# Daher Mandatory Service Bulletin 70-104: Revision 4

- Rights: © Socata. Filed by the FAA in regulations.gov docket FAA-2025-2265; AD 2025-26-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Daher Mandatory Service Bulletin 70-104](https://openairdocs.org/service-documents/daher/sb-70-104.md)
- Title as filed: DAHER AEROSPACE TBM Aircraft Mandatory Service Bulletin No. SB 70-104_Revision 4_dated December 2018
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/0c/37/0c3771956dca69585d70cacd566bb3dc6d09951dbc654117cfa10f7cf76a047a
- Page: https://openairdocs.org/service-documents/daher/sb-70-104/file/0c3771956dca

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
CAUTION 
SCHEDULED APPLICATION OF THIS SERVICE BULLETIN CAN BE STOPPED BY
SB70--255--55 TERMINATIVE APPLICATION. 
SUBJECT : INSPECTIONOFTHE VERTICALSTABILIZER ATTACHMENT FITTING S 
EFFECTIVITY : TBM 700 aircraft S/N1 to308, plusS/N310 which have not applied SB70---255---55.
NOTE :
From aircraft S/N 297, the modification No. MOD70---127---55 is applied at the factory.
From aircraft S/N311, plus S/N309, themodification No. MOD70---129---53 is applied at the 
factory.
REASON :
A. PROBLEM 
Cracks on a verticalstabilizer attachment fitting.
B. REASON 
Corrosion on the verticalstabilizer attachment fittings.
C. SOLUTION 
Inspection of the fittings and boltsand protection reinforcement.
PURPOSE OF THE REVISION 1 :
Closing of effectivityand addition ofNote.
PURPOSE OF THE REVISION 2 :
AdditionofnewPartNumbersforexpandableboltsandofasso ciatedprocedurerelatedto 
Modification No. MOD 70---0205---55.
Addition of the possibilitytouse anequivalent process forcrack detection.
PURPOSE OF THE REVISION 3 :
Use of an endoscope toinspect thefittings.
Modification of the NOTE due tothefact that SB was not taken intoaccount in Chapter05 
of the Maintenance Manualat the Revision dated JUL07.
PURPOSE OF THE REVISION 4 :
Tomodifylogo.
Topropose SB70---255---55 application as a terminative solution.
To replace expandable bolts assy (rear and front) on each installation in accordance with 
Maintenance Manual.
SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
DAHER AEROSPACE 
Direction des Services TELEPHONE:33(0)562.41.73.00 
65921TARBESCEDEX9 tbmcare@daher.com 
FRANCE

### Page 2

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 2 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
SUMMARY :
A. INSPECTIONOFTHE FITTINGSAND BOLTS 
B. PROTECTIONREINFORCEMENT 
APPLICATION : During the next 600---hrs scheduled inspection, then every 1200 hrs or every 2 annual
inspections.
PROCURABLE MATERIAL :
--- Parts tobe ordered from your TBM spare parts distributor.
Item Part number Description Qty/aircraft 
1 Pre---MOD70---0205---55
7018814671 
After stock depletion,
replaced by 
Expandablebolt assy(rear) 2
Post---MOD 70---0205---55
7022810298 
6 Pre---MOD70---0205---55
7018814661 
After stock depletion,
replaced by 
Expandablebolt assy(front) 2
Post---MOD70---0205---55
7022810299 
After stock depletion,
replaced by 
NOTE :
The difference between Pre---MOD 70---0205---55 and Post---MOD 70---0205---55 bolts is 
identified on details A and B of Figure 1. 
CONSUMABLE MATERIAL or OTHER PRODUCTS (Localpurchase):
--- Stepladder 5 ft (1.50 m) 
--- Mastinox6856KD (MIL---P---8116 D) 
--- WADIS 24 (MIL---C---16173 D grade 3) or LPS 3 (DA---4---653---40) or ARDROX 3140 
(MIL---C---16173 D grade 2) 
TOOLS :
--- Standard aeronauticalmaintenance station tools 
--- Torque wrench 0 --- 90 lbf.in (0 --- 10 N.m) 
--- Endoscope 
MANPOWER :
--- 1 aeronauticalmechanic :3.50 hrs

### Page 3

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 3 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
TECHNICAL INCIDENCES :
--- None 
DESCRIPTION OF ACCOMPLISHMENT INSTRUCTIONS :
NOTE :
Operations required in this ServiceBulletin must beaccomplished bypersons authorizedby 
their Airworthiness Authorities and according to the procedure described hereafter.
A. INSPECTIONOFTHE FITTINGSAND BOLTS --- see Figures 1, 2 and 3
1) Position the stepladder at thefront ofthe verticalstabilizer.
2) Openaccesspanel311andremovethedorsalfin --- referto Chapter 55---30---00of
the Maintenance Manual.
3) Remove and discard cotter pins (2) and (10). Loosen nuts (3) and (9), but do not
remove them.
4) On the L.H. side then on the R.H. side of the front fitting, perform the following 
operations :
Pre---MOD 70---0205---55 --- see Figure 1, DetailA
a) Remove nut and discard (9), washer (8)and spring washers (7).
b) Remove and discard expandable bolt (6).
Post---MOD 70---0205---55 --- see Figure 1, DetailB
a) Remove and discard nut(9), washer (8).
b) Remove and discard expandable bolt (6).
All
CAUTION 
MIXING BETWEEN BOLTS INSTALLED ON L.H. OR R.H. SIDE IS PROHIBITED.
MIXING BETWEEN BOLTS INSTALLED AT THE FRONT OR AT THE REAR IS 
PERMITTED 
c) With an endoscope, check for corrosion on the fitting.
d) Apply a thin coat of Mastinox 6856KD (MIL---P---8116 D) onnew expandable 
bolt (6).
Pre---MOD 70---0205---55 --- see Figure 1, DetailA
e) IncompliancewithFigure2,installnewexpandablebolt( 6),springwashers(7),
washer (8)and nut (9). Donot tighten.
Post---MOD 70---0205---55 --- see Figure 1, DetailB
e) IncompliancewithFigure3,installnewexpandablebolt( 6),washer(8)andnut
(9). Donot tighten.
5) On the L.H. side then on the R.H. side of the rear fitting, perform the following 
operations :

### Page 4

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 4 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
Pre---MOD 70---0205---55 --- see Figure 1, DetailA
a) Remove and discard nut (3), washer (4)and spring washers (5).
b) Remove and discard expandablebolt (1).
Post---MOD 70---0205---55 --- see Figure 1, DetailB
a) Remove and discard nut (3)and washer (4).
b) Remove and discard expandablebolt (1).
All
c) With an endoscope, check for corrosion on the fitting.
d) Performacrackdetectionbypenetrantinspection --- ref ertoChapter20---50---01
oftheMaintenanceManual,oranyotherequivalentprocess( Eddycurrent...)on 
the bores of the verticalstabilizer fittingand attachments.
e) Apply a thin coat of Mastinox 6856KD (MIL---P---8116 D) onnew expandable 
bolt (1).
Pre---MOD 70---0205---55 --- see Figure 1, DetailA
f) IncompliancewithFigure2,installnewexpandablebolt( 1),springwashers(5),
washer (4)and nut (3). Donot tighten.
NOTE :
Itispossibletoreinstalltheboltwithheaddirectedtothe exteriorinordertotorque 
the bolt easier.
Post---MOD 70---0205---55 --- see Figure 1, DetailB
f) IncompliancewithFigure3,installnewexpandablebolt( 1),washer(4)andnut
(3).Donottighten --- refertoChapter55---30---00,Page4 01oftheMaintenance 
Manual.
NOTE :
Itispossibletoreinstalltheboltwithheaddirectedtothe exteriorinordertotorque 
the bolt easier.
6) If exfoliation corrosion is detected, transmit a report with photos or drawings to 
DAHER sothat a repair solution is worked out.
7) If pitting corrosion is detected, refer to Chapter 20---40---01 of the Maintenance 
Manual.
8) Using a torque wrench, torque nuts (3)to62 --- 71 lbf.in (7--- 8 N.m).
9) If necessary, screw toalign the notches ofnuts (3)with the first pin hole.
10) Safetywith new cotter pin (2)supplied with bolt.
11) Using a torque wrench, torque nuts (9)to53 lbf.in (6 N.m).
12) If necessary, screw toalign the notches ofnuts (9)with the first pin hole.
13) Safetywith new cotter pin (10)supplied with bolt.
14) Perform protection reinforcement --- refertoParagraph B.

### Page 5

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 5 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
B. PROTECTIONREINFORCEMENT 
1) ApplyacoatofWADIS24(MIL---C---16173Dgrade3)orLPS3 (DA---4---653---40)or 
ARDROX3140(MIL---C---16173Dgrade2)onthefrontandrear fittingparts andon 
the bolts and washers.
UPDATING OF THE AIRCRAFT DOCUMENTATION :
UponcompletionofServiceBulletinNo.SB70---104---55,R evision4”INSPECTIONOFTHE 
VERTICAL STABILIZER ATTACHMENT FITTINGS”, make an appropriate maintenance 
record entry.
WARNING : DAHER AEROSPACE considers that it is MANDATORY for operators to comply with the 
instructions of this SB.
Operatorswhoarbitrarilyignorethecompliancestatement indicatedinthisSBdosoattheir 
own risk.

### Page 6

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 6 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
Figure 1 --- Identificationofbolts

### Page 7

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY 
The technicalcontent ofthis document is approved 
under the authorityofDOA No. EASA.21J.013 
is the subject ofan AD 
SB 70--104
REVISION 4
55 
ATANo.
Page 7 / 8JUN03 
Rev. 4 --- DEC 18 
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement 
Figure 2 --- Inspection offittings and bolts 
Pre---MOD70---0205---55
1 --- Expandable bolt
2 --- Cotter pin 
3 --- Nut
4 --- Washer 
5 --- Spring washer 
6 --- Expandable bolt
7 --- Spring washer 
8 --- Washer 
9 --- Nut
10 --- Cotter pin

### Page 8 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70 - 104  REVISION 4  55  ATA No.
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
1 - Expandable bolt
2 - Cotter pin
3 - Nut
4 - Washer
6 - Expandable bolt
8 - Washer
9 - Nut
10 - Cotter pin
4553000AAABMA14600  10
Figure 3 - Inspection of fittings and bolts
Post-MOD 70-0205-55
JUN 03  Page 8 / 8
Rev. 4 - DEC 18
This document is the property of DAHER AEROSPACE. Reproduction prohibited without prior DAHER AEROSPACE agreement

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
