# Daher Mandatory Service Bulletin 70-104: Revision 4

- Rights: © Socata. Filed by the FAA in regulations.gov docket FAA-2025-2265; AD 2025-26-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Daher Mandatory Service Bulletin 70-104](https://openairdocs.org/service-documents/daher/sb-70-104.md)
- Title as filed: EADS SOCATA TBM Aircraft Mandatory Service Bulletin No. SB 70-104_Amendment 1_dated August 2004
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/1d/15/1d15ee4a05dd5d76c7c0b11cfa106389af7d78f79acddd7f6abd7cf65c435aa1
- Page: https://openairdocs.org/service-documents/daher/sb-70-104/file/1d15ee4a05dd

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

EADS
SOCATA
EADS SOCATA
Direction des Services  TELEPHONE: 33 (0)5 62.41.73.00
65921 TARBES CEDEX 9  TELEFAX: 33 (0)5 62.41.76.54
FRANCE  TELEX :  532 835 F
TBM AIRCRAFT
SERVICE BULLETIN  SB 70-104  AMENDMENT 1  55  ATA No.
MANDATORY
DOA EASA.21J.013 Approved
SUBJECT  : INSPECTION OF THE VERTICAL STABILIZER ATTACHMENT FITTINGS
EFFECTIVITY : TBM 700 aircraft S/N 1 to 308, plus S/N 310.
NOTE :
From aircraft S/N 297, the modification No. MOD70-127-55 is applied at the factory.
From aircraft S/N 311, plus S/N 309, the modification No. MOD70- 129-53 is applied at the
factory.
REASON
A. PROBLEM
Cracks on a vertical stabilizer attachment fitting.
B. REASON
Corrosion on the vertical stabilizer attachment fittings.
C. SOLUTION
Inspection of the fittings and bolts and protection reinforcement.
REASON OF AMENDMENT 1 :
Closing of effectivity and addition of Note.
SUMMARY
A. INSPECTION OF THE FITTINGS AND BOLTS
B. PROTECTION REINFORCEMENT
COMPLIANCE: During the next 600-hrs scheduled inspection, then every 1200 hrs or every 2 annual
inspections.
PROCURABLE MATERIAL :
- Parts to be ordered, if necessary from your TBM spare parts distributor.
Item  Part number  Description  Qty/aircraft
Z00.N7018814671  Expandable bolt (rear)  2
2  Z00.N5787461153  Cotter pin  2
Z00.N5408455080  Nut  2
4  Z00.N7743819000  Washer  2
5  Z00.N7743819002  Spring washer  4
6  200.N7018814661  Expandable bolt (front)  2
JUN 03  Page 1 / 5
Amdt. 1 - AUG 04

### Page 2 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-104  AMENDMENT 1  55  ATA No
MANDATORY
DOA EASA.21J.013 Approved
Item  Part number  Description  Qty/aircraft
7  Z00.N7743819003  Spring washer  4
8  Z00. N7743810100  Washer  2
9  Z00.N5408455060  Nut  2
10  Z00.N5787461151  Cotter pin  2
CONSUMABLE MATERIAL (Local purchase) :
- Stepladder 5 ft (1.50 m)
- Mastinox 6856KD (MIL-P-8116 D)
- WADIS 24 (MIL-C-16173 D grade 3) or LPS 3 (DA-4-653-40) or ARDROX 3140
(MIL-C-16173 D grade 2)
TOOLING
- Standard aeronautical maintenance station tools
- Torque wrench 0 - 90 Ibf.in (0 - 10 N.m)
MANPOWER
- 1 aeronautical mechanic : 3.50 hrs
TECHNICAL INCIDENCES :
- None
ACCOMPLISHMENT INSTRUCTIONS :
NOTE :
Operations required in this Service Bulletin must be accomplished by persons authorized by
their Airworthiness Authorities and according to the procedure described hereafter.
A. INSPECTION OF THE FITTINGS AND BOLTS - see Figure 1
1) Position the stepladder at the front of the vertical stabilizer.
2) Open access panel 311 and remove the dorsal fin - refer to Chapter 55-30-00 of
the Maintenance Manual.
3) Remove and discard cotter pins (2) and (10). Loosen nuts (3) and (9), but do not
remove them.
4) On the L.H. side then on the R.H. side of the front fitting, perform the following
operations :
a) Remove nut (9), washer (8) and spring washers (7).
b) Remove expandable bolt (6).
c) Inspect the removed parts. The parts which do not meet the criteria as below will
be replaced and returned to SOCATA for analysis:
- bolt body, no corrosion mark,
- bolt head, nut, washer and spring washers, light pittings accepted.
d) Check for corrosion on the fitting.
JUN 03  Page 2 / 5
Amdt. 1 - AUG 04

### Page 3 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-104  AMENDMENT 1  55  ATA No.
MANDATORY
DOA EASA.21J.013 Approved
e) Apply a thin coat of Mastinox 6856KD (MIL-P-8116 D) on expandable bolt (6).
f) Install expandable bolt (6), spring washers (7), washer (8) and nut (9). Do not
tighten.
5) On the L.H. side then on the R.H. side of the rear fitting, perform the following
operations :
a) Remove nut (3), washer (4) and spring washers (5).
b) Remove expandable bolt (1).
c) Inspect the removed parts. The parts which do not meet the criteria as below will
be replaced and returned to SOCATA for analysis:
- bolt body, no corrosion mark,
- bolt head, nut, washer and spring washers, light pittings accepted.
d) Check for corrosion on the fitting.
e) Perform a penetrant inspection on the bores of the vertical stabilizer fitting and
attachments - refer to Chapter 20-50-01 of the Maintenance Manual.
f) Apply a thin coat of Mastinox 6856KD (MIL-P-8116 D) on expandable bolt (1).
g) Install expandable bolt (1), spring washers (5), washer (4) and nut (3). Do not
tighten.
NOTE :
It is possible to reinstall the bolt with head directed to the exterior in order to torque
the bolt easier.
6) If exfoliation corrosion is detected, transmit a report with photos or drawings to
SOCATA so that a repair solution is worked out.
7) If pitting corrosion is detected, refer to Chapter 20-40-01 of the Maintenance
Manual.
8) Using a torque wrench, torque nuts (3) to 62 - 71 Ibf.in (7 - 8 N.m).
9) If necessary, screw to align the notches of nuts (3) with the first pin hole and safety
with a new cotter pin (2).
10) Using a torque wrench, torque nuts (9) to 53 Ibf.in (6 N.m).
11) If necessary, screw to align the notches of nuts (9) with the first pin hole and safety
with a new cotter pin (10).
12) After application of this SB, please return the enclosed form to SOCATA at the
indicated address.
B. PROTECTION REINFORCEMENT
1) Apply a coat of WADIS 24 (MIL-C- 16173 D grade 3) or LPS 3 (DA-4-653-40) or
ARDROX 3140 (MIL-C-16173 D grade 2) on the front and rear fitting parts and on
the bolts and washers.
UPDATING OF THE AIRCRAFT DOCUMENTATION:
Mention, in the aircraft log book, the application of Service Bulletin No. SB 70-104-55
"INSPECTION OF THE VERTICAL STABILIZER ATTACHMENT FITTINGS".
JUN 03  Page 3 / 5
Amdt. 1 - AUG 04

### Page 4 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-104  AMENDMENT 1  55  ATA No.
MANDATORY
DOA EASA.21J.013 Approved
WARNING :  SOCATA considers that it is MANDATORY for operators to comply with the instructions of
this SB.
Operators who arbitrarily ignore the compliance statement indicated in this SB do so at their
own risk.
JUN 03  Page 4 / 5
Amdt. 1 - AUG 04

### Page 5 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-104  AMENDMENT 1  55  ATA No.
MANDATORY
DOA EASA.21J.013 Approved
1 - Expandable bolt
2 - Cotter pin
3 - Nut
4 - Washer
5 - Spring washer
6 - Expandable bolt
7 - Spring washer
8 - Washer
9 - Nut
10 - Cotter pin
I4553000AAABMA4600  10
Figure 1 - Inspection of fittings and bolts
JUN 03  Page 5 / 5
Amdt. 1 - AUG 04

### Page 6

(No text on this page.)

### Page 7 (OCR)

EADS
SOCATA
FORM TO BE FILLED AFTER COMPLIANCE WITH SERVICE BULLETIN
TBM AIRCRAFT
SERVICE BULLETIN  SB 70 - 104  55
AMENDMENT 1  ATA No.
INSPECTION OF THE VERTICAL STABILIZER ATTACHMENT FITTINGS
I, the undersigned,  certity
that service bulletin No. SB 70-104-55 Amendment 1 has been complied with on aircraft
Front fitting  Rear fitting
Corrosion on fitting  L.H  R.H  L.H.  R.H.
Bolt and/or washer corrosion  L.H  R.H  L.H  R.H
Crack on fitting  L.H  R.H  L.H  R.H
1. Aircraft
Type  Serial No.  Registered
Flight hours  Number of landings
2. Owner
Name  Phone :  Fax
Address
E-mail :
3. User (if different from owner)
Name  Phone :  Fax
Address
E-mail :
4. Service center
Name :  Phone :  Fax :
Address
E-mail :
Approval No
5. Remarks
DATE :  SIGNED :
To be returned to SOCATA at the following address :
EADS SOCATA
Direction des Services
65921 TARBES CEDEX 9  Fax : 33 (0)5 62 41 76 54
FRANCE  Telex : 532 835 F

### Page 8

(No text on this page.)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
