# CFM International Service Bulletin 72-0564: Revision 3

- Rights: © CFM International. Filed by the FAA in regulations.gov docket FAA-2013-0407, the docket of AD 2013-26-01. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [CFM International Service Bulletin 72-0564](https://openairdocs.org/service-documents/cfm/sb-72-0564.md)
- Title as filed: U.S. DOT/FAA - CFM56-7B SB 72-0564
- Pages: 54
- PDF: https://openairdocs.org/files/sha256/b8/16/b81600a55871175c7f06415e3e9a719cdcd0bb185686ac7c1c458f8488f410a5
- Page: https://openairdocs.org/service-documents/cfm/sb-72-0564/file/b81600a55871

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

TRANSMITTAL SHEET
CFM INTERNATIONAL
CFM56-7B SERVICE BULLETIN 72-0564, REVISION 3
ENGINE - GENERAL (72-00-00) - INTRODUCTION OF A NEW ACCESSORY GEARBOX ASSEMBLY
(AGB) WITH A NEW STARTER DRIVE PAD AND REWORK OF THE OLD AGB TO THE NEW ONE
MAY 25, 2011
This page transmits Revision 3 to CFM56-7B Service Bulletin 72-0564 dated October 13, 2009, Revision 1
dated June 28, 2010 and Revision 2 dated November 16, 2010.
The revision 1 of this Service Bulletin has never been issued. This revision incorporates all the information
t h a tw a st ob ei nt h er e v i s i o n1 .
This revision has been revised to update the correct the Spare Code for bracket P/N 340-091-109-0 and
correct one tool number. Consequently, the following paragraph has been updated:
-2 . C .Con/g191guration Chart to update and add new Operation Codes.
-2 . E .Tooling - Price and Availability to correct 856A2969 tool number.
- 3. ACCOMPLISHMENT INSTRUCTIONS to correct 856A2969 tool number and clarify the jet /g192ow criteria
which was 2.89 US gal/h (70% of the /g192ow rate) and becomes 70% of the /g192ow rate.
The vertical dash in the left margin identi /g191es changes. Change, which does not affect technical content
may not be highlighted in the Transmittal Sheet.
This Service Bulletin is reissued in entirety.

### Page 2

(No text on this page.)

### Page 3

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
CFM PROPRIETARY INFORMATION
The information contained in this document is CFM proprietary information and is disclosed in
con/g191dence.It is the property of CFM and shall not be used,disclosed to others or reproduced
without the express written consent of CFM, including, but without limitation, it is not to be used in
the creation, manufacture, development, or derivation of any repairs, modi /g191cations, spare parts,
design,or con /g191guration changes or to obtain FAA or any other government or regulatory approval
to do so. If consent is given for reproduction in whole or in part,this notice and the notice set forth
on each page of this document shall appear in any such reproduction in whole or in part. The
information contained in this document may also be controlled by U.S. export control laws.
Unauthorized export or re-export is prohibited.
All technical documentation and information contained herein, with respect to assembly and
disassembly, cleaning, inspection methods and limits, repair methods and limits, operational
limits, life limits and the like, have been developed and approved for use with engines and parts
that have been manufactured and/or approved by CFM and that have been maintained in
accordance with CFM technical documentation and recommendations. CFM has no contractual
or legal obligation for, nor knowledge of, non-CFM-approved parts and repairs. Accordingly, this
document is not intended to apply to non-CFM-approved parts and repairs.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 1 of 52

### Page 4

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
1. PLANNING INFORMATION
A. Effectivity
CFM56-7B20, -7B22, -7B24, -7B26, -7B27
CFM56-7B22/B1, -7B24/B1, -7B26/B1, -7B27/B1, -7B27/B3
CFM56-7B26/B2
CFM56-7B20/3, -7B22/3, -7B24/3, -7B26/3, -7B27/3
CFM56-7B22/3B1, -7B24/3B1, -7B26/3B1, -7B27/3B1, -7B27/3B3
CFM56-7B26/3B2
CFM56-7B26/3F , -7B27/3F
CFM56-7B26/3B2F , -7B27/3B1F
CFM56-7B20/2, -7B22/2, -7B24/2, -7B26/2, -7B27/2
(1) The old Accessory Gearbox assembly (AGB) 340-046-505-0 and its old components
(Refer to paragraph 2.C. C ONFIGURATION CHART) installed on CFM56-7B engines
or stocked as spares are affected.
(2) The new Accessory Gearbox assembly 340-046-508-0 and its new components
(Refer to paragraph 2.C. C ONFIGURATION CHART)w i l lb ei n t r o d u c e di np r o d u c t i o n
on the engine serial numbers listed below:
For CFM56-7B/3 :
This information will be provided through a revision of this Service Bulletin.
For CFM56-7B and CFM56-7B/2 :
There is no CFM56-7B or CFM56-7B/2 engine model in the production line anymore.
B. Description
This Service Bulletin announces the production introduction and spare parts availability of
the following:
- A new Accessory Gearbox assembly 340-046-508-0 equipped with a new handcranking
line oil seal assy 340-155-304-0, a new handcranking cover assy 340-047-605-0, a new
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 2

### Page 5

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
starter drive pad assy 340-047-804-0 and a new spool 335-310-200-0. Refer to /g191gure
1, /g191gure 2 and /g191gure 3.
NOTE 1: For AGB 340-046-508-0, you must apply a bead of silicone elastomer sealant
RTV102 or RTV103 when you install the housing of the new oil seal assy
340-155-304-0 in its location on the AGB housing to insure its sealing.
- A new bracket assy 340-091-111-0 in accordance with the new con /g191guration of the starter
drive pad assy 340-047-804-0.
- For the details of new starter drive pad assy 340-047-804-0, refer to paragraph 2.C.
CONFIGURATION CHART and /g191gure 4.
- A new drain line 340-200-002-0 with its brackets 340-206-001-0, 340-199-801-0,
340-199-901-0 and its attaching parts to collect the leakage of the new oil seal and to drain
the handcranking sump. Refer to /g191gure 1, /g191gure 2 and /g191gure 9.
This Service Bulletin provides also the accomplishment instructions to rework and reidentify
the old AGB 340-046-505-0 to the new AGB 340-046-508-0.
NOTE 2: During the rework of the old AGB 340-046-505-0 to the new AGB
340-046-508-0, you do not have to install washers 649-341-031-0 in the new
brackets 340-206-001-0, 340-199-801-0 and 340-199-901-0 locations.
C. Compliance
Category 3
Do at next engine shop visit opportunity.
NOTE: This Service Bulletin can be accomplished in shop.
D. Concurrent Requirements
None.
E. Reason
(1) Objective:
INTRODUCTION OF NEW PARTS.
T o improve the reliability.
(2) Condition:
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 3

### Page 6

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
Some cases of engine oil loss have been reported and resulted in IFSD (In Flight
Shut Down).
(3) Cause:
Ground investigations showed that the AGB handcranking cover assy was not
installed or incorrectly installed.
(4) Improvement:
Modi/g191cation of the AGB by the introduction of a new oil seal assy on the new starter
drive pad assy and a new handcranking cover assy to prevent oil leakage from
handcranking pad.
This modi/g191cation is associated to the installation of a new drain line to collect possible
oil leakage of the oil seal assy and to drain the handcranking pad sump.
Sealing of the new oil seal assy by the application of a bead of silicone elastomer
sealant RTV102 or RTV103 on the mating surface between seal housing and AGB
housing.
(5) Substantiation:
Substantiation is by testing and comparative analysis.
F. Approval
The technical content of this document is approved by the FAA and under the authority of
DOA n° EASA.21J.086.
G. Manpower
Y ou will need approximately 4 man-hours to replace the old starter drive pad assy by the
new one on the AGB and to install the new brackets and the new drain line on the engine.
H. Weight and Balance
Accomplishment of this Service Bulletin will result in a weight increase of 1.467 lb (0,666 kg).
I. References
CFM56-7B Illustrated Parts Catalog, CFMI-TP .PC.14
CFM56-7B Engine Shop Manual, CFMI-TP .SM.10
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 4

### Page 7

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
CFM56 Standard Practices Manual, CFMI-TP .SP .2
CFM56 Consumable Products Manual, CFMI-TP .CP .3
CFM56 Illustrated T ool and Equipment Manual, CFMI-TP .TE.10
BOEING 737-600/700/800/900 Aircraft Maintenance Manual
NOTE: The reference documents listed below are for the engine manufacturer's internal
use only:
AAS: 27608 CAD: MOD063338
AAS: 27741 CAD: MOD107115
J. Publications Affected
CFM56-7B Illustrated Parts Catalog, CFMI-TP .PC.14, ATA 72-63-00
CFM56-7B Engine Shop Manual, CFMI-TP .SM.10, ATA 72-63-00
CFM56 Illustrated T ool and Equipment Manual, CFMI-TP .TE.10
BOEING 737-600/700/800/900 Aircraft Maintenance Manual
K. Interchangeability
The physical interchangeability of the AGB assembly is affected by the introduction of a
new starter drive pad assy with a new oil seal assy, a new drain line and new brackets
assemblies. The functional interchangeability of the AGB assembly is not affected.
The new starter drive pad assy with a new oil seal assy is interchangeable only as a set
with the old starter drive pad assy.
The new handcranking cover assy is not interchangeable with the old one.
The old and new parts can not be mixed.
L. Software Accomplishment Summary
None.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 5

### Page 8

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
2. MATERIAL INFORMATION
A. Material - Price and Availability
(1) Parts necessary to do this Service Bulletin:
Part Number
Qty/
Eng Part Name
Unit
$ Price
Pkg
Qty
Lead
Time
Days
333-089-182-000 (1) Logistic Kit 12,205.25 (1) Quote
. 335-310-200-0 (1) Spool 118.25 (1) 7
. 340-047-804-0 (1) Pad Assy- Starter
Drive
7914.00 (1) 10
. 340-047-605-0 (1) Cover Assy-
Handcranking
1199.00 (1) 7
. 340-155-304-0 (1) Seal Assy - Oil 2,974.00 (1) 30
649-393-163-0 (1) Preformed Packing
O-Ring
16.75 (10) 30
J221P163 (Alt) Preformed Packing
O-Ring
14.00 (10) 7
649-393-158-0 (1) Preformed Packing
O-Ring
12.25 (25) 30
J221P158 (Alt) Preformed Packing
O-Ring
7.00 (25) 5
649-393-154-0 (1) Preformed Packing
O-Ring
10.75 (25) 30
J221P154 (Alt) Preformed Packing
O-Ring
6.95 (25) 5
649-393-034-0 (1) Preformed Packing
O-Ring
2.45 (50) 30
J221P034 (Alt) Preformed Packing
O-Ring
1.85 (50) 5
649-393-137-0 (1) Preformed Packing
O-Ring
2.65 (50) 30
J221P137 (Alt) Preformed Packing
O-Ring
- (-) -
333-089-183-000 (1) Logistic Kit 2,198.15 (1) Quote
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 6

### Page 9

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
Part Number
Qty/
Eng Part Name
Unit
$ Price
Pkg
Qty
Lead
Time
Days
. AS3237-12 (3) Bolt-Mach Dbl Hex Hd 5.50 (50) 30
. AS3236-08 (2) Bolt-Mach Dbl Hex Hd 13.00 (-) 7
. 340-200-002-0 (1) Drain- Tube Assy 1071.00 (1) 30
. 340-091-111-0 (1) Bracket Assy 409.75 (1) 30
. 340-199-801-0 (1) Bracket Assy 197.60 (1) 30
. 340-199-901-0 (1) Bracket Assy 165.95 (1) 30
. 340-206-001-0 (1) Bracket Assy 159.15 (1) 30
. AS3236-12 (4) Bolt-Mach Dbl Hex Hd 4.70 (100) 30
. AS3237-08 (4) Bolt-Mach Dbl Hex Hd 4.60 (10) 30
. AS3486-10 (4) Nut 28.75 (1) 30
J1431P06 (4) Clamp 15.75 (40) 30
649-393-013-0 (2) Preformed Packing
O-Ring
0.65 (100) 30
J221P013 (Alt) Preformed Packing
O-Ring
0.57 (25) 10
NOTE 1: These kits 333-089-182-000 and 333-089-183-000 are added only to
facilitate the spare parts ordering process, but each part can be also
purchased separately.
NOTE 2: Prices can change.
(2) Other Spare Parts:
Part Number
Qty/
Eng Part Name
Unit
$ Price
Pkg
Qty
Lead
Time
Days
340-046-508-0 (1) Gearbox Assy -
Accessory
Quote (-) Quote
NOTE: Prices can change.
(3) Consumables:
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 7

### Page 10

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
Code Number Description
CP1039 Acetone
CP2101 Graphite Compound
CP2266 RTV102
Or RTV103
CP2442 Engine Oil
CP5069 Calibration Fluid
CP5070 Vaseline
B. Industry Support Information
Parts : CFM will provide a 50% back-end discount on the 2 logistic kits P/N 333-089-182-000
and 333-089-183-000. Refer to paragraph 2.A. Material – Price and Availability.
Labor : CFM will support the 4 manhours necessary to rework the old AGB P/N to the
new one.
All warranty claims for credit request on the 2 logistic kits and the labor must be submitted
within one year of compliance and by December 31, 2016. Send a Warranty Claim with the
number of this SB to CFM through your routine channel or to:
Europe, Middle East, and Africa Region
Customers
CFM SA Customers
CFM Customer Support Operation
Attn: Warranty and Guarantee Manager
c / oS n e c m a–S i t ed eM e l u n-M o n t e r e a u
Aerodrome de Villaroche – BP 1936
77019 Melun Cedex - France
T el: 33 (0) 1 64.14.85.72
Fax: 33 (0) 1 64.14.87.65
N o r t ha n dS o u t hA m e r i c aa n dA s i a
Customers
CFM Inc. Customers
CFM International Inc
Attn: Manager Warranty Administration
One Neumann Way – Room 444
Cincinnati, OH 45215-1988 USA
T el: 1 513 552 2000
Fax: 1 513 552 5081
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 8

### Page 11

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
C. Con/g191guration Chart
New Part Number
Qty/
Eng Part Name
Old
Part Number/
IPC Location
Qty/
Eng OP
Chg/
Sprt
Code
9324M60G01-G02-G03-
G04-G05-G06-G07-G08-
G09
(X) Engine Assy 9324M60G01-G02-G03-
G04-G05-G06-G07-G08-
G09
72-00-00-45-001
(X) RM -/-
1887M40G01-G02-G03-
G04-G05-G06-G07
(X) Engine Assy 1887M40G01-G02-G03-
G04-G05-G06-G07
72-00-00-45-002
(X) RM -/-
9324M60G10 (X) Engine Assy 9324M60G10
72-00-00-45-003
(X) RM -/-
9324M60G11 (X) Engine Assy 9324M60G11
72-00-00-45-004
(X) RM -/-
. 340-046-508-0 (1) Gearbox Assy -
Accessory
.340-046-505-0
72-00-00-45-710
72-63-00-05-001
72-63-00-20-001
(1) SU/
RW/
RI
1/A
.. 340-047-804-0 (1) Pad Assy - Drive
Starter
..340-047-802-0
72-63-00-05-320
see Note 4
(1) SU 5/A
... 340-047-904-0 (1) Pad - Drive Starter ...340-047-902-0
72-63-00-05-380
(1) SU 5/A
... J970P03 (4) Insert - Key Locked ...J970P03
72-63-00-05-370
(2) AD 5/E
- (-) Insert - Key Locked ...649-680-055-0 (Alt) DE 5/E
... J970P04 (8) Insert - Key Locked ...J970P04
72-63-00-05-330
(9) DE 5/E
- (-) Insert - Key Locked ...649-680-056-0 (Alt) DE 5/E
... 649-550-005-0 (1) Nozzle - Oil - (-) AD 5/-
... 340-152-101-0
see Note 4
(1) Plug - (-) AD 5/-
... J1037P06 (1) Nipple - (-) AD 5/-
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 9

### Page 12

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
New Part Number
Qty/
Eng Part Name
Old
Part Number/
IPC Location
Qty/
Eng OP
Chg/
Sprt
Code
... 649-393-012-0 (1) Packing-Preformed
O-Ring
- (-) AD 5/-
... J221P012 (Alt) Packing-Preformed
O-Ring
- (-) AD 5/-
... 340-155-801-0 (1) Pin-Centering - (-) AD 5/-
- (-) Packing-Preformed
O-Ring
..AS3085-134
72-63-00-05-190
(2) DE 5/-
- (-) Packing-Preformed
O-Ring
..M83248-1-134
72-63-00-05-190
(ALT) DE 5/-
.. 649-393-137-0 (1) Packing-Preformed
O-Ring
- (-) AD 5/-
.. J221P137 (Alt) Packing-Preformed
O-Ring
- (-) AD 5/-
.. 649-341-031-0 (3) Washer-Plain ..649-341-031-0
72-63-00-05-180
(4) DE 5/-
.. AS3237-12 (3) Bolt-Mach Dbl Hex Hd ..AS3237-12
72-63-00-05-170
(4) DE 5/-
.. 340-047-605-0 (1) Cover-Assy ..340-047-602-0
72-63-00-05-200
(1) SU 5/A
... 340-047-704-0
see Note 4
(1) Cover ...340-047-702-0
72-63-00-05-210
(1) SU 5/A
... 335-322-902-0
see Note 4
(1) Cable ...335-322-901-0
72-63-00-05-220
(1) SU 5/A
.. 340-155-304-0 (1) Oil Seal - Assy - (-) AD 5/-
... 340-196-401-0 (1) Packing-Preformed
O-Ring
- (-) AD 5/-
... 340-155-404-0 (1) Oil Seal - Subassy
Matched Parts
- (-) AD 5/-
.... 340-155-601-0 (1) Ring - Mating - (-) AD 5/-
.... 340-155-504-0 (1) Oil Seal - (-) AD 5/-
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 10

### Page 13

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
New Part Number
Qty/
Eng Part Name
Old
Part Number/
IPC Location
Qty/
Eng OP
Chg/
Sprt
Code
.. 649-393-034-0 (1) Packing-Preformed
O-Ring
- (-) AD 5/-
.. J221P034 (Alt) Packing-Preformed
O-Ring
- (-) AD 5/-
.. AS3236-08 (2) Bolt-Mach Dbl Hex
head
- (-) AD 5/-
.. 335-310-200-0 (1) Plug
(Old Name)
Spool
(New Name)
..340-052-901-0
72-63-00-20-250
(1) SU 5/E
- (-) Packing-Preformed
O-Ring
..J221P114
72-63-00-20-230
(1) DE 5/-
- (-) Packing-Preformed
O-Ring
..649-393-114-0 (Alt) DE 5/-
.. J221P013 (2) Packing-Preformed
O-Ring
..J221P013
72-63-00-20-240
(1) AD 5/-
.. 649-393-013-0 (Alt) Packing-Preformed
O-Ring
..649-393-013-0 (Alt) AD 5/-
. 340-091-111-0 (1) Bracket- Assy .340-091-109-0
72-00-00-41-120
(1) SU 5/D
. 340-200-002-0 (1) Drain- Tube Assy - (-) AD 5/-
. 340-206-001-0 (1) Bracket - (-) AD 5/-
. 340-199-801-0 (1) Bracket - (-) AD 5/-
. 340-199-901-0 (1) Bracket-Assy - (-) AD 5/-
. AS3236-12 (4) Bolt - Mach Dbl Hex
head
.AS3236-10
72-00-00-26-470
(4) SU 5/E
. AS3237-08 (4) Bolt - Mach Dbl Hex
head
- (-) AD 5/-
. AS3486-10 (4) Nut - (-) AD 5/-
. J1431P06 (4) Clamp - (-) AD 5/-
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 11

### Page 14

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
New Part Number
Qty/
Eng Part Name
Old
Part Number/
IPC Location
Qty/
Eng OP
Chg/
Sprt
Code
.. 649-341-031-0 (6) Washer-Plain ..649-341-031-0
72-63-00-05-271
(9) DE 5/-
.. 649-341-031-0 (2) Washer-Plain ..649-341-031-0
72-63-00-15-700
(4) DE 5/-
NOTE 1:S p e c i /g191cation 2000 Change Codes
- = Not applicable.
1 = One way interchangeable.
5 = Quali /g191ed interchangeability - parts deleted.
5=Q u a l i/g191ed interchangeability - parts added.
5=Q u a l i/g191ed interchangeability - Refer to paragraph 1.K I nterchangeability .
NOTE 2: Spare Parts Support Codes
- = Not applicable.
A = Old parts will no longer be supplied.
D= Old parts will be supplied for engines that have not been changed by the
Service Bulletin.
E = Old parts will be supplied, and can be used at other engine locations.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 12

### Page 15

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NOTE 3: Operation Codes
AD = Added
DE = Deleted
RI = Reidenti /g191ed
RM = Remains
RW = Reworked
SU = Superseded
NOTE 4: This part is not procurable.
D. Disposition of Parts
Part Numbers 340-047-602-0, 340-047-802-0 and 340-052-901-0, removed to accomplish
this Service Bulletin may be locally scrapped.
E. Tooling - Price and Availability
Tool Number Description
856A3545G03 Rigging Fixture
856A1130P12 Jackscrews
856A2961G02 Removal / Installation , Sealol and Magnetic Seals
856A3548G03 T ool Set , T argets - AGB Oil Nozzle Air Impingement Checks
856A3549G02 T ool Set , Leak T est - AGB
856A2969G01 T ool Set , T arget - AGB Oil Nozzle (Line N° 4) Air I mpingement
Check
3. ACCOMPLISHMENT INSTRUCTIONS
NOTE 1: Changes introduced by this Service Bulletin have no effect on the removal/installation
and disassembly/assembly of AGB assembly except for the installation of the new
drain line.
NOTE 2: Changes introduced by this Service Bulletin have no effect on the removal/installation
and disassembly/assembly of starter drive pad assembly except for the installation
of the new oil seal assy.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 13

### Page 16

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NOTE 3: For the new AGB assembly 340-046-508-0 installation, unless speci /g191ed differently
in the installation procedures of the new brackets, to attach the new brackets
340-199-801-0, 340-206-001-0, 340-199-901-0 and 340-091-111-0, you must use the
bolts removed from the new AGB assembly 340-046-508-0 but you must not install
the temporary washers (painted red).
NOTE 4: For the reworked AGB assembly 340-046-508-0 installation, to attach the new
brackets 340-199-801-0, 340-206-001-0, 340-199-901-0 and 340-091-111-0, you
must use the bolts removed from the reworked AGB assembly 340-046-508-0 but
you must discard the associated washers at these brackets locations.
A. Removal of the old AGB assembly 340-046-505-0 equipped with its old starter drive pad
assembly 340-047-802-0, handcranking cover assembly 340-047-602-0 and bracket
assembly 340-091-109-0 from the engine assembly. Refer to Engine Shop Manual (ESM),
ATA 72-00-63, Removal 001. Refer to /g191gure 1.
B. Removal of the old handcranking cover assembly 340-047-602-0 and starter drive pad
assembly 340-047-802-0 from the old AGB assembly 340-046-505-0. Refer to Engine Shop
Manual (ESM), ATA 72-63-00, Disassembly 001. Refer to /g191gure 2, /g191gure 3 and /g191gure 4.
NOTE: This step concerns the rework of old AGB assembly 340-046-505-0 to the new
AGB assembly 340-046-508-0.
(1) Remove the old handcranking cover assembly 340-047-602-0 from the old AGB
assembly 340-046-505-0 as follows :
(a) Remove the bolt AS3237-14 which attach the cable 335-322-901-0 of the
old handcranking cover assembly 340-047-602-0 on the old starter drive pad
assembly 340-047-802-0.
(b) Remove the old bolts AS3237-12 and washers 649-341-031-0 which attach
the old handcranking cover assembly 340-047-602-0.
(c) Remove and discard the old handcranking cover assembly 340-047-602-0.
(d) Remove and discard the two O-rings AS3085-134 or M83248-1-134 from old
handcranking cover assembly.
(2) Remove the old starter drive pad assembly 340-047-802-0 with the handcranking 62
tooth gearshaft assembly 340-051-901-0 from the old AGB assembly 340-046-505-0
as follows :
(a) Remove the bolts AS3237-14 and washers 649-341-031-0 which attach the
old starter drive pad assembly 340-047-802-0 to AGB housing.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 14

### Page 17

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(b) Remove the old starter drive pad assembly 340-047-802-0 with the
handcranking 62 tooth gearshaft assembly 340-051-901-0, use the P12 of
jackscrews, 856A1130.
(c) Install a protective rubber cover on the inner race of the roller bearing
301-480-724-0 or 301-480-726-0 or 301-480-723-0 or 340-055-801-0 of the 62
tooth gearshaft assembly 340-051-901-0.
(3) Remove the handcranking 62 tooth gearshaft assembly 340-051-901-0 from the old
starter drive pad assembly 340-047-802-0 as follows :
(a) Remove the nuts J626P04 which attach the 62 tooth gearshaft assembly
340-051-901-0 with its oil collector 335-309-900-0 from the starter drive pad
assembly 340-047-802-0.
(b) Lightly heat the bearing housing on the starter drive pad assembly
340-047-802-0 with a heat gun. Do not increase the temperature of housing
over 300° F (150° C).
(c) Remove the 62 tooth gearshaft assembly 340-051-901-0 with its ball bearing
335-304-401-0 or 335-304-402-0 or 335-304-403-0 or 340-052-602-0 from the
old starter drive pad assembly 340-047-802-0. Keep the 62 tooth gearshaft
assembly for reinstallation.
(d) Remove and discard the old starter drive pad assembly 340-047-802-0 and
the O-rings J221P163 or 649-393-163-0, J221P158 or 649-393-158-0 and
J221P154 or 649-393-154-0.
(4) Remove the old plug 340-052-901-0 from the old AGB assembly 340-046-505-0 as
follows :
(a) Remove and discard the old plug 340-052-901-0 with its O-rings J221P114
or 649-393-114-0 and J221P013 or 649-393-013-0 from its place on the AGB
housing.
C. Impingement T est of the Oil Nozzle 649-550-005-0 of the new starter drive pad assembly
340-047-804-0. Refer to /g191gure 1, /g191gure 4 and /g191gure 5.
NOTE: This step concerns the rework of old AGB assembly 340-046-505-0 to the new
AGB assembly 340-046-508-0.
(1) Install the target P01of the T arget - AGB oil nozzle air impingement check, tool
(Line N° 4), 856A2969G01 as follows:
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 15

### Page 18

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(a) Install the master index P02 in its location on the target P01 of the T arget -
AGB oil nozzle air impingement check , tool (Line N° 4), 856A2 969G01.
(b) Install the target P01 of the T arget - AGB oil nozzle air impingement check,
tool (Line N° 4), 856A2969G01 in its location on the rear face of the new starter
drive pad assembly 340-047-804-0. Align the holes of the target P01 with the
studs 649-079-402-0.
(c) Attach the target P01 of the T arget - AGB oil nozzle air impingement check,
tool (Line N° 4), 856A2969G01 to the rear face of the new start er drive pad
assembly 340-047-804-0 with the knurled nut P03.
(d) Tighten with hand the knurled nut P03.
(2) Install the new starter drive pad assembly 340-047-804-0 on the support plate P10
of T arget - AGB oil nozzle air impingement check, tool (Line N° 4), 856A2969G01
as follows:
(a) Install the centering pin P14 in its location on the support plate P10 of T arget -
AGB oil nozzle air impingement check, tool (Line N° 4), 856A2 969G01.
(b) Install the support plate P10 of the T arget - AGB oil nozzle air impingement
check, tool (Line N° 4), 856A2969G01 on the adaptation suppo rt of rigging
/g191xture, 856A3545G03.
(c) Attach the support plate P10 to the adaptation support with the two bolts of
rigging /g191xture, 856A3545G03. Tighten with hand the two bolts.
(d) Install the new starter drive pad assembly 340-047-804-0 on the support plate
P10 of the T arget - AGB oil nozzle air impingement check, tool (Line N° 4),
856A2969G01. Align the hole of the starter drive pad with the centering pin
P14.
(e) Install the two threaded rods P13 with /g191xing guides and nuts P15 on their
locations on the support plate P10 of T arget - AGB oil nozzle air impingement
check, tool (Line N° 4), 856A2969G01.
(f) Attach the new starter drive pad assembly 340-047-804-0 to the threaded
rod P13 installed on the support plate P10 of the T arget - AGB oil nozzle air
impingement check, tool (Line N° 4), 856A2969G01 with /g191xing guides and the
nuts P15. Tighten with hand the nuts P15.
(g) Make sure that the starter drive pad assembly 340-047-804-0 is correctly
installed and tightened on the rigging /g191xture, 856A3545G03. Refer to /g191gure 5.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 16

### Page 19

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(3) Install the connecting tube P09 of the T arget - AGB oil nozzle air impingement check,
tool (Line N° 4), 856A2969G01 as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Lightly coat two new O-rings 649-393-013-0 or J221P013 with engine oil
(CP2442) .
(b) Install the O-rings 649-393-013-0 or J221P013 in the grooves of the joint base
P04 (pad side) and joint base P05 (housing side) of the T arget - AGB oil nozzle
air impingement check, tool (Line N° 4), 856A2969G01.
(c) Put the joint base P04 in position at the rear face of the new starter drive pad
assembly 340-047-804-0.
(d) Install the two /g191xing guides, threaded rods P13 and nuts P15 of the T arget -
AGB oil nozzle air impingement check, tool (Line N° 4), 856A2 969G01 from the
front face of the new starter drive pad assembly 340-047-804-0.
(e) Attach the joint base P04 to the new starter drive pad assembly 340-047-804-0
with the two /g191xing guides, threaded rods P13 and nuts P15 of the T arget - AGB
oil nozzle air impingement check, tool (Line N° 4), 856A2969 G01.
(f) Tighten with hand the nuts P15.
(g) Put the joint base P05 in position at the spool 335-310-200-0 location of the
AGB housing.
(h) Attach the joint base P05 to the AGB housing with the two threaded bolts of the
T arget - AGB oil nozzle air impingement check, tool (Line N° 4 ), 856A2969G01.
(i) T i g h t e nw i t hh a n dt h et w ot h r e a d e db o l t s .
(j) Install the connecting tube P09 ( /g192exible) with its threaded adaptors P12 and
BS rings P11 between the two joint bases P04 and P05 of the T arget - AGB oil
nozzle air impingement check, tool (Line N° 4), 856A2969G01 .
(k) Make sure that connecting tube P09 is correctly installed. Refer to /g191gure 5
sheet 2.
(l) Tighten with hand the two coupling nuts of connecting tube P09 of the T arget -
AGB oil nozzle air impingement check, tool (Line N° 4), 856A2 969G01.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 17

### Page 20

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(4) Installation of the test installation T ool set, T argets - AGB oil nozzle air impingement
checks (tool set), 856A3548G02 as follows :
(a) Connect the test installation through connecting /g191tting of T ool set, T argets
- AGB oil nozzle air impingement checks (tool set), 856A3548G02 to the
restrictor nipple 340-054-301-0.
(b) Set the test conditions as follows:
WARNING: CALIBRATION FLUID IS TOXIC AND FLAMMABLE.
USE PERSONAL PROTECTION EQUIPMENT . USE IN A
WELL-VENTILATED AREA.
1 Calibration /g192uid: calibration /g192uid (CP5069) .
2 T emperature: 80.6 to 89.6 deg F (27 to 32 deg C).
3 Supply pressure: 2.9 to 3.1 bar.
4 To t a l A G B/g192ow rate: 115 to 141 US gal/h (436,5 to 533,5 l/h) as monitored
on the /g192owmeter during the test.
(c) After the stability of parameters, supply the pressure to the oil nozzle and
verify the following :
1 The direction of oil jet is correct. 70% of the jet /g192ow rate must pass
through the target.
2 The quality of oil jet is correct. You must have a homogenous jet and
not have a spray pattern.
NOTE: A light spray of oil around the target hole is acceptable. The jet
section can have an incompletely circular shape.
(d) After you complete the test, let the pressure decrease gradually.
(e) If the test result is not correct, replace the new starter drive pad assembly
340-047-804-0 and do the test again.
(f) Disconnect the connecting /g191tting of T ool set, T argets - AGB oil nozzle air
impingement checks (tool set), 856A3548G02 from therestrictor nipple
340-054-301-0.
(5) Remove the connecting tube P09 of the T arget - AGB oil nozzle air impingement
check, tool (Line N° 4), 856A2969G01 as follows:
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 18

### Page 21

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(a) Loosen the two coupling nuts of connecting tube P09 of the T arget - AGB oil
nozzle air impingement check, tool (Line N° 4), 856A2969G01 .
(b) Remove the connecting tube P09 ( /g192exible) and its threaded adaptors P12 and
BS rings P11 from the two joint bases P04 and P05 of the T arget - AGB oil
nozzle air impingement check, tool (Line N° 4), 856A2969G01 .
(c) Loosen the two threaded bolts of the T arget - AGB oil nozzle air impingement
check, tool (Line N° 4), 856A2969G01 which attach the joint b ase P05 to the
AGB housing .
(d) Remove the joint base P05 from the AGB housing.
(e) Loosen and remove the two nuts P15, threaded rods P13 and /g191xing guides
of the T arget - AGB oil nozzle air impingement check, tool (Line N° 4),
856A2969G01 which attach the joint base P04 to the new starter drive pad
assembly 340-047-804-0.
(f) Remove the joint base P04 from the rear face of the new starter drive pad
assembly 340-047-804-0.
(g) Remove and discard the O-rings 649-393-013-0 or J221P013 from the grooves
of the joint base P04 and joint base P05 of the T arget - AGB oil nozzle air
impingement check, tool (Line N° 4), 856A2969G01.
(6) Remove the new starter drive pad assembly 340-047-804-0 from the support plate
P10 of T arget - AGB oil nozzle air impingement check, tool (Line N° 4), 856A2969G01
as follows:
(a) Loosen and remove the threaded rod P13 with the nut P15 and the /g191xing
guide which attach the new starter drive pad assembly 340-047-804-0 on the
support plate P10 of the T arget - AGB oil nozzle air impingement check, tool
(Line N° 4), 856A2969G01.
(b) Remove the new starter drive pad assembly 340-047-804-0 from the support
plate P10 of the T arget - AGB oil nozzle air impingement check, tool (Line
N° 4), 856A2969G01.
(c) Loosen the two bolts which attach the support plate P10 to the adaptation
support of rigging /g191xture, 856A3545.
(d) Remove the support plate P10 of the T arget - AGB oil nozzle air impingement
check, tool (Line N° 4), 856A2969G01 from the adaptation sup port of rigging
/g191xture, 856A3545.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 19

### Page 22

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(e) Remove the centering pin P14 from its location on the support plate P10 of
T arget - AGB oil nozzle air impingement check, tool (Line N° 4 ), 856A2969G01.
(7) Remove the target P01of the T arget - AGB oil nozzle air impingement check, tool
(Line N° 4), 856A2969G01 as follows:
(a) Loosen and remove the knurled nut P03 of the T arget - AGB oil nozzle air
impingement check, tool (Line N° 4), 856A2969G01 which atta ch the target
P01 to the rear face of the new starter drive pad assembly 340-047-804-0.
(b) Remove the target P01 of the T arget - AGB oil nozzle air impingement check,
tool (Line N° 4), 856A2969G01.
(c) Remove the master index P02 from the target P01 of the T arget - AGB oil
nozzle air impingement check , tool (Line N° 4), 856A2969G01 .
D. Installation of the new spool 335-310-200-0 and the new starter drive pad assembly
340-047-804-0 on the new AGB assembly 340-046-508-0. Refer to Engine Shop Manual
(ESM), ATA 72-63-00, Assembly 001. Refer to /g191gure 2, /g191g u r e3a n d/g191gure 4.
NOTE: This step concerns the rework of old AGB assembly 340-046-505-0 to the new
AGB assembly 340-046-508-0.
(1) Install the new spool 335-310-200-0 in its place in the new AGB assembly
340-046-508-0 as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Install the new O-rings 649-393-013-0 or J221P013 on the new spool
335-310-200-0.
(b) Install the new spool 335-310-200-0 with the O-rings 649-393-013-0 or
J221P013 in its place between the AGB housing and the new starter drive
pad assembly 340-047-804-0.
(2) Install the handcranking 62 tooth gearshaft assembly 340-051-901-0 on the new
starter drive pad assembly 340-047-804-0 as follows :
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Lightly coat the outer diameter of the ball bearing 335-304-401-0 or
335-304-402-0 or 335-304-403-0 or 340-052-602-0 of the 62 tooth gearshaft
assembly 340-051-901-0 with engine oil (CP2442) .
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 20

### Page 23

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(b) Heat the bearing housing on the new starter drive pad assembly 340-047-804-0
with a heat gun. Do not increase the temperature of the bearing housing over
311° F (155° C).
(c) Install the ball bearing end of the 62 tooth gearshaft assembly 340-051-901-0
with its oil collector 335-309-900-0 in the new starter drive pad assembly
340-047-804-0 with the studs on pad as locators.
(d) Install correctly the oil collector 335-309-900-0 relative to the ball bearing.
Align the oil collector with the studs on pad. Refer to /g191gure 3 sheet 3.
(e) Attach the 62 tooth gearshaft assembly 340-051-901-0 and its oil collector
335-309-900-0 to the studs 649-079-402-0 of the new starter drive pad
assembly 340-047-804-0 with the self locking nuts J626P04.
(f) Let the parts go back to ambient temperature.
(g) T orque the nuts J626P04 to 97-106 lb in. (11-12 N.m).
(h) Make sure that the 62 tooth gearshaft assembly 340-051-901-0 is correctly
engaged in the starter drive pad assembly 340-047-804-0. Use a 0.0016 inch
(0,04 mm) feeler gage to verify the clearance between the ball bearing /g192ange
and the starter drive pad surface. Refer to Engine Shop Manual (ESM), ATA
72-63-00, Assembly 001
E. Installation of the new oil seal assembly 340-155-304-0, handcranking cover assembly
340-047-605-0 on the new AGB assembly 340-046-508-0. Refer to Engine Shop Manual
(ESM), ATA 72-63-00, Assembly 001. Refer to /g191gure 2, /g191gure 3, /g191gure 4, /g191gure 6 and
/g191gure 7.
NOTE: This step concerns the rework of old AGB assembly 340-046-505-0 to the new
AGB assembly 340-046-508-0.
(1) Assembly of the new removal/installation tool, 856A2961G02 to install the new oil
seal assembly 340-155-304-0 on the handcranking 62 tooth gearshaft assembly
340-051-901-0 as follows: Refer to /g191gure 7.
(a) Install the axe P05 of the removal/installation tool, 856A2961G02 through
the hole of the expander P02.
(b) Install the anti-rotation key P06 into the notch of the axe P05 of the
removal/installation tool, 856A2961G02.
(c) Install the ring P08 of the removal/installation tool, 856A2961G02 on the collet
P01. Align the holes and /g191xe with the Pins P09.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 21

### Page 24

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(d) Insert the axe P05 equipped with the anti-rotation keys P06 and expander P02
of the removal/installation tool, 856A2961G02 into the collet P01.
(e) Align the anti-rotation key P06 with the guide splines of the collet P01 of the
removal/installation tool, 856A2961G02.
(f) Install the nut P04 on the axe P05 of the removal/installation tool,
856A2961G02.
(g) Install the retaining ring P07 on the axe P05 of the removal/installation tool,
856A2961G02.
(h) Install the assembly (collet P01, expander P02, axe P05 and nut P04) of the
removal/installation tool, 856A2961G02 into the sleeve P03.
CAUTION: USE CLEAN, LINT-FREE GLOVES WHEN YOU TOUCH THE OIL SEAL
TO PREVENT CONTAMINATION.
(2) Install the mating ring 340-155-601-0 of new oil seal assembly 340-155-304-0 on
the handcranking 62 tooth gearshaft assembly 340-051-901-0 as follows: Refer to
/g191gure 3, /g191gure 6 and /g191gure 7
CAUTION: MAKE SURE THE POLISHED FACE OF THE MATING RING AND
THE CARBON FACE OF THE SEAL HOUSING ARE CLEAN. LEAKS
WILL OCCUR IF PARTICLES, EVEN OF A VERY SMALL SIZE, ARE
BETWEEN THESE PARTS DURING THE INSTALLATION.
(a) Clean the mating surface of the mating ring 340-155-601-0 with tissue paper.
(b) Clean the glazed surface of the oil seal 340-155-504-0 with tissue paper.
WARNING: VAT TANK COVERS AND EXTINGUISHERS MUST BE AVAILABLE IF
A FIRE OCCURS. SOLVENT IS FLAMMABLE.
WARNING: CLEANING SOLVENT IS TOXIC AND FLAMMABLE. USE PERSONAL
PROTECTIVE EQUIPMENT . USE IN A WELL-VENTILATED AREA.
CAUTION: OBEY THE ENVIRONMENTAL REGULATION WHEN YOU DISCARD
CONSUMABLE PRODUCTS.
(c) Clean the surface of the handcranking 62 tooth gearshaft assembly
340-051-901-0 mating with the oil seal mating ring with a lint-less cloth
moistened by Acetone (CP1039) .
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 22

### Page 25

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(d) Lightly coat the O-ring 340-196-401-0 of the new oil seal assembly
340-155-304-0 with vaseline (CP5070) .
(e) Install the O-ring 340-196-401-0 in the groove at the inner diameter of new
mating ring 340-155-601-0.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(f) Lightly coat the mating surface of the mating ring 340-155-601-0 with engine
oil (CP2442) .
(g) Lightly coat the mating surfaces of the handcranking 62 tooth gearshaft
assembly 340-051-901-0 which is in contact with the O-ring 340-196-401-0 on
the mating ring 340-155-601-0 with engine oil (CP2442) .
(h) Install the centering guide P10 of the removal/installation tool, 856A2961G02
on the new starter drive pad assembly 340-047-804-0 with its three tool /g191xing
screws P11.
(i) Loosen the nut P04 and the collet P01 of removal/installation tool,
856A2961G02.
(j) Install the mating ring 340-155-601-0 on the claws of the collet P01 of
removal/installation tool, 856A2961G02.
(k) Tighten with hand the collet P01 and the nut P04 of removal/installation tool,
856A2961G02. Make sure that the position of ring is correct in the claws of
the collet.
(l) Tighten with hand the sleeve P03 of removal/installation tool, 856A2961G02 to
lock the mating ring 340-155-601-0 in the claws of the collet.
(m) Insert the mating ring 340-155-601-0 with the removal/installation tool,
856A2961G02 into its centering guide P10.
(n) Install the mating ring 340-155-601-0 on the handcranking 62 tooth gearshaft
assembly 340-051-901-0 with the removal/installation tool, 856A2961G02.
(o) Turn the removal/installation tool, 856A2961G02 until the lugs of mating ring
340-155-601-0 engage into the slots of the ball bearing inner race.
(p) Visually make sure that the mating ring 340-155-601-0 is correctly installed :
the bottom face of the side window of sleeve P03 of removal/installation tool,
856A2961G02 must be in line with the AGB forward face.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 23

### Page 26

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(q) Loosen the sleeve P03 of removal/installation tool, 856A2961G02.
(r) Push the removal/installation tool, 856A2961G02 to make sure that the mating
ring 340-155-601-0 stays in place.
CAUTION: MAKE SURE THAT THE COLLET CLAWS ARE TOTALLY LOOSENED
AND THAT YOU DO NOT PULL AND DISENGAGE THE MATING
RING WITH THE REMOVAL/INSTALLATION TOOL. RING DAMAGE
AND OIL LEAKAGE CAN OCCUR.
(s) Loosen the nut P04 and the collet P01 of theremoval/installation tool,
856A2961G02.
(t) Remove theremoval/installation tool, 856A2961G02 from the centering guide
P10.
(u) Loosen the three tool /g191xing screws P11 and remove the P10 centering guide
of the removal/installation tool, 856A2961G02 from the new starter drive pad
assembly 340-047-804-0.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(v) Lightly coat the mating surface of the mating ring 340-155-601-0 with engine
oil (CP2442) .
CAUTION: USE CLEAN, LINT-FREE GLOVES WHEN YOU TOUCH THE OIL SEAL
TO PREVENT CONTAMINATION.
(3) Prepare the installation of oil seal housing 340-155-504-0 of new oil seal assembly
340-155-304-0 as follows: Refer to /g191gure 3, /g191g u r e6a n d/g191gure 7
WARNING: VAT TANK COVERS AND EXTINGUISHERS MUST BE AVAILABLE IF
A FIRE OCCURS. SOLVENT IS FLAMMABLE.
WARNING: CLEANING SOLVENT IS TOXIC AND FLAMMABLE. USE PERSONAL
PROTECTIVE EQUIPMENT . USE IN A WELL-VENTILATED AREA.
CAUTION: OBEY THE ENVIRONMENTAL REGULATION WHEN YOU DISCARD
CONSUMABLE PRODUCTS.
(a) Remove the grease from the mating surface of oil seal housing assembly
340-155-504-0 with a lint-less cloth moistened by acetone (CP1039) .
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 24

### Page 27

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(b) Remove the grease from the mating surface of new starter drive pad assembly
340-047-804-0 with a lint-less cloth moistened by acetone (CP1039) .
(c) Apply a bead of silicone elastomer sealant RTV102 (CP2266) or RTV103 on
the external diameter of seal housing Dim. E.
1 With a template with chamfer 3 mm and 45° , apply the bead of sil icone
elastomer sealant on Dim. E all over the diameter. Dim. E must be 0.12
inch (3,00 mm) except for the location of minimum mating surface between
seal housing and starter drive pad. In this location the minimum distance
must be 0.039 inch (1,00 mm).
2 Make sure that the bead of silicone elastomer sealant is regularly
distributed without any cutting specially in the location of minimum mating
surface between seal housing and starter drive pad.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(d) Lightly coat the O-ring 649-393-034-0 or J221P034 of the new oil seal
assembly 340-155-304-0 with engine oil (CP2442) .
(e) Install the O-ring 649-393-034-0 or J221P034 in the groove at the outer
diameter of new oil seal 340-155-504-0.
CAUTION: BE CAREFUL DO NOT HIT THE OIL SEAL INTO THE GEARBOX
RECESS. THE MATING RING CAN MOVE APART AND CARBON
SEAL CAN BE DAMAGED.
(f) Install the oil seal housing assembly 340-155-504-0 on handcranking 62 tooth
gearshaft assembly 340-051-901-0. Slowly lower the housing assembly.
(g) Make sure that the housing of oil seal 340-155-504-0 is correctly engaged
with the centering pin 340-155-801-0 on the new starter drive pad assembly
340-047-804-0.
(h) Apply a thin layer of vaseline (CP5070) on the threads of two bolts AS3236-08.
(i) Attach the housing oil seal 340-155-504-0 with the two bolts AS3236-08 to the
inserts J970P03 of new starter drive pad assembly 340-047-804-0. Refer
to/g191gure 3, sheet 4.
(j) T orque the bolts AS3236-08 which attach the housing of oil seal 340-155-504-0
to 49-58 lb in. (5.5-6.5 N.m).
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 25

### Page 28

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(k) Make sure that the draining ori /g191ce on the oil seal housing 340-155-504-0 is
completely free from RTV102 (CP2266) or RTV103 silicone elastomer sealant
bead. If not, remove the excess of sealant with spatula.
(l) Remove the excess of RTV102 (CP2266) or RTV103 silicone elastomer
sealant all over the oil seal housing outer diameter with dry lint-less cloth and
spatula.
(m) Put the assembly into an oven at 293° F (145° C) during 30 minut es to
polymerize the sealant.
(n) Remove the assembly from the oven and let it go to the ambient temperature.
(4) Install the new starter drive pad assembly 340-047-804-0 with the handcranking 62
tooth gearshaft assembly 340-051-901-0 on the new AGB assembly 340-046-508-0
as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Lightly coat the new O-rings J221P163 or 649-393-163-0, J221P158 or
649-393-158-0 and J221P154 or 649-393-154-0 with engine oil (CP2442) .
(b) Install the new O-rings J221P163 or 649-393-163-0, J221P154 or
649-393-154-0 on the new starter drive pad assembly 340-047-804-0.
(c) Install the new O-ring J221P158 or 649-393-158-0 on the AGB housing.
(d) Remove the rubber cover from the inner race of the roller bearing
301-480-720-0or 301-480-724-0 or 301-480-726-0 or 301-480-723-0 or
340-055-801-0 of the 62 tooth gearshaft assembly 340-051-901-0.
(e) Lower carefully the new starter drive pad assembly 340-047-804-0 with the 62
tooth gearshaft assembly 340-051-901-0 in position.
Do a special attention when you engage the inner race of the roller bearing
301-480-720-0 or 301-480-724-0 or 301-480-726-0 or 301-480-723-0 or
340-055-801-0 with its outer race.
(f) Do a special attention when you engage the new O-rings J221P163 or
649-393-163-0 and J221P154 or 649-393-154-0 in the AGB housing.
(g) Apply a thin layer of Graphite compound (CP2101) on the threads of bolts
AS3237-14.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 26

### Page 29

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(h) Install the bolts AS3237-14 and washers 649-341-031-0 which attach the new
starter drive pad assembly 340-047-804-0 to AGB housing.
(i) T orque the bolts AS3237-14 which attach the new starter drive pad assembly
340-047-804-0 to 97-106 lb in. (11-12 N.m).
F. Installation of the new brackets 340-199-801-0 and 340-206-001-0 for the new
handcranking pad drain tube 340-200-002-0 on the Accessory Gearbox assembly (AGB)
340-046-508-0. Refer to /g191gure 2 and /g191g u r e9.
NOTE: In production, the new AGB 340-046-508-0 have temporary washers (painted in
red color) into new brackets locations.
(1) Install the new bracket 340-206-001-0 on the new starter drive pad assembly
340-047-804-0 as follows:
(a) Remove the two bolts AS3237-14 and washers 649-341-031-0 or temporary
washers to attach the new bracket 340-206-001-0 on AGB housing through
starter drive pad assembly 340-047-804-0.
(b) Discard the two washer 649-341-031-0 or temporary washers.
(c) Put the new bracket 340-206-001-0 in position on the new starter drive pad
assembly 340-047-804-0.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(d) Apply a thin layer of engine oil (CP2442) on the threads of bolts AS3237-14.
(e) Install the two bolts AS3237-14 and washers 649-341-031-0 to attach the
bracket 340-206-001-0 to the AGB housing through the new starter drive pad
assembly 340-047-804-0.
(f) T orque the bolt AS3237-14 to 97-106 lb in. (11-12 N.m).
(g) Wipe off the excessive engine oil (CP2442) on the surface of the bracket.
(2) Install the new bracket 340-199-801-0 on the hydraulic pump drive pad assembly
340-048-802-0 as follows:
(a) Remove the two bolts AS3237-12 and washer 649-341-031-0 to attach the
new bracket 340-199-801-0 on AGB housing through hydraulic pump drive
pad assembly 340-048-802-0.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 27

### Page 30

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(b) Discard the two washer 649-341-031-0 or temporary washers.
(c) Put the new bracket 340-199-801-0 in position on the new hydraulic pump
drive pad assembly 340-048-802-0.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(d) Apply a thin layer of engine oil (CP2442) on the threads of bolts AS3237-12.
(e) Install the two bolts AS3237-12 and washer 649-341-031-0 to attach the
bracket 340-199-801-0 to the AGB housing through the hydraulic pump drive
pad assembly 340-048-802-0.
(f) T orque the bolts AS3237-12 to 97-106 lb in. (11-12 N.m).
(g) Wipe off the excessive engine oil (CP2442) on the surface of the bracket.
G. Do the leak test of the new AGB assembly 340-046-508-0 before its installation on the
engine assembly. Refer to Engine Shop Manual (ESM), ATA 72-63-00, Assembly 001.
NOTE 1: This step concerns the rework of old AGB assembly 340-046-505-0 to the
new AGB assembly 340-046-508-0.
NOTE 2: When you do the leak test shown in Engine Shop Manual (ESM), ATA
72-63-00, Assembly 001, use the spray leak detector to detect any air leakage.
NOTE 3: When you /g191nish the leak test shown in Engine Shop Manual (ESM), ATA
72-63-00, Assembly 001, do the following steps to make sure that the new
oil seal assembly 340-155-304-0 correctly operates and there in no leakage
through it.
(1) Connect the test air supply source to the nipple J1037P06 of new starter drive pad
assembly 340-047-804-0.
(2) Supply air to the starter drive pad and make sure that the draining ori /g191ce is fully free
of RTV102 (CP2266) or RTV103 silicone elastomer sealant.
(3) Install the new handcranking cover assembly 340-047-605-0 on the new starter drive
pad assembly 340-047-804-0 of new AGB assembly 340-046-508-0 as follows :
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 28

### Page 31

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(a) Apply a thin layer of engine oil (CP2442) on new O-ring 649-393-137-0 or
J221P137.
(b) Install the new O-ring 649-393-137-0 or J221P137 in its place between the
new handcranking cover assembly 340-047-605-0 and the housing of oil
seal 340-155-504-0.
(c) Install the new handcranking cover assembly 340-047-605-0 on the housing of
oil seal 340-155-504-0.
(d) Make sure that the the new handcranking cover assembly 340-047-605-0 is
correctly seated on the housing of oil seal 340-155-504-0.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(e) Apply a thin layer of engine oil (CP2442) on the threads of bolts AS3237-12.
(f) Attach the new handcranking cover assembly 340-047-605-0 to the new
starter drive pad assembly 340-047-804-0 with the new three bolts AS3237-12
and washers 649-341-031-0.
(g) Attach the new cable 335-322-902-0 of new handcranking cover assembly
340-047-605-0 to the new starter drive pad assembly 340-047-804-0 with the
bolt AS3237-14. Refer to /g191gure 3 sheets 4 and 5.
(h) T orque the new bolts AS3237-12 to 97-106 lb in. (11-12 N.m).
(i) T orque the bolt AS3237-14 to 97-106 lb in. (11-12 N.m).
(4) Connect the test air supply hose under the following conditions to union P05 of
leak test tool set, 856A3549G02, to the nipple J1037P06 of new starter drive pad
assembly 340-047-804-0:
(a) Water content: dew point -40° F (-40° C) at atmospheric press ure.
(b) T emperature: ambient.
(c) Air /g191ltration: lower than 40 microns, absolute.
NOTE: If the air supply source does not agree with the above test conditions,
replace by nitrogen of quality R.
(d) Deoiling: weight of remaining oil, less than 40 mg/kg of air.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 29

### Page 32

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(5) Do the test as follows, Slowly pressurize the oil seal compartment up to 10-12 psig
(70-80 kPa gage).
(6) When you get the pressure level, close the test installation isolation valve and close
the air supply.
(7) Make sure that the pressure level is stable on the test installation pressure gage for
10 minutes. There must be no pressure decrease shown on the pressure gage. If
so, correct as follows:
(a) Find the leak, use spray leak detector.
(b) Depressurize the oil seal compartment.
(c) Remove the oil seal and install a new one.
(d) Do the leak test again.
(8) At completion of the leak test, release the pressure in the oil seal compartment.
H. Re-identi/g191cation of the Old AGB assembly 340-046-505-0 to the new Part Number
340-046-508-0.
NOTE: This step concerns the rework of old AGB assembly 340-046-505-0 to the new
AGB assembly 340-046-508-0.
(1) Re-identi/g191cation of the old AGB assembly 340-046-505-0 to the new AGB assembly
340-046-508-0. Refer to SPM, ATA 70-10-12, Vibro-Peen Marking as follows:
(a) Score out the old Part Number of the old AGB assembly 340-046-505-0 on the
AGB assembly identi /g191cation plate. Refer to /g191gure 1.
(b) Mark the new Part Number of the new AGB assembly 340-046-508-0 and the
Service Bulletin Number on the AGB assembly Identi /g191cation plate.
I. Installation of the new AGB assembly 340-046-508-0 on the engine assembly. Refer to
Engine Shop Manual (ESM), ATA 72-00-63, Installation 001. Refer to /g191gure 2 and /g191gure 9.
NOTE 1: When you install the unchanged brackets and bracket assemblies on the new
AGB 340-046-508-0, install the new bracket assembly 340-091-111-0.
NOTE 2: When you install the oil return tube 340-015-302-0, install the new bracket
340-199-901-0. Refer to /g191gure 9
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 30

### Page 33

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NOTE 3: In production, the new AGB 340-046-508-0 have temporary washers (painted
in red color) into new bracket location.
(1) Install the new bracket assembly 340-091-111-0 on the new AGB assembly
340-046-508-0. Refer to /g191gure 2.
(a) Remove the four bolts AS3237-14 and the washer 649-341-031-0 or temporary
washer to attach the new bracket assy 340-091-111-0 on AGB housing through
the new starter drive pad assembly 340-047-804-0.
(b) Discard the washer 649-341-031-0 or temporary washer.
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(c) Apply a thin layer of engine oil (CP2442) on the threads of bolts AS3237-14
and AS3237-10.
(d) Put the new bracket assembly 340-091-111-0 in position on the new starter
drive pad assembly 340-047-804-0.
(e) Put in position the cable 335-322-902-0 of the new handcranking cover
assembly 340-047-605-0 on the new bracket assembly 340-091-111-0.
(f) Attach the new bracket assembly 340-091-111-0 to AGB housing through the
new starter drive pad assembly 340-047-804-0 with bolts AS3237-14.
(g) Attach the new bracket assembly 340-091-111-0 to the bracket assembly
340-107-802-0 with bolts AS3237-10, washers 649-341-011-0 and nuts
AS3486-10.
(h) T orque the bolts AS3237-10 to 97-106 lb in. (11-12 N.m).
(i) T orque the bolts AS3237-14 to 97-106 lb in. (11-12 N.m).
(j) Wipe off the excessive engine oil (CP2442) on the surface of the bracket.
(2) Install the new bracket assy 340-199-901-0 on the /g192ange of oil return tube
340-015-302-0 as follows:
NOTE: When you install the oil return tube, remove the plug N100-226 from the
AGB housing.
(a) Put the new bracket 340-199-901-0 in position on the /g192ange of oil return
tube 340-015-302-0.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 31

### Page 34

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(b) Apply a thin layer of Graphite compound (CP2101) on the threads of new
bolts AS3236-12.
(c) Install the new bolts AS3236-12 to attach the bracket 340-199-901-0 to the
AGB housing through the /g192ange of oil return tube 340-015-302-0.
(d) T orque the new bolts AS3236-12 to 50-60 lb in. (5,5-7 N.m).
J. Installation of the new handcranking pad drain tube 340-200-002-0 on the new Accessory
Gearbox assembly (AGB) 340-046-508-0. Refer to /g191gure 2, /g191gure 4 and /g191gure 9.
(1) Install the drain tube 340-200-002-0 to the new nipple J1037P06 of the new starter
drive pad assembly 340-047-804-0:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Apply a thin layer of Engine oil (CP2442) on the threads of nipple J1037P06.
(b) Attach the locking nut of the drain tube 340-200-002-0 to nipple J1037P06.
(2) Install the drain tube 340-200-002-0 on the new bracket 340-206-001-0 on the new
starter drive pad assembly 340-047-804-0 as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Apply a thin layer of Engine oil (CP2442) on the threads of bolt AS3237-08
which attach the drain tube 340-200-002-0 on the new bracket 340-206-001-0.
(b) Install the clamp J1431P06 on the drain tube 340-200-002-0.
(c) Attach the drain tube 340-200-002-0 on the new bracket 340-206-001-0 with
clamp J1431P06, bolt AS3237-08 and nut AS3486-10.
(3) Install the new drain tube 340-200-002-0 on the new bracket 340-199-801-0 on the
hydraulic pump drive pad assembly 340-048-802-0 as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Apply a thin layer of Engine oil (CP2442) on the threads of bolts AS3237-08
which attach the drain tube 340-200-002-0 on the new bracket 340-199-801-0.
(b) Install the clamps J1431P06 on the drain tube 340-200-002-0.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 32

### Page 35

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
(c) Attach the drain tube 340-200-002-0 on the new bracket 340-199-801-0 with
two clamps J1431P06, bolts AS3237-08 and nuts AS3486-10.
(4) Install the new drain tube 340-200-002-0 on the new bracket 340-199-901-0 on the
/g192ange of oil return tube 340-015-302-0 as follows:
WARNING: ENGINE OIL IS TOXIC. USE PERSONAL PROTECTION
EQUIPMENT . USE IN A WELL-VENTILATED AREA.
(a) Apply a thin layer of Engine oil (CP2442) on the threads of bolt AS3237-08
which attach the drain tube 340-200-002-0 on the new bracket 340-199-901-0.
(b) Install the clamp J1431P06 on the drain tube 340-200-002-0.
(c) Attach the drain tube 340-200-002-0 on the new bracket 340-199-801-0 with
two clamps J1431P06, bolts AS3237-08 and nuts AS3486-10.
(5) Final tightening of the new drain tube 340-200-002-0 as follows:
(a) Make sure that the drain tube 340-200-002-0 is not strained.
(b) T orque the coupling nut of the drain tube 340-200-002-0 on the new nipple
J1037P06 of the new starter drive pad assembly 340-047-804-0 to 270-315 Ib
in. (30-35 N.m).
(c) T orque the bolts AS3237-08 which attach the drain tube 340-200-002-0 on the
new brackets 340-206-001-0, 340-199-801-0 and 340-199-901-0 to 63-72
lb in. (7-8 N.m).
(d) Wipe off the excessive engine oil (CP2442) on the coupling nut and brackets.
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 33

### Page 36 (OCR)

cfm  SERVICE
BULLETIN
THE POWER  CFM56-7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
VIEW A
BRACKET ASSY
340-091-109-0
AREA OF
CHANGE
AREA OF
HANDCRANKING
CHANGE  COVER ASSY
STARTER DRIVE
PAD ASSY
AREA OF
CHANGE
AGB ASSEMBLY
IDENTIFICATION
PLATE
AREA OF
CHANGE
BRACKET ASSY
AREA OF  HYDRAULIC PUMP
CHANGE  DRIVE PAD ASSY  S-M56-SB-01378-00-в
Location of Change
Figure 1
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 34

### Page 37 (OCR)

~
((cfm))  SERVICE
BULLETIN
THE POVER CFM56-ZB _  OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
OLD CONFIGURATION
BRACKET ASSY
340-091-109-0
BRACKET ASSY
340-107-802-0
HANDCRANKING
COVER ASSY  WASHER
340-047-602-0  649-341-031-0
(ONE LOCATION
TO BE DELETED)
STARTER DRIVE  BRACKET ASSY
PAD ASSY  340-105-801-0 OR
340-047-802-0  340-105-802-0
BRACKET ASSY
BOLT  • 340-089-105-0 OR
AS3237-14  340-089-106-0
WASHER  BRACKET
649-341-031-0  340-105-701-0
(FOUR LOCATIONS
TO BE DELETED)  BRACKET ASSY
340-105-605-0 OR
340-105-606-0
HYDRAULIC PUMP
DRIVE PAD ASSY
340-048-802-0
S-M56-SB-01380-01-B
Removal / Installation of the Handcranking Cover and Starter Drive Pad Assemblies
Figure 2, Sheet 1 of 2
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 35

### Page 38 (OCR)

cfm  SERVICE
BULLETIN
THE POWER  CFM56-7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NEW CONFIGURATION
BRACKET ASSY
340-091-111-0
HANDCRANKING
COVER ASSY
340-047-605-0  BRACKET ASSY
340-107-802-0
BOLT
AS3237-14
WASHER
649-341-031-0  BRACKET ASSY
340-105-801-0 OR
340-105-802-0
NIPPLE
J1037P06
BRACKET ASSY
STARTER DRIVE  340-089-105-0 OR
PAD ASSY  340-089-106-0
340-047-804-0
BRACKET
BRACKET  340-105-701-0
340-206-001-0
BRACKET ASSY
340-105-605-0 OR
340-105-606-0
BRACKET
340-199-801-0
HYDRAULIC PUMP
DRIVE PAD ASSY
340-048-802-0
BRACKET ASSY
340-199-901-0
S-M56-SB-01381-02-B
Removal / Installation of the Handcranking Cover and Starter Drive Pad Assemblies
Figure 2, Sheet 2 of 2
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 36

### Page 39 (OCR)

(cfm,  SERVICE
BULLETIN
THE POWER  CFM56- 7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
SECTION AA
OLD CONFIGURATION
STARTER DRIVE
PAD ASSY
340-047-802-0
O-RING
J221P154 OR
649-393-154-0
STUD
649-079-402-0  NUT
J626P04
HANDCRANKING
COVER  ROLLER BEARING
340-047-702-0  301-480-720-0 OR
301-480-723-0 OR
301-480-724-0 OR
301-480-726-0 OR
HANDCRANKING  340-055-801-0
COVER ASSY
340-047-602-0  OIL COLLECTOR
335-309-900-0
O-RING
AS3085-134 OR  62 TOOTH
M83248-1-134  HANDCRANKING
GEARSHAFT ASSY
BALL BEARING  340-051-901-0
335-304-401-0 OR
335-304-402-0 OR
335-304-403-0 OR
340-052-602-0
O-RING
J221P163 OR
649-393-163-0
O-RING
J221P158 OR
649-393-158-0
S-M56-SB-01382-00-B
Old and New Configuration of Handcranking 62 Tooth Gearshaft and Cover Assemblies
Figure 3, Sheet 1 of 5
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 37

### Page 40 (OCR)

cfm  SERVICE
BULLETIN
THE POWER  CFM56- 7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
OLD CONFIGURATION
VIEW B
00
CABLE
335-322-901-0
HANDCRANKING  WASHER  BOLT
COVER ASSY  649-341-031-0  AS3237-12
340-047-602-0
s-M56-SB-01379-00-B
Old and New Configuration of Handcranking 62 Tooth Gearshaft and Cover Assemblies
Figure 3, Sheet 2 of 5
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 38

### Page 41 (OCR)

(icfm)  SERVICE
BULLETIN
tor Fict CFM56-7B  OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
SECTION AA
NEW CONFIGURATION
STARTER DRIVE
PAD ASSY
340-047-804-0
O-RING
J221P154 OR
649-393-154-0
O-RING
J221P163 OR  NUT
649-393-163-0  J626P04
O-RING
649-393-034-0 OR  STUD
J221P034  649-079-402-0
OIL SEAL ASSY
340-155-304-0  ROLLER BEARING
301-480-720-0 OR
301-480-723-0 OR
301-480-724-0 OR
HANDCRANKING  301-480-726-0 OR
COVER ASSY  340-055-801-0
340-047-605-0
O-RING  OIL COLLECTOR
649-393-137-0 OR  335-309-900-0
J221P137
62 TOOTH
BALL BEARING  HANDCRANKING
335-304-401-0 OR  GEARSHAFT ASSY
335-304-402-0 OR  340-051-901-0
335-304-403-0 OR
340-052-602-0
O-RING
J221P158 OR
649-393-158-0
S-M56-SB-01383-02-B
Old and New Configuration of Handcranking 62 Tooth Gearshaft and Cover Assemblies
Figure 3, Sheet 3 of 5
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 39

### Page 42 (OCR)

cfm  SERVICE
BULLETIN
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NEW CONFIGURATION
VIEW B
BOLT
AS3237-14
BOLT
AS3236-08
CABLE
335-322-902-0
OIL CIA
CAUTION
ESTED
HANDCRANKING  WASHER  BOLT
COVER ASSY  649-341-031-0  AS3237-12
340-047-605-0
s-M56-SB-01384-02-B
Old and New Configuration of Handcranking 62 Tooth Gearshaft and Cover Assemblies
Figure 3, Sheet 4 of 5
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 40

### Page 43 (OCR)

(icfm)  SERVICE
BULLETIN
TOF HIGHT CFM56-7B  OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
OLD CONFIGURATION
SECTION BB
O-RING
PLUG  J221P114 OR
340-052-901-0  649-393-114-0
STARTER DRIVE
PAD ASSY
340-047-804-0
• AGB HOUSING  • B
O-RING J22P013
OR 649-393-013-0
NEW CONFIGURATION
SECTION BB
SPOOL
335-310-200-0  O-RING
649-393-013-0 OR
J221P013
STARTER DRIVE  AGB HOUSING
PAD ASSY
340-047-804-0
S-M56-SB-01392-02-B
Old and New Configuration of Handcranking 62 Tooth Gearshaft and Cover Assemblies
Figure 3, Sheet 5 of 5
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 41

### Page 44 (OCR)

cfm  SERVICE
BULLETIN
TOF FICHT CFM56-7B  OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
OLD CONFIGURATION
INSERT
INSERT  649-680-056-0
649-680-055-0  OR J970P04
OR J970P03  (3 LOCATIONS)
+
INSERT
649-680-056-0
OR J970P04
(6 LOCATIONS)
STARTER DRIVE
PAD ASSY
340-047-802-0
C
SECTION CC
S-M56-SB-01385-01-B
Old and New Configuration of the Starter Drive Pad Assy
Figure 4, Sheet 1 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 42

### Page 45 (OCR)

(cfm)  SERVICE
BULLETIN
THE POWER  CFM56- 7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NEW CONFIGURATION
INSERT
J970P04
(8 LOCATIONS)
INSERT
J970P03
(2 LOCATIONS)  J970P03  INSERT
(2 LOCATIONS)
NIPPLE
J1037P06
STARTER DRIVE
PAD ASSY
340-047-804-0
SECTION CC
S-M56-SB-01386-02-B
Old and New Configuration of the Starter Drive Pad Assy
Figure 4, Sheet 2 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 43

### Page 46 (OCR)

cim  SERVICE
BULLETIN
THE POWER  CFM56-7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
SECTION DD
PLUG
340-152-101-0
LOCATION
OIL NOZZLE
649-550-005-0
CENTERING
SECTION EE  PIN
340-155-801-0
O-RING
NIPPLE
649-393-012-0 OR
J1037P06  J221P012
S-M56-SB-01387-02-B
Old and New Configuration of the Starter Drive Pad Assy
Figure 4, Sheet 3 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011

### Page 47 (OCR)

(cfm))  SERVICE
BULLETIN
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
THREADED
ADAPTOR
P12  O-RING
BS RING  P07
P11  JOINT BASE
(PAD SIDE)
P04
THREADED BOLT
TARGET
P01
KNURLED
NUT
O-RING  РОЗ
PZ
JOINT BASE  MASTER
(HOUSING  INDEX
SIDE)  P02
P05
CONNECTING
TUBE
P09
AGB HOUSING  SUPPORT  CENTERING
PLATE  PIN
P10  P14
INSERT
P16
S-M56-SB-04447-00-B
Impingement Test of the Oil Nozzle on the Starter Drive Pad
Figure 5, Sheet 1 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 45

### Page 48 (OCR)

cfm  SERVICE
BULLETIN
THE POWER  CFM56-7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
DETAIL A
THREADED  NUT P15
ROD P13
FIXING
GUIDE
HEXAGONAL
NUT
P15
(4 LOCATIONS)
THREADED
ROD
CONNECTING  P13
TUBE  (4 LOCATIONS)
P09
s-M56-SB-O4448-00-B
Impingement Test of the Oil Nozzle on the Starter Drive Pad
Figure 5, Sheet 2 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 46

### Page 49 (OCR)

(icfm)  SERVICE
BULLETIN
THE POWER  CFM56- 7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
VIEW B
RESTRICTOR NIPPLE
340-054-301-0
S-M56-SB-04449-00-B
Impingement Test of the Oil Nozzle on the Starter Drive Pad
Figure 5, Sheet 3 of 3
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 47

### Page 50 (OCR)

(cfm/  SERVICE
BULLETIN
TOF FICHT CFM56-7B  OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
SECTION FF
SILICONE
OIL SEAL ASSY  ELASTOMER
340-155-304-0  SEALANT
RTV 102
OR
RTV 103
OIL SEAL SUBASSY
340-155-404-0
DIM. E  0.039
(1,00)
CARBON SEAL
RING ASSY
O-RING
340-196-401-0
MATING RING
340-155-601-0
OIL SEAL
340-155-504-0
NOTE:
DIMENSIONS ARE IN INCHES WITH
MILLIMETERS IN PARENTHESES.  S-M56-SB-01388-02-B
New Oil Seal Assy
Figure 6
October 13, 2009
Revision 3, May 25, 2011

### Page 51 (OCR)

(icfm)  SERVICE
BULLETIN
THE POWER  CFM56- 7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
NUT
P04
AXE  RETAINING RING
P07
P05
RING
PIN  P08
P09
ANTI-ROTATION KEY
COLLET  P06
P01
CENTERING GUIDE
SLEEVE  P10
РОЗ
BOLT
EXPANDER  P11
P02
STATER DRIVE
PAD ASSY
00004
MATING
BALL BEARING  RING
INNER RACE
62 TOOTH
GEARSHAFT
S-M56-SB-01389-01-B
Installation of the Mating Ring of the New Oil Seal Assy
Figure 7
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 49

### Page 52 (OCR)

cim  SERVICE
BULLETIN
THE POWER  CFM56-7B
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
OLD CONFIGURATION
HANDCRANKING  COVER ASSY  OOIL LEAK
340-047-602-0  OiL CIRCUM
CABLE
335-322-901-0
CAUTION
8
NOT FORCE  OR EQUES 120
HANDCRANKING
COVER
340-047-702-0
NEW CONFIGURATION
HANDCRANKING
- COVER ASSY -  CABLE
340-047-605-0  335-322-902-0
OIL LEAKO  CAUTION  OPENING
REQUES NO  REQUESTED  8  YOT FORGET S
HANDCRANKING
COVER
340-047-704-0
s-M56-SB-01390-00-B
Old and New Configuration of the Handcranking Cover Assy
Figure 8
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 50

### Page 53 (OCR)

((cfm))  SERVICE
BULLETIN
OF FLIGHT
ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
BRACKET ASSY
340-091-111-0
BOLT
AS3237-14
DRAINE TUBE  BRACKET ASSY
340-200-002-0  340-105-801-0 OR
340-105-802-0
CLAMP
J1431P06
BOLT
AS3237-08
NUT
AS3486-10
(4 LOCATIONS)
BRACKET
340-105-701-0
BRACKET
340-199-801-0
BRACKET
340-206-001-0
OIL RETURN
TUBE
340-015-302-0
BRACKET ASSY
- AS3236-12
BRACKET
340-199-901-0
S-M56-SB-01391-01-B
Installation of the New Handcranking Pad Drain Line
Figure 9
October 13, 2009  CFM56-7B S/B 72-0564
Revision 3, May 25, 2011  PAGE 51

### Page 54

ENGINE - General (72-00-00) - Introduction of a New Accessory Gearbox Assembly (AGB) with a New
Starter Drive Pad and Rework of the Old AGB to the New One
4. A - PARTS PROGRESSION CHART
Part Number
Part Name
and/or
Characteristics
Identi/g191ed by
Service Bulletin No.
340-046-503-0 Gearbox Assy Accessory Baseline
340-046-504-0 Gearbox Assy Accessory 72-0316
340-046-505-0 Gearbox Assy Accessory 72-0689
340-046-508-0 Gearbox Assy Accessory 72-0564
340-047-601-0 Cover - Assy baseline
340-047-602-0 Cover - Assy 72-0072
340-047-603-0 Cover - Assy 72-0140
Field rework
340-047-605-0 Cover - Assy 72-0564
340-047-802-0 Pad Assy - Drive Starter Baseline
340-047-804-0 P a dA s s y-D r i v eS t a r t e r 72-0564
335-310-200-0 Spool 72-0564
340-155-304-0 Seal Assy - Oil 72-0564
340-091-109-0 Bracket Assy 72-0316
340-091-111-0 Bracket Assy 72-0564
340-206-001-0 Bracket 72-0564
340-199-801-0 Bracket 72-0564
340-199-901-0 Bracket 72-0564
340-200-002-0 Tube Assy -Drain 72-0564
October 13, 2009 CFM56-7B S/B 72-0564
Revision 3, May 25, 2011 PAGE 52

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
