# Bombardier Service Bulletin 84-57-09

Copy: Service Bulletin 84-57-09 ("Service Bulletin 84-57-09"), 62 pages: PDF https://openairdocs.org/files/sha256/73/91/73911f0b48d03e6847e7aae058867ade59251bf5caba91b78f31542f7a19e54c; text https://openairdocs.org/service-documents/bombardier/sb-84-57-09/file/73911f0b48d0.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2011-0036; AD 2011-13-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 84-57-09
- Latest revision known: 84-57-09, Revision B, dated September 3, 2008 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-84-57-09

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-13-06](https://openairdocs.org/ad/2011-13-06.md), effective Aug 1, 2011: Revisions A and B

## Text (62 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2011-0036; AD 2011-13-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

DHC-8 (DASH 8)
SERVICE BULLETIN 84-57-09
Fuel - Fuel Tank System Design Left and Right Side (SFAR 88) Retrofit
- ModSum 4-126330
This page transmits Revision 'B' of Service Bulletin 84-57-09, pages 1 thru
58 dated 03 Sep 2008.
This service bulletin is re- issued in its entirety for the reasons that follow:
- the References section is revised to convey the latest revision of this service
bulletin and related engineering
- the MATERIAL INFORMATION section is revised as follows:
corrected the part number of a doubler, was 82811034-105, now
82822034-105
the part number of the Alodine 1132 is also revised, was 236049,
now 592939
- the Procedure part of the ACCOMPLISHMENT INSTRUCTIONS section is
revised as follows:
added new instruction (c) to existing step (20). The new instruction
removes and discard an existing bonding jumper and related
hardware
- existing step (2) in the Close Out section is revised to add new 'NOTE 1' and
rename an existing NOTE to 'NOTE 2'.
The Compliance recommendation in the previous issue of this service
bulletin is not affected by this revision. No additional rework to the aircraft is
introduced by this revision.
Remove revision 'A' of Service Bulletin 84-57-09 dated 19 Mar 2007 and
replace with attached.
Previous issues of Service Bulletin 84-57-09:
Initial issue - Pages 1 thru 58 dated 27 Jun 2006
Revision 'A' - Pages 1 thru 58 dated 19 Mar 2007
Revision 'B' 03 Sep 2008

### Page 2 (OCR)

de HAVILLAND
BOMBARDIER  DASIT8
SERVICE BULLETIN
Customer.
Support
ATA SYSTEM: 5700  NUMBER: 84-57-09
BOMBARDIER AEROSPACE REGIONAL AIRCRAFT CONSIDER THIS
SERVICE BULLETIN TO BE PARTICULARLY SIGNIFICANT AND
URGES OPERATORS TO PROMPTLY EVALUATE THE CONTENTS
SUBJECT: Fuel - Fuel Tank System Design Left and Right Side (SFAR 88)
Retrofit - ModSum 4-126330
1. PLANNING INFORMATION
A. Effectivity
Aircraft Affected:
In-Service:  DHC-8 Aircraft Models 401 and 402 Serial Numbers 4003,
4004, 4006 and 4008 thru 4118.
Verification:  ModSum 4-126330 has been installed on DHC-8 Aircraft
Model 402 Serial Number 4006.
NOTE: The instructions in this Service Bulletin are only applicable to the systems
and parts installed at the time of delivery on the aircraft or as changed by
Bombardier Aerospace Service Bulletin(s). Before you do this bulletin,
examine all STC or equivalent action changes to make sure this bulletin
can be completed.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 1 of 58  ELS

### Page 3 (OCR)

SERVICE BULLETIN 84-57-09
Spares Affected:
The following is a list of spares affected by this change. Review spares and
procurement systems to determine the existence of any listed parts. See
Paragraph 2.D., Existing Parts Accountability, for disposition.
B. Reason
Problem: This service bulletin (ModSum 4- 126330) is issued as a result of FAA
certification requirements conveyed by Special Federal Aviation
Regulation 88 (SFAR 88). The regulations are set to enhance fuel tank
system safety.
Certain fittings, couplings, o-rings, gaskets, fuel adapters and other
related components in the fuel tanks may not comply with FAA
certification requirements given in the SFAR 88 regulations (Special
Federal Aviation Regulation). The regulations are set to enhance fuel
tank system safety.
Solution: This service bulletin conveys ModSum 4-126330.
The ModSum replaces existing fittings, couplings, o-rings, gaskets,
fuel adapters and other related components in the fuel tanks with
redesigned fittings, couplings and adaptors that comply with SFAR 88
requirements. ModSum 4-126330 is designed to enhance fuel tank
system safety.
C. Description
The procedures in this service bulletin give the instructions to do the tasks that
tollow:
- lock pins are installed thru each main gear and main gear door mechanism
- the nose gear ground lock is engaged
- the aircraft is pressure defueled
- all aircraft electrical power is selected to the OFF position
- electrically grounded work platforms or ladders are set-up around and/or under
the left (and/or right) wing
- affected left and/or right side fuel tank access panels are removed
- assorted fittings, couplings, o-rings, gaskets, tuel adapters and other related
components in the fuel tanks (left and right side) are removed and replaced
- the protective finish is removed from certain areas of affected structure and
brackets. The reworked areas are treated with Alodine 1132
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 2 of 58  LS

### Page 4 (OCR)

SERVICE BULLETIN 84-57-09
- a bonding test of the reworked areas is done
- some parts are fillet profile sealed
- some fasteners are dome sealed
- an operational test of the Fuel System is done
- close-out
D.  Compliance
Bombardier Inc. highly recommends that ModSum 4-126330 be incorporated at
the earliest opportunity unless otherwise directed by the operator's airworthiness
authority.
An Airworthiness Directive from Transport Canada is pending.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of the Transport Canada Civil Aviation (TCCA) Design Approval
Organization No: DAO #93-Q-02.
Manpower
It will take an estimated 151.5 man-hours to complete this Service Bulletin. The
breakdown of the man-hours is shown in the table that follows:
TASK  MAN-HOURS
Job Set-Up  15.00
Procedure  120.00
Test / RTS  1.50
Close-Out  15.00
All costs to incorporate this ModSum are the responsibility of the Operator
Many man-hours would be saved if Service Bulletins 84-28-03 (MS 4- 126370),
84-28-04 (MS 4-126366) and 84-28-05 (MS 4-901425) are accomplished at
the same time. Common access to affected rework areas is required.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 3 of 58  ILS

### Page 5 (OCR)

SERVICE BULLETIN 84-57-09
G. Material - Price and Availability
ModKit 8MK4316-001 is available through the Customer Accounts Service Team
at Bombardier Aerospace Regional Aircraft division. Operators should submit a
purchase order specifying aircraft serial numbers) to:
Bombardier Aerospace
Customer Accounts Services Team (Mail Stop N11-32)
123 Garratt Blvd.
Toronto
Ontario
Canada M3K- 1Y5
Facsimile: (416) 375-3060
Telephone: (416) 375-3920
Kit Number  Description  Price (US$)  Delivery
8MK4316-001  Mod Kit - Fuel System  Quoted at  Will be given
- SFAR 88 Q400  time of order  at time of
order
H. Tooling - Price and Availability
None
I. Weight and Balance
None
J. Electrical Load Data
Not affected
K. Publications Affected
Maintenance Manual........  ..... PSM 1-84-2
Dash 8 Illustrated Parts Catalogue ..  ...... PSM 1-84-4
ModSums Manual ..........  ...... PSM 1-84-12
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 4 of 58  ILS

### Page 6 (OCR)

SERVICE BULLETIN 84-57-09
References
Revision 'B' of this service bulletin was prepared to the engineering drawings and
related data that follows:
DRAWING  SHEET  REV
8MK4316  1  C
824483  1  D
824483  2
8Z4483
8Z4483  4
8Z4483  5  B
8Z4469  1  B
8Z4469  2  A
8Z4469  3
ModSum 4Q126330 Rev. 'D'
ModSum 4- 126330 Rev. 'E'
PCA 40933 issue 1 (for internal reference only)
Transport Canada Airworthiness Directive Pending
2. MATERIAL INFORMATION
A. Parts Required Per Aircraft
(1) Modification Kit 8MK4316-001
(2) Detailed Kit Content:
Quantity Per Kit  Part Number  Description  Remarks
- 001
2  NAS1149D1216H  Washer
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 5 of 58  I LS

### Page 7 (OCR)

SERVICE BULLETIN 84-57-09
Quantity Per Kit  Part Number  Description  Remarks
- 001
2  MS35338-51  Lock Washer
2  AN924-8D  Nut
A/R  MS20995C32  Lock Wire
4  MS29513-227  O-Ring
14  MS29513-224  O-Ring
34  MS29513-218  O-Ring
76  MS29513-214  O-Ring
2  MS29513-149  O-Ring
40  MS29513-117  O-Ring
2  MS29513-032  O-Ring
4  MS29513-020  O-Ring
4  MS29513-017  O-Ring
2  MS29513-014  O-Ring
2  MS29513-013  O-Ring
2  MS29512-12  O-Ring
1  MS29512-10  O-Ring
4  MS29512-08  O-Ring
2  MS29512-06  O-Ring
5  MS29512-04  O-Ring
7  B0305080A28  Coupling
17  B0305080A20  Coupling
36  B0305080A16  Coupling
22  B0305080A12  Coupling
4  AS3209-117  O-Ring
2  82822298-105  Elbow
2  82822256-101  Gasket
2  82822128-107  Fuel Adapter
2  82822105-103  Adapter
2  82822077-005  Shroud
1  82822076-105  Cap
4  82822075-007  Fitting Cap
2  82822074-009  Fitting Assembly
1  82822053-105  Manifold
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 6 of 58  LS

### Page 8 (OCR)

SERVICE BULLETIN 84-57-09
Quantity Per Kit  Part Number  Description  Remarks
- 001
2  82822034-105  Doubler
2  82822032-101  Gasket
2  82822028-105  Fitting
2  82822027 - 107  Fitting
4  82820158-101  Gasket
4  72820141-103  Shroud
1  8Z4483  Retrofit Coupling  dwg only
1  8Z4469  Retrofit Fitting  dwg only
In addition to the above parts), the following material(s) are required for the
completion of this service bulletin and may be procured as single items from
Bombardier Aerospace Regional Aircraft or purchased directly from industry
sources.
Addresses of manufacturers and suppliers not shown below are listed in
either Maintenance Manual Chapter 20 or in Structural Repair Manual Chapter
51 or, for 400 Series Aircraft, in Consumable Products Manual PSM
1-84-18.
Part Number  Qty. Per Aircraft  Description  Remarks
592939  1 Tube  Alodine 1132  Touch -N Prep Pen
DHMS S3.01  2 Cartridges  Sealant  Temperature-Re-
sistant Integral
Fuel- Tanks,
DHMS A6.09-2  2 Cartridges  Sealant  High Temperature
Epoxy Adhesive,
04-14  AR  Petroleum Jelly ¾
Petrolatum
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 7 of 58  LS

### Page 9 (OCR)

SERVICE BULLETIN 84-57-09
Alodine 1132 (Touch-N Prep Pen) is available from:
Henkel Surface Technologies
32100 Stephenson Highway
Madison Heights, MI 48071
Telephone: 248-583-9300
Facsimile: 248-583-2976
B. Parts Required to Modify Spares
None
C. Special Tools and Equipment Required
None
D. Existing Parts Accountability
The following parts may be affected by this service bulletin. Indented parts are
components of the next higher assembly. The quantity (Qty.) column lists the
quantity that may be affected per aircraft for non-indented parts and the quantity
per next higher assembly for indented parts.
Existing  New Part
Part Number  Description  Qty.  IC  DC  Number  PNC
O-Ring  4  D  DIS  MS29513-227  Y
O-Ring  14  D  DIS  MS29513-224
O-Ring  34  D  DIS  MS29513-218
O-Ring  76  D  DIS  MS29513-214
O-Ring  2  D  DIS  MS29513-149
O-Ring  40  D  DIS  MS29513-117
O-Ring  2  D  DIS  MS29513-032
O- Ring  2  D  DIS  MS29513-020
O-Ring  4  D  DIS  MS29513-017
O- Ring  2  D  DIS  MS29513-014
O-Ring  2  D  DIS  MS29513-013
O-Ring  2  D  DIS  MS29512-12  Y
O- Ring  1  D  DIS  MS29512-10
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 8 of 58  ILS

### Page 10 (OCR)

SERVICE BULLETIN 84-57-09
Existing  New Part
Part Number  Description  Qty.  DC  Number  PNC
O-Ring  4  D  DIS  MS29512-08  Y
O-Ring  2  D  DIS  MS29512-06  Y
O-Ring  5  D  DIS  MS29512-04  Y
O-Ring  4  D  DIS  AS3209-117  Y
Gasket  2  D  DIS  82822256-101  Y
Gasket  2  D  DIS  82822032-101  Y
Gasket  4  D  DIS  82820158-101  Y
BO305025A28  Coupling  7  C  DIS  B0305080A28  S
BO305025A20  Coupling  17  C  DIS  B0305080A20  S
BO305025A16  Coupling  36  C  DIS  B0305080A16  S
BO305025A12  Coupling  22  C  DIS  B0305080A12  S
82822298-103  Elbow  2  C  DIS  82822298-105  S
82822128-105  Fuel Adapter  2  C  DIS  82822128-107  S
82822105-101  Adapter  2  C  DIS  82822105-103  S
82822077-003  Shroud  2  C  DIS  82822077-005  S
82822076-103  Cap  1  C  DIS  82822076-105  S
82822075-005  Fitting Cap  4  C  DIS  82822075-007  S
82822074-007  Fitting  2  C  DIS  82822074-009  S
Assembly
82822074-005  Fitting  2  C  IRWK  8Z4469-005  S
Assembly
82822053-103  Manifold  1  C  DIS  82822053-105  S
82822034-103  Doubler  2  C  DIS  82822034-105  S
82822028-103  Fitting  2  C  DIS  82822028-105  S
82822027-105  Fitting  2  C  DIS  82822027-107  S
72820141-101  Shroud  4  C  DIS  72820141-103  S
IC Interchangeability Code
A  Not interchangeable.
Removed Part. No direct replacement.
C  Conditionally Interchangeable. Installation of superseded part negates the
intent of this service bulletin.
D  Consumable item.
27 Jun 2006/  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 9 of 58  LS

### Page 11 (OCR)

SERVICE BULLETIN 84-57-09
DC Disposition
DIS Discard Part.
MUI Multiple Usage Item: Return to stock if serviceable.
RWK Rework existing part in accordance with this service bulletin.
RWI Rework existing part per .....
SAL Salvage. Return to operator's stores for salvage consideration.
PNC Part Number Code
N No equivalent Bombardier Inc. part number for reworked part. Indicate
on part that this service bulletin has been accomplished.
R Part number after rework.
S  Superseding part number.
Reworked part and superseding part are functionally and physically
equivalent but not identical.
Y  Existing part number and new part number are the same.
3. ACCOMPLISHMENT INSTRUCTIONS
A. Job Set-Up
The procedures that follow give the instructions to rework components in the left side
fuel tanks. The procedures to rework the components in the right side fuel tanks are
almost the same. Differences will be shown.
WARNING: OBEY ALL THE FUEL SAFETY PRECAUTIONS WHEN YOU DO WORK
ON THE FUEL SYSTEM AND/OR A FUEL SYSTEM COMPONENT. IF
YOU DO NOT YOU CAN CAUSE INJURIES TO PERSONS AND/OR
DAMAGE TO EQUIPMENT.
(1)  Make sure that lock pins are installed thru each main gear and main gear door
mechanism.
(2)  Make sure the nose gear ground lock is engaged.
(3)  Pressure defuel the aircraft (refer to TASK 12-10-28-650-802).
(4)  Make sure to de-energize the aircraft electrical system (refer to AMM TASK
24-00-00-861-802).
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 10 of 58  LS

### Page 12 (OCR)

SERVICE BULLETIN 84-57-09
(5) Set up work platforms or ladders around and/or under the left (and/or right) wing
to permit access to the fuel tanks. Make sure that the work platforms or ladders
are electrically grounded.
(6) Make sure to obey the fuel system safety precautions (refer to TASK
28-00-00-910-801).
(7)  Obey  the  electrical/electronic safety precautions (refer to TASK
24-00-00-910-801).
(8)  Obey the electrostatic discharge safety precautions (refer to TASK
24-00-00-910-802).
(9) Remove the left and/or right wing panels that follow:
ACCESS
521BT (and/or 621BT right wing)
522AT (and/or 622AT right wing)
522BT (and/or 622BT right wing)
522CT (and/or 622CT right wing)
523AT (and/or 623AT right wing)
524AT (and/or 624AT right wing)
524BT (and/or 624BT right wing)
524CT (and/or 624CT right wing)
524DT (and/or 624DT right wing)
524ET (and/or 624ET right wing)
524FT (and/or 624FT right wing)
DESIGNATION
Dry Bay Fuel Access Panels
Wet Bay Fuel Access Panels
Wet Bay Fuel Access Panels
Wet Bay Fuel Access Panels
Wet Bay Fuel Access Panels
Outer Wing Fuel Access Panels
Outer Wing Fuel Access Panels
Outer Wing Fuel Access Panels
Outer Wing Fuel Access Panels
Outer Wing Fuel Access Panels
Outer Wing Fuel Access Panels
(a)  For removal of the dry bay fuel access panel 521BT (and/or 621BT right
wing) refer to PSM 1-84-2 TASK 57-11-06-000-802.
CAUTION:  DRAIN THE FUEL TANK BEFORE YOU REMOVE THE ACCESS
PANELS. IF YOU DO NOT DO THIS, YOU CAN CAUSE DAMAGE TO
THE WING STRUCTURE.
(b)  For removal of the wet bay fuel access panel refer to PSM 1-84-2 TASK
57-11-01-000-801.
(c)  For remove the outer wing fuel access panels refer to PSM 1-84-2 TASK
57-21-01-000-801.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 11 of 58  LS

### Page 13 (OCR)

SERVICE BULLETIN 84-57-09
(10) Prepare the left and/or right wing fuel tanks for access (refer to TASK
28-10-00-840-801).
(11) Remove the access panels from the left nacelle that follow (refer to TASK
06-41 - 00-992-806 for component location):
ACCESS  DESIGNATION
412ET  Panel
413DL  Panel
412DT  Panel
(12) Remove the left wing leading edges that follow: (refer to applicable instructions
in TASK 57-23-01-000-801).
ACCESS  DESIGNATION
512AL  Outer Wing Leading Edge
(13) Remove the access fairing and panels from the right and left nacelle that follow
(refer to TASK 06-41-00-992-807 for component location):
ACCESS  DESIGNATION
422CT  Fairing
422DT  Panel
422ET  Panel
(14) Remove the access panel from the right nacelle that follow (refer to TASK
06-41-00-992-802).
ACCESS  DESIGNATION
262NR  Panel
(15) Remove  the  right  wing  leading  edge  that follows: (refer to TASK
57-13-01-000-801).
ACCESS  DESIGNATION
611AR  Wing Leading Edge
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 12 of 58  I LS

### Page 14 (OCR)

SERVICE BULLETIN 84-57-09
(16) Remove the left and right wing closure panels that follow:
ACCESS  DESIGNATION
531AB  Left Wing
631AB  Right Wing
B. Procedure
(1) Locate and remove the parts that follow:
(refer to Figure 2 DETAIL B, Figure 3 and applicable instructions in PSM
1-84-2 TASKS 28-23-01-000-801 and 28-23-01-000-802). Keep all
hardware for installation.
- actuator 2950004-201
- transfer valve 2960044-101
- adaptor tee W952D5C20/28 (or 82822008-953 or 82822008-959)
(a) If equipped with adaptor tee W952D5C20/28 refer to step (b). If equipped
with adaptor tee 82822008-953 or 82822008-959 do the procedure that
follows:
Remove fay sealant and protective finish from surface of the affected
adaptor tee that makes contact with the rib 85713321 to agree with
the instructions given in the SRM PSM 1-84-3 TASK
51-26-10-150-801 - Cleaning, Masking and Paint Stripping
Procedure.
Apply a layer of alodine 1132 to reworked area on applicable adaptor
tee (refer to NOTE 6 on Figure 1).
Using an indelible marker re-identify reworked adaptor tee
82822008-953 as 8Z4469-001
or adaptor tee
32822008-959 as 8Z4469-003.
(b) Wrap the actuator, transfer valve and adapter tee in a protective covers.
(c) At four locations remove and discard existing couplings and o-rings (refer
to Figure 3).
(d) Put a cap on the open ends of each related tube assemblies.
(e) Remove protective finish from rib 85713321 to agree with the instructions
given in the SRM PSM 1-84-3 TASK 51-26-10-150-801 (Cleaning,
Masking and Paint Stripping Procedure). The rework areas on the rib are
indicated with hash marks shown on Figure 4 DETAIL C-C and D-D
Apply a layer of alodine 1132 to rework area on the rib (refer to NOTE 6 on
Figure 1).
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 13 of 58  LS

### Page 15 (OCR)

SERVICE BULLETIN 84-57-09
Install the parts that follow to agree with all of the Notes and detail views given
on Figure 2 DETAIL B, Figure 3 and applicable instructions in PSM 1-84-2
TASKS 28-23-01-400-801 and 28-23-01-400-802.
- actuator 92003SOCN2950004-201
- transfer valve 92003-2960044-101
- adaptor tee W952D5C20/28 or 824469-001 or 8Z4469-003
- new o-rings MS29513-149 and MS29513-032
- new couplings B0305080A20 and related o-rings MS29513-218 (at four
locations).
(a) Make sure to fillet profile seal at actuator and adapter tee with DHMS S3.01
(see Note 3 on Figure 3).
(b) Do an electrical bonding test of the actuator, transfer valve and adaptor tee
to the aircraft structure. Readings to be less than 20 milliohms (refer to
PSM 1-84-2 TASK 51-80-00-760-801).
(c) Dome seal the fasteners with DHMS S3.01 (see Note 4 on Figure 3) to
agree with instructions given in the SRM PSM 1-84-3 TASK
51-23-00-800-801.
(3)  Rework front spar at Y180.931 and Y179.424 as follows:
(refer to Figure 2 and 5 detail E-E and Figure 6 detail F-F and applicable
instruction in PSM 1-84-2 TASK 28-21-06-000-801.
NOTE: Access to the front spar rework area thru the right side nacelle is more
difficult than access to the front spar thru the left side nacelle. Additional
access is gained if some of the disassembly and rework is accomplished
working from the exhaust section in the right side nacelle.
(a) Loosen the clamps that secure shroud DEH2024-0103.
(b) Disconnect each end of the shroud drain line. Move the shroud out of the
way to gain access to affected components and front spar.
(c) Disconnect the forward end of the fuel feed line and the motive flow line in
the nacelle. Put a cap on each line. Loosen related block clamps that
secure the motive flow and fuel feed line. Move the lines in the forward
direction as required to gain addition work space at the front spar.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 14 of 58  LS

### Page 16 (OCR)

SERVICE BULLETIN 84-57-09
(d) Locate and remove the parts that follow:
- adapter 82822128-105 (discard)
- fitting 82822027-105 (discard)
- fitting 82822028-103 (discard)
- couplings B0305025A16C and B0305025A12 (discard)
(e) Put a cap on the open ends of each related tube assembly.
In the fuel tank find and identify the part number of the doubler (refer to
Figure 6 for doubler location). If the part number is 82822034 - 103 remove
and discard it. If the part number is 82822034-105 do not remove it.
CAUTION:  DO NOT DAMAGE SHROUD DEH2024-0103 WHEN REWORKING THE
FRONT SPAR.
(g) Remove protective finish from affected area on front spar 85713502 to
agree with the instructions given in the SRM PSM 1-84-3 TASK
51-26-10-150-801. The rework area on the front spar is indicated with
hash marks shown on Figure 7 VIEW T.
Apply a layer of alodine 1132 to rework area on p/n 85713502 (front spar)
(refer to NOTE 6 on Figure 1).
Re-install the parts removed in step (3) and new replacement parts that follow.
Installation must agree with all of the Notes and detail views given on Figure 5
detail E-E, Figure 6 detail F-F and applicable instructions in PSM 1-84-2
TASK 28-21-06-400-801.
- doubler 82822034-105 (if 82822034-103 was discarded)
- fuel adapter 82822128-107
- fitting 82822027-107 and related o-ring
- fitting 82822028-105 and related o-ring
- couplings B0305080A12 and B0305080A16 and related o-rings
(a) Apply a layer of DHMS A6.09-2 epoxy sealant to the forward side of new
doubler 82822034-105. Set doubler in position on the aft side of the front
spar.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 15 of 58  ILS

### Page 17 (OCR)

SERVICE BULLETIN 84-57-09
Alternate tightening when installing new fitting 82822027-107 and
82822028-105 (see Note 7 on Figure 1 and 6). Secure the fittings to each
other using lock wire MS20995C32. Apply sealant DHMS S3.01 on the
ends of the lock wire.
(c) Do an electrical bonding test of fitting 82822027-107 and fitting
82822028-105 to the aircraft structure. Readings to be less than 20
milliohms (refer to PSM 1-84-2 TASK 51-80-00-760-801).
(d) Reinstall the fuel feed line and the motive flow line in original position using
kept block clamps.
Make sure that the shroud DEH2024-0103 is in situ on the lines and
pushed as far forward towards the firewall as possible. Also do not
secure the related drain line to the shroud at this time. The shroud
and drain line will be secured in original position after a pressure test
of the affected system. The pressure test is given in the close-out
section of this service bulletin.
(e) Reconnect each end of the shroud drain line.
(5)  Locate and remove the parts that follow:
(refer to Figure 2 View G-G and Figure 8 VIEW H-H and applicable instructions
in PSM 1-84-2 TASK 28-12-11-000-801).  Keep all hardware for
installation.
- elbow 82822298-103 (discard)
- gasket 82822256-101 (discard)
- coupling B0305025A16 (discard)
(a) Remove protective finish from the rib 85713831 to agree with the
instructions given in SRM PSM 1-84-3 TASK 51-26-10-150-801. The
rework areas on the rib are indicated with hash marks shown on Figure 8
VIEW V- V.
(b) Apply a layer of alodine 1132 to rework area on the rib (refer to NOTE 6 on
Figure 1).
Install replacement part that follow to agree with all of the Notes and detail views
given  Figure  8 and applicable instruction given in  TASK
28-12-11-400-801.
- gasket 82822256-101
- elbow 82822298-105
- coupling B0305080A16 and related o-rings MS29513-214
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 16 of 58  ILS

### Page 18 (OCR)

SERVICE BULLETIN 84-57-09
(a) Do an electrical bonding test at elbow 82822298-105 to the aircraft
structure. Reading to be less than 20 milliohms (refer to PSM 1-84-2
TASK 51-80-00-760-801).
(b)  Make sure to fillet profile seal bolts NAS6203-5, washers AN960D10L and
nuts MS21042-3 (see Note 3 on Figure 8) with DHMS S3.01 to agree with
applicable instructions in SRM PSM 1-84-3 TASK 51-23-00-800-801).
Locate and remove the parts that follow (refer to Figure 2 View J-J and Figure 9
and Figure 10 SECTION L-L and applicable instructions in PSM 1-84-2 TASK
28-21-36-000-801).
- fitting 82822075-005 (discard)
- gasket 82820158-101 (discard)
- shroud 72820141 - 101 (discard)
- o-rings MS29512-04, MS29513-017, MS29513-214 and MS29513-227
(discard all used o-rings)
(a) Remove protective finish from the mating area on the aft side of the rear
spar to agree with the instructions given in the SRM PSM 1-84-3 TASK
51-26-10-150-801. The rework area is indicated with hash marks on
view of spar refer to Figure 10 VIEW R-R.
(b) Apply a layer of alodine 1132 to rework area on the spar (refer to NOTE 6
on Figure 1).
(8)  Install replacement part that follow to agree with all of the Notes and detail views
given on Figure 10 SECTION view L-L and applicable instruction given in TASK
28-21-36-400-801.
- fitting 82822075-007
- gasket 82820158-101
- shroud 72820141-103
- o-ring's MS29512-04, MS29513-017, MS29513-214, and MS29513-227
(a) Make sure to torque tighten the pressure switch to 120 to 150 in-Ibs.
Install lockwire from pressure switch to one of three adjacent bolts (refer to
PSM 1-84-2 TASK 20-10-30-400-801).
(b) Do an electrical bonding test of fitting 82822075-007 to the aircraft
structure. Reading to be less than 20 milliohms (refer to PSM 1-84-2
TASK 51-80-00-760-801).
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 17 of 58  LS

### Page 19 (OCR)

SERVICE BULLETIN 84-57-09
(c) Make sure to fillet profile seal between the outer shroud and aft face of rear
spar in location depicted (for location see Note 3 on Figure 10 SECTION
L-L) using DHMS S3.01 sealant to agree with applicable instructions in
SRM PSM 1-84-3 TASK 51-23-00-800-801.
(9)  Remove the parts that follow to agree with all of the Notes and detail views given
on Figure 9 and Figure 11 SECTION K-K and applicable instructions in PSM
1-84-2 TASK 28-23-11-000-801. Keep all hardware for installation.
NOTE: Some earlier aircraft are equipped with fitting 82822074-005 instead of
the fitting 82822074-007. If that is the case do not discard the related
shroud 82822077-003 or the fitting -005. The fitting requires rework
and will be re-installed with the original shroud 82822077-003.
- shroud 82822077-003 (refer to above Note)
- fitting 82822074-007 (discard) or fitting 82822074-005 (do not discard)
- gasket 82822032-101 (discard)
- o-rings MS29512-08, MS29513-013, MS29513-014 and MS29513-020
(discard)
(a) For aircraft equipped with fittings 82822074-007 discard the shroud
82822077-003 and refer to step (b).
For earlier aircraft equipped with fittings 82822074-005 do the procedures
that follow:
1  Remove protective finish from fitting 82822074-005 at location
shown (excluding the O-ring grooves) (refer to Figure 11 Sheet 1
DETAIL AA).
2  Apply a layer of alodine 1132 to rework area on the fitting (refer to
NOTE 6 on Figure 1).
Re-identify fitting 82822074-005 as 8Z4469-005 using an indelible
marker.
4  Fabricate a new gasket 8Z4469-101 as shown on Figure 11 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 18 of 58  LS

### Page 20 (OCR)

SERVICE BULLETIN 84-57-09
5  Examine the shroud 82822077-003 to make sure that the internal
surface is clean. If not, clean as required then continue with step
below.
Remove protective finish from the mating area on the aft side of the rear
spar to agree with the instructions given in the SRM PSM 1-84-3 TASK
51-26-10-150-801. The rework area is indicated with hash marks on
the aft side of the rear spar shown on Figure 11 VIEW P-P.
(c) Apply a layer of alodine 1132 to rework area on the spar (refer to NOTE 6
on Figure 1).
(10) Install replacement parts that follow to agree with all of the Notes and detail
views given on Figure 11 SECTION view K-K and applicable instruction given in
TASK 28-23-11-400-801.
For earlier aircraft originally equipped with fitting 82822074-005, re-install
same part numbers fitting 82822074-005, shroud 82822077-003 and new
gasket 824469-101.
- gasket 82822032-101 (or 8Z4469-101_earlier aircraft)
- fitting 82822074-009 (or 82822074-005 earlier aircraft)
- shroud 82822077-005 (or 82822077-003 earlier aircraft)
- o-rings MS29512-08, MS29513-013, MS29513-014 and MS29513-020.
(a) Torque tighten the pressure switch to 120 to 150 in -Ibs. Install lockwire
from pressure switch to one of three adjacent bolts (refer to PSM 1-84-2
TASK 20-10-30-400-801).
(b)  Do an electrical bonding test of fitting 82822074-009 or reworked fitting
824469-005 to aircraft structure. Reading to be less than 20 milliohms
(refer to PSM 1-84-2 TASK 51-80-00-760-801).
(c)  Install lockwire from the solenoid valve to one of four adjacent bolts (for
location see Note 10 on Figure 1 and 11).
Make sure to fillet profile seal the fitting assembly 82822074-009 or
reworked fitting 8Z4469-005 and aft face of rear spar in location depicted
(see Note 3 on Figure 11 SECTION view P-P) using DHMS S3.01 sealant
to agree with applicable instructions in SRM PSM 1-84-3 TASK
51-23-00-800-801.
(11) Remove and discard existing manifold 82822053-103 (left side only) and
o-ring MS39512-10 (refer to Figure 2 and 12, DETAIL M and applicable
instructions given in PSM 1-84-2 TASK 28-11-06-000-801). Keep all
hardware for installation.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 19 of 58  LS

### Page 21 (OCR)

SERVICE BULLETIN 84-57-09
(a) Install protective caps on all open lines and equipment to prevent
contamination to the fuel system.
(b) Remove protective finish from the mating surface area to agree with the
instructions given in the SRM PSM 1-84-3 TASK 51-26-10-150-801.
The rework area is indicated with hash marks shown on Figure 12 VIEW
(c) Apply a layer of alodine 1132 to rework area (refer to NOTE 6 on Figure 1).
(12) Install new manifold 82822053-105 and o-ring MS29512-010 to agree with all
of the Notes and detail views given on Figure 12 and applicable instructions in
PSM 1-84-2 TASK 28-11-06-400-801.
(a) Make sure that the inscription " HINGE" on the check valve is facing up
when installed.
(b) Do an electrical bonding test of the manifold 82822053-105 to aircraft
structure. Reading to be less than 20 milliohms (refer to PSM 1-84-2
TASK 51-80-00-760-801).
(13) Remove and discard adapter 82822105-101 and o-ring MS29512-06 (refer to
Figure 2 and Figure 13 DETAIL N and applicable instructions in PSM 1-84-2
TASK 28-11-06-000-801).
(a) Remove protective finish from the mating surface area to agree with the
instructions given in the SRM PSM 1-84-3 TASK 51-26-10-150-801.
The rework area is indicated with hash marks shown on Figure 13 VIEW
(b) Apply a layer of alodine 1132 to rework area (refer to NOTE 6 on Figure 1).
(14) Install new adapter 82822105-103 and o-ring MS29512-06 to agree with all of
the Notes and detail views given on Figure 13 DETAIL N and applicable
instructions in PSM 1-84-2 TASK 28-11-06-400-801.
(a) Do an electrical bonding test of adapter 82822105-103 to aircraft
structure. Reading to be less than 20 milliohms (refer to PSM 1-84-2
TASK 51-80-00-760-801).
(b) Make sure to fillet profile seal the fitting Installation in location depicted
(see Note 3 on Figure 13 DETAIL N) using DHMS S3.01 sealant to agree
with applicable instructions in SRM PSM 1-84-3 TASK
51-23-00-800-801.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 20 of 58  ILS

### Page 22 (OCR)

SERVICE BULLETIN 84-57-09
(15) Dome seal the fasteners (on the dry side) installed thru the angle attachment
and front spar to agree with the detail views and Notes given on Figure 14. Use
DHMS S3.01 sealant and refer to the procedures given in SRM PSM 1-84-3
TASK 51-23-20-390-801.
IMPORTANT NOTICES FOR STEPS (16) THRU (20)
QUANTITY AND LOCATION OF  B0305025A
COUPLINGS ON SOME AIRCRAFT MAY NOT MATCH
SOME OF THE VIEWS AND RELATED TEXT FOR
FIGURES 16 THRU 23.
ALL B0305025A COUPLINGS MUST BE REPLACED
BY B0305080A COUPLINGS.
COUPLING ARE NOT  IF THE SLEEVE AND 0-RINGS OF A B0305025A  DISTURBE CLAM SHELL ONLY  IT IS
ACCEPTABLE  TO REPLACE THE
WITHOUT  REPLACING  THE SLEEVE AND THE
O-RINGS
(16) Rework the scavenge and motive flow lines as follows:
(a) At five locations remove and discard existing couplings B0305025A12 and
related o-rings from the scavenge and motive flow lines (refer to Figure 16
DETAIL A).
(b) At five locations install new couplings B0305080A12 and related o-rings
MS29513-117 to the scavenge and motive flow lines (refer to Figure 16).
At two locations remove and discard two existing bonding jumpers
CSP476-7BB6 and related hardware (refer to Figure 17).
(17) Rework the engine feed system as follows:
NOTE: Left side fuel tank rework is shown on Figure 18 Sheets 1 and 2.
Right side rework is shown on Figure 19 Sheets 1 and 2.
At ten locations (left and/or right side tanks) remove and discard existing
couplings B0305025A16 and related o-rings from the engine feed lines to
agree with the views shown on Figure 18 Sheet 1 and Sheet 2 (or Figure
19 Sheet 1 and Sheet 2).
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 21 of 58  ILS

### Page 23 (OCR)

SERVICE BULLETIN 84-57-09
(b) Install new couplings B0305080A16 and o-rings MS29513-214.
(18) Rework the refuel/defuel system as follows:
NOTE: Left side fuel tank rework shown on Figure 20 Sheets 1 and 2. Right
side fuel tank rework shown on Figure 21.
Remove and discard existing couplings B0305025A16, B0305025A20 and
B0305025A28 and related o-rings from the refuel/defuel lines to agree the
views shown on Figure 20 Sheet 1, Sheet 2, Figure 21 and applicable
instructions given in PSM 1-84-2 TASKS 28-23-01-000-801,
28-23-06-000-801.
Install new couplings B0305080A16, B0305080A20, B0305080A28 and
o-rings MS29513-214, MS29513-218 and MS29513-224 to agree with
the views shown on Figure 20 Sheet 1, Sheet 2, Figure 21 and applicable
instructions given in PSM 1-84-2 TASKS 28-23-01-400-801,
28-23-06-400-801.
Remove and discard existing CAP 82822076-103 and related o-ring (left
wing fuel tank only). Install a new CAP 82822076-105 and o-ring
MS29512-04 (refer to Figure 20 Sheet 1).
(19) Rework the outer wing Scavenge Flow Lines and the Outboard Vent Line as
follows:
Remove and discard existing couplings B0305025A12, B0305025A16 and
related o-rings to agree with applicable instructions given in PSM
1-84-2 TASK 28-12-06-000-801, 28-11-16-000-801 and the
detail views shown on Figure 22.
Install new couplings B0305080A12, B0305080A16 and o-rings
MS29513-117 and MS29513-214 to agree with applicable instructions
given in PSM 1-84-2 TASK 28-12-06-400-801, 28-11-16-400-801
and the detail views shown on Figure 22.
Remove and discard existing bonding jumpers CSP476-7BB5, clamps
AN735D16, AN735D12 and related hardware (refer to detail views shown
on Figure 22).
(20) Rework the Inboard Vent Line as follows;
(a) Remove and discard existing couplings B0305025A16 and related o-rings
to agree with applicable instructions given in PSM 1-84-2 TASK
28-12-01-000-801 and the detail views shown on Figure 23 Sheet 1.
Install new couplings B0305080A16 and o-rings MS29513-214 to agree
with applicable instructions given in PSM 1-84-2 TASK
28-12-01-400-801 and the detail views shown on Figure 23 Sheet 1.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 22 of 58  LS

### Page 24 (OCR)

SERVICE BULLETIN 84-57-09
(c) Remove and discard existing bonding jumper CSP476-7BB10 and related
hardware (refer to view shown on Figure 23 Sheet 1).
(d) Remove and keep the screw NAS1801-3-11 and related washer
AN960D10L that attaches tube assembly 82822095 to bracket 85714404
(refer to locator view F-F on Figure 23 Sheet 1 and detail VIEW F-F on
sheet 2). Remove existing protective finish from the surface of bracket
85714401 which interfaces with bracket 85714435.
(e) Dampen a clean white lint-free cloth with solvent. Wipe clean the bared
metal surface of bracket 85714404. Make sure that all traces of unwanted
material are removed and the surface is clean.
(f) Apply alodine 1132 on the bared metal of the bracket as follows:
Apply "Touch-N Prep" alodine 1132 to prepared surface using
smooth even strokes. Make sure to cover all edges.
For best results the initial coat should be applied in one direction
using a 50% overlap on each pass. Allow the first coat to dry then
apply a second coat at right angles to first coat with a 50% overlap.
Do not allow the alodine to puddle or improper drying could occur.
4 Allow the alodine to dry. Forced warm air will speed drying (130 deg
F / 54 deg C maximum temperature).
5 Do not rinse the treated area.
(g) Re-assemble tube assembly 82822095 to bracket 85714401 using kept
hardware.
(h)  Dome seal the screw NAS1801-3-11 and related washer with DHMS
S3.01 class B type I or type Il to agree with the procedure given in PSM
1-84-3 Task 51-23-00-800-801.
Dome seal the anchor nut (located on the back side of bracket 85714404)
with DHMS S3.01 class B type I or type Il to agree with the procedure given
in PSM 1-84-3 Task 51-23-00-800-801.
Fillet seal around the interface of bracket 85714404 and tube 82822095
with DHMS S3.01 class B type I or type Il to agree with the procedure given
in PSM 1-84-3 Task 51-23-00-800-801.
(21) Repeat the applicable instructions in the Job Set-Up and Procedure section to
rework the fuel systems in the right wing.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 23 of 58  ILS

### Page 25 (OCR)

SERVICE BULLETIN 84-57-09
C. Close Out
(1) Do the return to service procedures that follow:
(a) Refuel / Defuel / Transfer system - Pressure Testing
1  Disconnect the L/H Tank Pressure Relief Servo line at the L/H Refuel
Tee Adapter (W9205C20/28) adjacent to wing sta. Y42.00 (refer to
Figure 3).
Disconnect R/H Tank Pressure Relief Valve Servo Line at Refuel /
Defuel line located near Y173.20 adjacent to rear spar (refer to Figure
3  Install pressure cap on Refuel / Defuel line P/N 82822138 at
disconnected R/H servo line.
Use appropriate adapter, and connect ground air supply to L/H Refuel
Tee Adapter.
Manually open Refuel / Transfer / Defuel S/O Valve at L/H and R/H
Tanks.
CAUTION:  MAKE SURE TO MONITOR THE AIR PRESSURE WHILE IT IS
CONNECTED TO THE FUEL SYSTEM. DO NOT EXCEED 50 +/- 5
PSIG.
Adjust and maintain air pressure at 50 +/- 5 psig.
Check for leaks at connections/fittings that have been replaced, or
disturbed, up to L/H and R/H Level Control Valve, located adjacent to
Y79.70.
At completion of test reconnect L/H and R/H Pressure Relief Valve
Servo Line.
(b) Engine and APU Feed Line - Testing
1  Disconnect engine feed flexible hose at airframe system/engine
interface.
Disconnect and plug APU fuel feed line at APU.
Use appropriate adaptor and connect ground air supply to Engine
Feed Line.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 24 of 58  I LS

### Page 26 (OCR)

SERVICE BULLETIN 84-57-09
4  Ensure the Engine Feed S/O Valve is open.
Manually open the APU Feed S/O Valve.
CAUTION:  MAKE SURE TO MONITOR THE AIR PRESSURE WHILE IT IS
CONNECTED TO THE FUEL SYSTEM. DO NOT EXCEED 50 +/- 5
PSIG.
6 Adjust and maintain air pressure at 50 +/- 5 psig.
7 Check for leak at connections/fittings that have been replaced. (Note:
There will be minor leak across the Main ejector check valve.)
8  At completion of test, reconnect flexible hose at engine interface, and
APU.
9 Check for leak at flexible hose/engine interface after engine run.
(c) Motive Flow Pressure Line - Test
Disconnect Motive Flow flexible hose at airframe system/engine
interface.
Cap Motive Flow line in tank before check valve using an
MS21913-8 cap.
Use appropriate adaptor and connect ground air supply as indicated.
CAUTION:  MAKE SURE TO MONITOR THE AIR PRESSURE WHILE IT IS
CONNECTED TO THE FUEL SYSTEM. DO NOT EXCEED 50 +/- 5
PSIG. MAKE SURE THAT THE AIR PRESSURE SUPPLY IS FILTERED
AND FREE OF OILS AND MOISTURE.
Adjust and maintain air pressure at 50 +/- 5 psig.
Check for leak at front spar connections/fittings that have been
replaced.
6  At completion of test, reconnect flexible hose at engine interface.
Secure that front spar shroud DEH2024-0103 and drain line after
completion of the pressure test (refer to Figure 6).
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 25 of 58  ILS

### Page 27 (OCR)

SERVICE BULLETIN 84-57-09
Check for leak at flexible hose/engine interface after engine run.
Check Nacelle drain line which connects to Front Spar Boot for Fuel
leakage after engine run.
(2)  Inspect all fuel system pipes within the fuel tanks to ensure that no less than
0.125 inch. clearance exists between pipes and between pipes and structure
(refer to Notes 1 and 2 below for additional information).
NOTE 1: In some aircraft there are a number of vent line installation locations
where the 0.125 inch clearance does NOT apply. These locations are
characterized by a teflon sleeve which is placed around the vent line
where the vent line passes close to structure at wing rib penetrations.
At these locations, it is acceptable for the air gap to be less than 0.125
inches and in some cases the teflon sleeve may be touching the
structure.
NOTE 2: If the 0.125 inch clearance cannot be achieved (except those
describes in NOTE 1 above), contact the Technical Help Desk in
Toronto  at telephone number (416) 375-4000 or e-mail:
thd.qseries@aero.bombardier.com.
Provide aircraft serial number, description / location of the non
compliant condition, part number of affected items and if possible
digital images. All requests for solution to be forwarded to the EMC
group for consultation.
(3)  Install all access panels that were removed to do this service bulletin.
(4)  Remove all tools and equipment and unwanted materials from the work areas.
(5)  Pressure retuel tanks with a known quantity of fuel refer to PSM 1-84-2 TASK
12-10-28-910-801 - Fuel Servicing Safety Precautions.
(6) Do a leak check at the rework locations along wing sta. Y42.00, the front and
rear spar.
Record the fuel quantity indication using the FUEL QTY indicator on the
Refuel/Defuel panel and MagnaStick then compare values to known fuel
tendered in step (4).
(8)  Do an operational test of the Fuel System refer to PSM 1-84-2 TASK
28-00-00-710-801.
(9)  On incorporation of this ModSum make an entry that conforms to local
regulatory requirements in the applicable logbooks). If only part of this
ModSum is completed, use only this service bulletin number as reference and
detail exact limit of work completed. Enter component serial numbers if
applicable. Enter this ModSum number only after complete and functional
incorporation of all work defined in this service bulletin.
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 26 of 58  LS

### Page 28 (OCR)

SERVICE BULLETIN 84-57-09
NOTES:
STRUCTURAL
REPAIR MANUAL TASK 51-23-00-800-801.
CLASS TAPEST SEALANT PER STRUCTU  PAIR MANUAL TASK 51-23-00-800-801.  SEALANT PER  STRUCTURAL
ELECTRICAL BONDING BY DIRECT CONTACT ON
TASK 51-80-00-340-801.  SIDE  PER SIRUCTURAL REPAIR MANUAL
(6 A) MASK AREA SURROUNDING HATCHED AREA
3 SAM TASK 51-26-10-150-801  ALL PROTECTIVE TREATMENT PER
) APPLY TOUCH-N-PREP COATINGS  PARKER TO HATRED AREAS AS FALLONS 113
1) REMOVE CAP.  CE RAZOR BLADE PENIT SINOLE  IF NECESSARY CUT
CONFORM
2) HO ACTIVATE. PRESS TIP AGAINST DAMN
3) DE COATED IS CLEAN AND DRY.  SURFACE TO
4) APPE TOUCE PREPARED SIPFACE LODINE
STEP 2.
WITH WARM AIR (EG
HAIR DRYER) OR DRY USING  (130°F MAXIMUM). DO NOT RINSERT LAMP
RETROFIT - FUEL SYSTEM
NOTES CONTINUED:
ON RE-INSTALLATION, ALTERNATE TIGHTENIN
BETWEEN 82822027 &  82822028
INSTALL LOCKWIRE PER PSM 1-84-2 TASK
20-10-30-400-801 - SEALANT TO BE APPLIED
TO ENDS OF LOCKWIRE USING DEMS S3.01
CLASS B TYPE 1 OR TYPE I1 SEALANT.
ELECTRICAL BONDING BY DIRECT CONTACT ON
POCKET SIDE PER SRM TASK 51-80-00-340-801.
INSTALL LOCKWIRE PER PSM 1-84-2 TASK
20-10-30-400-801  ATTACHING SOLENOID
SOLENDID VALVE TO ONE OF FOUR BOLTS.
TORQUE TIGHTEN PRESSURE SWITCH TO
120-150 IN-LBS.  INSTALL LOCKWIRE PER
ATTACHING PRESSURE SWITCH 10-ONE OF
THREE BOLTS.
ELECTRICAL BONDING BY DIRECT CONTACT ON
DRY SIDE PER STRUCTURAL REPAIR MANUAL
TASK 51-80-00-340-801.
DOME SEAL FASTENERS ON THE DRY SIDE
USING S3.01 CLASS B  TYPE I OR TYPE 11
PER SRM TASK 51-23-20-390-801.
Figure 1 Sheet 1
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 27 of 58  I LS

### Page 29 (OCR)

SERVICE BULLETIN 84-57-09
NOTES CONTINUED:
ELECTRICAL BONDING BY DIRECT CONTACT
UNDER WASHER PER STRUCTURAL REPAIR MANUAL
TASK 51-80-00-340-801.
/15\  TO ACHIEVE THE INTENT OF MS 4Q126330,
POST MS 4Q126330 PARTS MAY ONLY BE
REPLACED WITH POST MS 4Q126330 PARTS.
16\  NOT APPLICABLE
NOT APPLICABLE
PETROLEUM JELLY MAY BE APPLIED TOTHREADS TO AID INSTALLATION
ALSO IT MAY BE NECESSARY TO FLATTEN NEW LOCK WASHER MS35338-51
TO MAKE IT EASIER FOR INSTALLATION OF THE RELATED NUT AN924-8D
19 HARDWARE ITEMS SHOWN IN BRACKETS ARE
REFERENCE ONLY.  INSTALLED HARDWARE MAY
VARY FROM REFERENCE HARDWARE.  HARDWARE CURRENTLY INSTALLED ON AIRCRAFT.
20 REMOVE ONLY THE BONDING JUMPERS SPECIFIED
ON THIS DRAWING.
Figure 1 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 28 of 58  ILS

### Page 30 (OCR)

SERVICE BULLETIN 84-57-09
DETAIL A  SCALE: 1/8  LHS SHOWN,  RHS OPPOSITE
JL
DETAIL M
-173.20
DETAIL N
Figure 2 Sheet 1
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 29 of 58  LS

### Page 31 (OCR)

SERVICE BULLETIN 84-57-09
Y 101D  -407.00  DETAIL A  SCALE: 1/8  LHS SHOWN,  RHS OPPOSITE
Figure 2 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 30 of 58  LS

### Page 32 (OCR)

SERVICE BULLETIN 84-57-09
(85713321)
(82822039 TUBE) -
O-RING
MS29513-149
• T PANSFER VALVE
2960044-101
ACTUATOR
2950004-201
WAS COUPLING B0305025A20-
AND RELATED O-RING
NOW COUPLING B0305080A20
O-RINGS MS29513-218
- 3 4 PLOS  O - RING
WAS  ADAPTOR TEE  MS29513-032
W952D5C20/28
OR
82822008-953
OR
82822008-959  (82822040 TUBE)
NOW  ADAPTOR TEE
W952D5C20/28  WAS
OR  COUPLING B0305025A20
8Z4469-001
OR  LOS  AND RELATED O-RING
8Z4469-003
NOW
COUPLING B0305080A20
O-RINGS MS29513-218
WAS  COUPLING B0305025A28
AND RELATED O-RING  (MS21043-3 NUT)
(NAS6203-6 BOLT)
NOW  COUPLING B0305080A28  O-RINGS MS29513-224  DETAIL B  C  (2X AN960-10L WASHER)
(UPPER SKIN REMOVED FOR CLARITY)
LHS SHOWN RHS OPPOSITE
Figure 3
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 31 of 58  LS

### Page 33 (OCR)

SERVICE BULLETIN 84-57-09
3 TRACE)
(STOR 2 TRACE)
6 PLCS  VIEW C-C Le  VIEV LOCKING a TEND Y1020-42.00
SHOVING APFILICATION OF FROTECTIVE FINISH
(85713321)
(85713321)
Ø2.90
Ø2.75
VIEW D-D  AS OPOST
VIEW LOOKING INBOARD Y102D -42.00
HOWING APPLICATION OF PROTECTIVE FINIS
Figure 4
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 32 of 58  LS

### Page 34 (OCR)

SERVICE BULLETIN 84-57-09
E
- (85713502)
(82822002)
(Z = 179.551)
VIEw E-E
LOOKING INB'D LHS
RHS SIMILAR
SCALE 1/2
Figure 5
27 Jun 2006
Revision 'B' 03 Sep 2008  LS

### Page 35 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  (NAS1922-0100-3 CLAMP)  (NAS1922-0075-3 CLAMP)
(Y-179. 424)
(DEH2024-0103 SHROUD)  (Y-180. 931)
O-RING
AS3209-1  SERVICE BULLETIN 84-57-09
X-382.210)
- LOCK WASHER S35338 - 51 448  WASHER NAS1149D1216H
WAS COUPLING BO305025A12
NOW COUPLING BO305080A12  NUT AN924-8D
FRONT SPAR
Figure 6  WAS 82822128-105 FUEL
NOW FUEL ADAPTER
O-RING  82822128-107
MS29512-12
WAS FITTING  WAS DOUBLER 82822034 - 103
82822027-105  NOW DOUBLER 82822034-105
A 82822027-107 L  NOW FITTING  O-RING MS29512-08
WAS COUPLING BO305025A16C  NOW COUPLING B0305080A16  WAS FITTING 82822028-103  NOW FITTING 82822028-105 L
O-RING MS29513-214 (X2)  LOCK WIRE&  M920995032.
FVD
SECTION F-F
ROTATED CW 90*
Page 34 of 58  S.B. 84-57-09  HE SHYAR  INB'D

### Page 36 (OCR)

SERVICE BULLETIN 84-57-09
85713502
FRONT SPAR
1. 86
R. 93
VIEW T
SCALE: 1/4
_HS SHOWN,  RHS SIMILAR
LOOKING NORMAL TO FRONT SPAR DATUM
SHOWING APPLICATION OF PROTECTIVE FINISH
Figure 7
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 35 of 58  LS

### Page 37 (OCR)

SERVICE BULLETIN 84-57-09
(FRONT SPAR
TRACE)
RIB  ø. 7
ELBOW  85713831  VIEW V-V
SHOWING APPLICATION OF PROTECTIVE FINISH
VIEW G-G
ROTATED 90  Y1010 -407.015  (Y 101D
-407.019)
GASKET
82822256-101
(NAS6203-5 BOLT)
(MS21042-3 NUT)
(AN960D10L WASHER)  - (82822251 VENT LINE)
13 14
WAS COUPLING B0305025A16
AND RELATED O-RING
NOW COUPLING B0305080A16
WAS ELBOW 82822298 - 103  O-RING MS29513-214
NOW ELBOW 82822298-105
- (85713831)
VIEW H-H
. 500
438
Figure 8
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 36 of 58  LS

### Page 38 (OCR)

SERVICE BULLETIN 84-57-09
7X
VIEW J-J  SCALE: 1/2
Figure 9
27 Jun 2006
Revision 'B' 03 Sep 2008  LS

### Page 39 (OCR)

SERVICE BULLETIN 84-57-09
SHROUD
WAS 72820141-101
NOW 72820141 - 103  - (NAS6603H10)  (NAS43DD3-7FC)
(AN960D10L)
FITTING  (MS20995C32)
WAS 82822075-005
NOW 82822075-007  - O-RING
MS29512-04
- (92003800N17-262-1 PRESUME SWITCH) /111
O-RING
101589102828  MS29513-214
O-RING
REAR SPAR
AFT SIDE
SECTION L-L
Y1020 732.22 L & P
FLAT SIDE
$2.00
VIEW R-R
4 PLACES
SHOWING APPLICATION OF PROTECTIVE FINISH
Figure 10
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 38 of 58  LS

### Page 40 (OCR)

SERVICE BULLETIN 84-57-09
Y 100
79. 700
& PLOS  82822074-00526
G FLAT SIDE
DETAIL  _ AA
VIEW ---  SCALE  _ 1/1
1/2  THIS  VIEW  _FOR
SHOWING APPLICATION OF  PLACES  PROTECTIVE FINISH  82822074-005 ONLY
O-RING
O-RING  MS29513-020
MS29512-08
O-RING
Г MS29513-014
SOLENOID VALVE)
O- RING
(92003SOCN2960004-101  MS29513-013
SHROUD  FITTING
(EARLIER A/C) 82822077-003  (EARLIER A/C)
OR  82822074-005
82822077-005  OR
WAS 82822074-007
DETAIL AA-  /12  NOW 82822074-009
GASKET
82822032-101
SECTION K-K
Y102D 76.83 LH & RH
Figure 11 Sheet 1
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 39 of 58  I LS

### Page 41 (OCR)

SERVICE BULLETIN 84-57-09
R. 30
4 PLCS
-Ø1.063
1. 156
. 578
ø .25
4 PLCS
. 578-
1.156
8Z4469-101
GASKET DETAILS:
SYNTHETIC RUBBER CORK 062 INCH THICK
MIL-C-6183 TYPE 1 CLASS 1 GRADE B
Figure 11 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 40 of 58  LS

### Page 42 (OCR)

SERVICE BULLETIN 84-57-09
MANIFOLD
WAS 82822053-103
NOW 82822053 - 105
(82822063 TUBE ASSY) ~  (AN960C1216 WASHER) 14  (AN924-8D NUT)
- 82822058 TUBE ASSY)
(82822064 TUBE ASSY) -
O-RING -  - (AN924-10J NUT)
MS29512-10  • 92003001296018-101 CHECK VALVE
(82822059 TUBE ASSY)
POCKETSIDE
DETAIL M
SCALE: 1/1
LHS ONLY
>
(STGR 17 TRACE)
(STGR 16 TRACE)
VIEW Y-Y
SCALE: 1/2
ROTATED 90*  CW
SHOWING APPLICATION OF PROTECTIVE FINISH
Figure 12
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 41 of 58  LS

### Page 43 (OCR)

SERVICE BULLETIN 84-57-09
- 791.200
14 (MS20002C9 WASHER, CSK)  (AN924-6J NUT)
TUEE ASSY
O-RING  82822064
MS29512-06
ADAPTER
WAS 82822105-101
NOW 82822105 - 103
(STGR 4 DATUM)
DETAIL N
SCALE:  1/1
-Ø1.13
POCKET SIDE
VIEW W-W
SHOWING APPLICATION OF PROT  PROTECTIVE FINISH
Figure 13
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 42 of 58  LS

### Page 44 (OCR)

SERVICE BULLETIN 84-57-09
-·92. 136)
(85713097)
VIEW U-U
ROTATED 180*
LHS SHN, RHS OPF
LOOKING NORMAL TO FRONT SPAR DATU
Figure 14
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 43 of 58  ILS

### Page 45 (OCR)

SERVICE BULLETIN 84-57-09
DETAIL  SCAVENE: TAIVE FLOW INST  DETAIL B
FUEL VENT LINE INSTL  ENGINE FEED INSTL
FUE EAT LINE FAST.  DETAIL C
REFUEL/DEFUEL INSTL
Figure 15 Sheet 1
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 44 of 58  I LS

### Page 46 (OCR)

SERVICE BULLETIN 84-57-09
IMPORTANT NOTICES FOR FIGURES 16 THRU 23
QUANTITY AND LOCATION OF B0305025A
COUPLINGS ON SOME AIRCRAFT MAY NOT  • MATCH
SOME OF THE VIEWS GIVEN ON FIGURES 16 THRU 23
ALL B0305025A COUPLINGS MUST BE REPLACED
BY B0305080A COUPLINGS.
IF THE SLEEVE AND O-RINGS OF A B0305025A
COUPLING ARE NOT  DISTURBED,  IT IS
ACCEPTABLE  TO REPLACE THE CLAM SHELL ONLY
WITHOUT  • REPLACING THE SLEEVE AND THE
O-RINGS
Figure 15 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 45 of 58  I LS

### Page 47 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS COUPLING BO305025A12
AND RELATED O-RING
NOW COUPLING B0305080A12
O-RING MS29513-117
FROM ENGINE
(82822132)  SERVICE BULLETIN 84-57-09
Figure 16
(82822129)
(828221301  L (82822131)  (82822151) (82822127)
DETAIL A
SCALE: 1/4
PLAN VIEW
S.B. 84-57-09  WAS COUPLING BO305025A12  SCAVENGE  LHS SHN, RAS OPP  MOTIVE FLOW INSTL
Page 46 of 58  AND RELATED O-RING
NOW COUPLING B0305080A12
O-RING MS29513-117

### Page 48 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  - 157.825  - 136.300  - 79.700  - 60.900
Figure 17  REMOVE & DISCARD  LHS & RAS  REMOVE & DISCARD  LHS  RH-S  REMOVE & DISCARD  SERVICE BULLETIN 84-57-09
AN935-10L WASHER  AN735D12 CLAMP  AN735D12 CLAMP
AN960D1OL WASHER (QTY 3)  AN935-10L WASHER  AN935-10L WASHER
MS21042L3 NUT  AN960D1OL WASHER (QTY 2)  AN960D1OL WASHER (QTY 3)
MS35207-263 SCREW (QTY 2)  MS21042L3 NUT  MS21042L3 NUT
AN960-10 WASHER  M535207-263 SCREW  MS35207-263 SCREW (QTY 2)
AN735D12 CLAMP  AN960-10 WASHER  AN960-10 WASHER
CSP476-7BB6 IMPER  CSP476-7BB6 AMPER  CSP476-7B86 AMPER
Page 47 of 58  S.B. 84-57-09  VIEW LOOKING FORWARD
ON LEFT WING REAR SPAR
LS

### Page 49 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006
Figure 18 Sheet 1  (82822139)  (Te 182822046)  [82822021]  (V952-16) 82822020)  N2622018) 228  SERVICE BULLETIN 84-57-09
REAR SPAR  WAS  WAS
COUPLING B0305025A16  COUPLING B0305025A16
O-RING MS29513-214  O-RING MS29513-214
NOW  NOW
COUPLING B0305080A16  COUPLING B0305080A16
O-RING MS29513-214  O-RING MS29513-214
Page 48 of 58  S.B. 84-57-09  NOTE:  LEFT WING TOP VIEW SHOWN.
DETAIL B  SCALE:  1/4  REFER TO FIGURE 18 SHEET 2  FOR VIEW LOOKING FORWARD
ENGINE FED  ON REAR SPAR
LS

### Page 50 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS
COUPLING B0305025A16
O-RING MS29513-214
0.000
- 173.200  - 136.300  - 117.500  - 79.700  - 42.000
NOW  SERVICE BULLETIN 84-57-09
COUPLING
B0305080A16
O-RING
MS29513-214
Figure 18 Sheet 2  2822075)
WAS  82822145)-
COUPLING B0305025A16
O-RING MS29513-214
COUPLING B0305080A16
O-RING MS29513-214
Page 49 of 58  S.B. 84-57-09  VIEW LOOKING FORWARD
ON AFT SIDE OF REAR SPAR

### Page 51 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006
Figure 19 Sheet 1  1082151)  - (4952-16€  SERVICE BULLETIN 84-57-09
11.20
WAS
WAS  WAS
REAR SPAR  COUPLING B0305025A16  O-RING MS29513-214  COUPLING B0305025A16  O-RING MS29513-214  O-RING MS29513-214  COUPLING B0305025A16
NOW  NOW  NOW
O-RING MS29513-214  COUPLING B0305080A16  COUPLING B0305080A16  O-RING MS29513-214  COUPLING B0305080A16  O-RING MS29513-214
Page 50 of 58  S.B. 84-57-09  DETAIL B  NOTE:  RIGHT WING TOP VIEW SHOWN.
SCALE: 1/4  REFER TO FIGURE 19 SHEET 2 FOR
PLAN VIEW  VIEW LOOKING FORWARD ON
ENGINE FEED INSTL  REAR SPAR

### Page 52 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS COUPLING
B0305025A16
0.000  42.000  MS29513-214  O-RING  79.700  136.300  157.825
NOW  COUPLING  SERVICE BULLETIN 84-57-09
B0305080A16
O-RING
MS29513-214
Figure 19 Sheet 2  (82822146)  WAS
COUPLING B0305025A16
O-RING MS29513-214
NOW
VIEW LOOKING FORWARD  COUPLING B0305080A16
O-RING MS29513-214
ON AFT SIDE OF REAR SPAR
RIGHT WING
Page 51 of 58  S.B. 84-57-09

### Page 53 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS CAP 82822076-103
AND RELATED O-RING
NOW CAP 82822076-105
O-RING MS29512-04
Figure 20 Sheet 1  (82822150  PECURES  SERVICE BULLETIN 84-57-09
(82822040)-
WASCOUPLINGS  WAS COUPLINGS
B0305025A16  B0305025A20
AND RELATED  AND RELATED
O- RINGS  O-RINGS
Page 52 of 58  S.B. 84-57-09  NOTE:  LEFT WING TOP VIEW SHOWN.  NOW COUPLING  B0305080A16  NOW COUPLINGS  B0305080A20
REFER TO FIGURE 18 SHEET 2  FOR VIEW LOOKING FORWARD  MS29513-214  O- RINGS  O-RINGS  MS29513-218
ON REAR SPAR
LS

### Page 54 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006
- 117.500  - 98.600  - 79.700  WAS
COUPLING BO305025A28
AND RELATED O-RINGS  NOW  SERVICE BULLETIN 84-57-09
) -RING MS29513-224
COUPLING BO305080A28
Figure 20 Sheet 2  WAS
COUPLING BO305025A20
AND RELATED O-RINGS
RESTRICTOR TUBE ASSEMBLY  NOW
COUPLING BO305080A20
O-RING MS29513-218  - 60.900  -8.600
NOTE:
MAKE SURE THAT THE OPEN END
OF RESTRICTOR TUBE ASSEMBLY
S.B. 84-57-09  82822102 IS INSTALLED PARALLE
Page 53 of 58  WITH THE LOWER SKIN. CON-
TACT WITH THE LOWER SKIN IS  VIEW LOOKING FORWARD
NOT PERMITTED.  ON AFT SIDE OF REAR SPAR LEFT
WING

### Page 55 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS  COUPLING B0305025A20  NOTE:
AND RELATED O-RINGS  MAKE SURE THAT THE OPEN END
NOW COUPLING B0305080A20  OF RESTRICTOR TUBE ASSEMBLY
O-RING MS29513-218  RESTRICTOR TUBE ASSEMBLY  82822102 IS INSTALLED PARALLE
WITH THE LOWER SKIN. CON-
TACT WITH THE LOWER SKIN IS
REFER TO
NOT PERMITTED.
FIGURE 3
(N2, 002102)  SERVICE BULLETIN 84-57-09
- (82822036)
Figure 21  - (82822136)
28221501
828020401
828220
82822041)
WAS  COUPLING
B0305025A16
REFER TO  FIGURE 3  O- RINGS  AND RELATED  WAS COUPLING B0305025A28  AND RELATED O-RINGS
NOW COUPLING  NOW COUPLING B0305080A28
B0305080A16  O-RING MS29513-224
S.B. 84-57-09  O-RINGS
Page 54 of 58  MS29513-214  PRESSURE RELIEF VALVE SERVO LINE  NOTE:
RIGHT WING TOP VIEW
SHOWN

### Page 56 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS COUPLING BO305025A16
AND RELATED O-RING
NOW COUPLING BO305080A16  REMOVE AND DISCARD  REMOVE AND DI
O-RINGS MS29513-214  (QTY 2).  WAS1801-3-8 SCREW  NB60D10L WASHER (QTY 2)  NAS1801-3-8 :  AN960D1OL WA  (QTY 2),  SERVICE BULLETIN 84-57-09
ASHER,  HS21042-3 NUT &  H521042-3 NJ
0N735D16 CLAMP  AN735D12 CLAI
PER
(85713811)
487:8P
Figure 22
(82822257)
ASHER (OTY 2).
WAS COUPLING BO305025A12  WAS COUPLING BO305025A12
AND RELATED O- RINGS  AND RELATED O-RINGS
NOW COUPLING BO305080A12  O-RINGS MS29513-117  NOW COUPLING BO305080A12  O-RINGS MS29513-117
Page 55 of 58  S.B. 84-57-09  NOTE:
LEFT WING TOP VIEW SHOWN.
RIGHT WING SIMILAR SPAR

### Page 57 (OCR)

Revision 'B' 03 Sep 2008  27 Jun 2006  WAS COUPLING B0305025A16
AND RELATED O-RING
NOW COUPLING B0305080A16
O-RING MS29513-214
(82822090)  (82822093) (82822103)  (82822104)  SERVICE BULLETIN 84-57-09
Figure 23 Sheet 1  ( 82822252)
(82822094)
REMOVE & DISCARD
AN735D16 LOCK VASHER
4960010L WASHER (QTY 2),
NAS1801-3-9 SCREW,
521042-3 NUT &
REMOVE & DISCARD
AS1801-3-8 SOREV.  WAS COUPLING B0305025A16
N96001OL WASHER (QTY 2),  N960D10 WASHER.  AND RELATED O-RING
W935-10L LOCK WASHER &
S21042-3 NUT  NOW COUPLING B0305080A16
O-RING MS29513-214
Page 56 of 58  S.B. 84-57-09  DETAIL E
LS

### Page 58 (OCR)

SERVICE BULLETIN 84-57-09
- Y102D 42.00
82822095
TUBE
85714435
BRACKET
NAS1801-3-11 SCREW
AN960D10L WASHER
85714404
BRACKET
VIEW F-F
Figure 23 Sheet 2
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 57 of 58  I LS

### Page 59 (OCR)

SERVICE BULLETIN 84-57-09
This Page Intentionally Blank
27 Jun 2006  S.B. 84-57-09
Revision 'B' 03 Sep 2008  Page 58 of 58  ILS

### Page 60 (OCR)

BOMBARDIER
SERVICE BULL @ SERIES DASH 8 AIRCRAFT RPORATION
To:  Partner Data Co-Ordinator (Toronto), Bombardier Aerospace Commercial Aircraft
Phone:  (1) 416 375 3534  Facsimile:  (1) 416 375 4538
E-mail: cmdb.requests@aero.bombardier.com
From:
Company:
Phone:  Extn:
Facsimile:  Date:
E-mail:
The data that you provide below will help us record the incorporation of this ModSum
and the aircraft effectivity in the maintenance manual.
Operator:  Service Bulletin:  Revision:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Aircraft Serial Number:  Model Number:  Date Bulletin Completed:
Fax this sheet to (1) 416 375 4538 or Email PDF to:
cmdb.requests@aero.bombardier.com

The text continues at https://openairdocs.org/service-documents/bombardier/sb-84-57-09/file/73911f0b48d0.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
