# Britten-Norman Service Bulletin BN-2/SB: No revision named

- Rights: © Britten-Norman. Filed by the FAA in regulations.gov docket FAA-2010-1255; AD 2011-05-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Britten-Norman Service Bulletin BN-2/SB](https://openairdocs.org/service-documents/britten-norman/bn2-sb.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 5
- PDF: https://openairdocs.org/files/sha256/be/f7/bef790eda8dfaac69fc2aee17432b5d781e81eb7d296a35e21030ad9721d880f
- Page: https://openairdocs.org/service-documents/britten-norman/bn2-sb/file/bef790eda8df

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

B-  N  SERVICE
AIRCRAFT  BULLETIN
Britten-Norman Aircraft Limited.
BEMBRIDGE, Isle of Wight, United Kingdom PO35 5PR
Models Affected  Service Bulletin number
All BN2A, BN2B and BN2T series Islander aircraft.  BN-2/SB 313
Issue 3 - 24/02/2009
Elevator Tip Assemblies - Inspection
Reason for Change
This Service Bulletin has been revised to Issue 3 to clarify inspection procedures and to add a
terminating action.
1  Compliance Statement
Britten-Norman Aircraft Limited highly recommends that all operators and maintenance
organizations comply with this Service Bulletin.
Do the inspection procedure of this Service Bulletin at the earliest opportunity after receipt of this
Service Bulletin, or at the next daily check (check A).
2  Introduction
An event has been reported to Britten-Norman Aircraft Limited where the profiles of the elevator tip
assemblies (NB 31-235) have changed.
The outboard three inches of the elevator tip assembly profiles (top and bottom surfaces) have
changed from being convex profiles to concave profiles.
WARNING
The glass reinforced plastic (GRP) elevator tip assemblies may delaminate. This could have
a serious effect on the aircraft handling.
3  Applicability
This Service Bulletin is applicable to all BN 2A, BN 2B and BN 2T series Islander aircraft.
4  Weight and Balance
None.
24/02/2009  BN-2/SB 313
Issue 3  Page 1 of 5

### Page 2 (OCR)

Service Bulletin
5  Effect on Publications
The aircraft publications will be amended as necessary by normal revision action at the earliest
opportunity.
6  Action
Carry out an inspection of the left and right elevator tip assemblies (top and bottom surfaces) to
ascertain whether the profile has changed.
6.1  Inspection
1  Refer to Fig 1 and Fig 2.
2  Examine the outboard three inches of the elevator tip assemblies (left and right).
Ensure that the profiles of the top and bottom surfaces of the elevator tip assemblies do not
show signs of concavity (refer to section 9.2).
Figure 1 - Elevator Tip Assemblies
BN-2/SB 313  24/02/2009
Page 2 of 5  Issue 3

### Page 3 (OCR)

Service Bulletin
6.2  Failures
Please report the extent of any findings to the Head of Structural Engineering at Britten-Norman
Aircraft Limited, who will then advise as to the acceptability of the aircraft continuing in service, by:
Post:  Britten-Norman Aircraft Limited, Bembridge Airport, Isle of Wight. PO35 5PR
United Kingdom
Telephone: +44 (0) 20 3371 4000
Facsimile: +44 (0) 20 3371 4001
E-mail:  structural@bnaircraft.com
7  Manpower
This Service Bulletin can be completed in approximately one man-hour.
8  Provisioning
For more information, contact the Customer Support Department at B-N Group Limited, by:
• Post:  B-N Group Limited, Bembridge Airport, Isle of Wight. PO35 5PR
United Kingdom
Telephone: +44 (0) 20 3371 4000
Facsimile:  +44 (0) 20 3371 4001
E-mail:  into@britten-norman.com
9  Follow-on Action
9.1  No Concavity
No further action required.
9.2  Concavity
1  Confirm the degree of concavity (depth of depression below straight line) to Head of
Structural Engineering, refer 6.2.
2  The immediate action on finding concavity is to check for delamination. If ultrasonic
test gear is available this may be used otherwise a simple coin 'tap' test will suffice.
In the event of any delamination being detected the aircraft should be grounded until
the tip(s) are replaced.
4  Provided no delamination is detected then the aircraft is safe to return to service. The
concavity and delamination checks should be repeated periodically - every 50 flying
hours - until the tip(s) are replaced. However, the elevator tip(s) must be replaced
within 6 months from the issue date of this Service Bulletin 313 at Issue 3.
Note. If delamination found during the 50 hour checks, the aircraft should be grounded
until the elevator tip(s) are replaced.
24/02/2009  BN-2/SB 313
Issue 3  Page 3 of 5

### Page 4 (OCR)

Service Bulletin
Check for Concavity
Refer to Para 9.2
Concavity  No  Return to service.  No further
found?  inspections required
Yes
Check for Delamination
A/C returned to service with
50 hour checks until elevator
Delamination  No  tip replaced. The elevator tip
found?  must be replaced within
six months from date of
Yes,  Service Bulletin 313 (Issue 3).
A/C grounded until elevator
tip replaced
Return to service.
No further
inspections required
PC-A-573000-A-U0625-00008-A-01-1
Figure 2 - Inspection Flow Chart
BN-2/SB 313  24/02/2009
Page 4 of 5  Issue 3

### Page 5 (OCR)

Service Bulletin
10  Approval
The technical content of this document is approved under the authority of DOA number EASA.
21J. 138.
Signed.  D. Shan  D.Shon
Date  24 fel 2009
24/02/2009  BN-2/SB 313
Issue 3  Page 5 of 5

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
