# Diamond Aircraft Mandatory Service Bulletin 40NG-018: No revision named

- Rights: © Diamond Aircraft. Filed by the FAA in regulations.gov docket FAA-2013-0348, the docket of AD 2013-08-21. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Diamond Aircraft Mandatory Service Bulletin 40NG-018](https://openairdocs.org/service-documents/diamond/40ng-018.md)
- Title as filed: U.S. DOT/FAA - WI-MSB 40NG-018
- Pages: 10
- PDF: https://openairdocs.org/files/sha256/b3/c2/b3c2051abdbe8d7bc0a490adc7847eb14f613a83554488deaeb326e4ee23cc2c
- Page: https://openairdocs.org/service-documents/diamond/40ng-018/file/b3c2051abdbe

## Text

This text is OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 1 of 10
Austria  26-Nov-2012
WORK INSTRUCTION
WI-MSB 40NG-018
GENERAL INFORMATION
1.1  Subject
Replacement of charge air tubes.
1.2  Reference Documents
DA 40 NG Airplane Maintenance Manual, Doc. No. 6.02.15, latest effective issue.
Diamond aircraft SI 40NG-007 Installation and tightening torque of worm drive clamps.
1.3  Remarks
a) All work must be done by a certified aircraft service station or a certified aircraft
maintenance mechanic.
b) All work, in particular if not described in this work instruction, must be done in accordance
with the referenced maintenance manual.
c) For conversion factors between SI units and US/Imperial units refer to AMM Chapter 02.
d) In case of doubt, contact Diamond Aircraft Industries GmbH.
DRAWINGS, SPECIAL TOOLS & MATERIALS
I.1  Drawings
None.
II.2 Special Tools
None.

### Page 2 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  A-2700 Wiener Neustadt  N. A. Otto-Straße 5  Page 2 of 10  Revision 1
Austria  26-Nov-2012
П.З  Material
If RSB 40NG-011 or MAM 40-506 or MAM 40-502 was carried out, use the material below:
Quantity  Part Number  Description
1  D44-8122-20-00_2  Turbo Connector Assy
1  D44-8126-00-05_2  Charge Air Tube
1  DIN 3771 46.2x3.55  O-Ring
MVQ 70
8  TORRO_60-80_12_W1  Worm drive Clamps
If RSB 40NG-011 or MÄM 40-506 or MAM 40-502 was NOT carried out, use the material below:
Quantity  Part Number  Description
1  D44-8126-00-08  Charged Air Hose
1  D44-8122-00-10_1  Elbow 45° (Hose)
8  TORRO_60-80_12_W1  Worm Drive Clamps
1  DIN 933-M8x16-YZP  Hexagon head screw
D44-8122-20-00_2  Turbo Connector Assy
1  D44-8126-00-05_2  Charge Air Tube
1  DIN 3771 46.2x3.55  O-Ring
MVQ 70
Material is available from Diamond Aircraft Industries.

### Page 3 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 3 of 10
Austria  26-Nov-2012
INSTRUCTIONS
| If RSB 40NG-011 or MÄM 40-506 or MÄM 40-502 was carried out:
Make sure AMM-TR-MÄM 40-530 has been incorporated into the AMM.
2  Remove cowlings (i.a.w. AMM section 71-10).
WARNING  DO NOT STAND WITHIN THE DANGER AREA OF THE PROPELLER. IF
THE ENGINE STARTS, THE PROPELLER CAN CAUSE DEATH OR
INJURY TO PERSONS.
WARNING  MAKE SURE THAT THE ENGINE IS SAFE BEFORE YOU WORK ON THE
ENGINE CONTROLS. IF THE PROPELLER TURNS IT CAN CAUSE
INJURY TO PERSONS.
3  Remove current charge air tubing between turbo charger and intercooler:
• Remove and discard all used (8) worm drive clamps on the turbo connector assy
D44-8122-20-00 and the charge air tube D44-8126-00-05_1.
• Remove and discard the turbo connector assy D44-8122-20-00 (including o-ring) and
charge air tube D44-8126-00-05_1.
4  Install charge air tube D44-8126-00-05_2 and turbo connector assy D44-8122-20-00_2
(refer to SI 40NG-007 latest revision).
• Install the Turbo Connector Assy including o-ring DIN 3771 46.2x3.55 MVQ 70.
Do NOT tighten the V-Clamp at the turbo charger at this time.
• Install the charge air hose D44-8126-00-08 to the turbo connector assy D44-8122-20-
• Install the charge air tube D44-8126-00-05_2 to the charge air hose D44-8126-00-08
and move the 8 new worm drive clamps into position (refer to SI 40NG-007 latest
revision).
• Connect the charge air tube D44-8126-00-05_2 to the charge air hose
D44-8122-00-10_1.
CAUTION  DO NOT TIGHTEN THE WORM DRIVE CLAMPS WITH THE ENGINE
BEING HOT. THIS CAN DAMAGE THE SILICONE HOSES AND MAY
RESULT IN LOSS OF ENGINE POWER.

### Page 4 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
N. A. Otto-Straße 5  Revision 1
AIRCRAFT
A-2700 Wiener Neustadt  Page 4 of 10
Austria  26-Nov-2012
5  Position the charge air tube and turbo connector assy.
Make sure that the charge air tube has at least 12mm clearance to the firewall and at
least 5mm clearance to the coolant tube aft of the engine (refer to Figure 1 and 2
below).
Firewall -
Min. 12 mm
Charge Air Tube
Min. 5mm Clearance
Coolant Tube RSGU Clamp
Figure 1: Clearance between charge air tube to firewall and coolant tube
• Make sure that the charge air tube has at least 5mm clearance to the oil line aft of the
engine (refer to Figure 2 below).
Minimum
Clearance
5mm
Figure 2: Attachment of charge air tube

### Page 5 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 5 of 10
Austria  26-Nov-2012
6  Make sure the Alternate Air Bowden Cable is routed as shown in figures 3 and 4.
Figure 3: Bowden Cable Installation - Top View
Figure 4: Bowden Cable Installation - View from RH side

### Page 6 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 6 of 10
Austria  26-Nov-2012
Tighten worm drive clamps (SI 40NG-007, latest revision):
• Position and tighten the worm drive clamps on the charge air hoses D44-8122-00-10_1
and D44-8126-00-08 according to SI 40NG-007 latest revision.
CAUTION  DO NOT TIGHTEN THE WORM DRIVE CLAMPS WITH THE ENGINE
BEING HOT. THIS CAN DAMAGE THE SILICONE HOSES AND MAY
RESULT IN LOSS OF ENGINE POWER.
• Apply torque seal on the worm drive clamps (see Figure 3 below).
Figure 5: Worm drive clamp torque seal
• Tighten the V-clamp on the turbo connector assy with 5 Nm.
8  Clean working areas, check for foreign objects.
9  Check all altered, replaced, repaired parts for proper function.
10  Test all systems in working area for function.
11  Make all necessary entries in the airplane logs.
| If RSB 40NG-011 or MÄM 40-506 or MÄM 40-502 was NOT carried out:
12  Make sure AMM-TR-MÄM 40-530 has been incorporated into the AMM.
13  Remove cowlings (i.a.w. AMM section 71-10).
WARNING  DO NOT STAND WITHIN THE DANGER AREA OF THE PROPELLER. IF
THE ENGINE STARTS, THE PROPELLER CAN CAUSE DEATH OR
INJURY TO PERSONS.
WARNING  MAKE SURE THAT THE ENGINE IS SAFE BEFORE YOU WORK ON THE
ENGINE CONTROLS. IF THE PROPELLER TURNS IT CAN CAUSE
INJURY TO PERSONS.

### Page 7 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 7 of 10
Austria  26-Nov-2012
14  Remove current charge air tubing:
• Remove and discard all used (8) worm drive clamps between turbo charger and
intercooler.
• Remove and discard the charge air elbow hose SNS5X-0-60_72-90°.
• Remove the turbo adapter D44-8126-70-01 from turbo charger.
• Remove the P-clamp, which holds the charged air tube on the air filter box
(refer to Figure 4 below).
Figure 6: Attachment of charged air tube
• Remove and discard charge air tube D44-8126-00-05.
• Remove and discard charge air hose D44-8122-00-10.
15  Install charge air tube D44-8126-00-05_2 and turbo connector assy D44-8122-20-00_2
(refer to SI 40NG-007, latest revision).
• Install the hexagonal head screw DIN 933-M8x16-YZP with washer into the air filter box
where the P-clamp was previously removed.
• Install the Turbo Connector Assy including o-ring DIN 3771 46.2x3.55 MVQ 70.
Do NOT tighten the V-Clamp at the turbo charger at this time.
• Install the charge air hose D44-8126-00-08 to the turbo connector assy D44-8122-20-
•  Install the charge air tube D44-8126-00-05_2 to the charge air hose D44-8126-00-08
and move the 8 new worm drive clamps into position (refer to SI 40NG-007, latest
revision).
•  Connect the charge air tube D44-8126-00-05_2 to the charge air hose
D44-8122-00-10_1
CAUTION  DO NOT TIGHTEN THE WORM DRIVE CLAMPS WITH THE ENGINE
BEING HOT. THIS CAN DAMAGE THE SILICONE HOSES AND MAY
RESULT IN LOSS OF ENGINE POWER.

### Page 8 (OCR)

Diamond  Diamond Aircraft Industries Gmbh  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 8 of 10
Austria  26-Nov-2012
16  Position the charge air tube and turbo connector assy.
Make sure that the charge air tube has at least 12mm clearance to the firewall and at
least 5mm clearance to the coolant tube aft of the engine (refer to Figure 7 and 8
below).
Firewall -
Min. 12 mm
Charge Air Tube
Min. 5mm Clearance
Coolant Tube RSGU Clamp
Figure 7: Clearance between charged air tube to firewall and coolant tube
• Make sure that the charge air tube has at least 5mm clearance to the oil line aft of the
engine (refer to Figure 8 below).
Minimum
Clearance
5mm
Figure 8: Attachment of charged air tube

### Page 9 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 9 of 10
Austria  26-Nov-2012
17  Make sure the Alternate Air Bowden Cable is routed as shown in figures 9 and 10.
Figure 9: Bowden Cable Installation - Top View
Figure 10: Bowden Cable Installation - View from RH side

### Page 10 (OCR)

Diamond  Diamond Aircraft Industries GmbH  WI-MSB 40NG-018
AIRCRAFT  N. A. Otto-Straße 5  Revision 1
A-2700 Wiener Neustadt  Page 10 of 10
Austria  26-Nov-2012
18  Tighten worm drive clamps (SI 40NG-007, latest revision):
• Position and tighten the worm drive clamps on the charge air hoses D44-8122-00-10_1
and D44-8126-00-08 according to SI 40NG-007 latest revision.
CAUTION  DO NOT TIGHTEN THE WORM DRIVE CLAMPS WITH THE ENGINE
BEING HOT. THIS CAN DAMAGE THE SILICONE HOSES AND MAY
RESULT IN LOSS OF ENGINE POWER.
• Apply torque seal on the worm drive clamps (see Figure 11 below).
Figure 11: Worm drive clamp torque seal
• Tighten the V-clamp on the turbo connector assy with 5 Nm.
19  Clean working areas, check for foreign objects.
20  Check all altered, replaced, repaired parts for proper function.
21  Test all systems in working area for function.
22  Make all necessary entries in the airplane logs.
23  Make all necessary entries in the airplane logs.

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
