# Bombardier Temporary Revision Q300 52-042

Copy: No revision named ("Q300 AMM TR 52-042"), 44 pages: PDF https://openairdocs.org/files/sha256/06/a7/06a7df664f50c0bcc16120ac6c3cc2dbb0445e76b05680d52641a7c3990cc8bc; text https://openairdocs.org/service-documents/bombardier/tr-q300-52-042/file/06a7df664f50.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0586, the docket of AD 2018-20-11. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Other document (Temporary Revision)
- Number: Q300 52-042
- Page: https://openairdocs.org/service-documents/bombardier/tr-q300-52-042

## Text (44 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0586, the docket of AD 2018-20-11. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

TEMPORARY REVISION 52−042
FILING INSTRUCTIONS: This Temporary Revision (TR52−042) replaces TR52−041. Put this
Temporary Revision against pageblock AMM52−20−16−02, page
201.
Record the insertion of this Temporary Revision on the yellow
RECORD OF TEMPORARY REVISIONS sheet at the front of this
chapter.
DESCRIPTION: This Temporary Revision replaces TR52−041 to correct and clarify
the access panels for replacement of bearings from their respective
lever assemblies.
**ON A/C ALL
FORWARD EMERGENCY EXIT DOOR − MAINTENANCE PRACTICES
1. General
The maintenance procedures that follow are for the type I emergency exit door, type I
emergency exit door seal and the type I emergency exit door bearings. The door is installed
on the right hand side of the fuselage opposite to the passenger airstair door. The door
incorporates a window and can be opened by either the internal or the external handles.
These procedures include:
– Removal and installation of the type I emergency exit door
– Removal and installation of the type I emergency exit door seal
– Removal and installation of the type I emergency exit door assist handle
– Replacement of the bearings installed in the type I emergency exit door handle
mechanism
– Rigging of the type I emergency exit door operating mechanism
– Inspection of the type I emergency exit door.
2. Removal/Installation
Equipment and Materials:
– Force Gauge − 0 to 50 lbf (0 to 222.41 N)
– Solvent
– Plastic Scraper
– Cloth, Lint−free
– Adhesive − EC1357N or EC847
– Sealant − RTV 102 or RTV 732
A. Remove Forward Emergency Exit Door
Refer to Figure 201.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 1 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 2

CAUTION: DOOR WILL FALL FREELY FROM AIRCRAFT WHEN OPERATING
HANDLE IS ACTUATED. ENSURE ADEQUATE SUPPORT IS
AVAILABLE TO PREVENT DAMAGE TO DOOR STRUCTURE.
(1) Operate internal door handle (EMERGENCY PULL) to rotate the lift and latch shaft
rollers in their respective followers.
NOTE: When type I emergency exit is opened for maintenance purposes, make
sure that two persons are available to hold the weight of the door. The
type I door is heavier than the type II exit doors and there is no
counterbalance system.
NOTE: The maximum force necessary to fully operate the internal door handle is
less than 40 lbf (177.92 N).
(2) Lift door upward and outward to clear opening in fuselage.
B. Install Forward Emergency Exit Door
Refer to Figure 201.
(1) Move external operating handle to "fully open" position.
(2) Position door at door surround by locating upper and lower cam followers in their
respective cams (AB) and (AC) and two spigots in guide cams (AD).
(3) Move external handle to "fully closed" position to close door, and return handle to
recess.
(4) Make sure that the forward emergency exit door seal inflates correctly.
NOTE: If necessary, pressurize the door seal reservoir to 18 psi (124.1 kPa) at
the charging valve in the wardrobe.
**ON A/C 100, 108, 116, 124, 131, 137, 143, 149, 154, 159, 164, 169, 174, 180, 182, 184, 186,
188, 190, 192, 194, 196, 198, 200, 202, 210, 216, 221, 224, 230, 232, 234, 240, 242, 244, 246,
248, 250, 252, 254, 256−257, 259, 261−262, 264, 266−267, 269, 271−272, 274, 276, 278−279,
281, 283−284, 286, 288, 290−291, 293, 295−296, 298, 300−301, 303, 305, 307, 309, 311, 313,
315, 319−320, 323, 325, 332, 334, 336, 338, 340, 342, 348, 350, 352, 354, 356, 358, 368, 370,
374−375, 379, 381, 385, 393, 395, 397, 399−402, 404−406, 408, 410, 412, 414−416, 420,
422−423, 438, 442−443, 451, 458, 462, 464, 466−467, 474, 481, 483, 485, 487, 489, 499, 503,
505, 508, 517, 519, 521, 523, 525, 527, 531, 533−534, 538−539, 543−546, 548−549, 552−557,
560−565, 567−571, 573−578, 580−583, 586−590, 592 Pre SB8−52−60
C. Remove Forward Emergency Exit Door Seal
Refer to Figure 202
(1) Remove the emergency exit door from the aircraft (refer to para. 2. A).
(2) Put the door on a applicable work bench.
(3) Remove the door and window trim panels as necessary to get access to the
pneumatic connector assembly.
(4) Loosen the clamp (4) on the air inlet hose (6) which connects the air valve (2) to the
seal (1).
(5) Disconnect the air inlet hose (6) from the air valve (2) and remove the sleeve (5)
and the clamp (4). Keep the removed hardware for the installation procedure.
(6) Put a protective plug on the open end of the elbow (3).
(7) Hold the seal (1) tightly with the fingers. Remove the air inlet assembly through the
inlet hole.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 2 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 3

(8) Remove the seal (1) from the seal retainer until the seal is free from the door.
(9) Discard the seal (1).
D. Install Forward Emergency Exit Door Seal
Refer to Figure 202
(1) Examine the new seal (1) for the good condition.
(2) If necessary, clean the seal (1) with the solvent (Refer to AMM51−27−01).
(3) Dry the seal (1) with a lint free cloth before the solvent dries.
(4) Clean the used adhesive from the seal retainer with the plastic scraper.
(5) Clean the seal retainer with solvent (Refer to AMM51−27−01).
(6) Dry the seal retainer with a lint free cloth before the solvent dries.
(7) Apply adhesive to the bonding surface of the seal retainer.
(8) Install the air inlet assembly of the seal (1) through the air inlet hole.
(9) Compress the seal (1) with your fingers into the seal retainer.
NOTE: During installation, do not twist or stretch the seal.
(10) Connect the air inlet hose (6) to the air valve (2) as follows:
(a) Remove the protective plug from the open end of the elbow (3).
(b) Put the clamp (4) and the sleeve (5) on the air inlet hose (6).
(c) Install the air inlet hose (6) with the sleeve (5) to the air valve (2). This
connects the air valve (2) to the seal (1).
(d) Tighten the clamp (4) on the air inlet hose (6).
(11) Install the emergency exit door (refer to para. 2. B).
(12) Do the pressurization leak test (Refer to AMM21−30−00).
**ON A/C 594−605, 607−611, 613−625, 627−636, 638−645, 647−648, 650−654, 656−660,
662−663, 667−672 and ON A/C 100, 108, 116, 124, 131, 137, 143, 149, 154, 159, 164, 169, 174,
180, 182, 184, 186, 188, 190, 192, 194, 196, 198, 200, 202, 210, 216, 221, 224, 230, 232, 234,
236, 238, 240, 242, 244, 246, 248, 250, 252, 254, 256−257, 259, 261−262, 264, 266−267, 269,
271−272, 274, 276, 278−279, 281, 283−284, 286, 288, 290−291, 293, 295−296, 298, 300−301,
303, 305, 307, 309, 311, 313, 315, 319−320, 323, 325, 332, 334, 336, 338, 340, 342, 348, 350,
352, 354, 356, 358, 365, 368, 370, 374−375, 379, 381, 385, 393, 395, 397, 399−402, 404−408,
410, 412, 414−416, 420, 422−423, 438, 442−443, 451, 458, 462, 464, 466−467, 474, 481, 483,
485, 487, 489, 491, 493, 495, 499, 503, 505, 508, 517, 519, 521, 523, 525, 527, 531−535,
538−539, 543−546, 548−549, 552−557, 560−565, 567−571, 573−578, 580−592 Post SB8−52−60
E. Remove Forward Emergency Exit Door Seal
Refer to Figure 203
(1) Remove the emergency exit door from the aircraft (refer to para. 2. A).
(2) Put the door on a applicable work bench.
(3) Remove the door and window trim panels as necessary to get access to the
pneumatic connector assembly.
(4) Loosen the clamp (3) on the air inlet hose (2) which connects the air valve to the
seal (1).
(5) Disconnect the air inlet hose (2) from the coupling (4).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 3 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 4

(6) Remove the clamp (3). Keep the removed hardware for the installation procedure.
(7) Put a protective plug on the open end of the coupling (4).
(8) Hold the seal (1) tightly with the fingers. Remove the air inlet assembly through the
inlet hole.
(9) Remove the seal (1) from the seal retainer until the seal is free from the door.
(10) Discard the seal (1).
F. Install Forward Emergency Exit Door Seal
Refer to Figure 203
(1) Examine the new seal (1) for the good condition.
(2) If necessary, clean the seal (1) with solvent (Refer to AMM51−27−01).
(3) Dry the seal (1) with a lint free cloth before the solvent dries.
(4) Clean the used adhesive from the seal retainer with the plastic scraper.
(5) Clean the seal retainer with solvent (Refer to AMM51−27−01).
(6) Dry the seal retainer with a lint free cloth before the solvent dries.
(7) Apply adhesive to the bonding surface of the seal retainer.
(8) Install the air inlet assembly of the seal (1) through the air inlet hole.
(9) Compress the seal (1) with your fingers into the seal retainer.
NOTE: During installation, do not twist or stretch the seal.
(10) Connect the air inlet hose (2) as follows:
(a) Remove the protective plug from the open end of the coupling (4).
(b) Put the clamp (3) on the air inlet hose (2).
(c) Install the air inlet hose (2) to the coupling (4). This connects the air valve to
the seal (1).
(d) Tighten the clamp (3) on the air inlet hose (2).
(11) Install the emergency exit door (refer to para. 2. B).
(12) Remove all the tools, equipment and unwanted materials from the work area.
(13) Do the pressurization leak test (Refer to AMM21−30−00).
**ON A/C 438, 442, 466, 481, 483, 485 Post SB8−25−154 and ON A/C 527, 531, 553−554,
584−585, 594 Post SB8−25−282
G. Remove the assist handle from the type I emergency exit door as follows:
Refer to Figure 204
(1) Turn the nylon nuts (5) clockwise to remove the handle (1).
(2) Remove the bolts (2), washers (3), bushings (6), nylon nuts (5), washers (4) and
the shims (7) from the handle (1) and door.
H. Install the assist handle from the type I emergency exit door as follows:
Refer to Figure 204
(1) Install the nylon nuts (5) with the washers (4), bushings (6), washers (3), bolt (2)
and the shims (7).
(2) Tighten the bolt (2).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 4 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 5

(3) Put the handle (1) on the nylon nuts (5).
(4) Turn the nylon nuts (5) counterclockwise to install the handle (1) to the door.
**ON A/C ALL
I. Replacement of the bearing installed in the type I emergency exit door handle
mechanism.
Refer to Figure 205
(1) Equipment and materials:
– 04−03 − Grease, aircraft and instrument, gear and actuator screw
– 04−06 − Synthetic grease − General purpose, wide temperature range
– 07−01 − F 13 Coating − Compound, corrosion preventive, (hard, soft film,
moisture displacing)
– 08−26 − Solvent − MPK (Methyl n−Propyl Ketone, by Eastman Chemical)
– 14−02 − Wiper cloth − white cotton (lint free)
(2) Remove the type I emergency exit door (Refer to para 2.A).
(3) Remove the type I emergency exit door panel (Refer to AMM 25−22−05).
(4) There are no covers on panels (5), (6), (7), and (8). However, you may have to
remove the panel cover (18) and brackets (19) for other bearings, if required (Refer
to Figure 205, sheet 1 of 6).
WARNING: YOU MUST WEAR EYE PROTECTION WHEN YOU CUT THE
COTTER PIN. WHEN YOU CUT THE COTTER PIN, PIECES CAN
HIT YOUR EYES AND CAUSE INJURIES.
WARNING: YOU MUST WEAR EYE PROTECTION WHEN YOU CUT THE
LOCKWIRE. WHEN YOU CUT THE LOCKWIRE, PIECES CAN HIT
YOUR EYES AND CAUSE INJURIES.
(5) Replace the bearings (1) and (2) from the upper crank (4) as follows:
(a) Remove the upper crank (4) as follows:
1 Remove the nuts (11), washers (10) and bolts (9), (12) from the center
shaft (13).
2 Remove the upper crank (4) from the type I emergency exit door (15).
3 If necessary, remove the washers (20) from the upper crank (4).
(b) Remove the bearings (1) from the housings (3) (Refer to AMM 20−19−02).
(c) Remove the bearings (2) from the housings (14) (Refer to AMM 20−19−02).
(d) If the bearings (1) and (2) are corroded, discard them.
(e) Clean the housings (3) and (14) with a lint free cloth moist in the solvent.
(f) Apply corrosion preventive compound (07−01) to the housings (3) and (14)
(Refer to AMM 20−16−01).
(g) Apply grease (04−03) or (04−06) to the bearings (1) and (2).
(h) Install the bearings (1) and (2) to the housings (3) and (14) (Refer to AMM
20−19−02).
(i) If removed, install the washers (20) to the upper crank (4).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 5 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 6

(j) Connect the upper crank (4) with the center shaft (13) with the bolts (9), (12),
washers (10) and the nuts (11).
(6) Replace the bearings (16) and (17) from the lower crank (27) as follows:
(a) Remove the lower crank (27) as follows:
1 Remove the nuts (26), washers (25) and bolts (24) from the lower shaft
(28).
2 Remove the lower crank (27) from the type I emergency exit door (15).
3 If necessary, remove the washers (21) from the lower crank (27).
(b) Remove the bearings (16) from the housings (22) (Refer to AMM 20−19−02).
(c) Remove the bearings (17) from the housings (23) (Refer to AMM 20−19−02).
(d) If the bearings (16) and (17) are corroded, discard them.
(e) Clean the housings (22) and (23) with a lint free cloth moist in the solvent.
(f) Apply corrosion preventive compound (07−01) to the housings (22) and (23)
(Refer to AMM 20−16−01).
(g) Apply grease (04−03) or (04−06) to the bearings (16) and (17).
(h) Install the bearings (16) and (17) to the housings (22) and (23) (Refer to AMM
20−19−02).
(i) If removed, install the washers (21) to the lower crank (27).
(j) Connect the lower crank (27) with the lower shaft (28) with the bolts (24),
washers (25) and the nuts (26).
(7) Replace the bearing (30) from the handle assembly (31) as follows:
(a) Remove and discard the cotter pin (29).
(b) Remove the nut (44), washers (43), (41), bushing (42) and the bolt (40) from
the rod assembly (39).
(c) Disconnect the rod assembly (39) from the handle assembly (31).
(d) Remove and discard the cotter pin (37).
(e) Remove the nut (36), washers (33), (35), bushing (34) and the bolt (32) from
the handle assembly (31).
(f) Remove the handle assembly (31) from the support plate (38).
(g) Remove the bearing (30) from the handle assembly (31) (Refer to AMM
20−19−02).
(h) If the bearing (30) is corroded, discard it.
(i) Clean the handle assembly (31) and the support plate (38) with a lint free cloth
moist in the solvent.
(j) Apply corrosion preventive compound (07−01) to the handle assembly (31)
and the support plate (38) (Refer to AMM 20−16−01).
(k) Apply grease (04−03) or (04−06) to the bearing (30).
(l) Install bearing (30) to the handle assembly (31) (Refer to AMM 20−19−02).
(m) Install the handle assembly (31) to the support plate (38) with the bolt (32),
washers (33), (35), bushing (34) and the nut (36).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 6 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 7

(n) Safety the nut (36) with the new cotter pin (37).
(o) Install the rod assembly (39) to the handle assembly (31) with the bolt (40),
washers (43), (41), bushing (42) and nut (44).
(p) Safety the nut (44) with the new cotter pin (29).
(8) Replace the bearings (45) and (46) from the lever assembly (52) as follows:
NOTE: Keep the removed hardware for the installation procedure.
(a) Remove and discard the cotter pin (50) from the nut (49).
(b) Remove the nut (49), bolt (47), washer (48) and the bushing (51).
(c) Disconnect the rod assemblies (61) and (62) from the lever assembly (52).
(d) Remove and discard the lockwire from the bolt (54).
(e) Remove the bolt (54), washers (58) and (111) and the bushing (59).
(f) Remove the nut (57), washer (56) and the bolt (55) to remove the housing
(53).
(g) Remove lever assembly (52) from the housing (53).
(h) If the bearings (45) and (46) are corroded, discard them.
(i) If necessary, remove the spacer (60) from the lever assembly (52).
(j) Clean the area and apply corrosion preventive compound (07−01) on the lever
assembly (52) (Refer to AMM 20−16−01).
(k) If removed, install the spacer (60) to the lever assembly (52).
(l) Install new bearings (45) and (46) on the lever assembly (52).
(m) Apply grease (04−03) or (04−06) to the bearings (45) and (46) (Refer to AMM
20−16−01 and AMM 20−19−02).
(n) Install the housing (53) with the bolt (55), washer (56) and the nut (57).
(o) Install the bolt (54), washers (58) and (111) and the bushing (59) to connect
the lever assembly (52) with the housing (53).
(p) Safety the bolt (54) with lockwire.
(q) Install rod assemblies (61) and (62) to the lever assembly (52) with the bolt
(47), washer (48), nut (49) and the bushing (51).
(r) Safety the nut (49) with the new cotter pin (50).
(9) Replace the bearings (63) and (64) from the lever assembly (67) as follows:
NOTE: Keep the removed hardware for the installation procedure.
(a) Remove and discard the cotter pins (78) from the nuts (77).
(b) Remove the nuts (77), bolts (75), washers (76) and the bushings (79).
(c) Disconnect the rod assemblies (65) and (66) from the lever assembly (67).
(d) Remove and discard the lockwire from the bolt (68).
(e) Remove the bolt (68), washers (69) and (81) and the bushing (70).
(f) Remove the nut (74), washer (73) and the bolt (72) to remove the housing
(80).
(g) Remove the lever assembly (67) from the housing (80).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 7 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 8

(h) If the bearings (63) and (64) are corroded, discard them.
(i) If necessary, remove the spacer (71) from the lever assembly (67).
(j) Clean the area and apply corrosion preventive compound (07−01) on the lever
assembly (67) (Refer to AMM 20−16−01).
(k) If removed, install the spacer (71) to the lever assembly (67).
(l) Install new bearings (63) and (64) on the lever assembly (67).
(m) Apply grease (04−03) or (04−06) to the bearings (63) and (64) (Refer to AMM
20−16−01 and AMM 20−19−02).
(n) Install lever assembly (67) to the housing (80) with the bolt (68), washers (69)
and (81) and the bushing (70).
(o) Safety the bolt (68) with lockwire.
(p) Install the housing (80) with the bolt (72), washer (73) and the nut (74).
(q) Install rod assemblies (65) and (66) to the lever assembly (67) with the bolts
(75), washers (76), nuts (77) and the bushings (79).
(r) Safety the nuts (77) with the new cotter pins (78).
(10) Replace the bearings (86) and (87) from lever assemblies (88) and (89) as follows:
NOTE: Keep the removed hardware for the installation procedure.
(a) Remove the bolts (84), (102) and the washers (85), (103).
(b) Remove the cover plate (83).
(c) Remove and discard lockwire from the bolts (95) and (92).
(d) Remove bolts (95) and washers (96).
(e) Remove the bolt (92), washers (93), spacer (110) and the bushing (94).
(f) Remove the housing (91).
(g) Remove the lever assemblies (88) and (89) from the housing (91).
(h) Remove and discard the cotter pin (100) from the nut (99).
(i) Remove the nut (99), bolt (97), washers (98) and (112) and the bushings
(101).
(j) Disconnect the rod assembly (105) from the lever assembly (88).
(k) If the bearing (86) is corroded, discard it.
(l) Clean the area and apply corrosion preventive compound (07−01) on the lever
assembly (88) (Refer to AMM 20−16−01).
(m) Install new bearing (86) on the lever assembly (88).
(n) Apply grease (04−03) or (04−06) to the bearing (86) (Refer to AMM 20−16−01
and AMM 20−19−02).
(o) Remove and discard the cotter pin (82) from the nut (109).
(p) Remove the nut (109), bolt (106), washer (108) and the bushing (107).
(q) Disconnect the rod assembly (104) from lever assembly (89).
(r) If the bearing (87) is corroded, discard it.
(s) Clean the area and apply corrosion preventive compound (07−01) on the lever
assembly (89) (Refer to AMM 20−16−01).
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 8 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 9

(t) Install new bearing (87) on the lever assembly (89).
(u) Apply grease (04−03) or (04−06) to the bearing (87) (Refer to AMM 20−16−01
and AMM 20−19−02).
(v) Install the lever assemblies (88) and (89) and the housing (91) with the bolt
(92), washers (93), spacer (110) and the bushing (94).
(w) Connect the rod assembly (105) to the lever assembly (88) with the bolt (97),
washers (98) and (112), nut (99) and the bushing (101).
(x) Safety the nut (99) with the new cotter pin (100).
(y) Connect the rod assembly (104) to the lever assembly (89) with the bolt (106),
washer (108), nut (109) and the bushing (107).
(z) Safety the nut (109) with the new cotter pin (82).
(aa) Install the bolts (95) and the washers (96) to the housing (91).
(ab) Safety the bolts (95) and (92) with the lockwire.
(ac) Install the cover plate (83) with the bolts (84), (102) and the washers (85),
(103).
(11) Install the access panels (5), (6), (7), (8), (18) and (19), as applicable (Refer to
SRM 52−30−11).
(12) Install the type I emergency exit door panel (Refer to AMM 25−22−05).
(13) Install the type I emergency exit door (Refer to para 2.B).
(14) Do an adjustment test of the type I emergency exit door (15) (Refer to Para 3).
(15) Open and close the door two times to make sure smooth movement with no
interference to the liners.
(16) Do a handle preload check (Refer to Para 3.I).
(17) Remove all tools, equipment and unwanted materials from the work area.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 9 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 10

dam03_5220162_001.dg, rt/vk, nov25/2010
AD
AB N
FUSELAGE
SKIN
0.030 in. (0.76 mm)
MINIMUM
DOOR SKIN
SPIGOT
GUIDE CAM
PRESSURE
STOPLIFT CAM
ROLLER
RETAINER
SEAL
FILLET SEAL
ADHESIVE
AC
T
SERRATED
PLT & SHIM
PROXIMITY
SENSOR
TARGET
GAP
ADJUSTING
NUT
LATCH
CAM
WITHOUT DOOR INSTALLED MIN. GAP 0.250 in.
(6.35 mm) WITH DOOR INSTALLED & LOCKED
POSITION GAP 0.010 in − 0.020 in. (0.25 − 0.51 mm).
NOTE
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 1 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 10 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 11

CLOSED
STOP BOLT
OPEN
STOP BOLT
LOWER TORQUE
TUBE ASSY
PUSH ROD
LEVER
STOP FITTING
A3
RIGGING PIN
dam03_5220162_002.dg, rt, 24/02/04
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 2 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 11 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 12

LEVER
PUSH ROD
RIGGING
PIN
UPPER TORQUE
TUBE ASSY
PUSH ROD
LEVER
RIGGING
PIN
STOP
FITTING
CLOSED
STOP BOLT
OPEN
STOP BOLT
PUSH ROD
LOWER TORQUE
TUBE ASSY
LEVER ASSY
PUSH ROD
RIGGING
PIN
INNER DOOR HANDLE
IN CLOSED & LOCKED
POSITION
INNER DOOR HANDLE
IN OPENED POSITION
A2
A1
A3
dam03_5220162_003.dg, rt/kmw, jun16/2011
F1
F2
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 3 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 12 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 13

dam03_5220162_004.dg, rt/gw, feb4/2010
FUSELAGE
SKIN
LEVER
DOOR SKIN
PUSH ROD
RIGGING
PIN
UPPER
TORQUE
ASSEMBLY
FUSELAGE SKIN
FUSELAGEFUSELAGE
SKIN
DOOR
A2
0.030 in. (0.76 mm)
MINIMUM
0.030 in. (0.76 mm)
MINIMUM
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 4 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 13 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 14

DOOR SKINFUSELAGE
SKIN
PRESSURE
STOP
FUSELAGE
SKIN
PRESSURE
STOP
DOOR SKIN
dam03_5220162_005.dg, rt/gw, feb4/2010
0.030 in. (0.76 mm)
MINIMUM
0.030 in. (0.76 mm)
MINIMUM
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 5 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 14 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 15

GUIDE CAM
SPIGOT
ROLLER
LIFT CAM
dam03_5220162_006.dg, rt/gw, feb4/2010
DOOR SKIN FUSELAGE
SKIN
PRESSURE
STOP
SERRATED
PLT & SHIM
LATCH
CAM
TARGET
MIN. GAP 0.250 in.  (6.35 mm) 
PROXIMITY
SENSOR
ADJUSTING
NUT
GAP 0.010 in − 0.020 in.
(0.25 − 0.51 mm)
AD
AB
AC
N
T
WITHOUT DOOR INSTALLED
WITH DOOR INSTALLED
& LOCKED POSITION
GAP
0.030 in. (0.76 mm)
MINIMUM
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 6 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 15 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 16

dam03_5220162_007.dg, gg/gv, 27/02/04
SERRATED
PLT & SHIM
LATCH
CAM
TARGET
MIN. GAP 0.250 in.  (6.35 mm) 
PROXIMITY
SENSOR
ADJUSTING
NUT
GAP 0.010 in − 0.020 in.
(0.25mm  − 0.51mm) AC
T
WITHOUT DOOR INSTALLED
WITH DOOR INSTALLED
& LOCKED POSITION
GAP
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
FORWARD EMERGENCY EXIT − INSTALLATION AND RIGGING
Figure 201 (Sheet 7 of 7)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 16 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 17

dam03_5220162_016.dg, nn, jul25/2012
2
3
4
5
6
1
Bond the seal with adhesive EC1357N or EC847.
NOTE
1. Seal.
2. Air valve.
3. Elbow.
4. Clamp.
5. Sleeve.
LEGEND  
6. Air inlet hose.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE I EMERGENCY EXIT DOOR SEAL − REMOVAL AND INSTALLATION
Figure 202
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 17 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 18

dam03_5220162_017.dg, nn, jul25/2012
AIR VALVE
(REF)
1. Seal.
2. Air inlet hose.
3. Clamp.
4. Coupling.
LEGEND  
2
3
4
1
Bond the seal with adhesive EC1357N or EC847.
NOTE
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE I EMERGENCY EXIT DOOR SEAL − REMOVAL AND INSTALLATION
Figure 203
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 18 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 19

dam03_5220162_022.dg, rs, jun23/2017
1
2
3 6
4
5
6
2
3
4
5
7
LEGEND  
1. Handle.
2. Bolt.
3. Washer.
4. Washer.
5. Nylon nut.
6. Bushing.
7. Shim.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE I EMERGENCY EXIT DOOR HANDLE − REMOVAL AND INSTALLATION
Figure 204
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 19 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 20

dam03_5220162_018.dg, rs/gv, jan23/2018
VIEW LOOKING OUTBOARD ON
TYPE I EMERGENCY EXIT DOOR
5. Panel.
6. Panel.
7. Panel.
8. Panel.
18. Panel.
19. Bracket.
LEGEND  
5
6
7
8
5
18
19
19 19
19
NOTES:
1. There are no cover panels on 5, 6, 7 and 8 locations.
2. Remove panel 18 or brackets 19 as required.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 1 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 20 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 21

dam03_5220162_019.dg, rs/gv, jan17/2018
VIEW LOOKING OUTBOARD ON
TYPE I EMERGENCY EXIT DOOR
SHOWING MECHANISM IN CLOSED POSITION
X170.24 X196.24
LEGEND  
15. Type I emergency exit door.
15
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 2 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 21 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 22

2
14
3
1
4
9
10
11
13
27
22
23
16
17
24
2526
28
dam03_5220162_020.dg, rs, feb23/2017
1. Bearing.
2. Bearing.
3. Housing.
4. Upper crank.
LEGEND  
11. Nut.
9. Bolt.
10. Washer.
12. Bolt.
27. Lower crank.
14
3
1
4
2
12
10
11
13
13. Center shaft.
14. Housing.
16. Bearing.
17. Bearing.
20. Washer.
21. Washer.
22. Housing.
23. Housing.
24. Bolt.
25. Washer.
26. Nut.
28. Lower shaft.
21
20
20
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 3 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 22 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 23

27
16
22
23
17
24
25
26
28
dam03_5220162_021.dg, rs, aug08/2017
38
31
32
33
36
35 37
34
4042
41
39
4429
30
43
LEGEND  
29. Cotter pin.
30. Bearing.
31. Handle assembly.
32. Bolt.
33. Washer.
34. Bushing.
35. Washer.
36. Nut.
37. Cotter pin.
38. Support plate.
39. Rod assembly.
40. Bolt.
41. Washer.
42. Bushing.
43. Washer.
44. Nut.
16. Bearing.
17. Bearing.
21. Washer.
22. Housing.
23. Housing.
24. Bolt.
25. Washer.
26. Nut.
27. Lower crank.
28. Lower shaft.
21
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 4 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 23 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 24

dam03_5220162_023.dg, nn/nn, apr04/2018
LEGEND  
55. Bolt.
56. Washer.
57. Nut.
58. Washer.
59. Bushing.
60. Spacer.
61. Rod assembly.
62. Rod assembly.
63. Bearing.
64. Bearing.
65. Rod assembly.
66. Rod assembly.
67. Lever assembly.
68. Bolt.
69. Washer.
70. Bushing.
45. Bearing.
46. Bearing.
47. Bolt.
48. Washer.
49. Nut.
50. Cotter pin.
51. Bushing.
52. Lever assembly.
53. Housing.
54. Bolt.
68
69
72
73 74
70 63
71
80
75 79
67
77
78 76
76 78
77
64
79
75
81
66
53
54
111
55
62
45
60
46
58
59
52
56
47
51
57
48
49
50
61
71. Spacer.
72. Bolt.
73. Washer.
74. Nut.
75. Bolt.
76. Washer.
77. Nut.
78. Cotter pin.
79. Bushing.
80. Housing.
81. Washer.
65
111. Washer.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 5 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 24 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 25

93
91
83
85
84
92
102 103
94
95
96
86
110
89
87
93
88
100
97
101
106
107
109
90
108
LEGEND  
92. Bolt.
93. Washer.
94. Bushing.
95. Bolt.
97. Bolt.
98. Washer.
99. Nut.
100. Cotter pin.
101. Bushing.
102. Bolt.
103. Washer.
104. Rod assembly.
105. Rod assembly.
106. Bolt.
107. Bushing.
108. Washer.
82. Cotter pin.
83. Cover plate.
84. Bolt.
85. Washer.
86. Bearing.
87. Bearing.
88. Lever assembly.
89. Lever assembly.
90. Housing.
91. Housing.
99
98
dam03_5220162_024.dg, nn/nn, apr04/2018
96. Washer.
109. Nut.
110. Spacer.
82
104
105
112
112. Washer.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
TYPE 1 EMERGENCY EXIT DOOR HANDLE MECHANISM BEARINGS − REPLACEMENT
Figure 205 (Sheet 6 of 6)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 25 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 26

3. Adjustment/Test
Rigging Type I Emergency Exit on the Bench
Refer to Figure 201.
A. Rigging the Door Operating Mechanism
Refer to Sheets 2 and 3.
(1) Loosen the limit stop bolts (M) and (L) to permit complete freedom of movement of
the stops.
(2) Position the inner and outer operating handles in the "closed and locked" position.
Make sure that the outer handle is retracted into the recess.
(3) Disconnect the push rods (D) and (F) at the lever assembly (E).
NOTE: The horizontal push rod from the outer handle assembly is fixed in length
− both ends are riveted.
(4) Rotate the lever (E) to align the rig pin holes in the lever with the slot in the
structure and insert the rig pin A1.
(5) Adjust the lengths of the push rods (D) and (F) to align the rod ends with the holes
in the lever. Tighten the jam nuts to keep this setting.
(6) Attach the push rods (D) and (F) to the lever (E) and safety the hardware.
(7) Remove the rig pin A1.
(8) With handles still in the "closed and locked" position, disconnect the push rod (G)
from the upper torque tube lever (J) and push rod (H) from the lower torque tube
lever (V).
(9) Rotate the upper torque tube assembly to align the rig pin hole in the lever (J) with
the slot in the structure and insert the rig pin A2.
(10) Adjust the length of the pushrod (G) until the rod end aligns with the hole in the
lever. Tighten the jam nuts to keep this setting.
(11) Attach the push rod (G) to the lever (J) and safety the hardware.
(12) Rotate the lower torque tube assembly to align the rig pin hole in the lever (V) with
the slot in the structure and insert the rig pin A3.
(13) Adjust the length of the push rod (H) until the rod end aligns with the hole in the
lever. Tighten the jam nuts to keep this setting.
(14) Attach the push rod (H) to the lever (V) and safety hardware.
(15) Remove the rig pins A2 and A3.
B. Limit Stop Bolt Settings
(1) Move the inner and outer operating handles to the "closed and locked" position.
(2) Adjust the stop bolt (L) just to contact the face of the stop fitting (K).
(3) Loosen the stop bolt (L) one half turn and tighten the jam nut to keep this setting.
(4) Rotate the outer handle to the "fully open" position. Adjust the stop bolt (M) just to
contact the face of the stop fitting (K).
(5) Rotate the outer handle to the "closed and locked" position.
(6) Screw in the stop bolt (M) one full turn and tighten the jam nut to keep this setting.
(7) Rotate the outer handle through the full cycle to make sure the complete freedom of
movement.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 26 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 27

(8) Do the step (7) again using the inner handle.
(9) Safety the heads of the stop bolts (M) and (L) with lockwire together as required.
C. Do a check of the type I emergency exit door for the vertical positioning (Gaps) as
follows: (Refer to Figure 206)
(1) Refer to the Table 201 for skin gaps − clearances between the door skin and the
door surround skin (fuselage). The gap measurements given in the table are taken
with the aircraft not pressurized.
(2) Make sure no fouling exists between the door skin and the door surround before
taking the measurements.
(3) Make sure that the door is centered before taking the gap measurements. If
necessary, open and close the door to center the door in the opening.
(4) Push the door outboard until the pressure stops are in contact. Measure the gaps
while the pressure stops are in contact.
(5) Measurements for the forward and aft edge gaps are taken at the pressure stops (4
places).
(6) Measurements for the forward and aft edge gaps are also taken at the midpoint.
NOTE: Mid point − An approximate half distance between the top pressure stops
and the bottom pressure stops of the door.
TABLE 201
EMERGENCY EXIT DOOR TYPE I VERTICAL POSITIONING − GAPS (Aircraft Not Pressurized)
APPLICABLE AREA GAPS (CLEARANCE)
Forward Edge 0.030 in. (0.76 mm) Minimum
(Refer to the Notes below)
(Refer to the Note 5)
Aft Edge 0.030 in. (0.76 mm) Minimum
(Refer to the Notes below)
(Refer to the Note 5)
Upper Edge 0.030 in. (0.76 mm) Minimum
(Refer to Notes 1, 2 and 6)
Lower Edge 0.030 in. (0.76 mm) Minimum
(Refer to Notes 1, 2 and 6)
NOTE: # 1. Make sure that the door is centered before taking the measurements. If necessary,
open and close the door to center the door in the opening.
NOTE: # 2. Push the door outboard until the pressure stops are in contact. Measure the gaps
while the pressure stops are in contact.
NOTE: # 3. Measurements for the forward and aft edge gaps are taken at the pressure stops (4
places).
NOTE: # 4. Measurements for the forward and aft edge gaps are also taken at the midpoint.
NOTE: # 5. Clearance of minimum 0.030 in. (0.76 mm) is permissible for the Forward and Aft
edges provided that the sum of each respective pair (Forward and Aft measurement
locations) of clearance does not exceed 0.210 in. (5.33 mm). Make sure no fouling
exists between the door skin and the door surround structure.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 27 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 28

TABLE 201
EMERGENCY EXIT DOOR TYPE I VERTICAL POSITIONING − GAPS (Aircraft Not Pressurized)
NOTE: # 6. Clearance of minimum 0.030 in. (0.76 mm) is permissible for the Upper and Lower
edges provided that the sum of each respective pair (Upper and Lower measurement
locations) of clearance does not exceed 0.375 in. (9.52 mm). Make sure no fouling
exists between the door skin and the door surround structure.
(7) If the gaps are outside the above limits for the type I emergency exit door, adjust
the door vertically. Proceed to the next procedure.
D. Upper and Lower Door/Fuselage Skin Gaps Adjustment − The Type I Emergency Exit
Door Vertical Positioning
Refer to Figure 201 and Figure 206.
(1) Move the door to the "closed and locked" position and check the upper and lower
gaps between the door skin and the fuselage skin.
NOTE: Refer to Table 201 for the acceptable gaps.
(2) If the skin gaps do not meet the requirements stated in step (1) proceed as follows:
(refer to sheet 4).
(a) Remove the door and disconnect the push rod (G) from the upper torque tube
lever (J).
(b) Adjust the length of the push rod (G) to obtain the gaps detailed in step (1).
NOTE: To reduce the upper gap between the door and the fuselage skin,
shorten the push rod (G).
To reduce the lower gap between the door and the fuselage skin,
lengthen the push rod (G).
(c) Connect the push rod (G) to the lever (J). Do not install the new cotter pin at
this time.
(d) Install the door and check the upper and lower gaps between the door skin
and the fuselage skin.
(e) Do the steps (a) to (e) again as required until the acceptable gaps stated in
step (1) are achieved.
(f) Safety the bolt which attaches the push rod (G) to the lever (J) with a new
cotter pin.
E. Forward and Aft Door/Fuselage Side Gaps − Adjustment
Refer to Figure 201 and Figure 206.
(1) Move the door to the "closed and locked" position and make sure the door is
centered in the fuselage skin opening.
(2) Measure and record the forward and aft gaps between the door skin and the
fuselage skin.
NOTE: Refer to Table 201 for the acceptable gaps.
(3) If the gaps do not meet the requirements stated in step (2), remove the door (para.
2.A.).
(4) Modify the fuselage door skin opening to obtain the correct gaps.
F. Do a check of the door lateral positioning (Steps) as follows: (Refer to Figure 207, Sheet
1)
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 28 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 29

(1) Refer to the Table 202 for the skin steps between the outer surface of the door skin
and the fuselage skin. The table specifies two types of step requirements. They are
as follows:
(a) The steps for normal requirements. These steps are taken with the aircraft not
pressurized.
(b) The steps in discrepancy − acceptable limits, are taken with the aircraft
pressurized.
NOTE: If the steps for normal requirements for type I emergency exit door
are all within the specified limits, then it is not necessary to measure
the steps for discrepancy for the door.
(c) Both above skin step measurements are acceptable with the conditions that
follow:
1 Operate the door with the aircraft not pressurized to make sure that no
fouling occurs.
2 Make sure that the door is in the "Closed and Down" position.
3 Make sure that the door seal holds good contact with the door surround
structure.
4 Make sure that the door holds cabin pressure with the aircraft pressurized
(Refer to Para E of Chapter 21−30−00−02).
5 The door seal pressurization system operates correctly with the door
closed and aircraft pressurized.
(d) For steps in discrepancy − acceptable limits, make sure that the steps for all
other doors on the aircraft are within the nominal AMM requirements.
(e) Steps in discrepancy are measured and acceptable when the aircraft is
pressurized to a minimum of 2 PSI.
TABLE 202
EMERGENCY EXIT DOOR TYPE I LATERAL POSITIONING − STEPS
APPLICABLE AREA STEPS − NORMAL
REQUIREMENTS (Aircraft
not pressurized)
(Refer to Figure 207, (Sheet
1)
ACCEPTABLE LIMITS − STEPS
IN DISCREPANCY (Aircraft
pressurized)
(Refer to Figure 207, Sheet 2 and
3)
(Refer to Note 1 below)
Top edge + 0.090 to − 0.090 in. (+ 2.29
to − 2.29 mm)
(Refer to Notes 2, 3 and 4
below)
Max. 0.220 in. (5.59 mm)
(Refer to Notes 5, 6 and 7 below)
Bottom edge + 0.090 to − 0.090 in. (+ 2.29
to − 2.29 mm)
(Refer to Notes 2, 3 and 4
below)
Max. 0.220 in. (5.59 mm)
(Refer to Notes 5, 6 and 7 below)
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 29 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 30

TABLE 202
EMERGENCY EXIT DOOR TYPE I LATERAL POSITIONING − STEPS
Forward edge + 0.070 to − 0.090 in. (+ 1.78
to − 2.29 mm)
(Refer to Notes 2, 3 and 4
below)
Max. 0.090 in. (2.29 mm)
(Refer to Notes 5, 6 and 7 below)
Aft edge + 0.090 to − 0.070 in. (+ 2.29
to − 1.79 mm)
(Refer to Notes 2, 3 and 4
below)
Max. 0.220 in. (5.59 mm)
(Refer to Notes 5, 6 and 7 below)
NOTE: # 1. If the steps for normal requirements for the type I emergency exit door are all within
the specified limits, then it is not necessary to measure the steps for discrepancy for the
door.
NOTE: # 2. Make sure that the door is centered within the specified gaps before taking the step
measurements. If necessary, open and close the door to center the door in the opening.
NOTE: # 3. a). Make sure that the door is in the "Closed and Locked" position. b). Push the
door outboard until the pressure stops are in contact. Measure the steps while the
pressure stops are in contact.
NOTE: # 4. Measure the steps with the door centered at the same points as gaps.
NOTE: # 5. a). Make sure that all other step conditions for the type I emergency exit door are
within current AMM requirements. b). All other fuselage doors on the aircraft (i.e.
passenger (airstair) door, baggage door, service door, type III emergency exits etc.,)
have steps that are within current AMM requirements.
NOTE: # 6. a). Forward facing step − Discrepancy allowed 20.0 in. (50.8 cm) between any two
points along the forward edge.
b). Aft Facing Step − Discrepancy allowed 20.0 in. (50.8 cm) between any two points
along the aft edge.
NOTE: # 7. Longitudinal Step (Streamwise) − Discrepancy allowed 26.0 in. (60.04 cm) between
any two points along the top edge or the bottom edge.
(2) If the steps are outside the above limits for the normal requirements for the type I
emergency exit door, adjust the door laterally. Proceed to the next procedure.
G. Skin Steps Adjustment − The Type I Emergency Exit Door Lateral Positioning
Refer to Figure 201 and Figure 207.
(1) Move the door to the "closed and locked" position.
(2) Push the door outboard from the inside until the pressure stops are in contact.
(3) Adjust the eight pressure stops (N) to lightly contact the corresponding stop faces to
achieve the appropriate skin steps. (refer to sheets 1, 5 and 6).
NOTE: Maximum allowable skin steps are as follows:
Fwd facing (into airflow) 0.070 in. (1.78 mm)
Aft facing (out of airflow) 0.090 in. (2.29 mm)
Longitudinal (along airflow) − bottom and top edge: + 0.090 to − 0.090 in.
(+ 2.29 to − 2.29 mm).
(4) Release the outward pressure on the door.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 30 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 31

(5) Make sure that the door moves inward 0.040 in (1.02 mm) maximum.
(6) If necessary, adjust the position of the cams (AB), (AC) and (AD) to obtain the
dimensions required in steps (3) and (5). (refer to sheets 1 and 6).
NOTE: Cams are mounted on serrated plates. For adjustment purposes one
serration equals 0.031 in. (0.79 mm).
(7) Safety the pressure stops (N) with lockwire.
H. Proximity Sensor − Rigging
Refer to Figure 201, sheet 7.
(1) Remove the door from the aircraft (para. 2.A.).
(2) Using simulated roller (0.687 in. diameter) depress the target to the maximum
position by locating the roller at the bottom of cam and hold.
(3) Using the adjustment nuts (T) position the proximity sensor to obtain 0.010 to 0.020
in. gap (0.25 to 0.51mm).
(4) Install the door and move to the "closed and locked" position.
(5) Apply pressure to the inside face of the door until the pressure stops contact the
face of targets.
(6) Make sure the gap between the proximity sensor and the target is 0.010 to 0.070 in.
(0.25 to 1.78 mm).
(7) If adjustment is required to achieve 0.010 to 0.070 in. (0.25 to 1.78 mm) maximum
gap, proceed as follows:
(a) Remove the door from the aircraft (para. 2.A.).
(b) Adjust the position of the latch cam (AC) outward on the serrated plate to
achieve the dimension required to produce the permissible gap as stated in
step (6).
NOTE: One serration on serrated plate equals 0.031 in. (0.79 mm).
(8) If necessary do the steps (2) to (7) again to achieve the dimension required to
produce the permissible gap as stated in step (6).
(9) Safety the adjustment nuts (T) with lockwire to maintain gap.
I. Do a pull/push force check on the internal door handle as follows:
Refer to Figure 201, sheet 3.
(1) Install the forward emergency exit door (Refer to paragraph 2.B).
(2) Attach the force gauge to the internal door handle.
(3) Pull the internal door handle to the unlocked position.
(4) Make sure that the pull force (F1) necessary to move the internal door handle to the
unlocked position is less than 40 lbf (177.92 N).
(5) Push the internal door handle to the locked position.
(6) Make sure that the push force (F2) necessary to move the internal door handle to
the locked position is less than 40 lbf (177.92 N).
NOTE: When the bearings installed on lever assemblies, center and lower shaft
are replaced, make sure to apply the corrosion inhibiter compound and
the grease to these bearings.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 31 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 32

A
dam03_5220162_013.dg, gv/gw, feb4/2010
A
Make sure that the door is centred before taking the measurements.
If necessary, open and close the door to centre the door in the opening.
Push the door outboard until the pressure stops are in contact.  Measure the
gaps while the pressure stops are in contact.
Measurements are to be taken at the adjustable pressure stop (4 places).
NOTES
UPPER GAP
2
3
47
8
9
LOWER GAP
10 1
6 5
LEGEND  
1 10 Measuring locations.
Adjustable pressure stop.
EDGE GAPAFT EDGE GAP
APPROX.
DISTANCE
1
2
MID−
POINT
TOP STOP
BOTTOM
STOP
BOTTOM
STOP
TOP STOP
FORWARD
VIEW LOOKING INBOARD
0.030 in. (0.76 mm)
MINIMUM
0.030 in. (0.76 mm)
MINIMUM
0.030 in. (0.76 mm)
MINIMUM
0.030 in. (0.76 mm)
MINIMUM
Clearance of minimum 0.030 in. (0.76 mm) is permissible for upper and lower edges
provided that the sum of each respective pair (upper and lower measurement locations)
the door skin and door surround structure.
Clearance of minimum 0.030 in. (0.76 mm) is permissible for forward and aft edges provided
that the sum of each respective pair (forward and aft measurement locations) of clearance
does not exceed 0.210 in. (5.33 mm). Make sure no fouling exists between the door skin
and door surround structure.
of clearance does not exceed 0.375 in. (9.52 mm). Make sure no fouling exists between
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
EMERGENCY EXIT DOOR TYPE I VERTICAL POSITIONING − GAPS − ADJUSTMENT
Figure 206
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 32 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 33

A
dam03_5220162_012.dg, gv, 18/02/04
TOP EDGE
+0.090 to − 0.090 in.
(+2.29 to − 2.29 mm)
BOTTOM EDGE
+ 0.090 to − 0.090 in.
(+ 2.29 to − 2.29 mm)
TYPE I
DOOR
FUSELAGE
FORWARD EDGE
+ 0.070 to − 0.090 in.
(+ 1.78 to − 2.29 mm)
AFT EDGE
+ 0.090 to − 0.070 in.
(+ 2.29 to − 1.78 mm)
DISTANCE WITH THE DOOR
PUSHED OUT (AFT AND FWD)
DISTANCE WITH THE DOOR
PUSHED OUT (LOWER AND UPPER)
TYPE I
DOOR
FUSELAGE
A
Make sure that the door is centred before taking the measurements.
If necessary, open and close the door to centre the door in the opening.
Push the door outboard until the pressure stops are in contact.  Measure the
steps while the pressure stops are in contact.
Forward facing (into airflow): 0.070 in. (1.78 mm).
Aft facing (out of airflow): 0.090 in. (2.29 mm).
Longitudinal (along airflow) − bottom and top edge: + 0.090 to − 0.090 in. (+ 2.29 to − 2.29 mm).
NOTES
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
EMERGENCY EXIT DOOR TYPE I LATERAL POSITIONING − STEPS − ADJUSTMENT
Figure 207 (Sheet 1 of 3)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 33 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 34

dam03_5220162_014.dg, gv, 18/02/04
TYPE I  DOOR
SURROUND
(ACCEPTABLE LIMITS − STEPS IN DISCREPANCY)
MAX. 26.0 in.
(66.04 cm)TOP EDGE
AFT
EDGE FORWARD
EDGE
VIEW LOOKING INBOARD
MAX. 20.0 in.
(50.8 cm)
MAX. 20.0 in.
(50.8 cm)
TYPE I
DOOR
MAX. 26.0 in.
(66.04 cm) BOTTOMEDGE
Before taking the skin step measurements, make sure no fouling exists
between the door skin and the door surround with the aircraft not pressurized.
The skin step measurements noted here are with the aircraft pressurized and are acceptable
provided the following conditions are satisfied:
within current AMM limits.
2. All other fuselage doors on the aircraft (i.e. airstair door, baggage door, service door,
type III emergency exits etc.,) have steps that are within current AMM requirements.
Forward Edge −  20.0 in. (50.8 cm) between any two points along JH.
Aft Edge −  20.0 in. (50.8 cm) between any two points along KL.
Top Edge −  26.0 in. (66.04 cm) between any two points along HL.
Bottom Edge −  26.0 in. (66.04 cm) between any two points along JK.
NOTES
1. Make sure that all other step conditions for the Emergency Exit Type I door are
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
EMERGENCY EXIT DOOR TYPE I LATERAL POSITIONING − STEPS − ADJUSTMENT
Figure 207 (Sheet 2 of 3)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 34 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 35

dam03_5220162_015.dg, gv, 20/02/04
TYPE I
DOOR
MAX. 0.090 in.
(2.29 mm)
AFT STEP
STEPS WITH THE AIRCRAFT 
PRESSURIZED (AFT)
TYPE I
DOOR
FORWARD STEP
STEPS WITH THE AIRCRAFT 
PRESSURIZED (FWD)
MAX. 0.220 in.
(5.59 mm)
FUSELAGE
TYPE I
DOOR
MAX. 0.220 in.
(5.59 mm)
STEPS WITH THE AIRCRAFT 
PRESSURIZED (LOWER)
(LONGITUDINAL STEP)
STEPS WITH THE AIRCRAFT 
PRESSURIZED (UPPER)
(LONGITUDINAL STEP)
TYPE I
DOOR
FUSELAGE
MAX. 0.220 in.
(5.59 mm)
AIRFLOW
AIRFLOW
AIRFLOW
AIRFLOW
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
EMERGENCY EXIT DOOR TYPE I LATERAL POSITIONING − STEPS − ADJUSTMENT
Figure 207 (Sheet 3 of 3)
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 35 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 36

4. Inspection/Check
A. Fits and Clearances
TABLE 203
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I − FITS
AND CLEARANCES
IDENTIFICATION DESIGN LIMITS SERVICE (WEAR) LIMITS
FIG/
ITEM DESCRIPTION DIM. DIMENSION
CLEARANCE
(−SIGN
DENOTES
INTERFERENCE)
DIMENSION CLEARANCE
MIN MAX MIN MAX MIN MAX MAX
202/1 LEVER ID 0.3139 0.3149
0.0003 0.0023
0.3159
0.0035202/2 BUSHING OD 0.3126 0.3136 0.3116
202/1 LEVER ID 0.1895 0.1905
0.0 0.002
0.1915
0.003202/3 BOLT OD 0.1885 0.1895 0.1875
202/4 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.0025202/3 BOLT OD 0.1885 0.1895 0.1875
202/2 BUSHING ID 0.190 0.1915
0.0005 0.003
0.1925
0.004202/3 BOLT OD 0.1885 0.1895 0.1875
202/1 LEVER ID 0.8128 0.8135
0.0003 0.0015
0.8145
0.003202/5 BEARING[2][3] OD 0.8120 0.8125 0.8110
202/5 BEARING ID 0.3120 0.3125
0.0 0.0015
0.3135
0.003202/6 BOLT OD 0.3110 0.3120 0.3100
202/7 HOUSING ID 0.4389 0.4399
0.0003 0.0018
0.4410
0.003202/8 BUSHING OD 0.4381 0.4386 0.4370
202/8 BUSHING ID 0.3125 0.3140
0.0005 0.003
0.3150
0.004202/6 BOLT OD 0.3110 0.3120 0.3100
202/9 LEVER ID 0.3141 0.3151
0.0005 0.0025
0.3161
0.0035202/10 BUSHING OD 0.3126 0.3136 0.3116
202/9 LEVER ID 0.1895 0.1905
0.0 0.002
0.1915
0.003202/11 BOLT OD 0.1885 0.1895 0.1875
202/10 BUSHING ID 0.190 0.1915
0.0005 0.003
0.1925
0.004202/11 BOLT OD 0.1885 0.1895 0.1875
202/12 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.003202/11 BOLT OD 0.1885 0.1895 0.1875
202/9 LEVER ID 0.8128 0.8135
0.0003 0.0015
0.8145
0.003202/13 BEARING[2][3] OD 0.8120 0.8125 0.8110
202/13 BEARING ID 0.3120 0.3125
0.0 0.0015
0.3135
0.003202/14 BOLT OD 0.3110 0.3120 0.3100
202/20 HOUSING ID 0.4389 0.4399
0.0003 0.0018
0.4410
0.003202/15 BUSHING OD 0.4381 0.4386 0.4370
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 36 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 37

TABLE 203
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I − FITS
AND CLEARANCES
IDENTIFICATION DESIGN LIMITS SERVICE (WEAR) LIMITS
FIG/
ITEM DESCRIPTION DIM. DIMENSION
CLEARANCE
(−SIGN
DENOTES
INTERFERENCE)
DIMENSION CLEARANCE
MIN MAX MIN MAX MIN MAX MAX
202/15 BUSHING ID 0.3125 0.3140
0.0005 0.003
0.3150
0.004202/14 BOLT OD 0.3110 0.3120 0.3100
202/16 LATCH ID 0.3139 0.3149
0.0003 0.0023
0.3160
0.0035202/17 BUSHING OD 0.3126 0.3136 0.3116
202/16 LATCH ID 0.1895 0.1905
0.0 0.002
0.1915
0.003202/18 BOLT OD 0.1885 0.1895 0.1875
202/19 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.0025202/18 BOLT OD 0.1885 0.1895 0.1875
202/17 BUSHING ID 0.190 0.1915
0.0005 0.002
0.1925
0.003202/18 BOLT OD 0.1885 0.1895 0.1875
203/1 LEVER ID 0.3139 0.3149
0.0003 0.0023
0.3159
0.0035203/2 BUSHING OD 0.3126 0.3136 0.3116
203/1 LEVER ID 0.1895 0.1905
0.0 0.002
0.1915
0.003203/3 BOLT OD 0.1885 0.1895 0.1875
203/2 BUSHING ID 0.190 0.1915
0.0005 0.003
0.1925
0.004203/3 BOLT OD 0.1885 0.1895 0.1875
203/4 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.0025203/3 BOLT OD 0.1885 0.1895 0.1875
203/1 LEVER ID 0.9378 0.9393
0.0003 0.0023
0.9403
0.0035203/5 BEARING[2][3] OD 0.9370 0.9375 0.9360
203/5 BEARING ID 0.3120 0.3125
0.0 0.0015
0.3135
0.0025203/6 BOLT OD 0.3110 0.3120 0.3100
203/1 LEVER ID 0.3120 0.3130
0.0 0.0025
0.3140
0.0035203/7 CAM [4] OD 0.3105 0.3120 0.3095
203/8 LEVER ID 0.3139 0.3149
0.0003 0.0023
0.3159
0.0035203/9 BUSHING OD 0.3126 0.3136 0.3116
203/8 LEVER ID 0.1895 0.1905
0.0 0.002
0.1915
0.003203/10 BOLT OD 0.1885 0.1895 0.1875
203/9 BUSHING ID 0.190 0.1915
0.0005 0.003
0.1925
0.004203/10 BOLT OD 0.1885 0.1895 0.1875
203/11 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.0025203/10 BOLT OD 0.1885 0.1895 0.1875
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 37 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 38

TABLE 203
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I − FITS
AND CLEARANCES
IDENTIFICATION DESIGN LIMITS SERVICE (WEAR) LIMITS
FIG/
ITEM DESCRIPTION DIM. DIMENSION
CLEARANCE
(−SIGN
DENOTES
INTERFERENCE)
DIMENSION CLEARANCE
MIN MAX MIN MAX MIN MAX MAX
203/8 LEVER ID 0.9378 0.9393
0.0003 0.0023
0.9403
0.0035203/12 BEARING[2][3] OD 0.9370 0.9375 0.9360
203/12 BEARING ID 0.3120 0.3125
0.0 0.0015
0.3135
0.0025203/6 BOLT OD 0.3110 0.3120 0.3100
203/8 LEVER ID 0.3120 0.3130
0.0 0.0025
0.3140
0.0035203/13 CAM [4] OD 0.3105 0.3120 0.3095
203/14 HOUSING ID O.4389 0.4399
0.0003 0.0018
0.4410
0.0035203/15 BUSHING OD 0.4381 0.4386 0.4370
203/15 BUSHING ID 0.3125 0.3140
0.0005 0.003
0.3150
0.004203/6 BOLT OD 0.3110 0.3120 0.3100
204/1 SHAFT ID 0.3139 0.3149
0.0003 0.0023
0.3159
0.0035204/3 BUSHING OD 0.3126 0.3136 0.3116
204/3 BUSHING ID 0.1900 0.1915
0.0 0.003
0.1925
0.004204/2 BOLT OD 0.1885 0.1895 0.1875
204/1 SHAFT ID 0.1895 0.1905
0.0 0.002
0.1915
0.003204/2 BOLT OD 0.1885 0.1895 0.1875
204/4 ROD END[1] ID 0.1895 0.1900
0.0 0.0015
0.1910
0.0025204/2 BOLT OD 0.1885 0.1895 0.1875
204/5 CRANK ID 0.2500 0.2510
0.0 0.0025
0.2520
0.0035204/6 CAM [4] OD 0.2485 0.2500 0.2475
204/7 BEARING[4] ID 0.7493 0.7507
0.0 0.0024
0.7517
0.0040204/5 CRANK OD 0.7483 0.7493 0.7473
204/8 BEARING[4] ID 0.6250 0.6257
0.0007 0.0024
0.6267
0.0040204/5 CRANK OD 0.6233 0.6243 0.6223
204/9 HOUSING ID I.1878 1.1885
0.0003 0.0020
1.1895
0.0040204/7 BEARING[2][4] OD I.1865 1.1875 1.1855
204/22 HOUSING ID 1.0628 1.0635
0.0003 0.002
1.0645
0.003204/21 BEARING[2][4] OD 1.0615 1.0625 1.0605
204/1 SHAFT[5] ID 0.1895 0.1905
0.0 0.002
0.1915
0.010204/10 BOLT OD 0.1885 0.1895 0.1875
204/23 SHAFT[5] ID 0.1895 0.1905
0.0 0.002
0.1915
0.010204/24 BOLT OD 0.1885 0.1895 0.1875
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 38 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 39

TABLE 203
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I − FITS
AND CLEARANCES
IDENTIFICATION DESIGN LIMITS SERVICE (WEAR) LIMITS
FIG/
ITEM DESCRIPTION DIM. DIMENSION
CLEARANCE
(−SIGN
DENOTES
INTERFERENCE)
DIMENSION CLEARANCE
MIN MAX MIN MAX MIN MAX MAX
204/15 LEVER[5] ID 0.1895 0.1905
0.0 0.002
0.1915
0.010204/16 BOLT[5] OD 0.1885 0.1895 0.1875
204/17 BEARING[4] ID 0.7493 0.7507
0.0 0.0024
0.7517
0.0040204/18 CRANK OD 0.7483 0.7493 0.7473
204/21 BEARING[4] ID O.6250 0.6257
0.0007 0.0024
0.6267
0.0040204/18 CRANK OD 0.6233 0.6243 0.6223
204/18 CRANK ID 0.1900 0.1910
0.0 0.0025
0.1920
0.0035204/19 CAM OD 0.1885 0.190 0.1875
204/15 LEVER[5] ID 0.1895 0.1905
0.0 0.0020
0.1915
0.010204/20 BOLT OD 0.1885 0.1895 0.1875
204/1 SHAFT ID 0.3139 0.3149
0.0014 0.0034
0.3159
0.0045204/11 BUSHING OD 0.3126 0.3136 0.3105
204/11 BUSHING ID 0.190 0.1915
0.0005 0.003
0.1925
0.0040204/12 BOLT OD 0.1885 0.1895 0.1875
204/13 PIVOT ID 0.256 0.263
0.007 0.017
0.265
0.019204/14 EYEBOLT OD 0.246 0.249 0.244
204/14 EYEBOLT ID 0.190 0.192
0.0005 0.0035
0.193
0.0045204/12 BOLT OD 0.1885 0.1895 0.1875
204/14 EYEBOLT ID 0.190 0.192
0.0005 0.0035
0.193
0.0045204/25 BOLT OD 0.1885 0.1895 0.1875
205/1 PLATE ID 0.4389 0.4399
0.0003 0.0018
0.440
0.003205/2 BUSHING OD 0.4381 0.4386 0.4371
205/1 PLATE ID 0.3120 0.3130
0.0 0.002
0.3140
0.003205/3 BOLT OD 0.3110 0.3120 0.3100
205/4 BRACKET ID 0.190 0.194 0.004 0.010 0.195 0.0115
205/5 PIN OD 0.184 0.186 0.183
205/6 BRACKET ID 0.190 0.194
0.004 0.010
0.195
0.0115205/5 PIN OD 0.184 0.186 0.183
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 39 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 40

TABLE 203
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I − FITS
AND CLEARANCES
IDENTIFICATION DESIGN LIMITS SERVICE (WEAR) LIMITS
FIG/
ITEM DESCRIPTION DIM. DIMENSION
CLEARANCE
(−SIGN
DENOTES
INTERFERENCE)
DIMENSION CLEARANCE
MIN MAX MIN MAX MIN MAX MAX
205/4 BRACKET ID 0.190 0.194
0.0005 0.0055
0.196
0.0070205/7 BOLT OD 0.1885 0.1895 0.1875
NOTE: [1] Wear limit is 0.006 inch max. radial play.
[2] Install with Loctite GRADE AA. Refer to Chapter 20, STANDARD
PRACTICES − AIRFRAME.
[3] Wear limit is 0.001 inch max. radial play.
[4] Wear limit is 0.0018 inch max. radial play.
[5] The max. clearance quoted is the total elongation or out of roundness of the
hole.
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 40 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 41 (OCR)

de HAVILLAND
TEMPORARY  DASH8  TEMPORARY
REVISION  REVISION
Series 300
AIRCRAFT MAINTENANCE MANUAL
Doog
16
13
20  15  / (2 PLACES)  10
11
(2 PLACES)  12
(2 PLACES)  - 0-0-
C
18  17  19
B
DOOR MECHANISM INSTALLATION - FORWARD EMERGENCY EXIT DOOR TYPE I FITS
AND CLEARANCES
Figure 208
MASTER  Page 41 of 44
EFFECTIVITY: See First Page of TR# 52-042  52-20-16  Apr 10/2018
TR# 52-042

### Page 42

dam03_5220162_009.cgm, nn, apr04/2018
6
15
14
1
5
4
2
3
10 9
11
8
12
7
13
DSERIES 300
AIRCRAFT MAINTENANCE MANUAL
DOOR MECHANISM INSTALLATION − FORWARD EMERGENCY EXIT DOOR TYPE I FITS
AND CLEARANCES
Figure 209
MASTER
EFFECTIVITY: See First Page of TR# 52−042 52−20−16
Page 42 of 44
Apr 10/2018
TR# 52−042
TEMPORARY
REVISION
TEMPORARY
REVISION
Series 300

### Page 43 (OCR)

de HAVILLAND
TEMPORARY  DASH8  TEMPORARY
REVISION  REVISION
Series 300
AIRCRAFT MAINTENANCE MANUAL
15
16
25  19
.10
13
DOOR MECHANISM INSTALLATION - FORWARD EMERGENCY EXIT DOOR TYPE I FITS
AND CLEARANCES
Figure 210
MASTER  Page 43 of 44
EFFECTIVITY: See First Page of TR# 52-042  52-20-16  Apr 10/2018
TR# 52-042

### Page 44 (OCR)

de HAVILLAND
TEMPORARY  DASH8  TEMPORARY
REVISION  REVISION
Series 300
AIRCRAFT MAINTENANCE MANUAL
000 0.00001
PULL
DOOR MECHANISM INSTALLATION - FORWARD EMERGENCY EXIT DOOR TYPE I FITS
AND CLEARANCES
Figure 211
MASTER  Page 44 of 44
EFFECTIVITY: See First Page of TR# 52-042  52-20—16 Apr 10/2018
TR# 52-042

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
