# Daher Mandatory Service Bulletin 150-32: Revision 4

- Rights: © Socata. Filed by the FAA in regulations.gov docket FAA-2024-1480, the docket of AD 2024-19-09. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Daher Mandatory Service Bulletin 150-32](https://openairdocs.org/service-documents/daher/sb-150-32.md)
- Title as filed: Daher Service Bulletin SB 150-32 Revision 4
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/bb/c0/bbc05c987c12d9a82977535be61a0aae948ba1f1af43b3186aa85d5fc05db208
- Page: https://openairdocs.org/service-documents/daher/sb-150-32/file/bbc05c987c12

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
REVISION 1
SUBJECT: NOSE LANDING GEAR - WHEEL AXLE
CAUTION
 
PUBLICATION OF THIS SERVICE BULLETIN CANCELS AND REPLACES
PREVIOUS REVISIONS.
REPLACE THE EXISTING COPY OF THE SERVICE BULLETIN WITH THIS SERVICE
BULLETIN VERSION. THE SUPERSEDED COPY SHOULD BE DESTROYED.
NOTE:
A black bar in the left margin indicates a change in that line of text or figure .
REFERENCE DOCUMENT: 
Modification No. MOD80-0160-32 Version A
EFFECTIVITY: All MS880B, MS880B­D, MS881, MS883, MS884, MS885, MS886, MS887, MS890A,
MS890B, MS892A150, MS892B150, MS892E150, MS892E­D150, MS893A, MS893B,
MS893E, MS893E­D, MS894A, MS894E, Rallye 100S, Rallye 100S­D, Rallye 100ST ,
Rallye 100ST­D, Rallye 110ST , Rallye 150ST , Rallye 150ST ­D, Rallye 150T , Rallye 150T ­D,
Rallye 150SV, Rallye 150SVS, Rallye 180T , Rallye 180TS, Rallye 180T ­D, Rallye 235A, Rallye
235F , Rallye 235E, Rallye 235E­D aircraft.
NOTE:
If an aircraft covered in the effectivity has a modification or repair that is not of Daher Aerospace
origin, and which affects the content of this Service Bulletin, the operator is responsible for
obtaining approval by the appropriate airworthiness authority for an adaptation before the
incorporation of the Service Bulletin.
PURPOSE: Reduce the possibility of fatigue failure in the nose gear wheel axle.
PURPOSE OF REVISION 3: 
- To reduce inspection interval from 500 hours to 200 hours.
- To add an inspection between axle radius and nose landing gear fork.
- To add Item 7 on the Figure 1.
- To take into account second-hand nose landing gears and second-hand wheel axles.
SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Daher Aerospace
Customer Support
Airplane Division Phone: 33 (0)5 62.41.73.00
65921 Tarbes Cedex 9 tbmcare@daher .com
France

### Page 2

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 2 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
PURPOSE OF REVISION 4: 
- To propose nose gear wheel axle new design as a terminative solution.
- To add a flowchart in order to clarify the process to be applied.
- Dye penetrant inspection becomes a magnetic particle inspection.
NOTE:
The Service Bulletin incorporates a new form of presentation and new wording.
SUMMARY:
A. PREPARATION
B. INSPECTION
C. NOSE GEAR WHEEL AXLE REPLACEMENT
D. RECONDITIONING
APPLICATION:
Refer to the following flowchart:
NOTE:
In case of replacement of nose landing gear or nose gear wheel axle (8) with a second-hand
part: apply Paragraph B.: “INSPECTION” and replace the 4 attaching screws (6) before the
first flight.
NOTE:
To replace the 4 attaching screws (6), every 2,000 hours.

### Page 3

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 3 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
Stop the AD/SB
application ?
Replace nose gear
wheel axle by new
design axle + replace
the 4 attaching screws
(Paragraph C.)
Perform a visual
inspection on defined
zone (Paragraph B.)
YES
NO
 
Next 50h
and every
200h
Crack detected ?
Perform a magnetic
particle inspection on
defined zone
(Paragraph B.)
Crack detected ?
End of the AD/SB
application
NO
NO
YES
YES

### Page 4

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 4 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
WARRANTY:
Not applicable
OPERATIONAL CONSEQUENCES / TRAINING:
Not applicable
SERVICING CONSEQUENCES:
No changes to the scheduled maintenance
PROCURABLE MATERIAL:
If nose gear wheel axle is replaced:
Item Figure Part Number Description Qty/aircraft
/ / AV-RAL-032 Front wheel axle assembly 1
1 1 5401458376 Locknut(P/N ISO10511-M8-05-B9G) 4
6 1 5101231508 Screw (P/N 5030308375) 4
NOTE:
P/N AV-RAL-032 is composed of the nose gear wheel axle (P/N AV-RAL-001-01) (Item 4)
and the spacer (P/N AV-RAL-002-01) (Item 5).
CONSUMABLE MATERIAL or OTHER PRODUCTS (Local purchase):
- Grease AIR 4210A (MIL-G-23827A)
TOOLS:
- Standard aeronautical maintenance station tools
- Magnetic particle inspection tools
AFFECTED PUBLICATIONS:
IPC Chapters:
- 4.3.0
- 4.3.1
- 4.3.2
AMM Chapter:
- 2.5.1
CMM: Not applicable
POH: Not impacted
RELATED DOCUMENTS: Document(s) necessary for application of the procedure(s)
None

### Page 5

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 5 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
ASSOCIATED DOCUMENTS: 
None
MANPOWER:
If no replacement of nose gear wheel axle:
Application
During a scheduled inspection 1 aeronautical mechanic: 1 hour
1 magnetic particle inspection-certified
operator for crack detection: 1 hour
Out of a scheduled inspection 1 aeronautical mechanic: 2 hours
1 magnetic particle inspection-certified
operator for crack detection: 1 hour
For a new nose gear wheel axle installation:
Application
During a scheduled inspection 1 aeronautical mechanic: 1 hour
Out of a scheduled inspection 1 aeronautical mechanic: 2 hours
NOTE:
The manpower estimates given in this Service Bulletin assume that the work will be done by
Service Centers having previous experience with the aircraft type and with the procedures
involved.
TECHNICAL INCIDENCES:
- None
PARTS TO BE RE-IDENTIFIED:
YES /C0111 NO /C0084
DESCRIPTION OF ACCOMPLISHMENT INSTRUCTIONS :
WARNING
 
MAKE SURE TO OBEY ALL THE WARNINGS AND CAUTIONS INCLUDED IN THE
REFERENCED PROCEDURES.
NOTE:
Operations required in this Service Bulletin must be performed by persons authorized by the
appropriate airworthiness authority.
A. PREPARATION – See Figure 1
1) Install the airplane on jacks - refer to Chapter 2.5.1 of the Maintenance Manual.
2) Remove the nose gear wheel fairing (if installed).
3) Remove the nose gear wheel.
4) Remove the nose gear wheel axle (8), retain the 4 attaching screws (6),
the 4 washers (2) and the spacer (7) (if installed); discard the locknuts (1).

### Page 6

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 6 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
If you want to continue the adherence to the AD/SB application:
5) Apply Paragraph B.: “INSPECTION”.
If you want to eliminate the need to adhere to the AD and to apply the repetitive Service
Bulletin by the replacement of the nose gear wheel axle:
5) Apply Paragraph C.: “NOSE GEAR WHEEL AXLE REPLACEMENT”.
B. INSPECTION – See Figure 1
1) Clean the wheel and the axle.
2) Perform a detailed visual inspection of the area 1 (9) to look for evidence of chafing
between the wheel bearing and axle surface.
If a crack is detected during the detailed visual inspection:
3) Apply Paragraph C.: “NOSE GEAR WHEEL AXLE REPLACEMENT”.
If no crack is detected during the detailed visual inspection:
3) Perform a magnetic particle inspection on nose wheel axle. Check for absence of
distortion and nicks or wear.
If a crack is detected:
4) Apply Paragraph C.: “NOSE GEAR WHEEL AXLE REPLACEMENT”.
If no crack is detected:
4) Check the 4 attaching screws (6) for condition, check for absence of distortion,
scratches and nick or wear. Change screws if necessary .
NOTE:
The 4 attaching screws (6) must be replaced by new ones every 2,000 hours.
CAUTION
 
THE NOSE GEAR WHEEL AXLE (8) P/N 895.42.0.027.0 MUST BE INSTALLED WITH
THE SPACER (7).
5) Attach the nose gear wheel axle (8) on the landing gear (3) with the 4 attaching
screws (6), 4 washers (2), and (if installed), the spacer (7) and the 4 new locknuts (1).
6) Lightly coat the axle contacts and the wheel bearings with AIR 4210B
(MIL-G-23827A) grease.
7) Perform the reconditioning in accordance with Paragraph D.
C. NOSE GEAR WHEEL AXLE REPLACEMENT – See Figure 1
1) Discard the removed nose gear wheel axle (8), the spacer (7) and the 4 attaching
screws (6).
CAUTION
 
THE NEW NOSE GEAR WHEEL AXLE (4) MUST BE INSTALLED WITH THE SPACER
(5).
2) Attach the new nose gear wheel axle (4) on the landing gear (3) with the 4 new
attaching screws (6), 4 washers (2), the spacer (5) and the 4 new locknuts (1).

### Page 7

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 7 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
NOTE:
The 4 attaching screws (6) must be replaced by new ones every 2,000 hours.
3) Lightly coat the axle contacts and the wheel bearings with AIR 4210B
(MIL-G-23827A) grease.
4) Perform the reconditioning in accordance with Paragraph D.
D. RECONDITIONING – See Figure 1
1) Install the nose gear wheel.
2) Install the nose gear wheel fairing (if necessary).
3) Check nose gear wheel for free rotation.
4) Set the airplane on its wheels again.
DOCUMENTATION:
Upon completion of this Service Bulletin, make an appropriate maintenance record entry as
described hereunder:
If the nose gear wheel axle has not been replaced:
- SB150-32 Rev 4 “NOSE LANDING GEAR - WHEEL AXLE”
If the nose gear wheel axle has been replaced by the new design one
(P/N AV-RAL-001-01):
- SB150-32 Rev 4 “NOSE LANDING GEAR - WHEEL AXLE” and Modification
No. MOD80-0160-32 Version A
WARNING: Daher Aerospace considers that it is MANDATORY for operators to comply with the
instructions of this Service Bulletin.
Owners/operators who do not follow the compliance indicated in this Service Bulletin do so
at their own risk.

### Page 8

SERVICE BULLETIN
RALLYE AIRCRAFT
MANDATORY
The technical content of this document is approved
under the authority of the DOA ref EASA.21J.013
and is the subject to an AD
SB 150
REVISION 4
32
 ATA No.
Page 8 / 8JUN 91
Rev. 4 - JAN 23
This document is the property of Daher Aerospace. Reproduction prohibited without prior Daher Aerospace agreement.
Figure 1 - Wheel axle
1 - Locknut
2 - Washer
3 - Landing gear
4 - New nose gear wheel axle
5 - Spacer
6 - Attaching screw
7 - Spacer
8 - Nose gear wheel axle
9 - Area 1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.