# Diamond Aircraft Mandatory Service Bulletin 42-129: No revision named

- Rights: © Diamond Aircraft. Filed by the FAA in regulations.gov docket FAA-2017-0506; AD 2017-11-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Diamond Aircraft Mandatory Service Bulletin 42-129](https://openairdocs.org/service-documents/diamond/sb-42-129.md)
- Title as filed: SB42-129-M-r0  Inspection of Exhaust Pipe
- Pages: 5
- PDF: https://openairdocs.org/files/sha256/93/5b/935be1bc4f74d2b324d6dc16c8dcba547cfda3f5fc1fae204d80de68fcfd17bd
- Page: https://openairdocs.org/service-documents/diamond/sb-42-129/file/935be1bc4f74

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Diamond Aircraft Industries GmbH 
N. A. Otto-Straße 5 
2700 Wiener Neustadt, Austria 
DAI MSB 42-129
Page 1 of 5
17-May-2017
 
 
MANDATORY SERVICE BULLETIN 
MSB 42-129 
I TECHNICAL DETAILS 
I.1 Category 
Mandatory. 
I.2 Airplanes affected 
Type:   DA 42, DA 42 M 
Serial numbers:  42.004 through 42.427 
    42.AC001 through 42.AC151 
    42.M001 through 42.M027 
Only airplanes with a TAE 125-02-99 or TAE 125-02-114 engine with exhaust pipe                 
DAI P/N D60-9078-06-01_01 / Technify P/N 52-7810-H0014 01 installed are affected. 
I.3 Date of effectivity 
17-May-2017 
I.4 Time of Compliance 
For exhaust pipes 
- with more than 40 hours TSN (time since new) at the date of effectivity: within next              
10 flight hours and every 50 flight hours thereafter, 
- with less than 40 hours TSN at the date of effectivity: before exceeding 50 flight hours and 
every 50 flight hours thereafter. 
I.5 Subject 
Inspection of exhaust pipe. 
ATA-Code: 78-00 
I.6 Reason 
An exhaust pipe without a directly attached integral heat shield was developed allowing visual 
inspection over the entire exhaust pipe length (refer also to DAI OSB 42-122). Heat shielding 
is provided through patches and shields in the cowling. Diamond Aircraft received reports 
about cracked exhaust pipes which if not detected can cause loss of the exhaust pipe. 
This Service Bulletin prescribes inspection of the exhaust pipe to identify possible cracks and 
to replace the exhaust pipe in case cracks are found.

### Page 2

Diamond Aircraft Industries GmbH 
N. A. Otto-Straße 5 
2700 Wiener Neustadt, Austria 
DAI MSB 42-129
Page 2 of 5
17-May-2017
 
 
I.7 Concurrent Documents 
None. 
I.8 Approval 
The technical information or instructions contained in this document relate to the Design 
Change Advisories No. MÄM 42-911 and OÄM 42-252/d, which have been approved under 
the authority of EASA Design Organization Approval ref. EASA.21J.052. 
The technical content of this document has been approved under the authority of DOA ref. 
EASA.21J.052. 
I.9 Accomplishments / Instructions 
1. Remove engine cowling for engine installations with affected exhaust P/N installed       
i.a.w. AMM section 71-10. 
2. Inspect exhaust pipe circumferentially in marked area for cracks. 
 
3. If cracks are found replace exhaust pipe or one time repair as follows: 
Cracks up to 50 mm (2 inch) in axial direction may be one time weld-repaired: TIG 
welding using 1.4842 filler material and staff qualified according to ISO 24394. 
No re-welding of the manifold joint is allowed. 
NOTE: Weld repaired exhaust pipes remain subject to the recurring inspection.

### Page 3

Diamond Aircraft Industries GmbH 
N. A. Otto-Straße 5 
2700 Wiener Neustadt, Austria 
DAI MSB 42-129
Page 3 of 5
17-May-2017
 
 
NOTE: Following types of cracks are 
 
acceptable for repair,      
               
 
NOT acceptable for repair. 
              
 
The dot-dashed line indicates position & orientation of the crack.

### Page 4

Diamond Aircraft Industries GmbH 
N. A. Otto-Straße 5 
2700 Wiener Neustadt, Austria 
DAI MSB 42-129
Page 4 of 5
17-May-2017
 
 
 
 
4. Clean working areas, check for foreign objects. 
5. Check all altered, replaced, repaired parts for proper function. 
6. Test all systems in working area for function. 
7. Install engine cowlings i.a.w. AMM section 71-10. 
8. Make all necessary entries in the airplane logs. 
 
I.10 Mass (Weight) and CG 
The change in mass and CG is negligible. 
II PLANNING INFORMATION 
II.1 Material and Availability 
Materials are available from Technify Motors. 
II.2 Special Tools 
None. 
II.3 Labour Effort 
Approx. 0.5 hours for inspection. 
II.4 Credit 
None. 
II.5 Reference Documents 
DA 42 Series Airplane Maintenance Manual, Doc. No. 7.02.01, latest effective issue. 
 
III REMARKS 
1. All work must be done by a certified aircraft service station or a certified aircraft 
maintenance mechanic. 
2. All work, particular that which is not especially described in this Service Bulletin, must be 
done in accordance with the referenced Maintenance Manual. 
3. Completion of all work must be recorded in the log book. 
4. In case of doubt contact Diamond Aircraft Industries GmbH.

### Page 5

Diamond Aircraft Industries GmbH 
N. A. Otto-Straße 5 
2700 Wiener Neustadt, Austria 
DAI MSB 42-129
Page 5 of 5
17-May-2017
 
 
 
 
EXECUTION REPORT TO 
SERVICE BULLETIN 
MSB 42-129 
 
 
AIRPLANE INFORMATION 
Airplane Serial Number          _________________ 
Airplane Registration    _________________ 
Airplane Operator    _________________ 
Hours of operation of airplane  _________________ 
No. of landings    _________________ 
Hours of operation-engine   _________________ 
Typical operation of airplane       private, club, training, other ______________ 
 
Cracks found on exhaust:                no □             yes □ 
Weld repair carried out:                   no □             yes □ 
 
 
 
 
 
__________________________________ 
Date, Name, Sign 
 
 
 
 
Please e-mail the completed form executionreports@diamond-air.at

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
