# Daher Service Bulletin 70-254: No revision named

- Rights: © Socata. Filed by the FAA in regulations.gov docket FAA-2020-1069; AD 2021-25-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Daher Service Bulletin 70-254](https://openairdocs.org/service-documents/daher/sb-70-254.md)
- Title as filed: Daher Aerospace Service Bulletin 70-254
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/71/c2/71c28b09b878938ef8e392889c5e412f731fdb945c3c5332644aca39e1406ede
- Page: https://openairdocs.org/service-documents/daher/sb-70-254/file/71c28b09b878

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Page 1 / 10APR 18
Rev. 3 --- DEC 17
SUBJECT : O I LCOOLER AIR INDUCTION DUCT
REFERENCE : MOD70---0616---79
EFFECTIVITY : TBM S/N 1 to 684 which have applied SB70---231---79, Originalissue.
TBMS/N687to1038whichhaveappliedSB70---219---24,Originalissueand/orRevision1.
TBM S/N 1039 to 1230
NOTE :
For the other aircraft, the modification MOD70- - -0616- - -79 is applied at the factory.
PURPOSE :
A. PROBLEM
Possible increase of oil temperature which may lead to an engine shutdown while
maneuvering margin is reduced due to ice accumulation.
B. ROOT CAUSE
Lossofefficiencyofoilcooler systemcaused byice accumulationon airinlet ductfins.
C. SOLUTION
Removalof the four upper fins of the oilcooler air induction duct.
SUMMARY :
A. PRELIMINARY STEPS
B. OILCOOLER AIR INDUCTIONDUCT MODIFICATION
C. FINALSTEPS
APPLICATION: During the next scheduled inspection and at the latest on October 1st, 2018.
WARRANTY : Parts will be covered under warranty regardless of the warranty status of the aircraft. This
campaign willend 1 year and 1 month after the SB issue reference date.
PROCURABLE MATERIAL:
Parts to be ordered from your TBM spare parts distributor :
--- EpoxyresinandhardenerRef.EPOLAM2017orresinEL---360andhardenerEL---360---1,
or equivalent.
SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
isthe subject ofan AD
SB 70--254
REVISION 3
79
ATA No.
DAHER AEROSPACE
Di
rection des Services TELEPHONE: 33(0)562.41.73.00
65921TARBESCEDEX9 TELEFAX: 33(0)562.41.76.54
FRANCE

### Page 2

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 2 / 10AP R 18
Rev. 3 --- DEC 17
CONSUMABLE MATERIAL or OTHER PRODUCTS(Lo calpurchase) :
--- Methyl---Ethyl---Ketone (M.E.K.)
TOOLS :
--- Standard aeronauticalmaintenance station tools
RELATED DOCUMENTS:
--- Maintenance Manual, Chapters 06---30---01 page 001 and 71---10---00 page 401.
MANPOWER :
--- 1 aeronauticalmechanic :3 hours
TECHNICAL INCIDENCES:
--- None
DESCRIPTION OF ACCOMPLISHMENT INSTRUCTIONS:
NOTE :
Operations required in this Service Bulletin must be accomplished by persons authorized by
their Airworthiness Authorities and according to the procedure described hereafter.
A. PRELIMINARY STEPS
1) Make sure the ”SOURCE” selector is set to ”OFF” and the crash lever is down.
2) Install the warning sign prohibiting ”SOURCE” selector operation
WARNING
DO NOT OPERATE
MA
INTENANCE WORK IN PROGRESS
3) Remove front lower cowling 122 --- refer to Chapters 06---30---01 page 001 and
71
---10---00 page 401 of the MaintenanceManual.
4) Remove rear L.H. cowling 133 --- refer to Chapters 06---30---01 page 001 and
71---10---00 page 401 of the MaintenanceManual.
5) Remove and retain clamps (3) and (5);disconnect hoses (2) and (4).
6) Remove and retain bolts (7) and washers (6).
7) Remove and retain bolts (9) and washers (8).
8) Hold oilcooler (11), then remove and retain oilcooler air induction duct (1).
9) Temporarily install oil cooler (11) on bracket (12) and strut (13) with bolts (7) and
washers (6).

### Page 3

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 3 / 10AP R 18
Rev. 3 --- DEC 17
B. OILCOOLER AIR INDUCTIONDUCT MODIFICATION --- see Figure 1
WARNING
WEAR MASK, PROTECTION GLOVES AND GOGGLES.
NOTE :
To guide you through this process, some photographies are available at the end of
this Service Bulletin.
1) Usingcuttingpliers,cutanddiscardthefourupperfinsoftheoilcoolerairinduction
duct (1) --- see Figure 1 .
2) With a belt sander, fully remove the four upper fins and sand the surfaces that will
be protected by resin at step 5).
3) Vacuum chips and clean area with a clean cloth moistened with M.E.K.
4) Degrease untilremovalof anytrace of dirt or grease from both surfaces.
Oil cooler air induction duct Ref. T700H792001900400, T700H792001900600,
T700H792000900000 orT700A7920040001
CAUTION
REFER TO RESIN AND HADENER NOTICE FOR PREPARATION AND USE.
5) Protect bare surface with epoxy resin and hardener Ref. EPOLAM 2017 or resin
EL---360 and hardener EL---360---1 or equivalent.
All
6) Aftermodificationoftheoilcoolerairinductionduct(1),itmustbere---identifiedwith
a permanent marker, as indicated hereafter :
Pre---SB Reference Post---SB Reference
T700H792001900600 T700H512008100000
T700H792001900400 T700H512008100100
T700A7920040001 T700H512008100200
T700H792001900200 T700H512008100300
T700H792001900000 T700H512008100400
T700H792000900000 T700H512008100500
C. FINALSTEPS
1) Remove oil cooler (11) from bracket (12) and strut (13) temporarily installed at
step A.9).
2) Installoilcooler modified air induction duct (1) on oilcooler (11).
3) Installwashers (6) and bolts (7). Screw but do not fully tighten.
4) Installwashers (8) and bolts (9). Screw but do not fully tighten.
5) Connect hoses (2) and (4) on oil cooler modified air induction duct (1) with
clamps (3) and (5).

### Page 4

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 4 / 10AP R 18
Rev. 3 --- DEC 17
6) Tightentheassembly.Makesurethatoilcoolerairinducti on duct(1)isnotstressed.
7) Make sure all the tools and materials are removed and the work area is clean and free
from debris.
8) Install front lower cowling 122 --- refer to Chapters 06---30---01 page 001 and
71---10---00 page 401 of the MaintenanceManual.
9) InstallrearL.H.cowling133---refertoChapters06---30---01page001and71---10---00
page 401 of the Maintenance Manual.
10) Remove the warning sign prohibiting ”SOURCE” selector operation.
UPDATING OF THE AIRCRAFT DOCUMENTATION:
Upon completion of Service Bulletin No. SB 70---254---79 ”OIL COOLER AIR INDUCTION
DUCT”, (Reference MOD70---0616---79), make an appropriate maintenance record entry.
WARNING : DAHER AEROSPACE considers that it is MANDATORY for operators to comply with the
instructions of this SB.
OperatorswhoarbitrarilyignorethecompliancestatementindicatedinthisSBdosoattheir
own risk.

### Page 5

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 5 / 10AP R 18
Rev. 3 --- DEC 17
Key to Figure 1 --- Oilcooler air induction duct modification
1 --
- Oilcooler air induction duct
2 --- Hose
3 --- Clamp
4 --- Hose
5 --- Clamp
6 --- Washer
7 --- Bolt
8 --- Washer
9 --- Bolt
10 --- Spacer
11 --- Oilcooler
12 --- Bracket
13 --- Strut

### Page 6 (OCR)

TBM AIRCRAFT
SERVICE BULLETIN  SB 70-254  79  ATA No
MANDATORY
The technical content of this document is approved
under the authority of DOA No. EASA.21J.013
is the subject of an AD
PRE SB70-254-79  POST SB70-254-79
I4792000AAAZMA4600  11
Figure 1 - Oil cooler air induction duct modification
APR 18  Page 6 / 10

### Page 7

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 7 / 10AP R 18
Rev. 3 --- DEC 17
TOOLS
CUTTING

### Page 8

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 8 / 10AP R 18
Rev. 3 --- DEC 17
FINISH CUTTING
SAN
DING

### Page 9

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 9 / 10AP R 18
Rev. 3 --- DEC 17
POST---SANDING

### Page 10

SERVICE BULLETIN
TBM AIRCRAFT
MANDATORY
The technicalcontent of this document is approved
un
der the authority of DOA No. EASA.21J.013
is the subject of an AD
SB 70--254
REVISION 3
79
ATA No.
Page 10 / 10AP R 18
Rev. 3 --- DEC 17
PROTECTION

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
