# Dassault Service Bulletin 7X-602: No revision named

- Rights: © Dassault Aviation. Filed by the FAA in regulations.gov docket FAA-2025-1729, the docket of AD 2025-22-05. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Dassault Service Bulletin 7X-602](https://openairdocs.org/service-documents/dassault/7x-602.md)
- Title as filed: SB_7X-602_Initial_06-03-2024reducedsizepdf
- Pages: 44
- PDF: https://openairdocs.org/files/sha256/5f/91/5f91658c0546843a5c4eba3f76a10b16ee0815f8ed7da9db881126d9040af516
- Page: https://openairdocs.org/service-documents/dassault/7x-602/file/5f91658c0546

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

FALCON 7X
No 602
JUNE 03, 2024
 
A
TA 00
GENERAL
ENHANCED AVIONICS SYSTEM
EASY IV - LGIO AIRCRAFT
FALCON SERVICE BULLETIN
Copyright © 2024 by Dassault Aviation
All rights reserved. No part of this work may be reproduced or copied
in any form or by any means without written permission
of Dassault A
viation.
769

### Page 2

GENERAL
ENHANCED A
VIONICS SYSTEM
EASY IV - LGIO AIRCRAFT
Initial issuance March 05, 2024
List of effective pages:
1 to 42
Erratum June 03, 2024
List of effective pages:
1 to 42
REASON: Additional information.
FALCON 7X 7X -602
ATA 00

### Page 3

GENERAL
ENHANCED A
VIONICS SYSTEM
EASY IV - LGIO AIRCRAFT
 
1. PLANNING INFORMATION
A. EFFECTIVITY
This Service Bulletin is applicable to FALCON 7X aircraft with serial numbers 2 thru 261 that have not
previously implemented DASSAULT AVIATION FALCON modification M2059.
B. REASON
The purpose of this Service Bulletin is to upgrade the aircraft avionics to the EASy IV load 18.0
standard that includes the following features:
• an advanced version of the INAV moving map with interactive Vertical Situation Display,
combined with new Vivid Displays,
• a combination of the most advanced versions of Honeywell’s NextGen FMS and Communication
Management Function,
• a dual charts function on aircraft already equipped with single charts, which introduces
redundancy for the use of the electronic Jeppesen charts,
• improved Jeppesen charts function with a new Night mode, a Panoramic mode, as well as the
display of the aircraft symbol on all georeferenced terminal charts (dual charts required),
• Runway Overrun Awarness and Alerting System (ROAAS) which analyzes the aircraft trajectory
and the TOLD landing performance to determine if the aircraft can safely come to a full stop
within the remaining runway length,
• enhanced ADS-B IN Cockpit Display of Traffic Information (CDTI) with 2 applications:
• Visual Separation on Approach (VSA): displays specific traffic information relative to select
traffic, to facilitate visual separation,
• AIRB: displays ADS-B airborne traffic on the INAV moving map,
• enhanced TOLD function,
• "push-to-load" function,
• weak point fix in the Falcon 7X EASy avionics architecture (equivalent to DASSAULT AVIATION
Service Bulletin 7X-591 "EASY II 5TH CERT - LEGACY I/O"). This weak point can lead to the
display of misleading data on the display units.
C. DESCRIPTION
The operation consists in:
• modifying the aircraft wiring,
• installing wiring provision in anticipation of a future radar installation,
• modifying the hardware configuration:
• replacement of modules in MAU 1 and 2,
• replacement of NIM modules,
• replacement of ASCB bus coupler modules,
• replacement of TCAS transceiver and antennas,
• replacement of DMU by DLMU,
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 1 / 42
DASSAULT AVIATION Proprietary Data

### Page 4

• performing a full software load.
D.
COMPLIANCE
If you choose to comply with this Service Bulletin, accomplishment can be performed at your
convenience.
E. APPROVAL
This Service Bulletin covers DASSAULT AVIATION modifications:
• M-OPT22, M-OPT640, M-OPT1142, M-OPT1144, M1254, M1314, M1341 and M2059 that have
been approved by EASA.
• M1363, M2034, M2060, M2104 and M2128 that have been approved under the authority of the
DOA ref. EASA.21J.051.
The technical content of this document is approved under the authority of DOA ref. EASA.21J.051.
NOTE: For aircraft not under EASA and FAA regulations, please refer to the Falcon Service Advisory
that lists the countries for which EASy IV is approved.
F. LABOR
Estimated labor-hours: Refer to Service Bulletin Commercial Summary
.
NOTE: These labor-hours only concern the work described in this Service Bulletin and do not include
other maintenance work that may be performed on this occasion.
G. MATERIAL - PRICE AND AVAILABILITY
The modification kit may be obtained from either address listed below:
Western hemisphere: DASSAULT FALCON JET CORP.
SP
ARES DISTRIBUTION CENTER
200 RISER ROAD
LITTLE FERRY, NJ 07643 U.S.A.
Telephone:
• U.S.A. and CANADA: 1-800-800-4036
• MEXICO: 001-800-800-4036
• Other countries: 1-201-541-4809
Email to: Customer.Care@DassaultFalconJet.com
Other continents: DASSAULT AVIATION
Falcon Spares
54, A
VENUE MARCEL DASSAULT
B.P. 24
33701 MERIGNAC Cedex (FRANCE)
Telephone: 33 (0)5.56.18.44.44
Email to: dafsorders@dassault-aviation.com
Price and availability on request.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 2 / 42
DASSAULT AVIATION Proprietary Data

### Page 5

H. TOOLING - PRICE AND AVAILABILITY
T
OOL BOX (TO-20-008)
I.
WEIGHT AND BALANCE
Change in weight: None.
Change in balance with respect to 25% MAC: None.
J. REFERENCES
Structural Repair Manual:
• DRILLING (Refer to RPI 51-40-03)
•
RIVETING (Refer to RPI 51-40-04)
•
COUNTERSINKING (Refer to RPI 51-40-06)
Aircraft Maintenance Manual:
•
GENERAL MAINTENANCE AND SAFETY PRECAUTIONS (Refer to TASK 20-00-00-910-801)
•
USE OF THE AIRCRAFT MAINTENANCE PROCEDURES (Refer to TASK 20-00-00-910-803)
•
BASIC SEALING METHODS (Refer to TASK 20-32-00-390-801)
•
REPLACEMENT OF LOCKWIRES AND SNAPWIRES (Refer to TASK 20-42-01-960-801)
•
PROTECTION SCHEME (Refer to SDS 20-60-00)
•
APPLICATION OF ALODINE (Refer to TASK 20-60-00-370-801)
• APPLICA
TION OF TYPE 5014 AND 5015 POLYURETHANE PRIMERS (Refer to TASK
20-60-00-370-809)
•
UNPLUGGING / PLUGGING OF THE MAU BACKSHELLS (Refer to TASK 20-92-00-910-801)
• INSER
TION AND EXTRACTION OF A WIRE FITTED WITH A LOCK-IN CONTACT (Refer to
TASK 20-95-00-910-801)
• ENERGIZA
TION / DE-ENERGIZATION OF THE AIRCRAFT SYSTEMS (Refer to TASK
24-00-00-860-801)
• REMOV
AL / INSTALLATION OF THE ELT CONTROL PANEL (Refer to TASK
25-61-17-900-801)
•
REMOVAL / INSTALLATION OF THE MAU CHASSIS (Refer to TASK 31-41-01-900-801)
• REMOV
AL / INSTALLATION OF THE POWER SUPPLY MODULES (Refer to TASK
31-41-05-900-801)
• REMOV
AL / INSTALLATION OF THE PROCESSOR MODULES (Refer to TASK
31-41-09-900-802)
• OPERA
TIONAL TEST OF THE DATA ACQUISITION SYSTEM - MAU (Refer to TASK
31-42-00-710-801)
• REMOV
AL / INSTALLATION OF THE NIC / PROCESSOR MODULES (Refer to TASK
31-42-01-900-801)
• REMOV
AL / INSTALLATION OF THE CONTROL I/O 2 MODULE (Refer to TASK
31-42-05-900-801)
• REMOV
AL / INSTALLATION OF THE CONTROL/VIDEO I/O 1 MODULE (Refer to TASK
31-42-09-900-801)
• REMOV
AL / INSTALLATION OF THE GENERIC I/O MODULES (Refer to TASK
31-42-13-900-801)
• REMOV
AL / INSTALLATION OF THE ASCB BUS COUPLERS (Refer to TASK
31-42-17-900-801)
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 3 / 42
DASSAULT AVIATION Proprietary Data

### Page 6

• REMOV AL / INSTALLATION OF THE NETWORK INTERFACE MODULES (NIM) (Refer to
TASK 31-43-05-900-801)
• OPERA
TIONAL TEST OF THE CENTRAL DISPLAY SYSTEM (CDS) (Refer to TASK
31-60-00-710-801)
• REMOV
AL / INSTALLATION OF THE ADVANCED GRAPHICS MODULES (AGM) (Refer to
TASK 31-60-17-900-801)
• REMOV
AL / INSTALLATION OF THE AIR DATA, ATTITUDE AND HEADING REFERENCE
SYSTEM (ADAHRS) UNIT (Refer to TASK 34-22-01-900-801)
• OPERA
TIONAL TEST OF THE TRAFFIC / COLLISION AVOIDANCE SYSTEM (TCAS) (Refer to
TASK 34-44-00-710-801)
•
REMOVAL / INSTALLATION OF THE TCAS TRANSCEIVER (Refer to TASK 34-44-01-900-801)
•
REMOVAL / INSTALLATION OF THE TCAS ANTENNAS (Refer to TASK 34-44-05-900-801)
• OPERA
TIONAL TEST OF THE ENHANCED GROUND PROXIMITY WARNING SYSTEM
(EGPWS) (Refer to TASK 34-45-00-710-801)
• OPERA
TIONAL TEST OF THE CENTRAL MAINTENANCE COMPUTER (CMC) (Refer to TASK
45-10-00-710-801)
•
INSTALLATION OF AVIONICS SOFTWARE TOOLS (Refer to TASK 45-10-00-860-801)
• REMOV
AL / INSTALLATION OF THE FLIGHT DECK PRINTER (Refer to TASK
45-10-09-900-801)
•
PERIODIC DATABASE LOADING (Refer to TASK 45-90-00-860-801)
•
DATABASE LOADING (Refer to TASK 45-90-00-860-803)
•
SOFTWARE LOADING (Refer to TASK 45-90-00-860-804)
• REMOV
AL / INSTALLATION OF THE DATA MANAGEMENT UNIT (DMU) (Refer to TASK
45-90-01-900-801)
• REMOV
AL / INSTALLATION OF THE DATA LAN MANAGEMENT UNIT (DLMU) (Refer to TASK
45-90-01-900-802)
•
USE OF THE APM SETTINGS TOOL (Refer to TASK 45-91-00-910-801)
• REMOV
AL / INSTALLATION OF THE CABIN FLOOR PANELS (Refer to TASK
53-04-01-900-801)
• REMOV
AL / INSTALLATION OF THE OPTIONAL EQUIPMENT FLOOR PANEL (Refer to TASK
53-04-07-900-801)
•
OPENING / CLOSING OF THE NOSE CONE (Refer to TASK 53-10-09-860-801)
•
REMOVAL / INSTALLATION OF THE T34 BODY FAIRINGS (Refer to TASK 53-60-00-900-801)
Wiring Diagram Manual:
•
Refer to WD 23-10-00
•
Refer to WD 23-10-20
•
Refer to WD 34-23-50
•
Refer to WD 34-40-00
•
Refer to WD 34-45-00
•
Refer to WD 45-90-00
DASSAUL
T AVIATION Service Bulletins/Modifications:
• M111 "BIRD STRIKE INTO FRAME 1"
• 7X-603 "LOADING THE LATEST AMI DATABASE AND SWITCHING AMI DATABASE
PROVIDER" 
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 4 / 42
DASSAULT AVIATION Proprietary Data

### Page 7

K. OTHER PUBLICATIONS AFFECTED
The following publication is revised to account for the changes introduced by this Service Bulletin:
•
Airplane Flight Manual revision 25 or subsequent revision
The following publications will be revised at a later date to account for the changes introduced by this
Service Bulletin:
• CODDE 1 revision 14
• CODDE 2 revision 25
• QRH 1 revision 25
• QRH 2 revision 25
• Illustrated Parts Catalog
• Aircraft Maintenance Manual
• Fault Isolation Manual
• Wiring Diagram Manual
Operational Suitability Data:
• Operational Suitability Data - Flight Crew:
• OSM-FC revision 8 or subsequent revision
• Operational Suitability Manual - Master Minimum Equipment List:
• OSM-MMEL revision 16 or subsequent revision
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 5 / 42
DASSAULT AVIATION Proprietary Data

### Page 8

2. ACCOMPLISHMENT INSTRUCTIONS
Refer to fig. 1 for general view of the work area.
A.
GENERAL INSTRUCTIONS AND SAFETY PRECAUTIONS
(1) Obey the general maintenance and safety precautions (Refer to TASK 20-00-00-910-801).
(2)
Obey the general electrical instructions:
(a) When mechanical retrofit and/or modification operations are performed on the aircraft, take
special care to protect the wiring in order to prevent metal chips (or burrs) from penetrating
the wire bundles, since these could eventually damage the insulation sheathing of the wires.
Whenever possible, it is recommended that the wiring be removed from the work area. If
that is not possible, it is absolutely necessary to protect the wiring.
(b) Due to the risk of damaging the wire insulation, it is prohibited to blindly drill holes through a
box structure containing wiring.
(c) New wires that are installed alongside existing wires should be secured with the existing
clamp.
(d) Check that all connections are properly protected to ensure proper insulation, and that
markings are visible and appropriate.
(e) Connector wires should be inserted and extracted as per the recommendations in Standard
Practices (Refer to TASK 20-95-00-910-801).
(f) Electrical 
and electronic equipment should be removed and installed as per the
recommendations in Standard Practices (Refer to TASK 20-00-00-910-801).
(g) V
isually inspect the work area for particles or debris, then vacuum-clean the area. Blowing
compressed air is prohibited since it could move metal chips into inaccessible areas.
(3) Obey the Structural Repair Manual and Standard Practices procedures for the following
operations:
• drilling (Refer to RPI 51-40-03),
•
riveting (Refer to RPI 51-40-04),
•
countersinking (Refer to RPI 51-40-06),
•
basic sealing methods (Refer to TASK 20-32-00-390-801).
B.
PRELIMINARY STEPS
(1) The aircraft must be in the maintenance configuration (Refer to TASK 20-00-00-910-803).
(2) On 
the “System Config” page, note the APM Settings configuration on the table (Refer to TASK
45-91-00-910-801).
(3)
De-energize the aircraft systems (Refer to TASK 24-00-00-860-801).
(4)
Open the nose cone (210) (Refer to TASK 53-10-09-860-801).
(5) Remove 
the necessary equipment and interior accommodation items to get access to cockpit and
cabin floors (113JZ), (114AZ), (114BZ), (114CZ), (114DZ), (114FZ), (114GZ), (121BZ), (121CZ),
(121DZ), ( 121EZ), ( 121FZ), ( 121GZ), (122AZ), (122BZ), ( 122CZ), ( 131BZ) and (131CZ).
(6)
Remove the cabin floors listed above (Refer to TASK 53-04-01-900-801).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 6 / 42
DASSAULT AVIATION Proprietary Data

### Page 9

(7) Remove the optional equipment floor panel (Refer to TASK 53-04-07-900-801).
(8)
Remove the ADAHRS UNIT (Refer to TASK 34-22-01-900-801).
(9)
Remove the TCAS transceiver (103NP) (Refer to TASK 34-44-01-900-801).
(10)
Remove the DMU (901FP) (Refer to TASK 45-90-01-900-801).
(1
1) Remove the ELT control panel (701FP) (Refer to TASK 25-61-17-900-801).
(12)
If installed, remove the printer (104MP) (Refer to TASK 45-10-09-900-801).
(13)
Remove the MAU 1 chassis (Refer to TASK 31-41-01-900-801).
(14)
Remove the following backshells from the MAU 2 (Refer to TASK 20-92-00-910-801):
•
AGM modules (2301FD) and (2401FD)
•
NIC/processor modules (2301FY) and (2401FY)
•
CMC module (2505TC)
(15) Remove 
the backshells from the NIM modules ( 1101NZ) and ( 1201NZ) (Refer to TASK
31-43-05-900-801).
C.
STRUCTURAL MODIFICATIONS
(1) Prepare FR1 RH side for the installation of the new cut-off connector 87J/P as follows:
(a) A/C without M111 (SN<102): remove the front plate (a-fig. 10) from FR1.
(b) Create a cut-out on FR1 as per fig. 10.
NOTE: Depending on aircraft configuration, you can create the cut-out either according to
solution 1 or solution 2. Solution 1 is preferable.
(c) Protect the cut-out area (Refer to SDS 20-60-00).
(2) Prepare 
the FR8/FR9 under floor area for the installation of new cut-off connectors 195J/P and
196J/P as follows:
(a) Remove the old supports (a-fig. 11) and (a-fig. 12).
(b) Plug the four old rivet positions (b-fig. 11) with new rivets (3-fig. 11).
(c) Install the connector bracket (1-fig. 11) on the omega (2-fig. 11) using rivets (4-fig. 11).
(d) Install the assembly (1-fig. 11) and (2-fig. 11) on the frame using rivets (5-fig. 11).
(e) Install the new bundle bracket (1-fig. 12 ) on RH lower FR8/FR9 web (b-fig. 12) in place of
the old bracket (a-fig. 12) using rivets (2-fig. 12).
(f) Install the cable holder (4-fig. 12) on the bundle bracket (3-fig. 12) using rivet (5-fig. 12).
(g) Install the assembly (3-fig. 12) and (4-fig. 12) on the structure (c-fig. 12) using rivets (6-fig.
12).
(h) Install the cable holder (1-fig. 13) using rivet (2-fig. 13).
(3) Prepare the RH copilot sideledge area for the installation of the LAN terminal load R5821FY as
follows:
(a) Position the LAN terminal load bracket (1-fig. 14) in accordance with the dimensions shown
on figure fig. 14.
(b) Drill two holes for rivets (2-fig. 14), then install the bracket.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 7 / 42
DASSAULT AVIATION Proprietary Data

### Page 10

D. ELECTRICAL MODIFICATIONS
(1)
Perform the following modification on each AGM backshell 1:
(a) Fill the new connector (2-fig. 2) with blanking pins.
NOTE: This new connector has no wire connected to it.
(b) Open backshell 1.
(c)
Remove the blank backplate (a-fig. 2).
(d) Install the connector backplate (1-fig. 2 ) and the connector (2-fig. 2).
(e) Close backshell 1.
(2) Perform the following modification on each AGM backshell 2:
(a) Open backshell 2.
(b) Disconnect the two wires of the terrain server bus from the backshell (item 1-fig. 3).
(c) Cap and stow the two wires inside the backshell.
(d) Close backshell 2.
(3) Perform the following modification on the backshell of the EGPWS 1 module ( 101FW):
(a)
Open the backshell.
(b) Disconnect the two wires of the terrain server bus from the backshell (item 2-fig. 3).
(c) Cap and stow the two wires with the wiring bundle under the cabin floor.
(d) Discard the backshell.
(4) Perform the electrical modification of the LAN bus as per wiring diagrams fig. 3 and fig. 14.
NOTE 1: Disconnected LAN bus cables must be capped and stowed outside the backshells 
(item 3-fig. 3).
NOTE 2: New triaxial cables must have a minimum length of 500 mm.
NOTE 3: New triaxial cables must be secured with spacers (3-fig. 14) and (4-fig. 14).
(5) Perform the electrical modification as per wiring diagrams fig. 4 and fig. 15.
NOTE 1: This wiring diagram includes wiring provision in anticipation of a future radar
installation.
NOTE 2: Quadrax cable technology does not allow elements to be crossed. Before the
installation 
of quadrax contacts, identify the ends of the cables after cut, and route the
cable according to the direction of rotation of the colors, in order not to cross the
elements in the rear insulator of the quadrax contacts.
(a) If necessary, remove the duct F7XC213220100A1 to easily route the harness.
(b) Connector 
1101NZ1: if there is no space available for the new quadrax cable in the
hexashield store, do the following steps:
1 Remove the two hexashields P/N 01C0AFHE3-7 (hexashields without bonding braid).
2 Install all the cables previously associated to these two hexashields in a same
hexashield P/N 01C0AFHE3-7 (local procurement).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 8 / 42
DASSAULT AVIATION Proprietary Data

### Page 11

3 Install the new quadrax cable in the space now available in the hexashield store.
(6)
Perform the following modification on the DLMU connectors:
(a) Replace the Hexashield hood of the aircraft electrical connector 1001FP1 with the new
reference (02C0A501CAP3-658).
(b) Secure the protective cap 01C0A501BE6-8D002 by attaching the rope with a cable grip to
the backshell of the electrical connector 1001FP2.
(7) Perform the electrical modification as per wiring diagrams fig. 5 and fig. 6.
(8) Perform an electrical continuity check of the aircraft wiring.
E. HARDWARE / EQUIPMENT MODIFICATIONS
(1) A/C without M111 (SN<102):
(a) Modify the front plate (a-fig. 10) to fit with the new cut-off connector 87J/P.
(b) Protect the modified area (Refer to SDS 20-60-00).
(c)
Reinstall the modifed plate on FR1.
(d) Apply covering sealant on the heads of the screws (Refer to TASK 20-32-00-390-801).
(2)
Install the new TCAS transceiver (103NP) (Refer to TASK 34-44-01-900-801).
(3)
Install the DLMU (1001FP) with its SD card (Refer to TASK 45-90-01-900-802).
(4)
Re-install the MAU 1 chassis (Refer to TASK 31-41-01-900-801), and do the following steps:
(a) Install 
the processor P/N 7034056-1901 in slot 14 (initially in slot 16) (1-fig. 7) (Refer to
TASK 31-41-09-900-802).
(b) Install 
the new processor P/N 7034056-1902 in slot 16 (2-fig. 7) (Refer to TASK
31-41-09-900-802).
(c) Install 
the new NIC/processor modules ( 2101FY) and ( 2201FY) (3-fig. 7) (Refer to TASK
31-42-01-900-801).
(d) Install 
the new AGM modules ( 2101FD) and ( 2201FD) (4-fig. 7) (Refer to TASK
31-60-17-900-801).
(e) Install 
the new processor 10 module ( 2051FY) P/N 7034056-1903 in slot 13 (in place of the
EGPWS 1 module) (5-fig. 7) (Refer to TASK 31-41-09-900-802).
(f) Install 
the new power supply modules ( 1101FY) and ( 1201FY) (6-fig. 7) (Refer to TASK
31-41-05-900-801).
(g) Install 
the new generic I/O modules ( 4101FY), (4201FY) and ( 4501FY) (7-fig. 7) (Refer to
TASK 31-42-13-900-801).
NOTE: P/N for generic I/O 5 module is different from other generic I/O modules (see table
in 3.A. for detail).
(h) Install the new control/video I/O 1 module ( 3101FY) (8-fig. 7) (Refer to TASK
31-42-09-900-801).
(i)
Re-install the other MAU 1 modules (Refer to TASK 31-41-01-900-801).
(j) Remove 
and replace the MAU 1 ASCB bus coupler module ( 5101FY) (Refer to TASK
31-42-17-900-801).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 9 / 42
DASSAULT AVIATION Proprietary Data

### Page 12

(5) Do the following steps on MAU 2:
(a) Remove 
and replace the NIC/processor modules (2301FY) and ( 2401FY) (3-fig. 7 ) (Refer to
TASK 31-42-01-900-801).
(b) Remove 
and replace the AGM modules ( 2301FD) and ( 2401FD) (4-fig. 7) (Refer to TASK
31-60-17-900-801).
(c) Remove 
and replace the power supply modules ( 1301FY) and ( 1401FY) (6-fig. 7) (Refer to
TASK 31-41-05-900-801).
(d) Remove 
and replace the generic I/O modules ( 4301FY) and ( 4401FY) (7-fig. 7) (Refer to
TASK 31-42-13-900-801).
(e) Remove 
and replace the control I/O 2 module ( 3201FY) (9-fig. 7) (Refer to TASK
31-42-05-900-801).
(f) Remove 
and replace the MAU 2 ASCB bus coupler module ( 5201FY) (Refer to TASK
31-42-17-900-801).
(6) Remove 
and replace the NIM modules ( 1101NZ) and ( 1201NZ) (Refer to TASK
31-43-05-900-801).
(7)
Replace the lower TCAS antenna as follows:
(a) Remove the fuel equipment bay door ( 151AL) (Refer to TASK 53-60-00-900-801).
(b)
Remove the lower TCAS antenna (303NP) from the fuel equipment bay door (Refer to TASK
34-44-05-900-801).
(c) Apply 
aircraft paint finish on the new fuel equipment bay door ( 151AL) (item 1) in
accordance with the Protection Scheme (Refer to SDS 20-60-00).
(d) Using 
new screws (item 2) and washers (item 3), install the new lower TCAS antenna
(503NP) (item 4) on the new fuel equipment bay door (Refer to TASK 34-44-05-900-801).
(e)
Install the new fuel equipment bay door (151AL) (Refer to TASK 53-60-00-900-801).
(8)
External access only: replace the upper TCAS antenna following fig. 8:
(a) Remove the upper TCAS antenna ( 203NP) from the fuselage (Refer to TASK
34-44-05-900-801) and retrieve the eight screws and washers.
(b)
Remove the microballon taper shim specific to the old antenna.
(c) Prepare the work area:
• use a Plexiglas spatula to remove sealant to obtain a clean surface,
• clean the work area with lint-free cloth moistened with cleaner.
(d) Protect 
both exposed lateral flange outer shims (a-fig. 8 ) with alodine (Refer to TASK
20-60-00-370-801) and anti-corrosion primer (Refer to SDS 20-60-00).
(e) With 
the help of a template (local procurement), create a microballon taper shim using
compound EC 3524 (b-fig. 8).
(f)
Apply 5 mm interlaying sealant on the existing outer shim (c-fig. 8) all along the internal (d-
fig. 8) and external (e-fig. 8) borders (Refer to TASK 20-32-00-390-801).
(g) Apply 
an interlay of interlaying sealant between the new shim and the fuselage (f-fig. 8 )
(Refer to TASK 20-32-00-390-801).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 10 / 42
DASSAULT AVIATION Proprietary Data

### Page 13

(h) Install the new interface shim (1-fig. 8) above the existing outer shim.
NOTE: This shim will be fastened with the eight antenna screws.
(i) Make sure that the O-ring provided with the new antenna is not installed.
(j) Make 
sure that the wiring insulating sleeves and the connectors, on aircraft side and TCAS
antenna side, are in good condition:
• no unwanted material in the connectors,
• no cracks on the wiring insulating sleeves,
• no pins bent,
• no corrosion on the electrical connectors.
(k) Apply demolding agent  around the antenna periphery exterior side (Refer to TASK
20-32-00-390-801).
(l) Remove 
the protective film marked "ANTENNA SIDE" from the polyurethane gasket (2-fig.
8).
NOTE: The protective film marked "AIRCRAFT SIDE" must stay in place on the
polyurethane gasket.
(m) Position the polyurethane gasket on the antenna.
(n)
Remove the protective film marked "AIRCRAFT SIDE" from the polyurethane gasket.
(o) Position the upper TCAS antenna ( 603NP) (3-fig. 8), with the arrow on the antenna pointing
in the aircraft forward direction.
(p) Connect the four coaxial cables to the relevant connectors on the upper TCAS antenna.
NOTE: Each coaxial cable and its corresponding connector are identified by a specific
color
.
(q) Safety the coaxial cables with the lockwire (Refer to TASK 20-42-01-960-801).
(r)
Install the upper TCAS antenna.
(s) Install the retrieved screws and washers.
CAUTION: DO NOT OVERTORQUE THE SCREWS AS THIS CAN CAUSE CRACKS IN THE
ANTENNA.
(t) Tighten the screws to a torque of 2.2 to 2.8 N.m (19 to 25 lbf.in).
(u)
Apply bead sealant (g-fig. 8) around the antenna base (Refer to TASK 20-32-00-390-801).
(v)
Insert AIREX foam (h-fig. 8), cut to the shape of the screw holes, in the screw holes.
(w) Apply covering sealant (i-fig. 8) on the heads of the screws (Refer to TASK
20-32-00-390-801).
(x) Apply white primer 5014 (j-fig. 8) on the compound EC 3524  (b-fig. 8) (Refer to TASK
20-60-00-370-809).
(y) Apply 
aircraft paint finish up to the paint limit in accordance with the Protection Scheme
(Refer to SDS 20-60-00).
(9)
Internal and external access: replace the upper TCAS antenna following fig. 9:
(a) Remove the upper TCAS antenna ( 203NP) from the fuselage (Refer to TASK
34-44-05-900-801) and discard the screws.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 11 / 42
DASSAULT AVIATION Proprietary Data

### Page 14

(b) Remove the microballon taper shim specific to the old antenna.
(c) Counterdrill 
the rivets (a-fig. 9), (b-fig. 9 ), (c-fig. 9 ) and (d-fig. 9 ) to remove the existing
outer shim and the nut plates.
(d) Prepare the work area:
• use a Plexiglas spatula to remove sealant to obtain a clean surface,
• clean the work area with lint-free cloth moistened with cleaner
(e)
Plug the six old rivet positions (b-fig. 9) with new rivets (2-fig. 9).
(f) Install the 14 rivets (1-fig. 9) to hold the skin on the stringer.
(g) Pin and hold in position the new interface shim (6-fig. 9 ) on the fuselage.
(h) From inside, transfer the holes (3-fig. 9 ) and (4-fig. 9) from the fuselage to the shim to install
new rivets.
NOTE: Depending on aircraft configuration, two of the holes (4-fig. 9) may be missing. In
this case, use the dimensions shown on the fig. 9 to locate the holes to be drilled.
(i) From outside, transfer the three holes (5-fig. 9) from the new shim (6-fig. 9 ) to the fuselage.
(j)
Counterdrill the three holes for the rivets (5-fig. 9).
(k) Remove the shim.
(l) Countersink all holes on the shim.
(m) Apply a 5 mm thick layer of interlaying sealant on the shim all along internal (e-fig. 9) and
external (f-fig. 9) borders (Refer to TASK 20-32-00-390-801).
(n)
Install the shim using rivets (4-fig. 9) and (5-fig. 9).
(o) Apply an interlay of interlaying sealant between the nut plates and the fuselage (g-fig. 9 )
(Refer to TASK 20-32-00-390-801).
(p)
Re-install the nut plates using rivets (3-fig. 9).
(q) With the help of a template (local procurement), create a microballon taper shim using
compound EC 3524 (h-fig. 9).
(r)
Make sure that the O-ring provided with the new antenna is not installed.
(s) Make sure that the wiring insulating sleeves and the connectors, on aircraft side and TCAS
antenna side, are in good condition:
• no unwanted material in the connectors,
• no cracks on the wiring insulating sleeves,
• no pins bent,
• no corrosion on the electrical connectors.
(t) Apply demolding agent  around the antenna periphery exterior side (Refer to TASK
20-32-00-390-801).
(u) Remove 
the protective film marked "ANTENNA SIDE" from the polyurethane gasket (7-fig.
9).
NOTE: The protective film marked "AIRCRAFT SIDE" must stay in place on the
polyurethane gasket.
(v) Position the polyurethane gasket (7-fig. 9) on the antenna.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 12 / 42
DASSAULT AVIATION Proprietary Data

### Page 15

(w) Remove the protective film marked "AIRCRAFT SIDE" from the polyurethane gasket.
(x) Position 
the upper TCAS antenna ( 603NP) (8-fig. 9), with the arrow on the antenna pointing
in the aircraft forward direction.
(y) Connect the four coaxial cables to the relevant connectors on the upper TCAS antenna.
NOTE: Each coaxial cable and its corresponding connector are identified by a specific
color
.
(z) Safety the coaxial cables with the lockwire (Refer to TASK 20-42-01-960-801).
(aa)
Install the new screws (9-fig. 9) and washers (10-fig. 9).
CAUTION: DO NOT OVERTORQUE THE SCREWS AS THIS CAN CAUSE CRACKS IN THE
ANTENNA.
(ab) Tighten the screws to a torque of 2.2 to 2.8 N.m (19 to 25 lbf.in).
(ac)
Apply bead sealant (i-fig. 9) around the antenna base (Refer to TASK 20-32-00-390-801).
(ad)
Insert AIREX foam (j-fig. 9), cut to the shape of the screw holes, in the screw holes.
(ae) Apply covering sealant (k-fig. 9) on the heads of the screws (Refer to TASK
20-32-00-390-801).
(af)
Apply white primer 5014 (l-fig. 9) on the compound EC 3524 (h-fig. 9).
(ag) Apply aircraft paint finish up to the paint limit in accordance with the Protection Scheme
(Refer to SDS 20-60-00).
(10)
Re-install all the other equipment removed when performing this Service Bulletin.
F. SOFTWARE LOADING
CAUTION: PRIOR TO STARTING THE SOFTWARE LOADING, MAKE SURE THAT YOU HAVE ALL
THE REQUIRED SOFTW
ARE/DATABASES MENTIONED IN PARAGRAPH 3.
(1) Energize the aircraft systems (Refer to TASK 24-00-00-860-801  - "Connection of the electrical
ground power unit" and “Energization with the electrical ground power unit”).
NOTE: You don't need to record the current APM settings configuration because this procedure
has already been done at step 
2.B.(2).
(2) Uninstall the old version of the Remote Terminal software from the client laptop.
CAUTION: USING AN INAPPROPRIATE VERSION OF CMC-RT / DLS TO LOAD THE
SOFTW
ARE OR DATABASE CAN LEAD TO AGM FAILURES WHICH MAY
REQUIRE AGM REPLACEMENT.
(3) Install the new version of the Remote Terminal software included in the HONEYWELL EPIC Tools
CD-ROM (Refer to TASK 45-10-00-860-801).
(4) Load 
the new software and databases in accordance with the data loading procedures (Refer to
TASK 45-90-00-860-801 ), (Refer to TASK 45-90-00-860-803 ), (Refer to TASK
45-90-00-860-804) and following the sequence hereafter:
CAUTION: PRIOR TO STARTING THE OPERATIONAL SOFTWARE LOADING, MAKE SURE
THA
T THE “CRC32” VALUE CONTAINED ON THE LOAD CD-ROM MATCHES THE
CRC VALUE SHOWN ON FALCON PORTAL (REFER TO TASK 45-90-00-860-804).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 13 / 42
DASSAULT AVIATION Proprietary Data

### Page 16

NOTE: The "System Config ID" pages where you can check APM Data and Database Config ID
can 
only be accessed after all the FMS databases (FMS AEDB / Magvar / TOLD
Database / INDS EPIC AIRSPACE & COMM NAVIGATION DATA) have been loaded.
SOFTWARE KEY WORD EFFECTIVITY
Operational Software Top Level
System Part Number
EB60007394-01
16
Load 18.0
All aircraft
Creation of the APM Settings files:
• Create 
and save the APM Settings file on the hard drive using the APM
Settings Tool included in the HONEYWELL EPIC Tools CD-ROM and
the configuration noted previously. Use the settings.def definition file
from the load 18.0 Operational Software located in the apm_defn folder.
NOTE: The create and load feature should not be used.
• Load the settings file created from the hard drive using DLS.
• Make 
a copy of this file generated by the APM Settings Tool on a media
(e.g. CD-ROM) and keep a copy on-board the aircraft.
NOTE: It is recommended to print the "settings.text" file generated by
the 
APM Settings Tool to keep a record of the latest settings
configuration.
TT60005561-XXXXX*
APM Options parameter configuration
NOTE: If an authorization code is
required, 
it will be specified on
the CD-ROM label (Refer to
TASK 45-90-00-860-803).
18.0.1* LDI
Refer to 7X-603 Airline Modifiable Information (AMI)database Aircraft with Datalink installed
V0015* FLT (Fault Code database)
All aircraft
V0016* OPS (Consequences database)
V0038* ECL
Latest applicable version ECB
PS60002392-0007* FMS AEDB
PS60001004-0004* FMS MAGVAR
PS60004646-003* FMS TOLD
DS7-YYCC-RRR*
or
DS8-YYCC-RRR* (1)
INDS EPIC AIRSPACE
& COMM NA
VIGATION DATA
(1) for operator with RNP AR OPS
APPROV
AL (RNP AR=0.3 or RNP AR
DOWN TO RNP 0.1 APPROACH)
Full charts INDS Electronic Terminal Charts
All aircraftDO69002412-0XXX*
(EGPWF database)
INDS EGPWF Data
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 14 / 42
DASSAULT AVIATION Proprietary Data

### Page 17

SOFTWARE KEY WORD EFFECTIVITY
996-0114-5XX*
(envelope modulation)
996-0146-6XX* INDS Terrain server
PS60001005-0015* ATC Database Aircraft with SB 7X-308
P1182 Issue 1* ACMF Optional but recommended to allaircraft for troubleshooting
69003872-040* EGPWF ROAAS Database All aircraft
* or latest applicable version (the most current software and database versions which can be loaded on the aircraft are
now 
tracked in the "MAINTENANCE DOCUMENTATION - Documentation Status" section of the Falcon Portal, where
you will be given the most up-to-date versions depending on the aircraft configuration).
(5) Discard all of the previous versions of the software, Options, Settings, Operator Tools and
Database CD-ROMs.
(6) Due to the Operational Software to EB60007394-0116, contact INDS to request the Navigation
database changes from (refer to Service Bulletin Commercial Summary):
• DS3 to DS7, or
• DS4 to DS8 for operator with RNP AR OPS APPROVAL.
G. TESTS
(1) Perform the operational test of the TCAS system (Refer to TASK 34-44-00-710-801).
(2)
Perform the test after installation of the DLMU (Refer to TASK 45-90-01-900-802).
(3)
Perform the test after installation relative to the following MAU modules:
• AGM modules (Refer to TASK 31-60-17-900-801)
• Processor
, NIC/processor, power supply and ASCB bus coupler modules (Refer to TASK
31-42-00-710-801)
•
Generic IO modules (Refer to TASK 31-42-13-900-801)
•
Control/video I/O 1 module (Refer to TASK 31-42-09-900-801)
•
Control I/O 2 module (Refer to TASK 31-42-05-900-801)
•
CMC module (Refer to TASK 45-10-00-710-801)
(4)
Perform the test after installation of the NIM modules (Refer to TASK 31-43-05-900-801).
(5)
Perform the operational test of the EGPWS (Refer to TASK 34-45-00-710-801).
(6) Perform 
the operational test of the Central Display System (CDS) (Refer to TASK
31-60-00-710-801).
(7) Perform 
the test of all the other equipment removed when performing this Service Bulletin, in
accordance with the Maintenance Manual Procedures.
H. FINAL STEPS
(1) De-energize the aircraft systems (Refer to TASK 24-00-00-860-801  - “De-energization with the
electrical ground power unit” and "Disconnection of the electrical ground power unit").
(2) Install the floors listed in step 2.B.(6) (Refer to TASK 53-04-01-900-801).
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 15 / 42
DASSAULT AVIATION Proprietary Data

### Page 18

(3) Install all the interior accommodation removed for access.
(4)
Close the nose cone (210) (Refer to TASK 53-10-09-860-801).
I.
DOCUMENTATION
Incorporate Airplane Flight Manual revision 25 or subsequent revision pages.
Incorporate fig. 3 in Wiring Diagram Manual chapter 34-23-50.
Incorporate fig. 4 in Wiring Diagram Manual chapters 23-10-00, 23-10-20 and 45-90-00.
Incorporate fig. 5 and fig. 6 in Wiring Diagram Manual chapters 34-40-00 and 34-45-00.
J. RECORDING
Record compliance with DASSAULT AVIATION Service Bulletin 7X-591 "EASY II 5TH CERT -
LEGACY I/O".
Record compliance with this Service Bulletin in the appropriate aircraft documents.
Fill out the electronic Service Bulletin reply form accessible from the ”Service Bulletin" page on the
Falcon portal or register SB implementation at Sbconfiguration@dassault-aviation.com, providing all
useful information for aircraft identification:
• aircraft type and serial number,
• SB compliance: complete or section(s) applied,
• remarks,
• compliance date,
• service center.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 16 / 42
DASSAULT AVIATION Proprietary Data

### Page 19

3. MATERIAL INFORMATION
NOTE: Compliance with this Service Bulletin by substituting the part numbers below with interchangeable
subsequent 
part numbers (as per the Master List or Dassault-approved supply list) is acceptable,
provided that subsequent part numbers have the same effectivity as the original ones.
A. MODIFICATION OF EQUIPMENT PART NUMBER
Kit P/N SBF7X0602C
Effectivity: All aircraft
NEW P/N QTY KEY WORD OLD P/N INSTRUCTION/DISPOSITION
7034056-1902 1 PROC module  (2-fig. 7)
7038231-2901 4 NIC/processor 7034057-1901  (3-fig. 7)
60000770-1907 4 AGM module 7036410-1903  (4-fig. 7)
7034056-1903 1 PROC module 7028419-1904  (5-fig. 7)
7038248-1901 mod
B or more
4 Power Supply Module 7024440-1901  (6-fig. 7)
7038622-1902 mod
A or more
4 Generic IO module 7025365-1901  Generic IO modules
(4101FY), (4201FY),
(4301FY) and (4401FY) (7-
fig. 7)
7038485-1901 1 Generic IO module 7025364-1901  generic I/O 5 module
(4501FY) (7-fig. 7)
7038630-1901 1 Control video IO 1
module
7026531-1902  (8-fig. 7)
7038472-1901 1 Control IO 2 module 7026534-1902  (9-fig. 7)
940-0452-001 with
software 
version
01/04 or subsequent
1 TCAS Computer 9003000-55005
60000091-983 2 NIM module 7517964-913
7027566-903 2 Bus coupler 7027566-901
940-000175-211 1 DLMU 7031051-902
071-50001-8103 2 TCAS antenna 7514081-913 (303NP)
7514081-914 
(203NP)
lower TCAS antenna
(503NP) / item 4
upper 
TCAS antenna
(603NP) / (8-fig. 9)
NOTE: Refer to Service Bulletin Commercial Summary to send back the modules removed.
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 17 / 42
DASSAULT AVIATION Proprietary Data

### Page 20

B. MODIFICATION KIT
Kit P/N SBF7X0601A
Effectivity: All aircraft
Electrical kit
Kit P/N SBF7X0601A - Electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
01C0K600-22P01 9 Contact 103NPE, 103NPF
01C0K501-20S01 2 Contact SP2102NH1
01C0K309-22DS01 5 Contact 751J, 4101FY1
01C0AFHE2-7 1 Hexashield backshell 4101FY1
01C0A3682FC22 2 Dummy contact 103NPE-11C/12G
01EQTPRL16B01 2 Splice L200SP
01EQTPRL08R01 5 Splice SP2102NH1, SP103NPF-7K,
SP103NPE-6J, 7J
01EQTRB23-1R 5 Soldering sleeve SP2102NH1, 103NPE
01EQTRB32-6A 1 Soldering sleeve L200SP
01PR0PRL05 1 Kit L200SP
01EQTEC1-1 10 Insulation cap
01CAN203-1-24W 1 m Wire
01CAB211-2-24 7.5 m Wire
01CAN211-1-24 12 m Wire
103NPE-10A/751J-34 2 Wire identification sleeve
(01PR0TMS1G1-8)103NPE-10E/751J-35 2
SP103NPE-6J/751J-36 2 Not used
103NPE-5E/SP103NPF-7K 2
103NPE-7A-7B/L200SP-43-44 2
4101FY1-20-21/L200SP-43-44 2
103NPE-15C-15D/2102NH-32-33 2
503NP1 1 Identification plate
01PR0TMSET1-0-10W4503NP2 1
503NP3 1
503NP4 1
603NP1 1
603NP2 1
603NP3 1
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 18 / 42
DASSAULT AVIATION Proprietary Data

### Page 21

Kit P/N SBF7X0601A - Electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
603NP4 1
503NP1 1 Self-adhesive label (STERLING
E19) Black marking on green
background503NP2 1
503NP3 1
503NP4 1
603NP1 1
603NP2 1
603NP3 1
603NP4 1
SP103NPF-7K 1 Splice identification sleeve
(01PR0TMS1G3-32)SP103NPE-6J 1
L200SP-43-44 1
01C0A507CPC11A8-01 4 Connector backplate  (1-fig. 2)
01C0F501U62BS001L 4 Connector  (2-fig. 3)
01C0A54148FC22 256 Blanking pin 2101FD, 2201FD, 2301FD,
2401FD
78750-00 16 Cable grip Identification plate
Kit P/N SBF7X0602A
Effectivity: All aircraft
Additional electrical kit
Kit P/N SBF7X0602A - Additional electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
01C0F38-3P16G08QS6-001 1 Connector kit 1001FP2
01C0R54148E7W25G08QPNL 1 Connector 87J
01C0R54148-6W25-08QSNL 1 Connector 87P
01C0R54148-0W09G05PNL 1 Connector 195J
01C0R54148-6W09G05SNL 1 Connector 195P
01C0R54148-0CF19-18QPNL 1 Connector 196J
01C0R54148-6CF19-18QSNL 1 Connector 196P
01C0CMBT6-639SN 1 Connector 204MP1
01C0CMBT7-639PN 1 Connector R5821FY
78780-10N 1 Back-plate 195J
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 19 / 42
DASSAULT AVIATION Proprietary Data

### Page 22

Kit P/N SBF7X0602A - Additional electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
78780-20N 1 Back-plate 196J
MS35206-216 6 screw 195J, 196J
01C0AMBT6-050SN 1 Impedance terminator R5821FY
01C0A507MAG8-8 1 Hexashield store 2505TC
01C0AFHE2-7 9 Hexashield backshell 2505TC1-13-14-15-17
2101FY1-12-27-41-42
2201FY1-12-27-41-42
2301FY1-12-27-41-42
2401FY1-12-27-41-42
1
101NZ1-62-63-81-82
1201NZ1-62-63-81-82
1001FP1-A1
1001FP1-A2
01C0K309-22DS01 34 Contact 2505TC1-13-14-15-17
2101FY1-8-12-27-41-42
2201FY1-8-12-27-41-42
2301FY1-8-12-27-41-42
2401FY1-8-12-27-41-42
1
101NZ1-62-63-81-82 and
1101NZ3-21
1201NZ1-62-63-81-82 and
1201NZ3-21
01C0K309-22DP01 6 Contact 196J
01C0K308-22DS01 6 Contact 86J
01C0K501C08P208 2 Contact 1001FP1-A1 and 1001FP1-A2
01C0K308Q08P665 12 Quadrax contact 87J, 195J, 196J
01C0K308Q08S665 15 Quadrax contact 87P, 195P, 196P, 1001FP2
01EQTRB23-1R 4 Soldering sleeve 86J, 196J
01C0A54148FC08 1 Dummy and sealing contact 87J
01C0A54148FC22 32 Dummy and sealing contact 196J/P, 2101FD2, 2201FD2,
2301FD2, 2401FD2, 101FW1
01C0A308-08RE638 1 Sealing boot 87J
01C0A308-08 14 Sealing plug 87P, 196P, 1001FP2
01EQTPRL08R01 6 Splice 1101NZ3-21
1201NZ3-21
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 20 / 42
DASSAULT AVIATION Proprietary Data

### Page 23

Kit P/N SBF7X0602A - Additional electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
2101FY1-8
2201FY1-8
2301FY1-8
2401FY1-8
01CAC665 50 m Quadrax cable
01CAC852 2 m Triaxial cable 1001FP1-A1/R5821FY and
1001FP1-A2/204MP1
01CAN211-1-24 2 m Wire 1101NZ3-21
1201NZ3-21
2101FY1-8
2201FY1-8
2301FY1-8
2401FY1-8
01CAB211-2-24 8 m Wire
01CAN203-1-22Y 0.6 m Wire
01PR0SCL1-8BK 0.5 m Heat-shrinkable sleeve LAN bus insulation caps (fig. 3)
01PR0RNE5-16TR 1 m Heat-shrinkable sleeve 2505TC1-13-14-15-17
2101FY1-12-27-41-42
2201FY1-12-27-41-42
2301FY1-12-27-41-42
2401FY1-12-27-41-42
1
101NZ1-62-63-81-82
1201NZ1-62-63-81-82
01PR0KYN1-16TR 1 m Heat-shrinkable sleeve 2505TC1-13-14-15-17
2101FY1-12-27-41-42
2201FY1-12-27-41-42
2301FY1-12-27-41-42
2401FY1-12-27-41-42
1
101NZ1-62-63-81-82
1201NZ1-62-63-81-82
01PR0KYN1-4TR 0.1 m Heat-shrinkable sleeve 1001FP1-A1
1001FP1-A2
86J-110-111/196J-A-R 2 Wire identification sleeve
(01PR0TMS1G1-8)86J-113-114/196J-N-L 2
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 21 / 42
DASSAULT AVIATION Proprietary Data

### Page 24

Kit P/N SBF7X0602A - Additional electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
1001FP1-A1/R5821FY 2 Wire identification sleeve
(01PR0TMS1G1-4)1001FP1-A2/204MP1 2
87J-A/1001FP2-8 2
87J-B/1001FP2-9 2
87J-C/1001FP2-10 2
87J-D/1001FP2-11 2
87J-E/1001FP2-4 2
87J-F/196J-F 2
87J-G/196J-K 2
2505TC1/87P-A 2
2301FY1/87P-B 2
2401FY1/87P-C 2
1201NZ1/87P-D 2
195J/1001FP2-3 2
195P/1101NZ1 2
196J-P/1001FP2-1 2
196P-P/2101FY1 2
196J-B/1001FP2-2 2
196P-B/2201FY1 2
87J 1 Self-adhesive label (STERLING
E19) 
Black marking on green
background87P 1
195J 1
195P 1
196J 1
196P 1
R5821FY 1
1001FP1 1 Identification plate
01PR0TMSET1-0-10W41001FP2 1
87J 1
87P 1
195J 1
195P 1
196J 1
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 22 / 42
DASSAULT AVIATION Proprietary Data

### Page 25

Kit P/N SBF7X0602A - Additional electrical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
196P 1
R5821FY 1
204MP1 1
78750-00 21 Cable grip Identification plates and
protective cap
78776-01 1 Spacer  (3-fig. 14)
78776-02 2 Spacer  (5-fig. 15)
78777-02 2 Spacer  (4-fig. 14) and (4-fig. 15)
01C0A501BE6-8D002 1 Protective cap
02C0A501CAP3-658 1 Hexashield hood 1001FP1
02PR0TSL090BK 4 m Braided sheath LAN routing on MAU/MRC
02PR0TSL160BK 5 m Braided sheath LAN routing on MAU/MRC
Kit P/N SBF7X0602B
Effectivity: All aircraft
Mechanical kit
Kit P/N SBF7X0602B - Mechanical kit
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
F7XC531522162 1 Connector bracket  (1-fig. 1 1)
F7XL531522159P01 1 Omega  (2-fig. 1 1)
35053-3205ID 4 Rivet  (3-fig. 1 1)
35053-3207ID 14 Rivet  (4-fig. 1 1 ), (5-fig. 11) and (2-fig.
14)
F7XL531522149A1E01 1 Bundle bracket  (1-fig. 12)
NAS1919M04S02AU 4 Rivet  (2-fig. 12) and (6-fig. 12)
78691-21-48C07 1 Bundle bracket  (3-fig. 12)
78771-001 1 Cable holder  (4-fig. 12)
21215DB3209J 1 Rivet  (5-fig. 12)
78757-03 1 Cable holder  (1-fig. 13)
21215DB3208J 1 Rivet  (2-fig. 13)
F7XC531842168 1 LAN terminal load bracket  (1-fig. 14)
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 23 / 42
DASSAULT AVIATION Proprietary Data

### Page 26

Kit P/N SBF7X0601B
Effectivity: All aircraft for TCAS antennas installation kit with external access only
Kit P/N SBF7X0601B
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
F7XL533403312W1 1 Interface shim  (1-fig. 8)
AG822000-02 2 Polyurethane gasket  (2-fig. 8)
F7XL536031024 1 Fuel equipment bay door item 1
NAS1133V8A 8 Screw lower TCAS antenna ( 503NP) /
item 2
NAS1149D0332K 8 Washer lower TCAS antenna ( 503NP) /
item 3
Kit P/N SBF7X0601C
Effectivity: All aircraft for TCAS antennas installation with internal and external access
Kit P/N SBF7X0601C
P/N QTY KEY WORD DISPOSITION/ITEM-FIG
35067-4008ID 14 Rivet  (1-fig. 9)
35067-3206ID 6 Rivet  (2-fig. 9)
35067-3209ID 6 Rivet  (3-fig. 9)
35067-3208ID 20 Rivet  (4-fig. 9)
35067-3207ID 3 Rivet  (5-fig. 9)
F7XL533403312W2 1 Interface shim  (6-fig. 9)
AG822000-02 2 Polyurethane gasket  (7-fig. 9)
F7XL536031024 1 Fuel equipment bay door item 1
NAS1133V8A 8 Screw lower TCAS antenna ( 503NP) /
item 2
NAS1133V12A 8 Screw upper TCAS antenna ( 603NP) / 
(9-fig. 9)
NAS1149D0332K 16 Washer lower TCAS antenna ( 503NP) /
item 3
upper 
TCAS antenna ( 603NP) / 
(10-fig. 9)
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 24 / 42
DASSAULT AVIATION Proprietary Data

### Page 27

C. SOFTWARE
NEW SOFTW
ARE/DATABASES
NEW SOFTWARE/DATABASES
NEW P/N SOFTWARE KEY WORD EFFECTIVITY SUPPLIER
TM7035297-107
EPIC Tools including:
•
Remote Terminal - RT 33, DLS 8.7.0
• APM Settings Tool - V 3.0
• APM Restoration Tool - V 2.2
All aircraft
HONEYWELL
through
DASSAUL
T
AVIATIONMM7034838-020
Operational Software
T
op Level System
Part Number
EB60007394-0116
Load 18.0
TT60005561-XXXXX APM Options parameter configuration
HONEYWELL
through
DASSAUL
T
AVIATION
PUB: 1002 18.0.1* LDI
DASSAULT
A
VIATION
available on
Falcon eData
Refer to Service Bulletin 7X-603 AMI database Aircraft withDatalink installed
GDC or ARINC
Direct or
SA
TCOM
DIRECT
PUB: 1002 V0015* FLT (Fault Codedatabase)
All aircraft
DASSAULT
A
VIATION
available on
Falcon eData
PUB: 1002 V0016*
OPS
(Consequences
database)
PUB: 1002 V0038* ECL Database
Full charts INDS ElectronicT erminal Charts
Integrated
Navigation
Data Service
(INDS)
EGPWF Data
DO69002412-0XXX*
(EGPWF Database) INDS EGPWF
Data996-0114-5XX*
(envelope modulation)
EGPWF Terrain Server
996-0146-XXX*
(terrain server)
INDS Terrain
server
DS7
or
DS7-YYCC-RRR*
or
INDS EPIC (1) for operatorwith RNP AR
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 25 / 42
DASSAULT AVIATION Proprietary Data

### Page 28

NEW SOFTWARE/DATABASES
NEW P/N SOFTWARE KEY WORD EFFECTIVITY SUPPLIER
DS8 (1) DS8-YYCC-RRR* (1)
AIRSPACE &
COMM
NA
VIGATION
DATA
OPS APPROVAL
(RNP AR=0.3 or
RNP AR DOWN
T
O RNP 0.1
APPROACH)
DM60004646-003* PS60004646-003* TOLD Database Aircraft with SB7X-41 1 HONEYWELL
through
DASSAUL
T
AVIATION
DM60002392-0007* PS60002392-0007* FMS AEDB
All aircraftDM60001004-0004* PS60001004-0004* Magvar
SWC69003872-040* 69003872-040* EGPWF ROAASDatabase
* or latest applicable version (the most current software and database versions which can be loaded on the aircraft are
now 
tracked in the "MAINTENANCE DOCUMENTATION - Documentation Status" section of the Falcon Portal, where
you will be given the most up-to-date versions depending on the aircraft configuration).
DATABASES P/N REQUIRED ONLY IF NOT PREVIOUSLY PROCURED
P/N SOFTWARE KEY WORD EFFECTIVITY SUPPLIER
DM60001005-0015*
PS60001005-0015*
ATC database Aircraft with SB7X-308
HONEYWELL
through
DASSAUL
T
AVIATION
PUB: 804 Latest applicable version ECB All aircraft DASSAULTA VIATION
PUB: 1002 P1182 Issue 1* ACMF
Optional but
recommended for
AP
troubleshooting
DASSAULT
A
VIATION
available on
Falcon eData
*or latest applicable version (the most current software and database versions which can be loaded on the aircraft are
now 
tracked in the "SOFTWARE & DATABASES - Software & Databases Status" section of the Falcon Portal, where
you will be given the most up-to-date versions depending on the aircraft configuration).
D.  LOCAL PROCUREMENT
NOTE: If specific products, identified in parentheses "()" are no longer procurable, equivalent
products can be used.
Paint substitutes are given in the Protection Scheme 
(Refer to SDS 20-60-00).
As indicated in Consumable Products Manual (CPM):
• cleaner
• alodine
• anti-corrosion primer
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 26 / 42
DASSAULT AVIATION Proprietary Data

### Page 29

• demolding agent
• AIREX foam
• compound EC 3524
• interlaying sealant
• covering sealant
• bead sealant
• white primer 5014
• lockwire
Contact P/N 01C0K309-22DS01 (4101FY3) - qty = 2 fig. 6
Wire 
identification sleeve P/N 01PR0TMS1G1-8 - Identification = SP103NPE-6J/751J-33 - qty = 2 fig.
6
SD card P/N TS32GSDHC1 (equivalent card may be used)
Hexashield backshell P/N 01C0AFHE3-7 if necessary to modifiy hexashields in connector 1101NZ-1 
fig. 4
FALCON 7X 7X -602
June 03, 2024 ATA 00
Initial issuance Page 27 / 42
DASSAULT AVIATION Proprietary Data

### Page 30 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
TOP VIEW
FR1  FR8 FR9  FR12  FR14
DLMU  MRC2
(NOT ILLUSTRATED)
87J/P  -751J/P
86J/P
87J/P: CONNECTOR LOCATION  ADAHRS  MAU2  L200SP  ITCAS
AND WIRES ROUTING
-SOLUTION 2
-SOLUTION 1
195J/P AND 196J/P: CONNECTORS LOCATION AND WIRES ROUTING
BEFORE  AFTER
FWD  FWD
Figure 1: WORK AREA
June 03, 2024  ATA 00
Initial issuance  Page 28 / 42

### Page 31 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
10000/1
GAU-I
2
Figure 2: AGM BACKSHELL
June 03, 2024  ATA 00
Initial issuance  Page 29 / 42

### Page 32 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
BEFORE MODIFICATION
FOR COMPLEMENT SEE WDM CHAP. 34-23-50
327J/P  LH FR33 LAN BUS CUT-OFF CONNECTOR  F33, LH
LH ASCB / RH ASCB CUT OFF CONNECTOR  CREW AREA, F1-8 UNDER FLOOR, C
LAN BUS LH/RH CUT-OFF CONNECTOR  CREW AREA, F1-F8 UNDER FLOOR
113J/P  LAN BUS LH/RH CUT-OFF CONNECTOR  CREW AREA, F1-F8 UNDER FLOOR
1010TP  MAINTENANCE PANEL  F8-9, OVER FLOOR, RH CABINET
2505TC  CMC MODULE  NOSE CONE, RH
1201NZ  NIM 2 MODULE  NOSE CONE, RH
NIM 1 MODULE  F8-12, UNDER CABIN FLOOR, RH
204MP  L5811FY REAR LAN TERMINAL LOAD  PRINTER COUPLER  F8-9, OVER FLOOR, RH CABINET  F41-44, SERVICING COMPT, LH.  R65 11 0 5 C
NIC/PROCESSOR 4 MODULE  NOSE CONE, KH
2301FY  2201FY  NIC/PROCESSOR 3 MODULE  NIC/PROCESSOR 2 MODULE  NOSE CONE, RH  F8-12, UNDER CABIN FLOOR  RA L5511FD MY 33
NIC/PROCESSOR 1 MODULE  F8-12, UNDER CABIN FLOOR
101FW  EGPWS 1 MODULE  F8-12, UNDER CABIN FLOOR
901FP  DMU  COCKPIT, SIDE CONSOLE, RH
R5511FD TERRAIN SERVER TERMINAL LOAD 2
L5511FD TERRAIN SERVER TERMINAL LOAD 1  NOSE CONE, LH
2401FD  AGM 4 MODULE  NOSE CONE, RH
2301FD  AGM 2 MODULE  NOSE CONE, RH  •: TERRAIN SERVER BUS
2201FD  AGM 3 MODULE  F8-12, UNDER CABIN FLOOR  *→: LAN BUS
2101FD  AGM 1 MODULE  F8-12, UNDER CABIN FLOOR
AFTER MODIFICATION
INCORPORATE IN WDM, CHAP. 34-23-50
327J/P  LH FR33 LAN BUS CUT-OFF CONNECTOR  F33, LH
120J/P  LH ASCB / RH ASCB CUT OFF CONNECTOR  CREW AREA, F1-8 UNDER FLOOR, C
114J/P  LAN BUS LH/RH CUT-OFF CONNECTOR  CREW AREA, F1-F8 UNDER FLOOR
113J/P  LAN BUS LH/RH CUT-OFF CONNECTOR  CREW AREA, F1-F8 UNDER FLOOR
1010TP  MAINTENANCE PANEL  F8-9, OVER FLOOR, RH CABINET
CMC MODULE
1201NZ  NIM 2 MODULE  NOSE CONE, RH
1101NZ  NIM 1 MODULE  F8-12, UNDER CABIN FLOOR, RH
PRINTER COUPLER:  F8-9, OVER FLOOR, RH CABINET
R5821FY LAN TERMINAL LOAD  F8-9, OVER FLOOR, RH CABINET
L5811FY  REAR LAN TERMINAL LOAD  F41-44, SERVICING COMPT, LH
NIC/PROCESSOR 4 MODULE  NOSE CONE. RH
2301FY  NIC/PROCESSOR 3 MODULE  NOSE CONE, RH
2201FY  NIC/PROCESSOR 2 MODULE  F8-12, UNDER CABIN FLOOR
NIC/PROCESSOR 1 MODULE  F8-12. UNDER CABIN FLOOR
101FW  EGPWS 1 MODULE  F8-12, UNDER CABIN FLOOR
1001FP  DLMU  COCKPIT, SIDE CONSOLE, RH
_5511FD TERRAIN SERVER TERMINAL LOAD 1  5511FD TERRAIN SERVER TERMINAL LOAD 2  NOSE CONE, LH  NOSE CONE. RHI  ADDED ELEMENTS
2401FD  AGM 4 MODULE  NOSE CONE, RH
2301FD.  AGM 2 MODULE  NOSE CONE. RH  : TERRAIN SERVER BUS  • WIRES CAPPED AND STOWED INSIDE THE BACKSHELLS.
2201FD  AGM 3 MODULE  F8-12, UNDER CABIN FLOOR  : LAN BUS  • WIRES CAPPED AND STOWED TO WIRING BUNDLE
2101FD  AGM 1 MODULE  F8-12, UNDER CABIN FLOOR  & WIRES CAPPED AND STOWED OUTSIDE THE BACKSHELLS
Figure 3: WDM 34-23-50 - WIRING MODIFICATION
June 03, 2024  ATA 00
Initial issuance  Page 30 / 42

### Page 33 (OCR)

DASSAULT  SERVICE BULLETIN
VIATION
FALCON 7X  7X -602
INCORPORATE IN WDM, CHAP. 23-10-00, 23-10-20, 34-23-50 & 45-90-00
FOR COMPLEMENT, SEE WDM CHAP. 23-10-00, 23-10-20 & 34-23-50
WIRING PROVIS
Figure 4: WDM 23-10-00, 23-10-20 & 45-90-00
June 03, 2024  ATA 00
Initial issuance  Page 31 / 42

### Page 34 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
BEFORE MODIFICATION
FOR COMPLEMENT, SEE WDM CHAP. 34-40-00 & 34-45-00  4191FY
103NP
TCAS/XPDR2 H
PROGRAM PIN COM  6K
A/C ALT 4000
A/C ALT 16000  6н
ALT ALT 32000
MALE VOIE  11C
OPTION PARITY  12G
RA N1 STATUS
TA/RA DISPLAY 1
TA/RA DISPLAY 2
39/20
203J5
PROG AUDIO LVL 6DB
PROG COMMON PIN OUT
RA VALID DISABLE
TOP ANT
TOP ANTENNA
203NP
153FT
BOT ANTENNA
303NP
SD 31-51-00, 45-32-00
UNLESS OTHERWISE SPECIFIED : ALL WIRE IS AWG 24  2102NH  102NH
• THE FOUR COAXIAL MUST HAVE THE SAME LENGTH.
1 THE FOUR COAXIAL MUST HAVE THE SAME LENGTH.
SHIELDED WIRES CONNECTED BY A TERMINAL JUNCTION OR SPLICE HAVE THE SHIELDING
JOINTED TOGETHER (THIS JUNCTION IS NOT ILLUSTRATED IN THIS WD
- 77J/P  LH FR1 BASIC ELEC CUT-OFF CONNECTOR  F1, LH
- 103NP  TCAS TRANSCEIVER  F12-16, UNDER CABIN FLOOR, LH
- 203NP  UPPER TCAS ANTENNA  F12-30, OVER CABIN FLOOR, LF
- 303NP  LOWER TCAS ANTENNA  F26-27, FUEL EQUIPMENT BAY
- 102NH  IRU 1  F19-20, IRS BAY
- 2102NH  ADAHRS UNIT  F8-12, UNDER CABIN FLOOR, LH
- 4101FY  GENERIC I/O 1 MODULE  F8-12, UNDER CABIN FLOOR
- 203J  TERMINAL STRIP  F8-9, OVER FLOOR, LH CABINET
Figure 5: WDM 34-40-00 & 34-45-00 - BEFORE WIRING MODIFICATION
June 03, 2024  ATA 00
Initial issuance  Page 32 / 42

### Page 35 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
FOR COMPLEMENT, SEE WDM CHAP. 34-40-00 & 34-45-00  AFTER MODIFICATION  INCORPORATE IN WDM, CHAP.34-40-00 & 34-45-00
103NP  4101FY.
751
A429 IRU1 HI  IRS1 RX H  IRS1 RX L
A429 IRU1 LO
TCAS/XPDR2 H
PROGRAM PIN COM
A/C ALT 4000  751
A/C ALT 16000  ALT ALT 32000  SP103NPE-6J/751J-38
MALE VOIE
OPTION PARITY
| L200SP
RA N1 STATUS
RANZ STATU
TAIRA DISPI AY
TA/RA DISPLAY 2  203J5
PROG AUDIO LVL 5DB  7B
PROG COMMON PIN OUT  7K  SP103NPF-7K
RA VALID DISABLE
TOP ANTENNA
603NP  3,22B
153FT
BOT ANTENNA
503NP  aPSt  TX1 IRS1 OUT 1H  TX1 IRS1 OUT
SD 31-51-00, 45-32-00  UNLESS OTHERWISE SPECIFIED: ALL WIRE IS AWG 24  2102NH  102NH
• THE FOUR COAXIAL MUST HAVE THE SAME LENGTH.
(2)  THE FOUR COAXIAL MUST HAVE THE SAME LENGTH.
SHIELDED WIRES CONNECTED BY A TERMINAL JUNCTION OR SPLICE HAVE THE SHIELDING
JOINED TOGETHER (THIS JUNCTION IS NOT ILLUSTRATED IN THIS WD)
- 77J/P  LH FR1 BASIC ELEC CUT-OFF CONNECTOR  F1, LH
• 751J  BASIC/OPTION CUT-OFF CONNECTOR  CABIN AREA, F14 UNDER FLOOR, RH
- 103NP  TCAS TRANSCEIVER  F12-16, UNDER CABIN FLOOR, LH
- 603NP  UPPER TCAS ANTENNA  F12-30, OVER CABIN FLOOR, LH
- 503NP  LOWER TCAS ANTENNA  F26-27, FUEL EQUIPMENT BAY
- L200SP  SPLICE ZONE  F9-12, UNDER CABIN FLOOR, LH  DELETED ELEMENTS
- 102NH  IRU 1  F19-20, IRS BAY  ADDED ELEMENTS
• 2102NH  ADAHRS UNIT  F8-12, UNDER CABIN FLOOR, LH  MODIFIED ELEMENTS
- 4101FY  GENERIC I/O 1 MODULE  F8-12, UNDER CABIN FLOOR
- 203J  TERMINAL STRIP  F8-9, OVER FLOOR, LH CABINET
Figure 6: WDM 34-40-00 & 34-45-00 - AFTER WIRING MODIFICATION
June 03, 2024  ATA 00
Initial issuance  Page 33 / 42

### Page 36 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
• 270
1123456  110/11/12 18 14 15 15) PS2 SLOT NO.
CH e
POWER SUPPLY 1  CONTROL/VIDEO NO  GENERIC  EGPWN T  PROCE  SUPFLY 2
0 00 0  •  000000000
]CHA
BEFORE MODIFICATION
1401FY
10 11 12 13 14  15 16 PS2 SLOT NO.
•CH B
POWER SUPPLY 1  CONTROL VO 2  SOR 4  SPARI
0 00000
CH A
1201FY
• SLOT NO
CH B
AFTER MODIFICATION  POWER SUPPLY 1  OONTROL/VIDEO I/0 1  GENERIC I/O 2  AGM  POWER SUPPLY 2
GENERIC
1 IN MAU1, PROCESSOR IN SLOT 16 MOVED TO SLOT 14
AND BECOME PROCESSOR 9.
© NEW P/N 7034056-1902 IS INSTALLED IN MAU1 SLOT 16,
ICH A
• IN MAU1 SLOT 16, PROCESSOR 7 BECOMES PROCESSOR 8 WITH NEW CFI
• IN MAU2 SLOT 16, PROCESSOR 8 BECOMES PROCESSOR 7 WITH NEW CFI
1 NIC PROCESSORS REPLACED BY NEW P/N.  IFY.
1 AGM MODULES REPLACED BY NEW PIN.  S EGPWM MODULE REPLACED BY PROCESSOR 10.  PS 112131-1587  INCT NO2 9 10 0 121509 13 181 PEZ SLOTNO
6 POWER SUPPLY MODULES REPLACED BY SAME P/N. WITH MOD B  OR MORE  AGM 4  SUPPLY 2
+ GENERIC IO MODULES REPLACED BY NEW P/N.
8 CONTROL/VIDEO IO 1 MODULE REPLACED BY NEW P/N.  POWER
9 CONTROL I/O 2 MODULE REPLACED BY NEW P/N.  890008  80008
CH A
Figure 7: MAU LAYOUT
June 03, 2024  ATA 00
Initial issuance  Page 34 / 42

### Page 37 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
12.7 mm (0.5 in)
400 mm (15.7 in) DIA
MICROBALLON TAPER SHIM LIMI
FWD
FR15  2 FR16
INISH PAINT LIMI  0 mm (0.79 ir
2.08m
- 15g m
8 mm
(0.31 in)
d, e, f  INTERLAYING SEALANT
BEAD SEALANT  B-B
COVERING SEALANT
- WHITE PRIMER 5014
Figure 8: UPPER TCAS ANTENNA - INSTALLATION WITH EXTERNAL ACCESS ONLY
June 03, 2024  ATA 00
Initial issuance  Page 35 / 42

### Page 38 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
12.7 mm (0.5 in)
9, 10
100 mm (15.7 in) DIA
FWDI  MICROBALLON TAPER SHIM LIN
1 mm
(3.19 in)
FR15  FR16
WIDTH=5 mm
0 mm (0.79 in)
FINISH PAINT LIN
OR1 bOR2
15 mm
(0.59 in)
WIDTH=5 mm  WIDTH=5 mm  *031 in)
a OR 1  35067-4008ID
b OR 2  35067-3206ID  e, f, g  INTERLAYING SEALANT
B-B
c OR 3  35067-3209ID  BEAD SEALANT
d OR 4  35067-3208ID  COVERING SEALANT
WIDTH=5 mm
5  35067-3207ID  WHITE PRIMER 5014
Figure 9: UPPER TCAS ANTENNA - INSTALLATION WITH INTERNAL AND EXTERNAL ACCESS
June 03, 2024  ATA 00
Initial issuance  Page 36 / 42

### Page 39 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
FR1
EXAMPLE OF FRONT PLATE
(A/C WITHOUT M111)
<1 mm
(0.83 in)  52 mm
|(2.05 in)
SOLUTION 2
Ø 45 mm
| (1.77 in)  |(2.05 in)  52 mm
SOLUTION 1
21 mm
(0.83 in)
Ø 45 mm
(1.77 in)
56 mm
(2.2 in)
Figure 10: FRAME 1 - CUT-OFF CONNECTOR 87 J/P
June 03, 2024  ATA 00
Initial issuance  Page 37 / 42

### Page 40 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
AFTER  FR9
FR8-
[FWD
FWD
48 mm
BEFORE  AFTER  (1.89 in)
24 mm
(0.95 in)
6 mm
(0.24 in)
5
48 mm  9 mm
(1.89 in)  (0.35 in)
Figure 11: FRAME 8/9 - CONNECTORS SUPPORT INSTALLATION
June 03, 2024  ATA 00
Initial issuance  Page 38 / 42

### Page 41 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
AFTER  AFTER
FWD
BEFORE  AFTER
5
8 mm  1 mm
(0.3 in)  (0.05 in)
Figure 12: FRAME 8/9 - BUNDLES SUPPORT INSTALLATION
June 03, 2024  ATA 00
Initial issuance  Page 39 / 42

### Page 42 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
55 mm
(2.2 in)
25 mm  (1 in)
Figure 13: FRAME 8/9 - CABLE HOLDER INSTALLATION
June 03, 2024  ATA 00
Initial issuance  Page 40 / 42

### Page 43 (OCR)

DASSAULT  SERVICE BULLETIN
VIATION
FALCON 7X  7X -602
38 mm
(1.5 in)
LAN TERMINAL LOAD
- DLMU
Figure 14: LAN TERMINAL LOAD SUPPORT INSTALLATION
June 03, 2024  ATA 00
Initial issuance  Page 41 / 42

### Page 44 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 7X  7X -602
Figure 15: FRAME 9 - LAN ROUTING
June 03, 2024  END OF DOCUMENT  ATA 00
Initial issuance  Page 42 / 42

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
