8Z10126- - - 105
85414794- - - 107 or 8Z10126- - - 103, 8Z10126- - - 107
as follows:
(refer to Figure 6, Figure 7 and drawing 8Z8458)
NOTE: If ordering new pins, order pin P/N 85414794- - - 107, rework in
accordance with this SB and part mark in accordance with drawing
8Z8458.
NOTE 1: If ordering new production pin, order pin P/N 85414794- - - 109, no
rework is required, refer to drawing 8Z8458.
(a) Refer to the applicable steps in AMM TASK 32- - - 11- - - 11- - - 000- - - 801 and remove
& discard cotter pins to gain access to the inner bore surface of drag strut
attachment pins (referenced above) located in the left and right hand nacelle.
(b) Refer to the applicable steps in AMM TASK 32- - - 11- - - 11- - - 000- - - 803 and remove
the brake swivel assembly from drag strut attachment pins (referenced above).
(c) Solvent clean inner surface of pins per SRM TASK 51- - - 26- - - 00- - - 02- - - 01.
(d) Do a detailed visual inspection of the inner surface of drag strut attachment pins
(referenced above) for signs of corrosion.
(e) If no corrosion is found, refer to SRM TASK 51- - - 25- - - 10- - - 02- - - 01 and apply two
coats of F19 Primer (CPM Product ID Number 07- - -02A) to the bore surface of
the affected pin(s) and proceed to step (h).
(f) If corrosion is found on any of the following pins 8Z10126- - - 105, 8Z10126- - - 107,
replace the pin with a serviceable pin (P/N 8Z8458- - -xxx, where xxx is the part
dash number per drawing 8Z8458).

### Page 17

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 15 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
(g) If corrosion is found in any other pin(s), refer to the steps that follow and do the
rework of the pins.
1 Refer to AMM T A S K 0 7 --- 1 0 --- 0 0 --- 5 8 2 --- 8 0 1 o r A M MTASK
07- - - 10- - - 00- - - 582- - - 805 and put the aircraft on jacks.
2 Refer to AMM TASK 32- - - 11- - - 11- - - 000- - - 801 and remove the affected
pin(s).
3 Refer to AMM TASK 51- - - 27- - - 00- - - 910- - - 801 and clean the inner surface of
the affected pin(s) with solvent 08- - - 12.
4 Refer to the applicable steps in the REWORK INSTRUCTIONS of drawing
8Z8458 and remove the corrosion.
NOTE: If depth of rework to remove corrosion exceeds 0.005 inches, replace
the pin with a serviceable pin (P/N 8Z8458- - -xxx, where xxx is the part
dash number per drawing 8Z8458).
5 After corrosion removal, refer to the pages that follow and do theSPECIAL
DETAILED INSPECTION OF THE NACELLE PINS, LH & RH on any
affected drag strut attachment pin(s).
a If any crack indications are found, the pin must be replaced before
next flight.
b Replace the pin with a serviceable pin (P/N 8Z8458- - -xxx, where xxx is
the part dash number per drawing 8Z8458).
c If crack indications are not found, refer to SRM TASK
5 1 --- 2 5 --- 1 0 --- 0 2 --- 0 1 a n d a p p l y t w o c o a t s o f F 1 9 P r i m e r ( C P M
Product ID Number 07- - -02A) to the bore surface of the affected
pin(s).
(h) After the application of epoxy primer, refer to the applicable steps in the
REWORK INSTRUCTIONS of drawing 8Z8458 and part mark the reworked pins
accordingly.
(i) Refer to the applicable steps in AMM TASK 32- - - 11- - - 11- - - 400- - - 801 and install
the reworked pin(s) using a new cotter pin.
(j) Apply one coat of F13 Corrosion Preventive Compound (CPM Product ID
Number 07- - - 01A) to the bore surface of the affected pin(s).

### Page 18

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 16 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
(k) Refer to AMM TASK 32- - - 11- - - 11- - - 400- - - 803 and install the brake swivel
assembly to drag strut attachment pins (referenced above).
Install nuts and washers (if removed) and cotter pins P/N MS24665- - - 380.
(3) Rework Yoke Attachment Pins,
85414567- - - 107 or 8Z10127- - - 101, 8Z10127- - - 105
85414567- - - 109 or 8Z10127- - - 103, 8Z10127- - - 107
as follows:
(refer to Figure 8, Figure 9 and drawing 8Z8459)
NOTE: If ordering new pins, order pin P/N 85414567- - - 109, rework in
accordance with this SB and part mark in accordance with drawing
8Z8459.
NOTE 1: If ordering new production pin P/N, order P/N 85414567- - - 111, no
rework is required, refer to drawing 8Z8459.
(a) Remove access panels 413BR, 413BL, 423BL and 423BR.
(b) Refer to AMM TASK 0 7 --- 1 0 --- 0 0 --- 5 8 2 --- 8 0 1or AMM TASK
07- - - 10- - - 00- - - 582- - - 805 and put the aircraft on jacks.
(c) Refer to applicable steps in AMM T ask 32- - - 11- - - 21- - - 000- - - 801 and remove the
affected pins.
(d) Solvent clean inner surface of pins per SRM TASK 51- - - 26- - - 00- - - 02- - - 01.
(e) Do a detailed visual inspection of the inner surface and shoulder of yoke
attachment pins (referenced above) for signs of corrosion.
(f) If no corrosion is found, refer to SRM TASK 51- - - 25- - - 10- - - 02- - - 01 and apply two
coats of F19 Primer (CPM Product ID Number 07- - -02A) to the bore surface of
the affected pin(s) and proceed to step (i).
(g) If corrosion is found on any of the following pins 8Z10127- - - 105, 8Z10127- - - 107,
replace the pin with a serviceable pin (P/N 8Z8459- - -xxx, where xxx is the part
dash number per drawing 8Z8459).
(h) If corrosion is found in any other pin(s), refer to the steps that follow and do the
rework of the pins.
1 Refer to the applicable steps in the REWORK INSTRUCTIONS of drawing
8Z8459 and remove the corrosion.
NOTE: If depth of rework to remove corrosion to the bore exceeds 0.005
inches, replace the pin with a serviceable pin (P/N 8Z8459- - - xxx, where
xxx is the part dash number per drawing 8Z8459).

### Page 19

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 17 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
NOTE: If corrosion on the shoulder of the pin cannot be removed within the
limits specified, replace the pins, contact THD or rework in accordance
w i t h S R M T A S k 5 4 --- 4 0 --- 2 5 --- 0 2 --- 0 1 .
2 After corrosion removal, refer to the pages that follow and do theSPECIAL
DETAILED INSPECTION OF THE NACELLE PINS, LH & RH on any
affected yoke attachment pins.
a If any crack indications are found, the pin must be replaced before
next flight.
b Replace the pin with a serviceable pin (P/N 8Z8459- - -xxx, where xxx is
the part dash number per drawing 8Z8459).
c If crack indications are not found, refer to SRM TASK
5 1 --- 2 5 --- 1 0 --- 0 2 --- 0 1 a n d a p p l y t w o c o a t s o f F 1 9 P r i m e r ( C P M
Product ID Number 07- - - 02A) to the bore and shoulder surface of the
affected pin(s).
(i) After the application of epoxy primer, refer to the applicable steps in the
REWORK INSTRUCTIONS of drawing 8Z8459 and part mark the reworked pins
accordingly.
(j) Refer to the applicable steps in AMM TASK 32- - - 11- - - 21- - - 400- - - 801 and install
the reworked pin(s) using kept nut and washer and new cotter pin
MS24665- - - 380.
(k) Refer to AMM TASK 32- - - 11- - - 21- - - 400- - - 801 and install nuts and washers that
were removed to gain access to the inner bore surface of the yoke attachment
pins. Install nuts and washers with cotter pins MS24665- - - 380.
(l) Apply one coat of F13 Corrosion Preventive Compound (CPM Product ID
Number 07- - - 01A) to the bore surface of the pin(s).
(m) Re- - - install access panels 413BL, 413BR, 423BL and 423BR.
C. Close Out
(1) Refer to AMM TASK 29- - - 10- - - 00- - - 870- - - 802 and bleed the No. 2 Hydraulic
System.
(2) Refer to AMM TASK 32- - - 31- - - 00- - - 710- - - 801 and do an operational test of the
landing gear primary extension and retraction system.

### Page 20

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 18 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
( 3 ) R e f e r t o A M M T A S K 0 7 --- 1 0 --- 0 0 --- 5 8 2 --- 8 0 1 o r A M M T A S K 0 7 --- 1 0 --- 0 0 --- 5 8 2 --- 8 0 5
and lower the aircraft from the jacks.
(4) Remove all tools and equipment from the work area.
(5) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.
NOTE: The pins in this service bulletin are Life Limited (reference PSM
1- - -84- - -7). If the pins are re- - -assigned to a different aircraft than the
original installation, the life of the pins must continue to be tracked
separately from the aircraft. Any pin that is reworked must be assigned
the same accumulated cycles as the pin before rework.
Part B, for aircraft serial numbers 4583, 4584, 4585, 4587, 4588 and 4590 only
A . J o b S e t --- U p
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK’S 24- - - 00- - - 00- - - 861- - - 802 and
24- - - 00- - - 00- - - 910- - - 801).
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.

### Page 21

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 19 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
(3) Make sure the nose gear ground lock is engaged.
(4) Set wheel chocks in front and behind the landing gear tires.
(5) Set up the work platforms or ladders as required to gain access to the yoke
attachment pins located in the left and right hand nacelle. Make sure the work
platforms or ladders are electrically grounded.
B. Procedure
(1) Remove access panels 413BR, 413BL, 423BL and 423BR.
(2) Re- - - part mark yoke attachment pin 85414567- - - 109 as 8Z8459- - - 103 per AMM
T ask 20- - - 00- - - 01- - - 910- - - 802.
(3) Re- - - install access panels 413BL, 413BR, 423BL and 423BR.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum, make an entry that conforms to local
regulatory requirements in the applicable logbook(s). Enter component serial
numbers if applicable. Enter this ModSum number only after complete and
functional incorporation of all work defined in this service bulletin.
NOTE: The pins in this service bulletin are Life Limited (reference PSM
1- - -84- - -7). If the pins are re- - -assigned to a different aircraft than the
original installation, the life of the pins must continue to be tracked
separately from the aircraft. Any pin that is reworked must be assigned
the same accumulated cycles as the pin before rework.

### Page 22 (OCR)

SERVICE BULLETIN 84-54-31
SPECIAL DETAILED INSPECTION OF THE NACELLE PINS, LH & RH
1. EFFECTIVITY:
Bombardier Dash 8-400
2. MRM TASK:
TBD
3. AREA DESCRIPTION:
LH & RH Nacelle
Refer to Figures 1, 2, 4, 6 and 8.
4. PURPOSE:
To detect surface cracks in the internal diameter of the pins as shown in
Figures 3, 5, 7 and 9.
5. ZONE:
Refer to Figures 1, 2, 4, 6 and 8.
6. ACCESS:
The following pins are accessed for inspection:
85414799-107 or 8Z10128-101
85414799-109 or 8Z10128-103
85414800-107 or 8Z10125-101
85414800-109 or 8210125-103
85414794-105 or 8Z10126-101
85414794-107 or 8210126-103
85414567-107 or 8210127-101
85414567-109 or 8Z10127-103
7. INSPECTION METHOD:
A. Fluorescent Magnetic Particle Inspection (MPI).
8. EQUIPMENT REQUIRED:
A. Use the items identified as follows or their equivalent (Refer to PSM 1-84-7A NDT Manual
Task 51-00-07-910-801).
NOTE: Equivalent equipment can be used if it satisfies the requirements of this inspection
procedure and can get the required sensitivity.
(1) High intensity UV-A LED Inspection flashlight OPX-365 (SPECTROLINE Company) or
high intensity MidBeam hand held UV LED Light (LABINO Company) that can produce a
minimum black light intensity of 4500 microwatts per square centimeter at 15.0 in (381
mm).
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 20 of 34
JV

### Page 23 (OCR)

SERVICE BULLETIN 84-54-31
Note: High intensity focused UV Light source must be used to detect cracks in the inner
diameter of the pins.
Cellulose sponge or nylon brush, commercially available.
Lint-free cloth, commercially available.
Horizontal wet bench type machine; three phase full wave rectified AC.
Manufacturer "Ardrox", Model: 3505A-6
(5) Fluorescent magnetic particles - "Magnaflux" Magnaglo 14A.
Oil Vehicle - "Magnaflux" Carrier II.
(7) Quantitative Quality Indicator (QQI's), commercially available
(8) Open AC Demagnetizer- "Magnaflux", Model SB-2824.
(9) Residual field strength meter - "Ardrox" MD-220
(10) Noncorrosive, nonabrasive and easily removable marker to mark the location of the
inspection area. The marker must not contain chlorine, lead or graphite (refer to the AMM,
PSM 1-84-2, Chapter 20).
9. PREPARATION:
Prepare the inspection area as follows:
85414799-107 or 8Z10128-101
85414799-109 or 8Z10128-103
85414800-107 or 8Z10125-101
85414800-109 or 8Z10125-103
85414794-105 or 8Z10126-101
85414794-107 or 8Z10126-103
85414567-107 or 8210127-101
85414567-109 or 8Z10127-103
Clean the inspection surfaces (Refer to SRM, PSM 1-84-3, SRM 51-26-00).
Warning: Make sure that there is a good flow of clean air and sufficient fire protection.
Use approved body protection when you use solvents. All solvents are poisonous and
some are flammable
3)  Visually examine pins for cracks, corrosion, damage and other unserviceable conditions.
10. INSPECTION (REFER TO FIGURES 3, 5, 7 AND 9):
A. Equipment performance test and materials verification (Refer to NDTM Part 1, Task 51-00-07):
1) Before the inspection, do the system performance checks for the magnetic particle
bench, lighting, and facilities.
B. Demagnetization:
1)  The parts to be examined must be demagnetized before the inspection. The field strength
meter must not detect residual field that exceeds 3 Gauss anywhere on the part.
C. Set-Up, Magnetic Particle and Magnetization application.
NOTE: Proper sequencing and timing of part magnetization and application of the particle
suspension is required to get optimum indication formation and retention. Apply the
suspension on the part simultaneously with or slightly before energizing the magnetic circuit.
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 21 of 34
JV

### Page 24 (OCR)

SERVICE BULLETIN 84-54-31
NOTE: The use of shims that contain artificial flaws (QQI) is required to make sure the correct
level of magnetism is applied before inspection. Refer to Figures 3, 5, 7 and 9 for the
placement of the QQI.
NOTE: Do not use MPI Equipment that does not detect the flaw indications on the QQI shims.
1. Insert 0.3 in (7.6 mm) diameter central conductor in pins P/N 85414567, P/N 85414799,
P/N 85414800 or 8Z10127, 8Z10128, 8Z10125 and 0.5 in (12.7 mm) diameter central
conductor in pin P/N 85414794 or 8210126 as applicable and put it between the
headstocks firmly with sufficient pressure.
2. Magnetize the pins and use wet continuous method with the current specified in Table 1
Magnetization No.1
NOTE: Apply the magnetization for a minimum of 0.5 second for each application, with
a minimum two applications of magnetizing current.
3. Remove the pin and central conductor from between the head stocks and examine the
entire internal diameter of the pin for cracks.
Note: Typical cracks will be in a longitudinal direction plus or minus 45 degrees.
4. Reinsert 0.3 in (7.6 mm) diameter central conductor in pins P/N 85414567, P/N
85414799, P/N 85414800 or 8Z10127, 8Z10128, 8Z10125 as applicable and put it
between the headstocks firmly with sufficient pressure.
5. Magnetize the pin and use wet continuous method with the current specified in Table 1
Magnetization No.2.
NOTE: Apply the magnetization for a minimum of 0.5 second for each application, with
a minimum two applications of magnetizing current.
6. Remove the pin and central conductor from between the head stocks and examine the
entire internal diameter of the pin for cracks.
Note: Typical cracks will be in a longitudinal direction plus or minus 45 degrees.
7. Place pin P/N 85414567, P/N 85414794, P/N 85414800, P/N 85414799 or 8Z10127,
8Z10128, 8Z10125, 8Z10126 as applicable against the coil inside diameter with the Pin
length parallel to the coil center line.
8. Magnetize the pin and use wet continuous method with the current shown in Table 1
Magnetization 3.
NOTE: Apply the magnetization for a minimum of 0.5 second for each application, with
a minimum two applications of magnetizing current.
Examine the entire internal diameter of the pin.
NOTE: Typical cracks will be in circumferential direction plus or minus 45 degrees.
Table 1
Inspection data for Pins
85414567-107 or 8Z10127-101
85414567-109 or 8Z10127-103
Magnetization  Circular Magnetization-  Longitudinal Magnetization-
Conductor  Contact  Coil - 5 Turns
1  500 A
2  800A  4000A
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 22 of 34
JV

### Page 25 (OCR)

SERVICE BULLETIN 84-54-31
Inspection data for Pins
85414794-105 or 8Z10126-101
85414794-107 or 8210126-103
Magnetization  Circular Magnetization-  Longitudinal Magnetization-
No.  DC
Conductor  Contact  Coil - 5 Turns
800A
2
3600A
Inspection data for Pins
85414800-107 or 8Z10125-101
85414800-109 or 8Z10125-103
Magnetization  Circular Magnetization-  Longitudinal Magnetization-
No.  DC
Conductor  Contact  Coil - 5 Turns
1  600A
2  1000A
З  4000A
Inspection data for Pins
85414799-107 or 8Z10128101
85414799-109 or 8Z10128-103
Magnetization  Circular Magnetization-  Longitudinal Magnetization-
No.  DC  DC
Conductor  Contact  Coil - 5 Turns
1  500A
2  800A
З  3500A
11. INDICATION EVALUATION:
A. Non-relevant indications caused by magnetic leakage fields do not represent discontinuities.
B. Design factors such as keyways, drilled holes, abrupt changes in section, metallurgical
changes, permeability variation, damaged coating or dissimilar materials can produce non-
relevant indications.
C. False indications are not caused by leakage field, they are caused mechanically. These
indications do not reappear after the parts are cleaned and reprocessed.
D. Relevant indications are caused by magnetic leakage fields and represent the presence of a
discontinuity and will reappear after the part is cleaned and reprocessed.
E. Surface indications are sharp and distinct.
F. Slightly subsurface indications are broad and fuzzy.
12. ACCEPTANCE / REJECTION CRITERIA:
A. Any crack indication is cause for rejection.
13. REPORTING:
A. Report all defect and reject indications to Bombardier Aerospace (Toronto) on the "Dash 8-400
Aircraft Structural Defect Report" (Refer to the Nondestructive Testing Manual (NDTM), PSM
1-84-7A, Appendix A).
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 23 of 34
JV

### Page 26 (OCR)

SERVICE BULLETIN 84-54-31
14. POST INSPECTION REQUIREMENTS:
A. Pins must be demagnetized after the final inspection. The field strength meter must not detect
residual fields exceeding 3 Gauss anywhere on the part (Refer to NDTM Part 1, Task 51-00-
B. Pins must be cleaned to remove all traces of magnetic particle residue (Refer to SRM, (PSM 1-
84-3), SRM 51-26-00).
C. After removal of the magnetic residues, examine the Pin surface with a white and black light.
Make sure that no traces of magnetic residue are visible. If there is residue, clean the Pin until
all traces are removed.
15. CLOSE-UP:
A. If the finish in the inspection area was removed, apply the finish again (Refer to SRM, (PSM 1-
84-3), SRM 51-20-10-00-01).
B. Remove all tools, equipment and unwanted materials from inspection area.
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 24 of 34
JV

### Page 27

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 25 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Location of Inspection / Rework
F i g u r e1
LOCATION OF MLG PINS

### Page 28

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 26 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Location of Sidebrace Attachment Pins
85414799- - - 107, 8Z10128- - - 101, 8Z10128- - - 105
85414799- - - 109, 8Z10128- - - 103, 8Z10128- - - 107
F i g u r e2
Sidebrace Attachment Pin
A
A

### Page 29

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 27 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Sidebrace Attachment Pins - - - Special Detailed Inspection
85414799- - - 107 or 8Z10128- - - 101, 85414799- - - 109 or 8Z10128- - - 103
F i g u r e3
Central Conductor 0.3 ² dia.
- - - QQI Placement
LEGEND

### Page 30 (OCR)

SERVICE BULLETIN 84-54-31
Sidebrace Attachment
Pin
Location of Sidebrace Attachment Pins
85414800-107, 8Z10125-101, 8Z10125-105
85414800-109, 8Z10125-103, 8Z10125-107
Figure 4
01 May 2019  S.B. 84-54-31
Revision 'C' 15 Mar 2021  Page 28 of 34
JV

### Page 31

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 29 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Sidebrace Attachment Pins - - - Special Detailed Inspection
85414800- - - 107 or 8Z10125- - - 101, 85414800- - - 109 or 8Z10125- - - 103
F i g u r e5
Central Conductor 0.3 ² dia.
- - - QQI Placement
LEGEND

### Page 32

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 30 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Location of Drag Strut Attachment Pins
85414794- - - 105, 8Z10126- - - 101, 8Z10126- - - 105
85414794- - - 107, 8Z10126- - - 103, 8Z10126- - - 107
F i g u r e6
A
A
B
B

### Page 33

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 31 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Drag Strut Attachment Pins - - - Special Detailed Inspection
85414794- - - 105 or 8Z10126- - - 101, 85414794- - - 107 or 8Z10126- - - 103
F i g u r e7
No.1 No.1
- - - QQI Placement
LEGEND

### Page 34

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 32 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Location of Yoke Attachment Pins
85414567- - - 107, 8Z10127- - - 101, 8Z10127- - - 105
85414567- - - 109, 8Z10127- - - 103, 8Z10127- - - 107
F i g u r e8
A
A
A

### Page 35

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 33 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
Y oke Attachment Pins - - - Special Detailed Inspection
85414567- - - 107 or 8Z10127- - - 101, 85414567- - - 109 or 8Z10127- - - 103
F i g u r e9
Central Conductor 0.3 ² dia.
- - - QQI Placement
LEGEND
1

### Page 36

SERVICE BULLETIN 84- - -54- - -31
S . B . 8 4 --- 5 4 --- 3 1
Page 34 of 34
01 May 2019
JVRevision ‘C’ 15 Mar 2021
This Page Intentionally Blank
1

### Page 37

Oct 2019
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
DASH 8 AIRCRAFT
To : CMDB Focal
Email: cmdb.request@dehavilland.com
From:
Company:
Phone: Extn:
Facsimile: Date:
Email:
The data that you provide below will help us record the incorporation of this Service
Bulletin and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Email PDF to:
cmdb.request@dehavilland.com

### Page 38

Oct 2019
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - DASH 8 AIRCRAFT
To : SB Focal, DE HAVILLAND AIRCRAFT OF CANADA LIMITED
Phone: 1 (416) 373 - - -5098
Email: george.moffatt@dehavilland.com
From:
Company:
Phone: Extn:
Facsimile: Date:
Email:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Email PDF to:
george.moffatt@dehavilland.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
