# Continental Critical Service Bulletin 15-2: Revision C

- Rights: © Continental Aerospace Technologies, Inc. Filed by the FAA in regulations.gov docket FAA-2016-0069; AD 2016-21-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Continental Critical Service Bulletin 15-2](https://openairdocs.org/service-documents/continental/sb-15-2.md)
- Title as filed: CSB15-2C
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/82/bf/82bff2cba363924cdcaa3b3926ef97cc434d0781bba261e41f8f9e3664f3e917
- Page: https://openairdocs.org/service-documents/continental/sb-15-2/file/82bff2cba363

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

CONTINENTAL MOTORS® AIRCRAFT ENGINE  CATEGORY 2
CRITICAL SERVICE BULLETIN  CSB15-2C
SUPERSEDES CSB15-2B
COMPLIANCE NECESSARY TO MAINTAIN SAFETY  TECHNICAL PORTIONS
FAA APPROVED
SUBJECT:  Oil Cooler Cross Fitting Replacement
PURPOSE:  To replace oil cooler cross fitting (part numbers AN918-1J and AN918-2J)
with a new enhanced cross fitting (P/N. 658607).
COMPLIANCE: Within the next 25 hours of engine operation or the next scheduled inspection
or engine servicing, whichever occurs first.
MODELS
AFFECTED:  New and rebuilt TSIO550-C5, -C7, -C8, -C9, -C10, -C11, -C12, -C13, -C17, -
C18, -C19, -C20, -C21; TSIO550-N; TSIOF550-D; TSIOF550-K aviation •
gasoline (AvGas) engine models that use oil cooler cross fitting P/Ns AN918-1J
or AN918-2J with engine serial numbers prior to 1012296.
I. GENERAL INFORMATION
Continental Motors, Inc. (CMI) is aware of some occurrences where a loss of engine oil resulted
from a fractured nipple fitting between the cross fitting and the oil cooler. Design improvements
consolidate the oil cooler cross fitting stack-up into a single part, which significantly increases the
strength and provides a simplified procedure for installing the oil cooler cross fitting found on
specified TSIO-550 and TSIOF-550 engines. Modifications described herein on engine serial
numbers 1012296 and higher were accomplished at the factory.
WARNING
It is critical to follow ALL "Standard Practices" within your
Maintenance and Overhaul Manual when connecting fittings
and hoses.
II. BACKGROUND INFORMATION
CMI has made several design enhancements to the cross fitting configuration that provides
lubricating oil to the turbocharger bearings, and, in some cases, the oil pressure sensor.
Located in your M-18 (29 May 2015) or M-26 (15 September 2014), or later revision, •
Maintenance and Overhaul Manuals:
1. Chapter 17 provides detailed instructions on installing the pipe fittings found on the oil
cooler and the authorized pipe sealant to be used
2. Appendix B provides the "General Torque Specifications" to be used when tightening
the pipe fittings and B-nuts.
CAUTION: It is critical to follow Standard Practices to prevent
applying twisting or shear loads, or over torquing the mated fittings.
3. Appendix C provides specific instructions to properly support equipment during
installation of fittings and/or B-nuts (reference section C-12, "Hose and Tubing
Installation."
ISSUED  REVISED  PAGE NO  DOC NO  REVISION
2015/07/02  2015/11/09  1 of 6  CSB15-2
P.O. Box 90 Mobile, AL 251-436-8299
©2015 Continental Motors, Inc.

### Page 2 (OCR)

Design enhancements:
1. Eliminate the pipe bushing and nipple fitting stack-up (see Figure 1) typically found
between the cross fitting and the oil cooler and replaces them with a single cross fitting
(P/N 658607).
2. Provide a larger tool surface area on the cross fitting for support wrenches during
subsequent fitting and b-nut installation.
3. Added AN915-1J, 45-degree elbow fitting, to specific TSIO550-C engine models to
accommodate optional oil pressure sensor installation (similar orientation as
TSIOF550-D, sce Figure 2).
4. Remove the additional pipe bushings (P/N AS4861J01) used for the oil pressure sensor
and pipe plug previously installed on TSIO550-C20B and -C21B installations (see
Figure 1). These bushings are obsolete (for this application) and will no longer be
necessary for the new cross fitting installation; the AN915-1J 45-degree elbow fitting or
pipe plugs fit directly into the new cross fitting (see Figure 2).
Bushing, typ.
Pipe
= Bushings  Pipe  - Bushings
Nipple, typ.-
Cross, typ.
TSIO550-C, AS ENUMERATED  TSIO550-C20B  TSIO550-C21B
Bushing, typ.
Nipple, typ.
Cross, typ.
TSIO550-N  TSIOF550-D  TSIOF550-K
Figure 1. Cross Fitting Stack-Up, Prior Configurations
ISSUED  REVISED  PAGE NO  DOC NO  REVISION
2015/07/02  2015/11/09  2 of 6  CSB15-2
P.O. Box 90 Mobile, AL 251-436-8299

### Page 3 (OCR)

Elbow-  Elbow-  - Plug
Plug
Sensor,  Sensor,
Oil Press.  Oil Press /
Cross
Fitting  Cross  - Plug  Fitting  Cross  - Plug  Fitting
Flared  Flared
- Elbow
Nipple  Nipple
TSIO550-C & N  TSIOF550-D  TSIOF550-K
Figure 2. Cross Fitting, NEW Configurations
III. ACTION REQUIRED
REMOVE AND REPLACE the superseded parts with new cross fitting (P/N 658607) using the
same procedures located in your M-18 or M-26 Maintenance and Overhaul Manuals. Reference the
latest revision of the CMI Illustrated Parts Catalog (IPC) to determine applicable additional
connectors, elbows, or plug part numbers and adjust the instructions accordingly.
OLD FITTING  NEW FITTING
AN918-1J, AN918-2J  658607
Figure 3. Cross Fitting, Comparison
WARNING
Use eye protection when cutting safety wire to prevent eye
injury.
1. Remove and discard safety wire securing vernatherm to oil cooler pipe bushing.
2. Follow the detailed instructions for removing and installing pipe fittings found on oil
coolers (Chapter 17-6) using sealant specified.
3. Use a minimum 10X magnifying lens to visually inspect outboard port threads at the aft
side of the oil cooler for contamination, distortion, or damage before installing new
cross fitting (P/N 658607).
a. If determined serviceable, continue installing new cross fitting.
b. If there is evidence of contamination or damage, please contact Continental Motors
Customer Service Department directly at 1(800) 326-0089.
ISSUED  REVISED  PAGE NO  DOC NO  REVISION
2015/07/02  2015/11/09  3 of 6  CSB15-2  C
P.O. Box 90 Mobile, AL 251-436-8299

### Page 4 (OCR)

4. Reference Appendix B, "General Torque Specifications" for torque pipe fitting
installation instructions (NPTF threads):
a. Screw the cross fitting (P/N 658607) into the outboard port (at the aft side of the oil
cooler) to the finger tight position.
b. Wrench tighten the cross fitting to the appropriate clocking of fitting within 1-3
turns from the finger tight position. Minimum torque of 185 in/Ibs must be achieved
upon clocking position of fitting.
NOTE: The fitting is not to be loosened in order to achieve proper alignment
(clocking). Torque values specified are for reference only. Torque values must
be used on other pipe fittings or plugs where clocking is not required.
5. Reference Appendix C, "Hose and Tubing Installation' when installing fittings and/or
B-nuts.
CAUTION: It is critical to support pipe fittings and follow Standard
Practices to prevent applying twisting or shear loads, ar over
torquing the mated fittings.
a. Use a wrench on both mating connections to avoid applying excessive torque to the
fittings. Securely tighten fittings and torque to the specified value in Appendix B.
Torque the hose or tubing end fitting while maintaining sufficient force on adjacent
fittings to prevent twisting and shear loads.
CAUTION: Do not exceed specified torque values.
b. Support the last fitting in the assembly on components that contain multiple fittings
coupled in one location (see Figure 4). DO NOT over-torque fittings.
Fitting to be
"Clocked"
Support Fitting with
Cross Fitting  Open End Wrench
Figure 4. Hose and Tube Installation Support
6. Install new safety wire securing vernatherm to cross fitting. Reference Appendix C-4,
"Safety Wire Hardware" to properly secure hardware.
ISSUED  REVISED  PAGE NO  DOC NO  REVISION
2015/07/02  2015/11/09  4 of 6  CSB15-2
P.O. Box 90 Mobile, AL 251-436-8299

### Page 5 (OCR)

7. Conduct a normal engine start and ground run-up according to your Airplane Flight
Manual / Pilot's Operating Handbook (AFM/POH) provided by the airframe manufacturer.
8. Perform a visual leak check of the serviced area, after shut-down, prior to placing
aircraft in service.
9. Make appropriate logbook entries detailing compliance actions taken in accordance
with this Critical Service Bulletin (CSB15-2). The logbook entry must include a
complete listing of parts used in this installation.
10. Return aircraft to service.
IV. WARRANTY
This Critical Service Bulletin is your authorization to perform the required inspection, replace the
affected parts), and receive warranty reimbursement, limited to the "Models Affected" and
compliance action required as defined within. Contact your authorized Continental Motors
distributor for warranty claim application and parts return instructions.
Contact Continental Motors Technical Services at one of the numbers listed below if you have
any questions concerning the technical content of this Critical Service Bulletin.
1.888.826.5465  toll free in United States
+1.251.436.8299  international callers
+1.305.964.0872  en Español
NOTE: Visit the Continental Motors web site at
www.contincntalmotors.acro to obtain copies of Continental
Motors Warranty Policies.
A. Allowances/Reimbursements
Table 1. Labor allowance shall be:
Labor
Allowance
Scope of Work  (hr)
Remove and replace superseded parts.  1.0
B. Illustrated Parts Catalog Instructions
Replacement parts required to comply with this bulletin are published in the illustrated
parts catalogs on the Continental Motors web site and may be ordered through any
authorized Continental Motors distributor.
NOTE: To find an authorized Continental Motors distributor,
follow  this  link:  http://www.continentalmotors.aero/
Support Materials/Authorized_Distributor_Listing!
ISSUED  REVISED  PAGE NO  DOC NO  REVISION
2015/07/02  2015/11/09  5 of 6  CSB15-2
P.O. Box 90 Mobile, AL 251-436-8299

### Page 6 (OCR)

Intentionally Left Blank
ISSUED  REVISED  ON TO
2015/07/02  2015/11/09  9 10 9
P.O. Box 90 Mobile, AL 251-436-8299

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
