# Dassault Service Bulletin SB-F10-337: No revision named

- Rights: © Dassault Aviation. Filed by the FAA in regulations.gov docket FAA-2020-0448, the docket of AD 2020-17-14. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Dassault Service Bulletin SB-F10-337](https://openairdocs.org/service-documents/dassault/sb-f10-337.md)
- Title as filed: SB-F10-337
- Pages: 14
- PDF: https://openairdocs.org/files/sha256/a5/2a/a52aabfa2a151936c942544787f26bed9d7a98c68b807064742de5216422c8e5
- Page: https://openairdocs.org/service-documents/dassault/sb-f10-337/file/a52aabfa2a15

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

FALCON 10
No 337
MARCH 22, 2019
MANDATORY
ATA 27-36
FLIGHT CONTROLS
HYDRAULIC SYSTEM
HYDRAULIC #2 PIPE ROUTING AND PROTECTION
FALCON SERVICE BULLETIN
Copyright © 2019 by Dassault Aviation
All rights reserved. No part of this work may be reproduced or copied
in any form or by any means without written permission
of Dassault Aviation.
026

### Page 2

FLIGHT CONTROLS
HYDRAULIC SYSTEM
HYDRAULIC #2 PIPE ROUTING AND PROTECTION
Initial issuance March 22, 2019
List of effective pages :
1 to 10
FALCON 10 F10 -337
F10 -27-36

### Page 3

FLIGHT CONTROLS
HYDRAULIC SYSTEM
HYDRAULIC #2 PIPE ROUTING AND PROTECTION
 
1. PLANNING INFORMATION
A. EFFECTIVITY
This Service Bulletin is applicable to all FALCON 10 aircraft.
B. REASON
In the wings, interference between rib passage hole (Rib 1 to Rib 2a) and hydraulic #2 pipes and
chafing between pipes has been identified.
The purpose of this Service Bulletin is to suppress interference at rib passage hole and chafing along
the hydraulic #2 pipe.
C. DESCRIPTION
The Service Bulletin is divided into two sections:
Section F10-337-1:
The operation consists in checking:
• no interference between ribs passage hole (Rib 1 to Rib 2a) and hydraulic #2 pipes
• no chafing between pipes.
Section F10-337-2:
The operation consists in installing spiral binding on pipe forward of ribs passage hole and adding a
grommet around ribs passage hole.
D. COMPLIANCE
This Service Bulletin is mandatory as prescribed by the Airworthiness Authorities of the country of
registration of the aircraft.
E. APPROVAL
This Service Bulletin covers DASSAULT AVIATION modification F10 M953 that has been approved
under the authority of DOA nr. EASA.21J.051.
The technical content of this document is approved under the authority of DOA nr. EASA.21J.051.
F. LABOR
Estimated labor-hours: Refer to Service Bulletin Commercial Summary.
NOTE: These labor-hours only concern the work described in this Service Bulletin and do not include
other maintenance work that may be performed on this occasion.
G. MATERIAL - PRICE AND AVAILABILITY
The modification kit may be obtained from either address listed below:
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 1 / 10
DASSAULT AVIATION Proprietary Data

### Page 4

Western hemisphere: DASSAULT FALCON JET CORP.
SPARES DISTRIBUTION CENTER
200 RISER ROAD
LITTLE FERRY, NJ 07643 U.S.A.
Telephone:
• CANADA and U.S.A.: 1-800-800-4036
• MEXICO: 001-800-800-4036
• Other countries: 1-201-541-4809
Fax:
• CANADA and U.S.A.: 1-800-800-4817
• MEXICO: 001-800-800-4817
• Other countries: 1-201-440-7021
Other continents: DASSAULT AVIATION
Falcon Spares
54, AVENUE MARCEL DASSAULT
B.P. 24
33701 MERIGNAC Cedex (FRANCE)
Please contact your Dassault Aviation
Account Representative
Telephone: 33 (0)5.56.18.44.44
E/H dafsorders@dassault-aviation.com
Price and availability on request.
H. WEIGHT AND BALANCE
Change in weight: None.
Change in balance with respect to 25% MAC: None.
I. REFERENCES
Aircraft Maintenance Manual:
• 7-10-00 - AIRCRAFT JACKING
• 20-00-05 - SUMMARY OF MANDATORY PRECAUTIONS TO BE TAKEN DURING AIRCRAFT
MAINTENANCE OPERATIONS
• 29-00-01 - SERVICING - INSTRUCTIONS FOR REPLACEMENT OF A HYDRAULIC
COMPONENT
• 53-50-00 - AERODYNAMIC FAIRINGS
• 57-55-01 - REMOVAL/INSTALLATION REPLACEMENT OF THE FLAPS - DETAILED
INSPECTION OF THE LH AND RH INBOARD FLAP AND RIBS
Stuctural repair manuel:
• 51-20-09 - BASIC SEALING METHODS
• 51-30-05 - DRILLING
Illustrated Parts Catalog:
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 2 / 10
DASSAULT AVIATION Proprietary Data

### Page 5

• 27-13-05-01 - SYSTEM ASSEMBLY - SERVO HYDRAULIC
J. OTHER PUBLICATIONS AFFECTED
None.
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 3 / 10
DASSAULT AVIATION Proprietary Data

### Page 6

2. ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INSTRUCTIONS AND SAFETY PRECAUTIONS
(1) Obey the Structural Repair Manual:
• Basic sealing methods (Refer to SRM 51-20-09).
• Drilling (Refer to SRM 51-30-05).
B. PRELIMIRARY STEPS
(1) The aircraft must be in the maintenance configuration (Refer to procedure 20-00-05).
(2) Remove the LH and RH inboard flaps (Refer to procedure 57-55-01).
(3) Remove the removable protector in the LH/RH wells ( fig. 3).
C. SECTION F10-337-1: INSPECTION
NOTE: The procedure is applicable to LH and RH wings. Operations are described at LH wing (RH
wing is symmetrical).
(1) Check that there is fig. 1:
• no interference between hydraulic #2 pipes (items 260-430 LH side IPC 27-13-05 FIGURE
1), and Rib 1 to Rib 2a passage hole,
• no chafing between hydraulic #2 pipes (items 260-430 LH side IPC 27-13-05 FIGURE 1),
• no interference with pipe F10A758451 and bellcranck on right side.
(a) If no interference and no chafing are found, install :
• grommet on Rib 1c and 2a passage hole with sealant for bonding purpose,
• spiral binding along the two pipes betwween Rib 1b and Rib 2a in accordance with fig.
2.
(b) If interference or chafing is found, applied SECTION F10-337-2.
D. SECTION F10-337-2: CHECK PIPES AND ADD PROTECTIONS
NOTE: The procedure is applicable to LH and RH wings. Operations are described at LH wing (RH
wing is symmetrical).
(1) Jack the aircraft (Refer to procedure 7-10-00).
(2) Remove Rear lateral fairing 175JL/175JR (Refer to procedure 53-50-00).
(3) Remove the riveted wing lower panel at track 1 ( fig. 3) and (fig. 4).
CAUTION: TAKE CARE NOT TO OVALIZE THE BORES IN THE SKIN AND SUB-STRUCTURE
WHEN COUNTERDRILLING FASTENERS.
NOTE: Control the bores to determine the out-of tolerances to provide oversize fasteners.
(4) Remove the pipes (items 260/270 and 430/440) (Refer to IPC 27-13-05 Fig. 1) and (Refer to
procedure 29-00-01).
NOTE: Mark the pipes in front of Rib 1b.
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 4 / 10
DASSAULT AVIATION Proprietary Data

### Page 7

After removal, check that there are no marks or chafing on pipes:
• If no marks and no chafing are found, go to step 2.C.(2).
• If marks or chafings on pipes are found, determine the depth of mark as follows:
• If depth ≤ 0.1 mm (0.004 in), smooth the surface with water abrasive paper  within
tolerance limit.
• If depth > 0.1 mm (0.004 in), discard the pipe.
(5) Install grommet edging on holes Rib 1 (side Rib 1a), Rib 1a, Rib 1c and 2a with sealant for
bonding purpose (fig. 2).
(6) Install spiral binding along the two pipes in accordance with fig. 2.
(7) Install the pipes (items 260/270 and 430/440) (Refer to IPC 27-13-05 Fig. 1) and (Refer to task
29-00-01), at Rib 1b, the clamps must be installed in accordance with fig. 2.
(8) Install the lower panel at track 1 with interlaying sealant. The fasteners are installed with
interlaying sealant under the head (fig. 4).
NOTE: If some bores are out-of tolerance, enlarge to repair size.
E. FINAL STEPS
(1) Install Rear lateral fairing 175JL/175JR (Refer to procedure 53-50-00-0).
(2) Install the removal protector in the LH/RH well ( fig. 3).
(3) Install the LH and RH inboard flaps (Refer to procedure 57-55-01).
F. RECORDING
Record compliance with this Service Bulletin in the appropriate aircraft documents.
Fill out the card located at the end of the Service Bulletin and mail or fax it to Dassault Aviation or
Dassault Falcon Jet, or fill out the electronic Service Bulletin reply form located in the ”Service Bulletin"
page on the Falcon portal.
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 5 / 10
DASSAULT AVIATION Proprietary Data

### Page 8

3. MATERIAL INFORMATION
NOTE: Compliance with this Service Bulletin by substituting the part numbers below with interchangeable
subsequent part numbers (as per the Master List) is acceptable, provided that subsequent part
numbers have the same effectivity as the original ones.
A. MODIFICATION KIT
Kit P/N SBF10-0337A
NEW P/N QTY KEY WORD
SBPTFE4 or SP-PTFE 5 m Spiral binding
MS21266-1T 2 Grommet edge
Replacement of pipes
NEW P/N QTY KEY WORD
F10A758301 1 LH pipe (return)
F10A758351 1 LH pipe (pressure)
F10A758401 1 RH pipe (return)
F10A758451 1 RH pipe (pressure)
Kit P/N SBF10-0337B for Rear lateral fairing installation
NOTE: If the LH and RH are removed two kits are necessary
NEW P/N QTY KEY WORD ITEM-FIG
NAS1921M05S02WU 18 Blind rivet  (1-fig. 4) 
NAS1921M05S03WU 3 Blind rivet  (2-fig. 4) 
MS90353S0604 1 Blind bolt  (3-fig. 4) 
21218DE3210 97(+10) Rivet  (4-fig. 4) 
21218DE4010 21(+5) Rivet  (5-fig. 4) 
B. LOCAL PROCUREMENT
As indicated in Consumable Products Manual (CPM):
• water abrasive paper
• sealant for bonding purpose
FALCON 10 F10 -337
March 22, 2019 F10 -27-36
Initial issuance Page 6 / 10
DASSAULT AVIATION Proprietary Data

### Page 9 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 10  F10 -337
Rib 2a  Rib1c  Rib1b  Rib1a  Rib1
LH SIDE / RH SYMMETRICAL
Passage hole Rib1  Passage hole Rib1a  Passage hole Rib 1b  Passage hole Rib1c  Passage hole Rib2a
Passage hole Rib1 RH SIDE
Interference between bellcranck
and pipe.
Figure 1: LH SIDE INSPECTION
March 22. 2019  F10-27-36
Initial issuance  Page 7 / 10

### Page 10 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 10  F10 -337
Rib 1  Rib 1a  Rib 1b  Rib 1c  Rib 2a
50(2 in.)  50 (2 in.)  100(4 in.) _
Section with spiral binding  Section with spiral binding
Grommet installation
Rib 1b clamps installation
Figure 2: SPIRAL BINDING AND GROMMET INSTALLATION
March 22, 2019  F10 -27-36
Initial issuance  Page 8 / 10

### Page 11 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 10  F10 -337
Removable protector
Riveted wing Jower panel
F/C23  Rail 1
False spar datum line  F/C21  F/C22  - Rib 1a
- Rib 1b
Fairing door
Figure 3: WING LOWER PANEL LOCATION
March 22, 2019  F10 -27-36
Initial issuance  Page 9 / 10

### Page 12 (OCR)

DASSAULT  SERVICE BULLETIN
AVIATION
FALCON 10  F10 -337
*
* *
‡ ‡
Detail applicable for LH side only
LH skin looking up (RH side symmetric except detail)
) * Rivet F 100° dia 32
) * Rivet F 100° dia 32 - countersunk rivetting
* Rivet F 100° dia 4
* Rivet MLS F 100° dia 397
4 Rivet HUCK dia 4 76
• Screw F 100° dia 48
VIS
Figure 4: WING LOWER PANEL FASTENERS
March 22, 2019  F10 -27-36
END OF DOCUMENT
Initial issuance  Page 10 / 10

### Page 13 (OCR)

NO POSTAGE
NECESSARY
FROM  IF MAILED
IN THE
UNITED STATES
ZIP CODE
BUSINESS REPLY MAIL
FIRST CLASS MAIL PERMIT NO. 3306 HACKENSACK, NJ 07602
POSTAGE WILL BE PAID BY ADDRESSEE:
DASSAULT FALCON JET CORP.
PO BOX 1946
SO HACKENSACK NJ 07606-9946
ATTENTION:
FIELD SERVICE DEPARTMENT
DASSAULT AVIATION
78, Quai Marcel Dassault
Cedex 300
92552 SAINT-CLOUD Cedex
FRANCE
A l'attention de DSC

### Page 14

SERVICE BULLETINS COMPLIANCE FALCON 10 A/C S/N    
DASSAULT AVIATION Number  ATA Number   
F10 337  F10 27 36   
        
        
        
        
Coding: C complete compliance
 
T partial compliance
   
Performed by:   
Remarks: Initial issuance Date: Signature:
SERVICE BULLETINS COMPLIANCE
Would you be kind enough to inform us that this Service Bulletin is complied with:
- For "Western Hemisphere", mail upper card (No postage necessary if mailed in the U.S.A.) or fax to Dassault Falcon Jet: 1-201-541-4700.
- For "Other Continents", mail card herebelow or fax to Dassault Aviation: 33 (0)1.47.11.65.21.
On the occasion, if other Service Bulletins have been simultaneously complied with could you complete the blank spaces provided for this
purpose.
APPLICATION DE BULLETINS DE SERVICE
Lorsque vous aurez applique ce Bulletin de Service sur votre avion, veuillez avoir l'amabilite de nous en informer:
- Utiliser la carte reponse superieure pour continent americain (Dispensee de timbrage pour postage depuis les U.S.A.) ou le fax pour
Dassault Falcon Jet : 1-201-541-4700.
- Ou la carte reponse inferieure pour autres continents ou le fax pour Dassault Aviation : 33 (0)1.47.11.65.21.
Eventuellement, si d'autres Bulletins de Service ont ete appliques simultanement, vous pouvez les mentionner dans les cases vierges
prevues a cet effet.
APPLICATION DES BULLETINS DE SERVICE   
SERVICE BULLETINS COMPLIANCE FALCON 10 A/C S/N    
DASSAULT AVIATION Number
Numero DASSAULT AVIATION  
ATA Number
Numero ATA   
F10 337  F10 27 36   
        
        
        
        
Coding: C complete complianceapplication totale
 
T partial complianceapplication partielle
   
Performed by:
Fait par:
  
Remarks: Initial issuance Date: Signature:
Remarques: Edition originale

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
