# Britten-Norman Service Bulletin 364: Revision 3

- Rights: © Britten-Norman. Filed by the FAA in regulations.gov docket FAA-2021-0502; AD 2021-18-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Britten-Norman Service Bulletin 364](https://openairdocs.org/service-documents/britten-norman/sb-364.md)
- Title as filed: SB 0364_03-Rudder Final Drive 2T
- Pages: 7
- PDF: https://openairdocs.org/files/sha256/e4/0f/e40fcd059adc78da8671ab9b3a5738185dd927ea88971f90885b07b10b2f9b9f
- Page: https://openairdocs.org/service-documents/britten-norman/sb-364/file/e40fcd059adc

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SERVICE 
BULLETIN 
Britten-Norman Aircraft Limited 
Commodore House, Mountbatten Business Centre, Millbrook Road East,  
Southampton, SO15 1HY United Kingdom  
23/05/2018 SB 364 
Issue 3 Page 1 of 7 
Models Affected Service Bulletin Number 
All BN2T Series Britten-Norman Islander Aircraft (not including the BN2T 
-4S). 
 
SB 364 
Issue 3 – 23/05/2018 
INSPECTION OF THE RUDDER FINAL DRIVE ROD ASSEMBLY 
This is a highly recommended safety related Service Bulletin. 
1 COMPLIANCE STATEMENT 
Compliance is required within the next 200 flying hours. Refer to MS4 for inspection criteria. 
The closing action to this Service Bulletin will be an update to the Aircraft Maintenance Manual MM4 Chapter 
2.6. Any Rudder Final Drive Rod assembly that has evidence or record that it has previously had taper pins 
replaced or reworked, must be replaced within 200 flight hours of receipt of this Service Bulletin. 
2 INTRODUCTION 
Britten-Norman Aircraft has been made aware of instances of failures of the Rudder Final Drive Rod part 
number NB-45-0991.These failures have been observed on the region of  the taper pins.  There is evidence 
that supports the fact that replacing the taper pins, in accordance with the Maintenance Manual, could be a 
significant factor contributing to the failure of this rod .  This Service Bulletin introduces actions to be taken on 
finding loose taper pins or end  connections in the rudder final drive rod during routine inspection or in the 
event that there is evidence or record that taper pins have been previously replaced,  following the issue of 
this Service Bulletin. 
This SB is ONLY applicable to the Rudder Final Drive Rod.

### Page 2

Service Bulletin 
 
SB 364 23/05/2018 
Page 2 of 7 Issue 3 
3 APPLICABILITY 
This Service Bulletin is applicable to all BN2T Series Britten-Norman Islander aircraft not including the BN2T-
4S. 
4 EFFECT ON WEIGHT AND BALANCE 
None. 
5 EFFECT ON PUBLICATIONS 
The aircraft publications will be amended as necessary by normal revision action at the earliest opportunity.  
6 ACTION 
Operators are requested to examine  the Rudder Final Drive Rod assembly in accordance with M aintenance 
Schedule MS4 section 1 page 4 & 5 paragraph ‘C’ Control System Components. 
If considered unserviceable following this inspection, defects must be remedied immediately. 
Previously operators finding loose taper pins or end connections in the rudder final drive rod have been  able 
to replace the taper pins in accordance with the Aircraft Maintenance Manual Chapter 1.6 paragraph 41. This 
maintenance activity will no longer be supported by Britten-Norman Aircraft and instead the operator will now 
be required to replace the complete rudder drive rod assembly. 
In addition any Rudder Final Drive Rod assembly that has evidence or record that it has previously had taper 
pins replaced or reworked, must also be replaced within 100 flight hours of receipt of this Service Bulletin. 
 
 
 If the Rod Assembly is unserviceable the following procedure should be used to carry out replacement: 
 
7 REMOVAL AND INSTALLATION INSTRUCTIONS FOR UNSERVICEABLE UNITS 
7.1 Preparation 
 
1. Put the rear fuselage trestle in position at STA 352.45. Increase the height of the trestle until it 
touches the fuselage. 
2. Put warning signs in the flight compartment and adjacent to the aircraft to tel l persons ‘DO NOT 
OPERATE THE FLIGHT CONTROLS’. 
3. Put the maintenance platform in position to get access to the Rudder final control drive rod. 
4. Put the Rudder in the neutral position and install the Rudder gustlocks as required. 
5. Remove the applicable access panels to gain access to the Rudder final control rod. 
 
CAUTION: DO NOT STAND ON THE HORIZONTAL STABILISER

### Page 3

Service Bulletin 
 
23/05/2018 SB 364 
Issue 3 Page 3 of 7 
7.2 Removal 
 
1. Refer to Figure 1. 
2. Remove and discard the split pin (1). 
3. Remove and retain the slotted nut (2) and washer (3). 
4. Hold the Rudder final control drive rod (11) and remove and retain the bolt (4) and the two spacers 
(5). Lower the screwed end eye cleat from the Rudder drive lever. 
5. Remove and discard the split pin (6). 
6. Remove and retain the slotted nut (7) and washer (8). 
7. Hold the Rudder final control drive rod (11) and remove and retain the bolt (10) and the two 
spacers (9). 
8. Move the fork end from the Rudder drive lever. 
9. Remove the Rudder final control drive rod (11) from the aircraft. 
 
Inspect attaching parts retained (items 2 to 5 and 7 to 10 of figure 1); any items that are 
unserviceable, (show signs of damage or corrosion) must be replaced before installation. 
Refer to the Illustrated Parts Catalogue to identify part numbers. 
 
7.3 Installation 
 
1. Refer to Figure 1 
2. Align the fork end of the Rudder final control drive rod (11) with the forward Rudder drive lever. 
3. Hold the Rudder final control drive rod (11) in position and install the two spacers (9) and the bolt 
(10). 
4. Install the washer (8) and the slotted nut (7). 
5. Install a new split pin (6). 
6. Align the screwed end eye of the Rudder final control drive rod (11) with the aft Rudder drive lever. 
7. Hold the Rudder final control drive rod (11) in position and install the two spacers (5) and bolt (4).  
8. Install the washer (3) and the slotted nut (2). 
9. Install a new split pin (1). 
10. Lubricate the Rudder final control drive rod/Rudder drive lever in accordance with the Aircraft 
maintenance Manual. 
11. Remove the Rudder gustlocks as required. 
12. Do a Rudder control system rigging check, refer to chapter 2.6, maintenance chart 6. 
13. Install the removed access panels. 
14. Remove the warning signs, ‘DO NOT OPERATE THE FLIGHT CONTROLS’, from the flight 
compartment and adjacent to the aircraft. 
15. Remove the maintenance platform 
16. Remove the trestle and profile board.

### Page 4 (OCR)

Service Bulletin
STA 378.95
Figure 1
SB 364  23/05/2018
Page 4 of 7  Issue 3

### Page 5

Service Bulletin 
 
23/05/2018 SB 364 
Issue 3 Page 5 of 7 
8 MANPOWER 
This procedure will take between 2 and 8 hours to complete. 
9 PROVISIONING 
Please order Rudder Final Drive Rod Assembly NB -45-0991, available from Britten-Norman Ltd. Customer 
Services Department, at Britten -Norman Group Ltd. Bembridge Airport, Isle of Wight, PO35 5PR, United 
Kingdom. 
10 FOLLOW ON ACTION 
At a period not exceeding 1000 flight hours from initial inspection and after every 1000 flight hours following, 
operators are requested to examine the Rudder Final Drive Rod assembly in accordance with Maintenance 
Schedule MS1 section 1 page 4 & 5 paragraph ‘C’ Control System Components.  
Operators are requested to complete the operator feedback form at Appendix A and return it to Britten -
Norman Customer Support.  
This procedure will be entered into the Maintenance Schedule by normal revision action at the  earliest 
opportunity. 
 
For Customer Support  
e-mail - customer.support @britten-norman.com  
or  
telephone +44 (0) 203 371 4000 
 
11 APPROVAL 
The technical content of this document is approved under the authority of DOA n umber EASA.21J.138.

### Page 6

Service Bulletin 
 
SB 364 23/05/2018 
Page 6 of 7 Issue 3 
12 APPENDIX A – OPERATOR FEEDBACK 
OPERATOR DETAILS 
Company 
Name 
 
Contact 
Person 
 
Contact 
address 
 
 
 
Telephone 
Number 
 
Email Address  
AIRCRAFT DETAILS 
Model/Type  
Registration 
Number 
 
Constructor 
Number 
 
Total flying 
Hours 
 
Total landings

### Page 7

Service Bulletin 
 
23/05/2018 SB 364 
Issue 3 Page 7 of 7 
Please record below the details of the Rudder Final Drive Assembly currently fitted to the aircraft listed on 
page 6 of this appendix and list any repairs previously carried out. A separate form should be filled out for 
each aircraft owned by the operator. 
 NB-45-991 Rudder Final Drive Assembly 
HOURS IN SERVICE  
CYCLES IN SERVICE  
 TAPER PINS EYE END BEARING ASSEMBLY 
First repair (hours)   
First repair (cycles)   
Second repair (hours)   
Second repair (cycles)   
Third repair (hours)   
Third repair (cycles)   
   
   
   
   
Detail in this section any other relevant information:

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
