# De Havilland Canada Service Bulletin 84-55-11

Copy: No revision named ("84-55-11"), 22 pages: PDF https://openairdocs.org/files/sha256/56/63/5663259c0a4e4e714326be9c04538aa3c687aa51686c0eb3e3b21cc918b44674; text https://openairdocs.org/service-documents/bombardier/sb-84-55-11/file/5663259c0a4e.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1403; AD 2023-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md) (issued as De Havilland Canada)
- Type: Service bulletin (Service Bulletin)
- Number: 84-55-11
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-55-11

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-07-06](https://openairdocs.org/ad/2023-07-06.md), effective Jun 20, 2023: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-84-55-11/proposed.md).

## Text (22 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1403; AD 2023-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 1 of 20
SERVICE BULLETIN
ATA SYSTEM: 5510 N U M B E R : 8 4 --- 5 5 --- 1 1
SUBJECT : Horizontal Stabilizer - - - Replacement of Corroded Lower Center Skin
Panel - - - ModSum 4 - - -114029
1. PLANNING INFORMA TION
A. Effectivity
Aircraft Affected:
In- - -Service: DHC - - - 8 Aircraft Models 401 and 402 Serial Numbers 4001,
4003 thru 4549.
Production: ModSum 4- - - 180048 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4550 thru
subsequent. This Modsum is superceded by Production
Modsum 4- - - 180061.
Production: ModSum 4- - - 180061 will be installed before delivery on
applicable DHC- - -8 Aircraft at Serial Number 4635 and
subsequent.
Related
ModSum
Title
4- - - 113903 Horizontal Stabilizer - - - Lower Skin, Center Section,
Inspection For Corrosion and Addition of Corrosion
Protection (SB84- - -55- - -05)
4- - - 180048 Horizontal T ail - - - Lower Center Skin, Raw Material
Change and Addition of (F24) T op Coat (Y605D
- - - 6.00 to Y605D +6.00)
4- - - 180061 Horizontal T ail - - - Lower Center Skin, Raw Material
Thickness Revised and Specification Updated

### Page 2

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 2 of 20
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery on the aircraft or as
changed by DHC Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this
bulletin can be completed.
Spares Affected:
The following is a list of spares affected by this change. Review spares and
procurement systems to determine the existence of any listed parts. See
Paragraph 2.D., Existing Parts Accountability , for disposition.
Part Number Description
85517250- - - 103 Skin Panel
B. Reason
Problem: Several operators of the DHC8- - -400 aircraft reported advanced corrosion
on the inside surface of the horizontal tail lower center skin panel.
Structural degradation and loss of strength may occur if the corrosion is
left untreated.
Solution: This service bulletin provides instructions to replace the existing horizontal
stabilizer lower center skin panel with a new lower center skin panel that
is intended to be used for those skins where the corrosion is beyond
acceptable limits. The new lower center skin is treated with alodine,
chromate epoxy primer and additional layer of polyurethane enamel paint
and a layer of F13 moisture displacement compound.
NOTE: Both MODSUM 4- - - 180048 and MODSUM 4- - - 180061 give enhanced
corrosion protection and are acceptable production configurations that
are not applicable to this rework.

### Page 3

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 3 of 20
C. Description
The procedures in this service bulletin give the instructions to do the tasks that follow:
- - - Aircraft electrical power is removed
- - - The nose landing gear lock is engaged
- - - The main landing gear lock pins are installed through each main gear and main gear
door mechanism
- - - The horizontal stabilizer is removed
- - - The elevators are removed
- - - Access is gained to the front spar inspection hole outboard of the rib #1 and similarly
the rear shroud access panel to reach the rear spar inspection hole adjacent to rib #1
- - - The existing skin splices are removed and retained
- - - The existing corroded lower center skin panel and stringers are removed and
discarded from the horizontal stabilizer
- - - The new lower center skin panel and stringers are installed on the horizontal stabilizer
- - - The existing skin splices are re- - -installed on the horizontal stabilizer
- - - The lower center skin panel is treated with grey polyurethane enamel and moisture
displacement compound
- - - The skin panel assembly is part marked after the completion of the retrofit
- - - The elevators are installed
- - - The horizontal stabilizer is installed
- - - Close out.
D. Compliance
De Havilland Aircraft of Canada Limited highly recommends incorporation of ModSum
4- - - 114029 unless otherwise directed by the operator’s airworthiness authority, only
after the damage has been evaluated by DE HAVILLAND OF CANADA LIMITED
In- - -Service Engineering and deemed it necessary to replace the skin.
E. Approval
The technical content of this service bulletin has been approved under the authority of
the Transport Canada Civil Aviation (TCCA) Design Approval Organization No: DAO
#19- - - Q - - - 01.

### Page 4

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 4 of 20
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
F . Manpower
It will take an estimated 108.00 man- - - hours to complete this service bulletin. The
breakdown of the man- - -hours is shown in the table that follows:
TASK M A N --- H O U R S
J o b S e t --- U p 1.00
Procedure 106.0
T e s t/R T S 0.00
Close- - -Out 1.00
This estimate is for direct labour done by an experienced crew and it does not
include, planning, familiarization, cure time, part fabrication, tool acquisition or lost
time.
G. Material - - - Price and Availability
The ModKit required to do this service bulletin is listed in the table below.
Kit Number Description
8MK4903- - - 001 Kit - - - Replacement of Corroded Lower
Center Skin Panel - - - Horizontal
Stabilizer
Operators should submit a purchase order through the Customer Response Center
(CRC) to the Customer Accounts Service T eam (CAST) at DHC specifying aircraft
serial number(s). Submit the purchase order to:
De Havilland Aircraft of Canada Limited
Material Services
123 Garratt Blvd.
T oronto
Ontario
Canada M3K- - -1Y5

### Page 5

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 5 of 20
DHC Phone Numbers :
North America:Toll Free: 1 (844) - - - CRC - - - CRC0 (1 (844) 272- - - 2720) or
Direct: 1 (514) 855- - - 8500
DHC Emails:
Parts: Europe, Middle East, Africa, and Russia: emear.parts@dehavilland.com
Americas and Rest of World: parts@dehavilland.com
H. T ooling - - - Price and Availability
None
I. Weight and Balance
Not affected
J. Electrical Load Data
Not affected
K. Publications Affected
Aircraft Illustrated Parts Catalog P S M 1 --- 8 4 --- 4......................
ModSums Manual P S M 1 --- 8 4 --- 1 2..................................
L. References
The initial issue of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING SHEET REV
8MK4903 1 B
8Z7332 1 D
8Z7332 2 B
8Z7332 3 A
NOTE: Refer to Figure 1 for the list of aircraft within the service effectivity range
that have modified horizontal stabilizer attachment hardware should the
need arise to procure these parts in case of damage or loss.

### Page 6

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 6 of 20
ModSum 4Q114029 Rev. ‘F’
ModSum 4- - - 114029 Rev. ‘F’
PCA 45486 Revision 1 (for internal reference only).
2. MATERIAL INFORMA TION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4903- - - 001
(2) Detailed Kit Content:
Quantity Per Kit
- - -001
Part Number Description Remarks
65 B0205016AD5- - - 7S Rivet See NOTE below
40 B0205016AD5- - - 5S Rivet See NOTE below
150 B0206017TP8 Collar Hi- - -Lite See NOTE below
80 B0206017TP6 Collar Hi- - -Lite See NOTE below
270 B0206017TP5 Collar Hi- - -Lite See NOTE below
10 B0206016CY8 Collar Hi- - -Lite See NOTE below
20 B0206016CY6 Collar Hi- - -Lite See NOTE below
10 B0206003AG8- - - 12 Pin Hi- - -Lite
14 B0206003AG8- - - 11 Pin Hi- - -Lite
16 B0206003AG8- - - 10 Pin Hi- - -Lite
14 B0206003AG8- - - 9 Pin Hi- - -Lite
36 B0206003AG8- - - 8 Pin Hi- - -Lite
6 B0206003AG8- - - 7 Pin Hi- - -Lite
36 B0206003AG8- - - 6 Pin Hi- - -Lite
4 B0206003AG8- - - 5 Pin Hi- - -Lite
34 B0206003AG6- - - 11 Pin Hi- - -Lite
2 B0206003AG6- - - 10 Pin Hi- - -Lite
34 B0206003AG6- - - 8 Pin Hi- - -Lite
2 B0206003AG6- - - 6 Pin Hi- - -Lite
10 B0206003AG5- - - 10 Pin Hi- - -Lite

### Page 7

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 7 of 20
Quantity Per Kit
- - -001
RemarksDescriptionPart Number
12 B0206003AG5- - - 9 Pin Hi- - -Lite
8 B0206003AG5- - - 8 Pin Hi- - -Lite
18 B0206003AG5- - - 7 Pin Hi- - -Lite
34 B0206003AG5- - - 6 Pin Hi- - -Lite
62 B0206003AG5- - - 5 Pin Hi- - -Lite
68 B0206003AG5- - - 4 Pin Hi- - -Lite
30 B0206003AG5- - - 3 Pin Hi- - -Lite
6 B0206001AG8- - - 7 Pin Hi- - -Lite
8 B0206001AG6- - - 8 Pin Hi- - -Lite
8 B0206001AG6- - - 5 Pin Hi- - -Lite
2 85517252- - - 101 Stringer 3, 4
2 85517251- - - 101 Stringer 1A, 5A
1 85517250- - - 107 Skin Panel
NOTE: Hardware quantity increased by approximately 10% to account for losses.
See retrofit drawing 8Z7332 for actual quantity.
NOTE: The kits are only to be ordered after In- - -Service engineering has
evaluated the corrosion and deemed it necessary to replace the skin.
Listed drawings that are required to complete the kit above can be requested by
writing to the following email address:
dwg.request@dehavilland.com
(3) In addition to the above part(s), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
DHC or purchased directly from industry sources.
Each consumable product listed in the table below is given its own unique
Product ID Number. The number is used to identify a particular recommended
product, the specifications and the trade names any of which can be used
unless specified otherwise (refer to PSM 1- - - 84- - - 18, Consumable Products
Manual).

### Page 8

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 8 of 20
Consumable
Product ID
Number
Qty. Per Aircraft Description Remarks
06- - - 01 A/R Sealant, T empera-
ture Resistant, Inte-
gral Fuel T anks,
High Adhesion
DHMS S3. 01/B2
06- - - 02 A/R Sealant, Corrosion
Inhibiting
DHMS S3. 06 C - - - 80
MIL - - - PRF- - - 81733
(See Note below)
07- - - 01 A/R Compound, F13,
Corrosion Inhibit-
ing Coating- - -Cor-
rosion Preventive,
Clear, Soft Film
MIL - - - C - - - 16173 GR.3
(F13)
07- - - 02 A/R Primer, Fluid - - -Re-
sistant, Chromated
Epoxy
MIL - - - P - - - 23377
(F19)
07- - - 29A A/R Coating, Chemical
Conversion (Manu-
al Application)
M I L --- C --- 5 5 4 1
C1 Alodine
--- --- A/R Polyurethane
Enamel
MIL - - - C - - - 83286
F24 Grey
NOTE: Alternative: Proseal P/S 870 C - - - 12 Sealant to MIL - - - PRF- - - 81733.
B. Parts Required to Modify Spares
None
C. Special T ools and Equipment Required
None

### Page 9

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 9 of 20
D. Existing Parts Accountability
Existing
Part Number Description Qty. IC DC
New Part
Number PNC
85517250- - - 103 Skin Panel 1 C DIS 85517250- - - 107 S
IC Interchangeability Code
A Not interchangeable.
B Removed Part. No direct replacement.
C Conditionally Interchangeable. Installation of superseded part negates the
intent of this service bulletin.
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator’s stores for salvage consideration.
PNC Part Number Code
N No equivalent DHC part number for reworked part. Indicate on part that
this service bulletin has been accomplished.
R Part number after rework.
S Superseding or equivalent part number.
X Reworked part and superseding part are functionally and physically
equivalent but not identical.
3. ACCOMPLISHMENT INSTRUCTIONS
If it is not possible to complete all the instructions of this service bulletin because of the
configuration of the aircraft, speak with a representative of DHC in the CRC at 1 (844)
272- - - 2720 (1 (844) CRC - - - CRC0) or email at thd@dehavilland.comfor analysis and to get an
approved disposition to complete this service bulletin.

### Page 10

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 10 of 20
A . J o b S e t --- U p
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS ON THE MAIN LANDING
GEAR. MAKE SURE YOU ENGAGE THE NOSE GEAR LOCK. IF YOU
DO NOT DO THIS, THE LANDING GEAR CAN ACCIDENTALL Y
RETRACT . THIS CAN CAUSE INJURIES TO PERSONS AND
DAMAGE TO THE EQUIPMENT .
WARNING: MAKE SURE YOU INSTALL THE LOCKPINS IN THE DOOR
MECHANISMS OF THE MLG AND NLG. THE DOOR MECHANISMS
CAN ACCIDENTALL Y CLOSE THE LANDING GEAR DOORS. THIS
CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO THE
EQUIPMENT .
(1) Placard and select all aircraft electrical power to OFF . Obey all relevant
WARNINGS and CAUTIONS (refer to AMM TASK 24- - - 00- - - 00- - - 861- - - 802 and
TASK 24- - - 00- - - 00- - - 910- - - 801).
(2) Make sure that lock pins are installed through each main gear and main gear
door mechanism.
(3) Make sure the nose gear ground lock is engaged.
(4) Set wheel chocks in front and behind the landing gear tires.
B. Procedure
NOTE: Refer to Figure 1 for the list of aircraft within the service effectivity range
that have modified horizontal stabilizer attachment hardware should the
need arise to procure these parts in case of damage or loss.
(1) Remove the horizontal stabilizer from the aircraft (refer to AMM TASK
55- - - 10- - - 00- - - 000- - - 801).
NOTE: Support the stabilizer to allow access to the lower surface.
(2) Remove the elevators (refer to AMM TASK 27- - - 34- - - 01- - - 000- - - 801).
(3) Remove and retain the skin splices 85517260 from the lower center skin panel
85517250 (refer to Figures 2, 3 and 6).

### Page 11

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 11 of 20
(4) Remove and discard the existing lower center skin panel assembly 85517036
including the existing stringers 85517251 and 85517252 and retain the existing
angles 85517319 (refer to Figures 2 to 6).
NOTE: Contact the Dehavilland Aircraft of Canada Limited T echnical Help Desk, if
any corrosion is present on the ribs or other retained parts.
(5) Locate the new stringers 85517251 and 85517252 to the new lower center skin
panel P/N 85517250- - - 107 using pick up holes at each end supplied new lower
center skin panel P/N 85517250- - - 107 or transferring holes from the existing lower
center skin panel P/N 85517250- - - 103 (refer to Figures 2, 3, 4 and 5).
(6) Fay surface seal stringers to the skin panel with the sealant (06- - - 02) (refer to
Figures 2, 3, 4 and 5).
(7) Install the retained angles 85517319 to the stringers 85517251 and 85517252
(refer to Figures 2, 4, 5 and 6).
(8) Install the new lower center skin panel P/N 85517250- - - 107 with the stringers
85517251 and 85517252 to the horizontal stabilizer (refer to Figures 2 to 6).
(9) Install the retained skin splices 85517260 to the lower center skin panel P/N
85517250- - - 107 (refer to Figures 2, 3 and 6).
(10) Solvent wipe clean the moisture displacement compound (07- - - 01) from inside
surfaces and 1 inch up all around (refer to Figures 2, 4 and 6). Make sure the
surfaces are completely clean and dry.
(11) Re- - -finish any scuffed (bare metal) surfaces with the (C1) chemical conversion
coating (07- - - 29A) (refer to SRM TASK 51- - - 21- - - 10- - - 02- - - 01) and (F19) epoxy
primer (07- - - 02) (refer to SRM TASK 51- - - 25- - - 10- - - 02- - - 01 and Figure 2).
(12) Finish the inner surface of the skin and the entire surfaces of the skin stringers
and angles, including over the fasteners around the center section 1 inch up on
the spars, ribs with the (F24) grey polyurethane enamel or equivalent (refer to
Figure 2 and SRM TASK 51- - - 25- - - 15- - - 02- - - 01).

### Page 12

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 12 of 20
CAUTION: MASK OF THE STABILIZER ATTACHMENT PADS (6 PLACES) PRIOR
TO PAINTING. NO (F19) PRIMER OR PAINT ON THESE SURFACES.
(13) Finish the external surface of the skin and the skin splices, including over the
fasteners and sealant with (F24) grey polyurethane enamel or equivalent (refer to
SRM 51- - - 25- - - 15- - - 02- - - 01 and Figure 2).
(14) After the application of (F24) enamel, apply a coat of moisture displacement
compound (07- - - 01) over the entire inner surface of the painted skin, stringers
and the angles and painted area on the spars and ribs (refer to Figure 2 and
AMM TASK 51- - - 25- - - 01- - - 390- - - 801).
NOTE: Overspray onto the existing (F13) is acceptable.
(15) Part mark 8Z7332- - - 001 after completion of the retrofit adjacent to either access
hole on the outside surface of the skin using an indelible ink marker (refer to
Figures 2 and 3).
(16) Install the elevators (refer to AMM TASK 27- - - 34- - - 01- - - 400- - - 801).
(17) Install the horizontal stabilizer (refer to AMM TASK 55- - - 10- - - 00- - - 400- - - 801).
NOTE: If the Aircraft is listed in Figure 1, ensure that the installation is done
according to the listed configuration.
C. Close Out
(1) Remove all tools and equipment from the work area.
(2) On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applicable logbook(s). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.

### Page 13 (OCR)

SERVICE BULLETIN 84-55-11
NOTE
THE FOLLOWING A/C WITHIN THIS SERVICE EFFY RANGE HAVE CERTAIN MODIFIED
HORIZONTAL STABILIZER ATTACHMENT HARDWARE. THIS LIST IS FOR REFERENCE
ONLY SHOULD THE NEED ARISE TO REPLACE ANY OF THESE AFFECTED ITEMST
PRIOR TO RE-ATTACHING THE HORIZONTAL STABILIZER: CONTACT DEHAVILLAND
SPARES DEPT. FOR REPLACEMENT OF ANY OF THESE MODIFIED ITEMS.
A COPY OF THE APPLICABLE MOD CAN BE MADE AVAILABLE UPON REQUEST BYT
CONTACTING A REPRESENTATIVE AT DHC CUSTOMER RESPONSE CENTRE AT
thd@dehavilland.com
A/C 4312 REWORKED BY MOD 4Y123041
A/C 4318 REWORKED BY MOD 4Y123058
A/C 4319 REWORKED BY MOD 4Y123059
A/C 4329 REWORKED BY MOD 4Y123113
A/C 4339 REWORKED BY MOD 4Y123518
A/C 4340 REWORKED BY MOD 4Q110508
A/C 4353 REWORKED BY MOD 4Y123560
A/C 4357 REWORKED BY MOD 4Y123556
A/C 4393 REWORKED BY MOD 4Y123759
A/C 4401 REWORKED BY MOD 4Y123767
A/C 4433 & 4436 REWORKED BY 4Y123880
A/C 4438 REWORKED BY MOD 4Y123879
A/C 4441 TO 4458 & 4460 TO 4476 REWORKED BY MOD 4Y123888
A/C 4446 REWORKED BY MOD 4Y123888 & 4Y123904
A/C 4447 REWORKED BY MOD 4Y123888 & 4Y123914
A/C 4448 REWORKED BY MOD 4Y123888 & 4Y123914
A/C 4451 REWORKED BY MOD 4Y123888 & 4Y123914
A/C 4449 REWORKED BY MOD 4Y123888 & 4Y123925
A/C 4450 REWORKED BY MOD 4Y123888 & 4Y123925
A/C 4494 REWORKED BY 4Y123880
og 6103a08.dg. sk. jun01/2020
Figure 1
S.B. 84-55-11
16 Feb 2021  Page 13 of 20
SB

### Page 14 (OCR)

SERVICE BULLETIN 84-55-11
AREA OF RETROFIT -
_OWER CENTRE SKIN PANEL
110000000
000000000000
LOCATOR VIEW
og6103a03.dg. sk. jun01/2020
S.B. 84-55-11
16 Feb 2021  Page 14 of 20
SB

### Page 15 (OCR)

SERVICE BULLETIN 84-55-11
NOTES:
5. INSTALL HI-LITE FASTENERS PER STRUCTURAL REPAIR MANUAL
PSM 1-84-3 CHAPTER 51-40-15 (INTERFERENCE FIT).  DISCARD EXISTING PINS AND COLLARS.  (HI-LITE FASTENER REMOVAL + INSTALLATIOVE THE PINS WITH
CAUTION TO AVOID DAMAGING THE HOLES.
USE OF OVERSIZE PINS ARE PERMITTED IF OUTSIDE OF THESE
5/32 DIA (.1590 / . 1620)
3/16 DIA (.1850 / . 1880)
1/4 DIA (.2450 /
CONSULT STRUCTURAL REPAIR MANUAL FOR 1st 2nd OVERSIZE
HOLE LIMITS AND PINS / COLLARS.
CONTACT THE DEHAVILLAND AIRCRAFT OF CANADA TECHNICAL
HELP DESK FOR CONDITIONS NOT REFLECTED ON THIS DRAWING
OR CORROSION IS PRESENT ON THE RIBS.
6. REFER TO STRUCTURAL REPAIR MANUAL PSM 1-84-3 CHAPTER
51-42-05 (SOLID RIVET INSTALLATION).
_FAY SURFACE SEAL STRINGERS TO SKIN PANEL WITH DHMS S3.06
I CLASS C-80 SEALANT OR PROSEAL P/S  870 C-12 SEALANT
TO MIL-PRF-81733. SEE FIGURES 4 AND 5 AT VIEW ON ARROW 'C'.
FAY SURFACE SEAL  SPLICES WITH OHMS SKIN PANEL ASSEMBLY TO RIBS.  SPAR CAPS AND
53.06 TYPE 1 CLASS C-80 SEALANT OR PROSEAL
P/S 870 C-12 SEALANT TO MIL-PRF-81733.
THE EXISTING (OLD) SEALANT IS TO BE REMOVED PRIOR TO APPLICATION.  SEE FIGURE 3 AT  'VIEW LOOKING DOWN'
9 VOID SEAL SKIN PANEL BAL F  JOINTS WITH PR1422 B2 SEALANT PER
STRUCTURAL REPAIR MANUAL PSM 1-84-3 CHAPTER 51-23-00.
LO FILLET SEAL AROUND PERIPHERY OF SKIN SPLICES WITH  og6103a01.dg. sk. jun01/2020
SEALANT PER STRUCTURAL REPAIR MANUAL PSM 1-84-3
CHAPTER 51-23-00.
S.B. 84-55-11
16 Feb 2021  Page 15 of 20
SB

### Page 16 (OCR)

SERVICE BULLETIN 84-55-11
A SOLVENT WIPE CLEAN THE (F13) MOISTURE DISPLACEMENT COMPOUND
FROM INSIDE SURFACES & 1" INCH UP ALL AROUND AS SHOWN IN
SECTIONS  'A-A" &  'B-B'. ENSURE THE SURFACES ARE COMPLETELY
DRY CLEAN AND DRY.
12. RE-FINISH ANY SCUFFED (BARE METAL) SURFACES WITH (C1) CHEMICAL
CONVERSION COATING PER STRUCTURAL REPAIR MANUAL PSM 1-84-3
CHAPTER 51-21-10-02-01 AND (F19) EPOXY PRIMER PER STRUCTURAL
REPAIR MANUAL PSM 1-84-3 CHAPTER 51-25-10-02-01.
FINISH THE INNER SURFACE OF THE SKIN AND THE ENTIRE SURFACES
THE SKIN STIFFENERS AND ANGLES,  INCUDING OVER THE FASTENERS
AROUND THE CENTRE SECTION 1" INCH UP ON THE SPARS, AND RIBS
PER SECTION A-A AND B-B WITH (F24) GREY POLYURETHANE ENAMEL
OR EQUIVALENT PER STRUCTURAL REPAIR MANUAL PSM 1-84-3
CHAPTER 51-25-15.
14  FINISH THE EXTERNAL SURFACE OF THE SKIN_AND SKIN SPLICES,
INCLUDING OVER  THE FASTENERS AND SEALANT WITH GREY
POLYURETHANE ENAMEL OR EQUIVALENT PER STRUCTURAL REPAIR
MANUAL PSM 1-84-3 CHAPTER 51-25-15.
CAUTION: MASK OFF  THE STABILIZER ATTACHMENT PADS (6 PLACES)
PRIOR TO PAINTING. NO (F19) PRIMER OR PAINT ON THESE SURFACES.
15.  AFTER THE APPLICATION OF (F24) ENAMEL PER NOTES 13 & 14 APPLY
A COAT OF  (F13) MOISTURE DISPLACEMENT COMPOUND OVER THE
ENTIRE INNER SURFACE OF THE PAINTED SKIN,  STIFFENERS AND
ANGLES,  AND PAINTED AREA ON THE SPARS AND RIBS PER AMM TASK
51-25-01-390-801.
OVERSPRAY ONTO THE EXISTING (F13) IS ACCEPTABLE.
16 PART MARK "8Z7332-001" AFTER COMPLETION OF RETROFIT ADJACENT TO
EITHER ACCESS HOLE AS SHOWN ON FIGURE 3 ON THE OUTSIDE SURFACE
OF THE SKIN USING AN INDELIBLE INK MARKER.  og6103a02.dg. sk, jun01/2020
S.B. 84-55-11
16 Feb 2021  Page 16 of 20
SB

### Page 17

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 17 of 20
Replacement of Lower Center Skin Panel - - -Horizontal Stabilizer- - -Retrofit
F i g u r e3
85517251--101

### Page 18

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 18 of 20
Replacement of Lower Center Skin Panel - - -Horizontal Stabilizer- - -Retrofit
F i g u r e4 85517251--101
85517252--101
85517250--105
85517251--101
85517252--101

### Page 19

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 19 of 20
Replacement of Lower Center Skin Panel - - -Horizontal Stabilizer- - -Retrofit
F i g u r e5
85517251--- 101 85517252--- 10185517252--- 101
85517251--- 101
85517250--- 105

### Page 20

SERVICE BULLETIN 84- - -55- - -11
S . B . 8 4 --- 5 5 --- 1 1
16 Feb 2021
SB
Page 20 of 20
Replacement of lower center skin panel - - - Horizontal stabilizer - - - Retrofit
F i g u r e6
85517250- - - 105
85517250- - - 105
85517251- - - 101
85517252- - - 101
OR

### Page 21

Oct 2019
SERVICE BULLETIN (SB) - - - RECORD OF INCORPORATION
DASH 8 AIRCRAFT
To : CMDB Focal
Email: cmdb.request@dehavilland.com
From:
Company:
Phone: Extn:
Facsimile: Date:
Email:
The data that you provide below will help us record the incorporation of this Service
Bulletin and the aircraft effectivity in the maintenance manual.
Operator: Service Bulletin: __________________ Revision: _________
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Aircraft Serial Number: Model Number: Date Bulletin Completed:
Email PDF to:
cmdb.request@dehavilland.com

### Page 22

Oct 2019
SERVICE BULLETIN (SB) - - - COMMENT SHEET - - - DASH 8 AIRCRAFT
To : SB Focal, DE HAVILLAND AIRCRAFT OF CANADA LIMITED
Phone: 1 (416) 373 - - -5098
Email: george.moffatt@dehavilland.com
From:
Company:
Phone: Extn:
Facsimile: Date:
Email:
Select appropriate box(es) and add comments or suggestions you would like us to know
that may enhance the quality of our service bulletins.
Service Bulletin: Revision: ModSum:
1. PLANNING INFORMATION
V Effectivity V Reason V Description V Compliance
V Approval V Manpower V Material V Weight and Balance
V Electrical Load V T ooling V References V Publications Affected
2. MATERIAL INFORMATION
V Kit Content V Special T ools/Equipment V Parts to Modify Spares
V Consumables V Disposition of Existing Parts V Other
3. ACCOMPLISHMENT INSTRUCTIONS
V J o b S e t --- U p V Procedure V Close- - -Out V Te s t
V Illustration(s) V Other
4. COMMENTS, REMARKS, SUGGESTIONS
Email PDF to:
george.moffatt@dehavilland.com

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
