# CASA Service Bulletin 235-26-0006

Copy: No revision named ("SB 235-26-0006"), 40 pages: PDF https://openairdocs.org/files/sha256/63/01/6301b993055649dbe4d42f6f6ca5c8df99998ff3dd082f4b801aae86859bced9; text https://openairdocs.org/service-documents/casa/sb-235-26-0006/file/6301b9930556.md. Rights: © CASA. Filed by the FAA in regulations.gov docket FAA-2015-4809; AD 2016-07-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [CASA](https://openairdocs.org/service-documents/casa.md)
- Type: Service bulletin (Service Bulletin)
- Number: 235-26-0006
- Page: https://openairdocs.org/service-documents/casa/sb-235-26-0006

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-07-18](https://openairdocs.org/ad/2016-07-18.md), effective May 16, 2016: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/casa/sb-235-26-0006/proposed.md).

## Text (40 pages)

Rights: © CASA. Filed by the FAA in regulations.gov docket FAA-2015-4809; AD 2016-07-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
FIRE PROTECTION
ENGINE FIRE EXTINGUISHING. MODIFICATION OF THE ENGINE FIRE DETECTION SYSTEM.
1. GENERAL INFORMATION
A.  EFFECTIVITY
(1) Models
CN- 235-200, CN-235-300.
(2) Aircraft
The Version/MSN relationship is provided for information only.
This relationship is correct at the time of issue in accordance
with the information available in EADS-CASA. Any future changes
that are a result of the transfer of an aircraft from one version
to another will not be reflected in this list unless the Service
Bulletin is revised for another reason.
VERSION  MSN  KIT No.
AEOI  C-135.  SB235260006K01
AE02  C-139, C-143,  SB235260006K01
C-145.
IB02  C-018, C-030.  SB235260006K01
L302  C-130.  SB235260006K01
L303  C-172, C-186.  SB235260006K01
QCO2  C-042.  SB235260006K01
SMOI  C-161. C-169, S8235260006K01
(3) Spares
None
B .  CONCURRENT REQUIREMENTS
None
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 1 of 38

### Page 2 (OCR)

EADS
_ CASA
CN-235 - SERVICE BULLETIN
C. REASON
(1) HISTORY
The possibility that a false alarm occurs because of damp in the
connectors of the fire detectors has been found.
(2) OBJETIVE / ACTION
To modify the location and routing of the fire detection system.
(3) ADVANTAGES
To prevent false alarm and damp in the connectors of the fire
detectors.
(4) OPERATIONAL/MAINTENANCE CONSEQUENCE
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to:
- Put the aircraft in the safe condition for maintenance tasks.
- Put the access platform in position.
- Get access to the work area.
- Disconnect the fire detection sensors.
- Remove clamps and supports.
- Remove labels.
- Modify firewall.
- Install new clamps and supports.
- Connect the fire detection sensor.
- Set new labels.
- Do tests.
- Install the access panels.
- Record the accomplishment.
COMPLIANCE
(1) Classification
Recommended
(2) Accomplishment Timescale
None
F. APPROVAL
The technical content of this document has been approved by the
authority of the DOA No. EASA.21J.032.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 2

### Page 3 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
NOTE: This issue is a translation of SB-235-26-0006.  In case of any
disagreement, reference should be made to the Spanish Original issue,
which has been approved by the authority of the DOA No. EASA.21J. 032.
G.  MANPOWER
The manpower estimates given in this Service Bulletin are based on the
direct labour cost to do the work. These estimates assume that the
work will be done by experienced personnel, and may need to be revised
upwards to suit operators' circumstances.  The estimates do not
include the time to prepare, plan or inspect the work. Manufacture
and procurement of part and tools, curing times (drying times for
paints, sealants, adhesives, etc.)  and general administration work
are also not included.
Kit SB235260006K01
ON AIRCRAFT:  24
TOTAL MANHOURS :  24
ELAPSED TIME(HRS) :
NOTE: The indicated time is an approximated time for the
accomplishment of the modification described in Service
Bulletin.
H. WEIGHT AND BALANCE
(1) Variationof the Standard Basic Empty Weight (SBEW).
Kit SB235260006K01:  Weight = + 0.27 Kg.
(2) Variation of the momentum with respect to the reference plane.
Kit SB235260006K01:  Momentum = + 2.64 Kg m.
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
Aircraft Maintenance Manual (AMM):  06-41-54, 20-15-00, 20-21-00,
20-27-00, 20-28-00, 20-38-00,
20-50-00, 26-11-00, 26-11-11,
71-10-12, 71-10-13, 71-11-12
Illustrated Tools and Equipment  20-00-01, 26-11-02
Manual (ITEM):
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 3

### Page 4 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
K. PUBLICATIONS AFFECTED
Aircraft Maintenance Manual (AMM):  26-11-00, 26-11-11
Illustrated Parts Catalog (IPC):  26-11-00, 71-21-20
L. INTERCHANGEABILITY/MIXABILITY
Not applicable
M. RELATED FIGURES
- Figure 1 Modification of the firewall.
- Figure 2 Installation of support in the firewall.
- Figure 3 Modification of the fire detection sensor.
- Figure 4 Placement of labels.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 4

### Page 5 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
2. MATERIAL INFORMATION
A. MATERIAL - PRICE AND AVAILABILITY
(1) Material
Operators with aircraft shown in the effectivity of this Service
Bulletin should send a purchase order to EADS-CASA. Quote the
number of the Service Bulletin. The address is:
EADS- CASA
SERVICES - MATERIAL SUPPORT
Avda. de Aragón, 404
28022 MADRID
SPAIN
Fax:  +34 91 585 55 05
(2) Price and Availability
Sales terms must be agreed between the Operator and EADS-CASA in
accordance with the established procedure.
B.  INDUSTRY SUPPORT INFORMATION
None
C. LIST OF COMPONENTS
SB235260006K01
FIG ITEM N/P NEW  QTY  UM  KEYWORD ITEM N/P OLD INT INST DISP
1  MS20995C32  2,0  M1 Lockwir
2  35-75402-0301  2  Label
3  35-75402-0601  2  Label
8  NAS1149C0332R  2  Washer
9  MS21043-3  2  Nut
11  NAS1096-3-8  4  Screw
16  35-75428-0101  support
18  37731-301  12  Washer
21  AS21919WCJ28  Clamp
40  LN9178-3208F  20  Rivet
51  MS21913J6  2  plug
52  AS5178J06  2  Nut
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 5

### Page 6 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
FIG ITEM N/P NEW  QTY UM KEYWORD ITEM N/P OLD  INT INST DISP
53  NAS1149C0932R 4  Washer
D. LIST OF MATERIALS - OPERATOR SUPPLIED
(1) Consumable Materials
DESCRIPTION  REFERENCE TO CML  QTY PER A/C INST DISP
MAT NO.
Epoxy Adhesive  Mat. No. Z-15.237 As required
Silicone Adhesion Promoter  Mat. No. Z-15.904 As required
Fire-Wall Sealant  Mat. No. Z-16.206 As required
Silicone Sealant  Mat. No. Z-16.306 As required
Fluorosilicone Sealant  Mat. No. Z-16.403 As required
Fluorocarbon Sealant  Mat. No. Z-16.421 As required
Sealant  Mat.  NO.  AIMS-04- As required
05-014B/-015B
Tape  Mat. No. Z-22.172 As required
Solvent  Mat. No. Z-23.139 As required
Self-Adhering Insulation Tape Mat. No. Z-22.127 As required
Lint-Free Cotton Cloths  Mat. No. Z-24.930 As required
NOTE: To accomplish this Service Bulletin it is also necessary to use
the consumable materials listed in the referenced procedures.
(2) Components
None
E. PARTS TO BE RE-IDENTIFIED BY THE OPERATOR
Effectivity: All, except QC02.
ITEM N/P NEW  KEYWORD  ITEM  N/P OLD  INT  INST DISP
(61) 35-A3825-0101  Front  (60)  35-52151-0109  03  Modify
firewall
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 6

### Page 7 (OCR)

EADS '
CASA
_ CN-235 - SERVICE BULLETIN
ITEM  N/P NEW  KEYWORD  ITEM  N/P OLD  INT  INST DISP
(63)  35-A3825-0201  Rear  (62)  35-52151-0207  03  Modify
firewall
NOTE : INT 03 - Not Interchangeable.
Effectivity: QCO2.
ITEM N/P NEW  KEYWORD  ITEM  N/P OLD  INT  INST DISP
(61)  35-A3728-0101  Front  (60)  35-52151-0105  03  Modify
firewall
(63)  35-A3729-0101  Rear  (62)  35-52151-0205  03  Modify
firewall
NOTE: INT 03 - Not Interchangeable.
F. TOOLING - PRICE AND AVAILABILITY
None
G. SPECIAL TOOLS
None
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 7

### Page 8 (OCR)

EADS  CASA
CN-235 - SERVICE BULLETIN
INTENTIONALLY LEFT BLANK
Date: Jul 08/2014  SB - 235-26-0006
Original  Pag : 8

### Page 9 (OCR)

EADS
CASA
CN-235 - SERVICE BULLETIN
3. ACCOMPLISHMENT INSTRUCTIONS
WARNING: Make sure all warning indications are respected in the reference
procedures.
WARNING: Mo Isure that you obey all the safety precautions of the amn
A. GENERAL
(1) Preparation
NOTE: All the dimensions shown herein are in millimeters, unless
otherwise specified.
(a) Disconnect all the electrical power supplies and make sure
that all the corresponding electrical circuits are isolated.
(b) Prepare the aircraft for the tasks and obey all the safety
precautions.
(c) Put warning notices in the correct positions to prevent
unwanted operation of any control or system.
(d) Get access to the aircraft and find the area where the
Service Bulletin will be applied.
(e) Prepare the consumable material necessary to do the work.
(2) Standard Practices
(a) Standard Torques (AMM 20-21-00).
(b) Sealing (AMM 20-38-00).
(c) Surface Treatment (AMM 20-50-00).
(d) Electrical Items (AMM 20-15-00).
(e) Electrical Wiring and Bundles (AMM 20-27-00).
(f) Electrical Bonding (AMM 20-28-00).
(3) Work Breakdown
On aircraft:
- Put the aircraft in the safe condition for maintenance tasks.
- Put the access platform in position.
- Get access to the work area.
- Disconnect the fire detection sensors.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 9

### Page 10 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
Remove clamps and supports.
Remove labels.
- Modify firewall.
Install new clamps and supports.
- Connect the fire detection sensor.
- Set new labels.
- Do tests.
- Install the access panels.
- Record the accomplishment.
B. MODIFICATION
NOTE: The item numbers referred to in this paragraph correspond to
those given in the kit and to the different illustrations.
NOTE: The procedure for the left powerplant is described. The
procedure for the right powerplant is symmetrical.
NOTE: The FIN numbers shown between parenthesis refer to the right
powerplant.
(1) Preliminary operations
(a) Put the access platform under the left powerplant.
(b) Remove and keep the access panels:
- 413AR (423AR) .
- 413AL (423AL).
- 413AT (423AT) .
- 414AT (424AT).
Refer to AMM 06-41-54, AMM 71-10-12, AMM 71-11-12 and AMM
71-10-13.
NOTE: Remove the panel 413AB (423AB) only when the removal
of the bottom fire sensor set is necessary.
Refer to AMM 71-10-12.
(c) Do the preliminary operations described in AMM 26-11-11.
(2) Removal
NOTE: Keep the items that you removed before in storage bags to
install them later.
(a)  Disconnect the top fire detection sensor (100).
Refer to Figure 3 Sheet 4.
1 At the end of the support (12):
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 10

### Page 11 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
Remove and discard the lockwire (1).
- Disconnect the connector (30) from the receptacle (29).
- Remove and discard the washer (18) from the connector
- Put a protective cover/plug on the connector (30) and
the receptacle (29).
(b) Disconnect the bottom fire detection sensor (110).
Refer to Figure 3 Sheet 7.
1 Both ends of the support (13):
- Remove and discard the lockwire (1).
- Disconnect the connector (33) from the flanged coupling
- Disconnect the connector (36) from the flanged coupling
(37).
- Remove and discard the 2 washers (18) from the
connectors (33) and (36).
- Put a protective cover/plug on the connectors (33) and
(36) and on the flanged couplings (17) and (37).
(c) Disconnect the end wire of the fire detection system (120).
1 At the end of the firewall set (50):
Refer to Figure 3 Sheet 2.
- Remove and discard the lockwire (1).
- Disconnect the connector (34) from the receptacle (4).
- Remove and discard the washer (18) from the connector
(34).
- Put a protective cover/plug on the connector (34) and
the receptacle (4).
- Remove and keep the washer (5).
- Remove and keep the coupler (4).
2 At the end of the support (13):
Refer to Figure 3 Sheet 7.
- Remove and discard the lockwire (1).
- Disconnect the connector (27) from the flanged coupling
(17) .
- Remove and discard the washer (18) from the connector
(27) .
- Put a protective cover/plug on the connector (27) and
the flanged coupling (17).
(d) Disconnect the end wire of the fire detection system (130).
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 11

### Page 12 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
1 At the end of the support (12):
Refer to Figure 3 Sheet 4.
- Remove the receptacle (29) from the clamp (10).
2 At the end of the support (13):
Refer to Figure 3 Sheet 7.
Remove and discard the lockwire (1).
- Disconnect the connector (28) from the flanged coupling
(37).
- Remove and discard the washer (18) from the connector
(28).
- Put a protective cover/plug on the connector (28) and
the flanged coupling (37).
3 Disconnect and keep the end wire of the fire detection
system (130).
Refer to Figure 3 Sheet 7.
(e)  Remove and keep the support (12), installed on the firewall
set (50).
Refer to Figure 3 Sheet 4.
Remove and keep:
- 1 clamp (6).
- 1 washer (8).
- 1 clamp (10).
- 1 screw (11).
- 1 grounding terminal (19).
Remove and discard the 2 rivets (40) that connect to the
firewall set (50).
Remove and discard the 6 rivets (40) that connect from the
flanged couplings (17) and (37) to the support (13). Remove
and keep the flanged couplings (17) and (37).  Remove and
discard the support (13) of the bottom cowling (22) of the
engine. Refer to Figure 3 Sheet 5.
(g)  Remove and keep the support (25) of the bottom cowling (22)
of the engine. Refer to Figure 3 Sheet 7.
(h)  At the 2 clamp sets (21) of the side bar of the engine
support.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 12

### Page 13 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
Refer to Figure 3 Sheet 6.
Remove and keep:
- 2 washers (8).
- 2 nuts (9).
- 2 screws (11).
- 2 clamps (14).
- 2 sleeves (15).
- 2 clamps (21).
(i) At the clamp set (35) of the front vertical bar of the
engine support.
Refer to Figure 3 Sheet 3.
Remove and keep:
- 1 clamp (6).
- 1 screw (7).
- 1 washer (8).
- 1 nut (9).
- 1 clamp (14).
- 1 sleeve (15).
- 1 clamp (35).
(j) EFFECTIVITY: A11, except QCO2.
At the 2 clamp sets (35) of the front horizontal bar of the
engine support.
Refer to Figure 3 Sheet 2 and Figure 3 Sheet 3.
Remove and keep:
- 2 washers (8).  неоне (9).
- 2 nuts (9).
- 2 clamps (14).
- 2 sleeves (15).
- 2 clamps (35).
(k) EFFECTIVITY: QCO2.
At the 2 clamp sets (35) of the front horizontal bar of the
engine support.
Refer to Figure 3 Sheet 2 and Figure 3 Sheet 3.
Remove and keep:
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 13

### Page 14 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
- 2 clamps (6).
- 2 screws (7).
- 2 washers (8).
- 2 nuts (9).
- 2 clamps (14).
- 2 sleeves (15).
- 2 clamps (35).
Remove and discard the 2 spacers (26).
(1)  Remove and discard the labels (2) and (3). Refer to Figure
(3) Preparation for the installation.
WARNING: Take care when you use material Z-23.139. Obey the
manufacturer's instructions strictly.
WARNING: Take care when you use material Z-15.904. Obey the
manufacturer's instructions strictly.
WARNING: Take care when you use material Z-16.403. Obey the
manufacturer's instructions strictly.
WARNING: Take care when you use material Z-16.421. Obey the
manufacturer's instructions strictly.
WARNING: Take care when you use material AIMS-04-05-014B/-015B.
Obey the manufacturer's instructions strictly.
WARNING: Do not use solvents or aerosols that contain lubricants
and other residues that can decompose at high
temperatures and cause the system to deteriorate.
Make a drill hole in the firewall set (50) in the new
location. Refer to the measurements given in Detail B of
Figure 1.
Refer to AMM 20-50-00.
(b) Clean all the supports of the top (100) and bottom (110)
fire detection sensors and the adjacent area.
(c) Clean all the supports of the end wires of the fire
detection sensors (120) and (130) and the adjacent area.
(d)  Examine all the supports of the top (100) and bottom (110)
fire detection sensors for damage, dirt and corrosion.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 14

### Page 15 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
(e) Examine all the supports of the end wires of the fire
detection system (120) and (130) for damage, dirt and
corrosion.
(f) After the removal of the support (12), fill the holes left
by the 2 rivets (40) with 2 new rivets (40).
Refer to Figure 2.
(g) Put the  support (12) that you kept before on the firewall
set (50). Refer to the measurements given in Figure 2.
(h) Transfer the drill holes from the support (12) to the
firewall set (50) at the diameter given in Figure 2. Refer
to AMM 20-50-00.
(i) Put the flanged couplings (17) and (37) on the new support
(16). Refer to Figure 3 Sheet 5.
Transfer the drill holes from the flanged couplings (17) and
(37) to the support (16) at the diameter given in Figure 3
Sheet 5.
(k) Install the flanged couplings (17) and (37) on the support
(16) with 6 rivets (40).
(1) Clean the area around the triangular lugs of the flanged
couplings (17) and (37) with solvent Mat. No. Z-23.139.
(m) Seal the contour of the triangular lugs of the flanged
couplings (17) and (37) with sealant Mat. No. AIMS-04-05-
014B/-015B. Refer to AMM 20-38-00.
(n) Clean flanged couplings (17) and (37) internally as shown:
- Remove any dry contamination with a soft brush.
- Remove oil, grease or similar contamination with a soft
brush and moderately apply solvent Mat. No. Z-23.139.
- Leave the solvent to dry for a minimum of ten minutes
or blow with pressurized air or nitrogen.  (Do not use
pressure lines from the workshop because they are likely
to contain damp).
Apply silicone adhesion promoter Mat.  Z-15.904 in
the bottom cowling (22) of the engine in the areas where
supports (16) and (25) must be installed.
Refer to Figure 3 Sheet 5 and Figure 3 Sheet 8.
(4) Installation
Date: Jul 08/2014  SB - 235-26-0006
Original  Pag : 15

### Page 16 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
WARNING: Take care when you use material Z-15.237. Obey the
manufacturer's instructions strictly.
WARNING: Take care when you use material Z-16.421. Obey the
manufacturer's instructions strictly.
CAUTION: When connecting the connectors, make sure that all
the connectors and couplers are clean, dry and
undamaged.
NOTE: When you install fire detection sensors, prevent
unnecessary twists and kinks. Make sure the fire
detection sensors has a minimum curve radius of 25.4
(Refer to AMM 26-11-00).
Install the access panel 413AB (423AB) if it has been
removed. Refer to AMM 06-41-54 and AMM 71-10-12.
At the original position of the drill hole in the firewall
set (50).
Refer to Figure 3 Sheet 2.
Install:
- 2 new washers (53).
- 1 new plug (51).
- 1 new hexagonal nut (52).
NOTE: Apply sealant Mat.  Z-16.421 on the previous
set on the two sides of the firewall. Refer to AMM
20-38-00.
(c) At the position of the new drill hole in the firewall set
(50).
Refer to Figure 3 Sheet 3.
Install:
- 1 kept coupler (4).
- 1 kept washer (5).
(d) Install the support (12) on the firewall set (50).
Refer to Figure 3 Sheet 4.
Use the parts that follow:
- 1 kept clamp (6).
- 1 kept washer (8).
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 16

### Page 17 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
- 1 kept clamp (10).
1 kept screw (11).
- 1 kept grounding terminal (19). Refer to AMM 20-28-00.
- 2 new rivets (40).
NOTE : Wet install  rivets (40) with fire-wall sealant Mat.
No. Z-16.206.
With the flanged couplings (17) and (37) installed before,
install the new support (16), with epoxy adhesive Mat.
Z-15.237 on the bottom cowling (22) of the engine. Refer to
the measurements given in Figure 3 Sheet 5.
NOTE: Apply sealant Mat. No. Z-16.403 after you install
the support (16).
(f) Install the support (25) that you kept before in its new
position as shown in Figure 3 Sheet 8, with epoxy adhesive
Z-15.237 on the bottom cowling (22) of the
engine, with the following parts:
- 1 kept washer (8).
- 1 kept nut (9).
- 1 kept screw (11).
- 1 kept clamp (14).
- 1 kept sleeve (15).
NOTE: Apply sealant Mat. No. Z-16.403 after you install
the support (25).
(g)  Install the 2 clamps (21) that you kept before on the side
bar of the engine support.
Refer to Figure 3 Sheet 6.
Use the parts that follow on each clamp:
- 1 kept washer (8).
- 1 kept nut (9).
• set seve
NOTE: Make sure that you install each clamp (21) on the
side bar of the engine support in the direction given
in the illustration.
(h) Install 1 new clamp (21) on the front vertical bar of the
engine support.
Refer to Figure 3 Sheet 4.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 17

### Page 18 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
Use the parts that follow:
- 1 kept clamp (6).
- 1 kept screw (7).
- 1 new washer (8).
- 1 new nut (9).
- 1 kept clamp (14).
- 1 kept sleeve (15).
_ Install the clamp (35) that you kept before on the front
horizontal bar of the engine support.
Refer to Figure 3 Sheet 2.
Use the parts that follow:
- 1 kept washer (8).
- 1 kept nut (9).
- 1 new screw (11).
- 1 kept clamp (14).
- 1 kept sleeve (15).
(3)  Install the clamp (35) that you kept before on the front
horizontal bar of the engine support.
Refer to Figure 3 Sheet 3.
Use the parts that follow:
- 1 kept clamp (6).
- 1 kept screw (7).
- 1 kept washer (8).
- 1 kept nut (9).
- 1 kept clamp (14).
- 1 kept sleeve (15).
(k)  Install the clamp (35) that you kept before on the front
vertical bar of the engine support.
Refer to Figure 3 Sheet 3.
Use the parts that follow:
- 1 kept clamp (6).
- 1 kept washer (8).
- 1 kept nut (9).
- 1 new screw (11).
Connect the bottom fire detection sensor (110).
Refer to Figure 3 Sheet 8.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 18

### Page 19 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
1 Install the bottom fire detection sensor (110) on the
support (25) installed in its new position.
2 At both ends of the support (16):
- Remove the protective cover/plug from the connectors
(33) and (36) and from the flanged couplings (17) and
(37) .
- Install 1 new washer (18) on each connector (33) and
(36).
- Connect the connector (33) to the flanged coupling
(17). Refer to AMM 20-15-00.
- Connect the connector (36) to the flanged coupling
(37). Refer to AMM 20-15-00.
- Tighten the connectors (33) and (36) to a torque
between 9.0 Nm and 11.3 Nm.
- Safety the connectors (33) and (36) to the flanged
couplings (17) and (37) with new lockwire (1).
3 Set the bottom fire detection sensor (110) by tightening
the screws of all the clamps of its route to the standard
torque. Refer to AMM 20-21-00.
(m) Connect the end wire of the fire detection system (130).
1 At the end of the support (12):
Refer to Figure 3 Sheet 4.
- Install the receptacle (29) on the clamp (10).
2 At the end of the support (16):
Refer to Figure 3 Sheet 7.
- Remove the protective cover/plug from the connector
(28) and the flanged coupling (37).
- Install 1 new washer (18) on the connector (28).
- Connect the connector (28) to the flanged coupling
Refer to AMM 20-15-00.
- Tighten the connector (28) to a torque between 9.0 Nm
and 11.3 Nm.
- Safety the connector (28) to the flanged coupling (37)
with new lockwire (1).
3 Attach the end wire of the fire detection system (130) by
tightening the screws of all the clamps of its route to
the standard torque. Refer to AMM 20-21-00
(n)  Connect the top fire detection sensor (100).
Refer to Figure 3 Sheet 4.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 19

### Page 20 (OCR)

EADS '
CN-235 - SERVICE BULLETIN
1 Install the top fire detection sensor (100) on:
- The 2 clamps (21) of the side bar of the engine
support, installed in their new positions.
NOTE: Make sure that the route of the top fire
detection sensor (100) by the side bar of the
engine support is kept away from the inlet and
outlet of the starter generator (20).
- The clamp (35) of the front vertical bar of the engine
support.
- The new clamp (21) of the front vertical bar of the
engine support.
2 At the end of the support (12):
- Remove the protective cover/plug from the connector
(30) and the receptacle (29).
- Install 1 new washer (18) on the connector (30).
- Connect the connector (30) on the receptacle (29).
Refer to AMM 20-15-00.
- Tighten the connector (30) to a torque between 9.0 Nm
and 11.3 Nm.
- Safety the connector (30) to the receptacle (29) with
new lockwire (1).
3 Set the top fire detection sensor (100) by tightening the
screws of all the clamps of its route to the standard
torque. Refer to AMM 20-21-00
(o) Connect the end wire of the fire detection system (120).
Refer to Figure 3 Sheet 3.
1 Install the end wire of the fire detection system (120)
- The 2 clamps (35) of the front bar of the engine
support, installed in their new positions.
- The clamp (35) of the front vertical bar of the engine
support.
2 At the end of the firewall set (50):
- Remove the protective cover/plug from the connector
(34) and the coupler (4).
Install 1 new washer (18) on the connector (34).
- Install the washer (5) that you kept before.
- Connect the connector (34) to the coupler (4). Refer
to AMM 20-15-00.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 20

### Page 21 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
- Tighten the connector (34) to a torque between 9.0 Nm
and 11.3 Nm.
- Safety the connector (34) to the washer (5) with new
lockwire (1).
3 At the end of the support (16):
Refer to Figure 3 Sheet 8.
Remove the protective cover/plug from the connector
(27) and the flanged coupling (17).
• Install 1 new washer (18) on the connector (21)
- Connect the connector (27) of the flanged couplinc
(17). Refer to AMM 20-15-00.
- Tighten the connector (27) to a torque between 9.0 Nm
and 11.3 Nm.
- Safety the connector (27) to the flanged coupling (17)
with new lockwire (1).
4 Attach the end wire of the fire detection system (120) by
tightening the screws of all the clamps of its route to
the standard torque. Refer to AMM 20-21-00
(p) Apply silicone sealant Mat. No. Z-16.306 to the support
(16). Attach the connectors (27) and (28) of the end wires
of the fire detection system (120) and (130) to the support
(16) with self-adhering insulation tape Mat. No. Z-22.127.
Refer to Figure 3 Sheet 8.
NOTE: Do not cover the nut (24) with the self-adhering
insulation tape Mat. No. Z-22.127.
(q) Attach the negative terminal of the end wires of the
fire detection system (120) and (130) with tape Mat. No.
Z-22.172. Refer to Figure 3 Sheet 8.
(r)  Put the self-adhesive labels (2) and (3) in the new
positions given in Figure 4.
(s) Re-identify the modified parts (See section 2.E.).
C. IEST
NOTE: The tests that you must do on the left powerplant are described
here. The procedure is the same for the right powerplant.
(1) Preliminary isolation and continuity checks.
Refer to Figure 3.
Date: Jul 08/2014  SB - 235-26-0006
Original  Pag : 21

### Page 22 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
Disconnect the connectors (34) and (70) from their
receptacles (4) and (71).
NOTE: Install protective covers/plugs on the connectors and
receptacles to prevent contamination.
NOTE: Keep the protective covers/plugs until the parts are
installed again.
Connect the multimeter,  ITEM 20-00-01, between the pins A,
which correspond to the central contacts, of the receptacles
(4) and (71).
- The resistance must be between 62 and 110 ohms.
NOTE: If the result of the measurement is outside, but
near, the limit given, do an inspection to make sure
that the system is free of dirt or corrosion. If
the result is very far from the limit given, contact
Airbus Defence & Space.
(c)  Connect the isolation meter, ITEM 26-11-02, between pin B,
external, and pin A of the receptacle (4). Apply a tension
between 350VDC and 500VDC.
(d) If the resistance value is very high above the established
value of 20 megaohms, go to section 3.C. (4).
(e) Disconnect the multimeter, ITEM 20-00-01, and the isolation
meter, ITEM 26-11-02.
(2) Drying of the connectors.
Refer to Figure 3.
(a) Clean the area adjacent to the connectors (27), (28), (30),
(33) and (36) with cotton cloths Mat.  Z-24.930, or
with a brush and solvent Mat. No. Z-23.139.
Disconnect the connector (30) from the receptacle (29), the
connectors (28) and (36) from the flanged coupling (37) and
the connectors (27) and (33) from the flanged coupling (17).
(c) Install protective covers/plugs on the connectors and
couplers to prevent contamination.
NOTE: Keep the protective covers/plugs until the parts are
installed again.
(d) Remove and discard the washers (18).
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 22

### Page 23 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
(e) Clean with a brush and dry each connector and coupler with
a hot air dryer. Do not use the pressure lines from the
workplace.
NOTE: Make sure that the supports and attachment clamps
of the fire sensor are not damaged. Refer to AMM
26-11-11.
tools and equipment used. Refer to AMM 26-11-00.
(3)  Isolation and continuity checks.
Refer to Figure 3.
(a) Connect the isolation meter, ITEM 26-11-02, between:
- Pin A (central) and Pin B (external) of each connector
(27), (28), (30), (33) and (36).
- Pin A and Pin B of each flanged couplings (17) and (37)
and the receptacle (29).
- Apply tension between 350VDC and 500VDC and make sure that
the measurement that you get is higher than 20 megaohms
in each case.
WARNING: If any part shows values outside the limit, dry
the part again and do the isolation test again.
the value is still outside the limit, discard and
replace the part with a new one. Contact Airbus
Defence & Space.
Install 1 new washer (18) on each connector (27), (28),
(30), (33) and (36). Do not install two washers (18) on one
connector.
WARNING:  Make sure that the washer (18) is installed with
its flat side against the female side of the
connector.
(c) Remove the protective covers/plugs.
Connect the connectors (2/), (28), (30), (33) and (36) to
their flanged couplings (17), (29) and (37).
NOTE: Tighten the connectors to a torque between 9.0 Nm
and 11.3 Nm (79.64 Ibf and 100 1bf). Safety the
connectors with lockwire.
Do the isolation and continuity checks from section 3.C. (1)
again to check the wire harness fully.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 23

### Page 24 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
(f) Connect the connectors (34) and (70).
(4) Sealing procedure.
Refer to Figure 3.
(a) Make sure that the areas that you must seal are clean of
dirt or unwanted material.
(b) Covering procedure:
- The barrier layer must made up of a circling cover of the
connector.
- The thickness of the tape must be chosen in a way that
allows easy application.
- The application must overlap at least 51% between each
turn.
- The tightness of the belt during the covering process must
be limited to 5% of the total length of the belt.
- At the start and the end of the covering you must add 2
or 3 more turns.
- The speed and tension in the covering must not change
during this process.
- The area of covering must be from 5 cm on the shrinkable
sleeve to the nut of the connector. The nut must be
completely covered.
NOTE: Take special care when you remove all the sealant
that was there before, to prevent any damage to the
fire sensor system.
D. CLOSE UP
(1) Install the access panels that you kept before:
- 413AR (423AR).
- 413AL (423AL).
- 413AT (423AT).
- 414AT (424AT) .
Refer to AMM 06-41-54, AMM 71-10-12, AMM 71-11-12 and AMM
71-10-13.
(2) Remove the access platform.
(3) Remove the safety clips with tags and close the circuit breakers
that you opened before.
(4) Remove the warning notices from the cockpit.
(5) Make sure that the area below and around the aircraft is free of
items that block it.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 24

### Page 25 (OCR)

EADS '
AN CASA
CN-235 - SERVICE BULLETIN
(6) Remove all the tools and equipment from the work area. Make sure
that the work area is clean.
E. DOCUMENTATION
Write in the applicable aircraft records (Aircraft Modification Log
Book) that you have done all the work given in this Service Bulletin.
F.  FIGURES
See next page/s.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 25

### Page 26 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
INTENTIONALLY LEFT BLANK
Date: Jul 08/2014  SB- 235-26-0006
Original  Pag : 26

### Page 27 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
BEFORE 62
AFTER 63
50
BEFORE 60
AFTER 61
50
010.2
440
PROPELLER CENTERLINE  ENGINE CENTERLINE
C SB 260006 1 0100 00 00  TURBINE CENTERLINE
Figure 1. Modification of the firewall.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 27

### Page 28 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
B
C
50
BEFORE  AFTER
50  50
PROPELLER  CENTER  _INE
PROPELLER  •CENTERLINE
ENGINE CENTERLINE  ENGINE CENTERLINE  TURBINE CENTERLINE
TURBINE CENTERLINE
345
SB 260006 1 0200 00 00  DIAMETER
SYMBOL  ITEM  REMARKS
MIN.  MAX.  -50
•  40  3.25  3.40
RIVET HEAD ON HIDDEN SIDE.
WET INSTALL RIVETS (40) WITH FIRE-WALL
SEALANT MAT. No. Z-16.206.
TRANSFER THE DRILL HOLE FROM THE SUPPORT (12)  TO THE FIREWALL (50).  -12
FILL HOLES WITH RIVETS (40).
Figure 2. Installation of support in the firewall.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 28

### Page 29 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
B
969
PROPELLER  CENTERLINE
TURBINE CENTERLINE
TURBINE  CENTER
C SB 260006 1 0308 01 00  CENTERLINE  K
ENGINE
2370
Figure 3. Modification of the fire detection sensor.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 29

### Page 30 (OCR)

EADS '
• CASA
CN-235 - SERVICE BULLETIN
[DI
BEFORE
F→!
250 TO ENGINE CENTERLINE
E-E
BEFORE
100,  - 120
X=2370
- 5
- 18
AFTER  120
250 TO ENGINE CENTERLINE
50
E-E
100  AFTER
F-F  F-F
BEFORE  AFTER
- 35
C SB 260006 1 0308 02 00  14-  1> EFFECTIVITY: QCO2.  50
15
Figure 3. Modification of the fire detection sensor. (Sheet 2 of 8)
Date: Jul 08/2014  SB- 235-26-0006
Original  Pag : 30

### Page 31 (OCR)

EADS'
CASA
CN-235 - SERVICE BULLETIN
G  G
BEFORE  AFTER
+ X
H-
115
120-
100  100-
H→
ENGINE  CENTERLINE  ENGINE  CENTERLINE
H-H  H-H
BEFORE  AFTER  X-X
35  X=2370_
18
- 120
50
14-
J-J  15  J-J
BEFORE  AFTER
C SB 260006 1 0308 03 00  - 35
EFFECTIVITY: QCO2.
Figure 3. Modification of the fire detection sensor.  (Sheet 3 of 8)
Date:Jul 08/2014  SB-235-26-0006
Original  Pag : 31

### Page 32 (OCR)

EADS
CASA
CN-235 - SERVICE BULLETIN
K
BEFORE  AFTER
100-  - 120
120-
100 TO TURBINE CENTERLINE  130-  210 TO TURBINE CENTERLINE  N  40 TO TURBINE CENTERLINE
100
120
130
W
100
50
L-L  N-N
W  BEFORE  120
AFTER
C SB 260006 1 0308 04 00  10
• 12
- 130
L 50
8
40
Figure 3. Modification of the fire detection sensor. (Sheet 4 of 8)
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 32

### Page 33 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
M-M  M-M
BEFORE  AFTER
- 130
- 120
37
37
40 (6 PLACES)
AFTER
191.7  TO TURBINE  CENTERLINE
- 17<
DIAMETER
SYMBOL  ITEM  MIN.  MAX -  REMARKS
•  40  3.25  3.40  <3
RIVET HEAD ON VISIBLE SIDE.
WET INSTALL RIVETS (40) WITH FIRE-WALL
SEALANT MAT. No. Z-16.206.
TRANSFER THE DRILL HOLE FROM THE FLANGED-COUPLINGS (17) AND (37)
TO THE SUPPORT  (16).
APPLY SILICONE ADHESION PROMOTER 2-15.904.
APPLY EPOXY ADHESIVE Z-15.237.
APPLY SEALANT Z-16.403.
APPLY SEALANT AIMS 04-05-014B/-015B.
Figure 3.  Modification of the fire detection sensor. (Sheet 5 of 8)
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 33

### Page 34 (OCR)

EADS
CASA
CN-235 - SERVICE BULLETIN
BEFORE  KOKR
100-
-20
P
AFTER
-20
100-
210  178
Q-Q  R-R
10°
60  14
15
C SB 260006 1 0308 06 00  11
UPON FIRE DETECTOR (100) INSTALLATION ENSURE IT
IS KEPT AWAY FROM STARTER GENERATOR (20) INLET AND OUTLET.
Figure 3. Modification of the fire detection sensor. (Sheet 6 of 8)
Date: Jul 08/2014  SB - 235-26-0006
Original  Pag : 34

### Page 35 (OCR)

EADS '
CASA
_ CN-235 - SERVICE BULLETIN
S
130-  - 120
28  - 27
37  17
- 13
36  - 33
T→!
\110
25
→
- 22
T-1
11
- 110
25
C SB 260006 1 0308 07 00  BEFORE
Figure 3.  Modification of the fire detection sensor. (Sheet 7 of 8)
Date:Jul 08/2014  SB-235-26-0006
Original  Pag : 35

### Page 36 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
S
T-T
- 110
- 110<  25
25
145 TO X=2370
→
336 TO ENGINE
CENTERLINE
130  • 120
28-  • 27
18  18
• 24
C SB 260006 1 0308 08 00  APPLY ADHESION PROMOTER Z-15.904.  MINIMUN BENDING RADIUS R=25.4.
APPLY ADHESIVE EPOXY Z-15.237.  37 -  -18
APPLY SEALANT Z-16.403.  18
BAND THE INDICATED ZONE, OVERLAPING 50%  33
AT LEAST, WITH SELF-ADHERING INSULATION
TAPE  MAT. No. Z-22.127.  36
DO NOT COVER THE NUT (24).  110-  - 110
APPLY SILICONE SEALANT Z-16.306.
FIX THE FINAL END WITH TAPE Z-22.172.
AFTER
Figure 3. Modification of the fire detection sensor. (Sheet 8 of 8)
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 36

### Page 37 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
C
BEFORE
BEFORE
C
AFTER
AFTER
C SB 260006 1 0400 00 00  >2
> INSTALL LABEL ON HIDDEN SIDE.
Figure 4. Placement of labels.
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 37

### Page 38 (OCR)

EADS '
CASA
CN-235 - SERVICE BULLETIN
INTENTIONALLY LEFT BLANK
Date: Jul 08/2014  SB - 235-26-0006
Original  Pag : 38

### Page 39 (OCR)

EADS
CASA
CN-235 - SERVICE BULLETIN
FIRE PROTECTION
ENGINE FIRE EXTINGUISHING. MODIFICATION OF THE ENGINE FIRE DETECTION SYSTEM.
REPORTING SHEET
Please complete the appropriate item (A or B):
A - SB WILL BE embodied  YES/NO (if NO please
comment)
If YES, aircraft concerned (as per SB effectivity by default) and planned
dates (month/year) of embodiement:
B - SB HAS BEEN embodied on aircraft:
Operator comments:
From Airline:
Name/Title:
Signature:  Date:
If operational documentation is affected (see Paragraph 1.K of this
SB): If information is needed prior to next normal revision or prior to SB
embodiment, please indicate required service(s):
Either  Advance data  YES/NO
Or  Intermediate/Temporary revision  YES/NO
Important Information: This SB will only be incorporated in your maintenance
and operational documentation if this sheet is returned to EADS-CASA(MTAD)
and signed by a duly authorised representative. With the next feasible
revision, this will result in
updating of maintenance documentation to show pre and post SB data.
- updating of maintenance and operational documentation to show post SB
data after embodiment.
If this SB requires previous or simultaneous accomplishment of other SBs,
EADS-CASA(MTAD) shall automatically include them in the manual revisions.
Please return this completed sheet to:
AIRBUS MILITARY
ENGINEERING SUPPORT - SERVICE ENGINEERING
Autovia A-4, km 528,5. San Pablo North.
41020 Seville (Spain)
TEL: (34) 95 459 41 69
FAX: (34) 95 459 35 31
Date: Jul 08/2014  SB-235-26-0006
Original  Pag : 1 of 1

### Page 40

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
