# Daher Mandatory Service Bulletin 70-130: Revision 3

- Rights: © Socata. Filed by the FAA in regulations.gov docket FAA-2015-2047; AD 2015-17-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Daher Mandatory Service Bulletin 70-130](https://openairdocs.org/service-documents/daher/sb-70-130.md)
- Title as filed: SB 70-130 Revision 3
- Pages: 6
- PDF: https://openairdocs.org/files/sha256/33/4d/334da9f6994473b319b69a1e4ae312d1bd7832424c217c70506cce04824d708c
- Page: https://openairdocs.org/service-documents/daher/sb-70-130/file/334da9f69944

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

A DAHER-SOCATA
SOCATA
Direction des Services  TELEPHONE: 33 (0)5 62.41.73.00
65921 TARBES CEDEX 9  TELEFAX: 33 (0)5 62.41.76.54
FRANCE
TBM AIRCRAFT
SERVICE BULLETIN  SB 70-130  REVISION 3  32  ATA No
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
SUBJECT: "MAIN LANDING GEAR INSPECTION"
• EFFECTIVITY: TBM 700/850 aircraft S/N 1 to 638, 687 which main landing gear body P/Ns are different from
D68161 or D68161-1 (L.H. landing gear) and D68162 or D68162-1 (R.H. landing gear).
PURPOSE
A. PROBLEM
Cracks have been evidenced on main forging bodies during an overhaul.
B. ROOT CAUSE
Fatigue.
C. SOLUTION
Inspections and replacement, if necessary.
PURPOSE OF REVISION 1 :
- Closing of validity range
- Addition of Paragraph A. to check landing gear body P/N
- SB application form deleted
- Note deleted at Compliance Paragraph
- Logo modification
PURPOSE OF REVISION 2 :
- Increase of inspection interval from 175 landings to 240 landings
PURPOSE OF REVISION 3 :
- Modification of effectivity
- Addition of Terminating Solution paragraph
SUMMARY
A. CHECK OF LANDING GEAR BODY P/N
B. PREPARATION
C. CHECK
D. RECONDITIONING
E. TERMINATING SOLUTION
JAN 06  Page 1 / 6
Rev. 3 - DEC 14

### Page 2 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70- 130  REVISION 3  32  ATA No
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
APPLICATION:
For landing gear with forging body totalizing more than 1750 landings since new :
- Perform an inspection of forging body within 100 landings once this Service Bulletin is
issued, then repeat this inspection without exceeding 240 landings.
For landing gear with landing forging body totalizing more than 3500 landings since new :
- Perform an inspection of forging body within 25 landings once this Service Bulletin is
issued, then repeat this inspection without exceeding 240 landings.
For additional assistance, please go online at www.socata.com
PROCURABLE MATERIAL:
- Parts to be ordered from your TBM spare parts distributor.
Item  Part number  Description  Qty/aircraft
Z0O.N7323265025  Cotter pin E27487-25-22CAT  2
CONSUMABLE MATERIAL or OTHER PRODUCTS (Local purchase) :
- Alodine 1200 (MIL-C-5541 Class I/A or MIL-C-81706)
Primer ISOMAP P23 (BMS 1079) or equivalent
Finish paint AEROMAP 1000 (MIL-C-83289)
- Protective varnish :
• Green isolating varnish Ref. 1318B DUROUX
• Blue isolating varnish Ref. 7D 1586 + hardener Ref. 7D 1586 ASTRAL-PYROLAC
• Isolating varnish Ref. 43022 AKZO NOBEL + blue colorant Ref. 557506 VIRACOLOR
• or any other equivalent locally approved product.
TOOLS
- Standard aeronautical maintenance station tools
- Eddy current measurement bench
- Tools necessary for dye penetrant inspection or fluorescent penetrant inspection
MANPOWER :
- 1 aeronautical mechanic
- 1 Eddy current certified operator for crack detection, or
1 certified operator for dye penetrant inspection or fluorescent penetrant inspection
TECHNICAL INCIDENCES:
- None
JAN 06  Page 2 / 6
Rev. 3 - DEC 14

### Page 3 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-130  REVISION 3  32  ATA No.
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
DESCRIPTION OF ACCOMPLISHMENT INSTRUCTIONS:
NOTE :
Operations required in this Service Bulletin must be accomplished by persons authorized by
their Airworthiness Authorities and according to the procedure described hereafter.
A. CHECK OF LANDING GEAR BODY P/N - see Figure 1
1) On embossment (7), note main landing gear body P/N.
a) If P/N is D68161 or D68161-1 for L.H. landing gear and D68162 or D68162-1
for R.H. landing gear, this SB is not applicable to the aircraft.
b) If P/N is different, apply paragraphs B. thru D. on aircraft involved landing gear
(S).
B. PREPARATION - see Figure 1
1) Put the aircraft on jacks - refer to Chapter 07-10-00 of the Maintenance Manual.
2) Connect the ground power unit - refer to Chapter 24-40-00 of the Maintenance
Manual.
Disconnect L.H. and R.H. side door links - refer to Chapter 52-80-01 of the
Maintenance Manual.
WARNING
PRIOR TO ANY LANDING GEAR OPERATION, MAKE SURE THE LANDING GEAR
AREA IS CLEAR.
4) Retract landing gear.
With a second operator, at mid-travel, open "LDG GR" circuit breaker.
6) Set "SOURCE" selector to "OFF".
7) Install the warning sign prohibiting SOURCE" selector operation
WARNING
DO NOT OPERATE
MAINTENANCE WORK IN PROGRESS
8)  Remove tie-wraps securing electrical harness and bonding strap (1).
9) Remove and discard cotter pin (4).
10) Without removing it, unscrew nut (3) in order to disengage attaching lug (2) of the
bonding strap during crack detection.
11) Perform steps 8) thru 10) on the other landing gear.
C. CHECK - see Figure 1
NOTE :
Crack detection can either be performed by Eddy current or by dye penetrant inspection
or by fluorescent penetrant inspection.
JAN 06  Page 3 / 6
Rev. 3 - DEC 14

### Page 4 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-130  REVISION 3  32  ATA No.
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
Detection by Eddy current
1) On a flat area, close to the described area (6) of Figure 1, calibrate the measurement
bench.
2) As per the described area (6) of Figure 1, for about 1.96 in (5 cm) in length, perform
the crack detection on the landing gear leg by Eddy current with special emphasis
on the bending radius (5) as per the described area (6) of Figure 1.
Dye penetrant inspection or fluorescent penetrant inspection
1) Perform a chemical etching of the area as per the described area (6) of Figure 1.
2) As per the described area (6) of Figure 1, for about 1.96 in (5 cm) in length, perform
the crack detection on the landing gear leg by dye penetrant inspection or
per the described area (6) of Figure 1- refer to Chapter 20-50-01 of the
Maintenance Manual.
All
3) If no crack is detected :
a) Protect bare metal with Alodine 1200 and a coat of primer paint, as required.
b) Perform paint touch-up, as required.
NOTE :
As an alternative process to protect bare metal, protective varnish as listed in
"CONSUMABLE MATERIAL" paragraph or any equivalent locally approved
protect a sed do ine  product may be used to facilitate further repetitive dye penetrant inspections or
c) Torque nut (3) - refer to Chapter 32-10-01 of the Maintenance Manual.
d) Install a new cotter pin (4), P/N Z00.N7323265025.
e) Install tie-wraps securing electrical harness and bonding strap (1).
f) Connect L.H. and R.H. side door links - refer to Chapter 52-80-01 of the
Maintenance Manual.
g) Recondition the aircraft - refer to Paragraph D.
4) In case a crack is suspected :
a) Remove the concerned landing gear leg - refer to Chapter 32-10-01 of the
Maintenance Manual.
b) Confirm the presence of the crack with dye penetrant inspection or fluorescent
penetrant inspection - refer to Chapter 20-50-01 ofthe Maintenance Manual.
JAN 06  Page 4 / 6
Rev. 3 - DEC 14

### Page 5 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-130  REVISION 3  32  ATA No.
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
5) If no crack is found :
a) Protect bare metal with Alodine 1200 and a coat of primer paint.
b) Perform paint touch-up.
NOTE :
As an alternative process to protect bare metal, protective varnish as listed in
"CONSUMABLE MATERIAL" paragraph or any equivalent locally approved
product may be used to facilitate further repetitive dye penetrant inspections or
dye fluorescent inspections.
c) Recondition controlled area in its original condition.
d) Install landing gear leg - refer to Chapter 32-10-01 of the Maintenance Manual.
e) Recondition the aircraft - see Paragraph D.
6) If the crack is confirmed, contact DAHER-SOCATA to coordinate the landing gear
repair and then imperatively conform to any instruction stated by DAHER-SOCATA.
D. RECONDITIONING - see Figure 1
1) Remove the warning sign prohibiting "SOURCE" selector operation.
WARNING
PRIOR TO ANY LANDING GEAR OPERATION, MAKE SURE THE LANDING GEAR
AREA IS CLEAR.
2) Close "LDG GR" landing gear breaker.
3) Perform a complete extension/retraction cycle.
4) Set "SOURCE" selector to "OFF".
5) Lower the aircraft to ground and remove the jacks - refer to Chapter 07-10-00 of the
Maintenance Manual.
6) Make sure all the tools and materials are removed and the work area is clean and free
from debris.
E. TERMINATING SOLUTION
Installation of a L.H. reinforced body D68161 or D68161-1 and of an R.H. reinforced
body D68162 or D68162-1 in compliance with instructions provided in Component
Maintenance Manuals 32-11-01 and 32-11-02.
UPDATING OF THE AIRCRAFT DOCUMENTATION:
Upon completion of Service Bulletin No. SB 70-130-32, Revision 3 "MAIN LANDING GEAR
INSPECTION", make an appropriate maintenance record entry.
WARNING  DAHER-SOCATA considers that it is MANDATORY for operators to comply with the
instructions of this SB.
Operators who arbitrarily ignore the compliance statement indicated in this SB do so at their
own risk.
JAN 06  Page 5 / 6
Rev. 3 - DEC 14

### Page 6 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70 - 130  REVISION 3  ATA No.  32
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
1 - Bonding strap
2 - Attaching lug
3 - Nut
4 - Cotter pin
5 - Bending radius
6 - Area to be inspected
7 - Embossment
Figure 1 - Inspection of main landing gears
JAN 06  Page 6 / 6
Rev. 3 - DEC 14

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
